Multilink issue on Cisco 7609
Hi,
We tried to create 2 x Multilinks between OSR's, but due to some issues only 1 Multilink comes up and the other was failing during negotiatiation. We need to create 2 multilinks between two sites,
Need support that why we are unable to create more than 1 multilink.
It would be easier to identify the issue if you provide details of how it was configured and any error messages that might have been issued.
HTH
Rick
Similar Messages
-
Calling issue with Cisco 7937 conference station
Hi Friends,
I am facing issue wiht Cisco 7937 conference station, our customer have various branch offices accross the world. All branches are connected over MPLS through service provider( SIP service provider) . there is a centralized CUCM and remote office have SIP Voice gateways .
When making calls from once remote site to another using Cisco 6921 phones calls working fine
When making calls from once remote site to another using Cisco 7937 conference station to make call any phone at remote office, calls are getting disconneted, remote phone rings when calls, but its gets fast busy tone when other party picks up the phone and not able to talk.
I suspect the issue with Codec but we have configured transcoders in VG and registered with CUCM
Please help me if any one experience such issue earlier.
Regards
Sivahi Basant,
1. Actually tow phones A and B are registerd with centralized CUCM, A and B are located in two different locations, RTP traffic between And B pass through service provider.
Call Flow --> Phone A ---->CUCMRouterpattern--> SIP trunk ----> Voice gateway--->Service provider cloud---> Respective Voice Gateway---> CUCM -- Phone B
Show Run
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.02.27 15:14:52 =~=~=~=~=~=~=~=~=~=~=~=
sh run
Building configuration...
Current configuration : 12139 bytes
! Last configuration change at 06:35:59 UTC Tue Feb 25 2014
! NVRAM config last updated at 11:16:38 UTC Mon Feb 24 2014 by administrator
! NVRAM config last updated at 11:16:38 UTC Mon Feb 24 2014 by administrator
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname eucamvgw01
boot-start-marker
boot system flash:c2900-universalk9-mz.SPA.151-4.M5.bin
boot-end-marker
card type e1 0 0
logging buffered 51200 warnings
no logging console
no aaa new-model
no network-clock-participate wic 0
no ipv6 cef
ip source-route
ip traffic-export profile cuecapture mode capture
bidirectional
ip cef
ip multicast-routing
ip domain name drreddys.eu
ip name-server 10.197.20.1
ip name-server 10.197.20.2
multilink bundle-name authenticated
stcapp ccm-group 2
stcapp
stcapp feature access-code
stcapp feature speed-dial
stcapp supplementary-services
port 0/1/0
fallback-dn 5428025
port 0/1/1
fallback-dn 5428008
port 0/1/2
fallback-dn 5421462
port 0/1/3
fallback-dn 5421463
isdn switch-type primary-net5
crypto pki token default removal timeout 0
voice-card 0
dsp services dspfarm
voice call send-alert
voice call disc-pi-off
voice call convert-discpi-to-prog
voice rtp send-recv
voice service voip
ip address trusted list
ipv4 10.198.0.0 255.255.255.0
ipv4 152.63.1.0 255.255.255.0
address-hiding
allow-connections sip to sip
no supplementary-service h225-notify cid-update
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
fax-relay ans-disable
sip
rel1xx supported "track"
privacy pstn
no update-callerid
early-offer forced
call-route p-called-party-id
voice class uri 100 sip
host 41.206.187.71
voice class codec 10
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 ilbc
codec preference 4 g729r8
codec preference 5 g729br8
voice class codec 20
codec preference 1 g729br8
codec preference 2 g729r8
voice moh-group 1
moh flash:moh/Panjo.alaw.wav
description MOH G711 alaw
multicast moh 239.1.1.2 port 16384 route 10.198.2.9
voice translation-rule 1
rule 1 /^012237280\(..\)/ /54280\1/
rule 2 /^012236514\(..\)/ /54214\1/
rule 3 /^01223651081/ /5428010/
rule 4 /^01223506701/ /5428010/
voice translation-rule 2
rule 1 /^00\(.+\)/ /+\1/
rule 2 /^0\(.+\)/ /+44\1/
rule 3 /^\([0-9].+\)/ /+\1/
voice translation-rule 3
rule 1 /^9\(.+\)/ /\1/
rule 2 /^\+44\(.+\)/ /0\1/
rule 3 /^\+\(.+\)/ /00\1/
voice translation-rule 4
rule 1 /^54280\(..\)/ /12237280\1/
rule 2 /^54214\(..\)/ /12236514\1/
rule 3 /^\+44\(.+\)/ /\1/
rule 4 /^.54280\(..\)/ /12237280\1/
rule 5 /^.54214\(..\)/ /12236514\1/
voice translation-rule 9
rule 1 /^\(....\)/ /542\1/
voice translation-rule 10
voice translation-rule 11
rule 1 /^\+44122372\(....\)/ /542\1/
rule 2 /^\+44122365\(....\)/ /542\1/
voice translation-rule 12
voice translation-rule 13
rule 1 /^\([18]...\)/ /542\1/
voice translation-rule 14
voice translation-profile MPLS-incoming
translate calling 10
translate called 9
voice translation-profile MPLS-outgoing
translate calling 11
translate called 12
voice translation-profile PSTN-incoming
translate calling 2
translate called 1
voice translation-profile PSTN-outgoing
translate calling 4
translate called 3
voice translation-profile SRST-incoming
translate calling 14
translate called 13
license udi pid CISCO2921/K9 sn FGL145110RE
hw-module ism 0
hw-module pvdm 0/0
username administrator privilege 15 secret 5 $1$syu5$DsxdOgfS7Wltx78o4PV.60
redundancy
controller E1 0/0/0
ip tcp path-mtu-discovery
ip scp server enable
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description internal LAN
ip address 10.198.2.9 255.255.255.0
duplex auto
speed auto
interface ISM0/0
ip unnumbered GigabitEthernet0/0
service-module ip address 10.198.2.8 255.255.255.0
!Application: CUE Running on ISM
service-module ip default-gateway 10.198.2.9
interface GigabitEthernet0/1
description to TATA NGN
ip address 115.114.225.122 255.255.255.252
duplex auto
speed auto
interface GigabitEthernet0/2
description SIP Trunks external
ip address 79.121.254.83 255.255.255.248
ip access-group SIP-InBound in
ip traffic-export apply cuecapture size 8000000
duplex auto
speed auto
interface ISM0/1
description Internal switch interface connected to Internal Service Module
no ip address
shutdown
interface Vlan1
no ip address
ip forward-protocol nd
no ip http server
no ip http secure-server
ip route 0.0.0.0 0.0.0.0 10.198.2.1
ip route 10.198.2.8 255.255.255.255 ISM0/0
ip route 41.206.187.0 255.255.255.0 115.114.225.121
ip route 77.37.25.46 255.255.255.255 79.121.254.81
ip route 83.245.6.81 255.255.255.255 79.121.254.81
ip route 83.245.6.82 255.255.255.255 79.121.254.81
ip route 95.223.1.107 255.255.255.255 79.121.254.81
ip route 192.54.47.0 255.255.255.0 79.121.254.81
ip access-list extended SIP-InBound
permit ip host 77.37.25.46 any
permit ip host 83.245.6.81 any
permit ip host 83.245.6.82 any
permit ip 192.54.47.0 0.0.0.255 any
permit icmp any any
permit ip host 95.223.1.107 any
deny ip any any log
control-plane
voice-port 0/1/0
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/1
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/2
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/3
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
no ccm-manager fax protocol cisco
ccm-manager music-on-hold bind GigabitEthernet0/0
ccm-manager config server 152.63.1.19 152.63.1.100 172.27.210.5
ccm-manager sccp local GigabitEthernet0/0
ccm-manager sccp
mgcp profile default
sccp local GigabitEthernet0/0
sccp ccm 10.198.2.9 identifier 3 priority 3 version 7.0
sccp ccm 152.63.1.19 identifier 4 version 7.0
sccp ccm 152.63.1.100 identifier 5 version 7.0
sccp ccm 172.27.210.5 identifier 6 version 7.0
sccp
sccp ccm group 2
bind interface GigabitEthernet0/0
associate ccm 4 priority 1
associate ccm 5 priority 2
associate ccm 6 priority 3
associate ccm 3 priority 4
associate profile 1002 register CFB_UK_CAM_02
associate profile 1001 register XCODE_UK_CAM_02
associate profile 1000 register MTP_UK_CAM_02
dspfarm profile 1001 transcode
codec ilbc
codec g722-64
codec g729br8
codec g729r8
codec gsmamr-nb
codec pass-through
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 18
associate application SCCP
dspfarm profile 1002 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 1000 mtp
codec g711alaw
maximum sessions software 200
associate application SCCP
dial-peer cor custom
name SRSTMode
dial-peer cor list SRST
member SRSTMode
dial-peer voice 100 voip
description *** Inbound CUCM ***
translation-profile incoming PSTN-incoming
incoming called-number .
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 500 voip
description *** Inbound TATA MPLS ***
translation-profile incoming MPLS-incoming
session protocol sipv2
session target sip-server
incoming called-number ....
incoming uri from 100
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 510 voip
description *** Outbound TATA MPLS ***
translation-profile outgoing MPLS-outgoing
destination-pattern 54[013-9]....
session protocol sipv2
session target ipv4:41.206.187.71
session transport udp
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 520 voip
description *** Outbound TATA MPLS ***
translation-profile outgoing MPLS-outgoing
destination-pattern 5[0-35-9].....
session protocol sipv2
session target ipv4:41.206.187.71
session transport udp
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 200 voip
description *** Inbound M12 *** 01223651081, 01223651440 - 01223651489
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 0122365....
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 201 voip
description *** Inbound M12 *** 012237280XX
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 012237280..
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 202 voip
description *** Inbound M12 *** 01223506701
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 01223506701
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 210 voip
description *** Outbound M12 ***
translation-profile outgoing PSTN-outgoing
destination-pattern +...T
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 211 voip
description *** Outbound ISDN for SRST and emergency ***
translation-profile outgoing PSTN-outgoing
destination-pattern 9.T
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 212 voip
description *** Outbound ISDN for emergency ***
translation-profile outgoing PSTN-outgoing
destination-pattern 11[02]
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 2000 voip
description *** Outbound to CUCM Primary ***
preference 1
destination-pattern 542....
session protocol sipv2
session target ipv4:152.63.1.19
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 2001 voip
description *** Outbound to CUCM Secondary ***
preference 2
destination-pattern 542....
session protocol sipv2
session target ipv4:152.63.1.100
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 2002 voip
description *** Outbound to CUCM Teritiary ***
preference 3
destination-pattern 542....
session protocol sipv2
session target ipv4:172.27.210.5
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 999010 pots
service stcapp
port 0/1/0
dial-peer voice 999011 pots
service stcapp
port 0/1/1
dial-peer voice 999012 pots
service stcapp
port 0/1/2
dial-peer voice 999013 pots
service stcapp
port 0/1/3
sip-ua
no remote-party-id
gatekeeper
shutdown
call-manager-fallback
secondary-dialtone 9
max-conferences 4 gain -6
transfer-system full-consult
ip source-address 10.198.2.9 port 2000
max-ephones 110
max-dn 400 dual-line no-reg
translation-profile incoming SRST-incoming
moh flash:/moh/Panjo.ulaw.wav
multicast moh 239.1.1.1 port 16384 route 10.198.2.9
time-zone 22
time-format 24
date-format dd-mm-yy
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 131
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
session-timeout 60
exec-timeout 60 0
privilege level 15
login local
transport input all
line vty 5 15
session-timeout 60
exec-timeout 60 0
privilege level 15
login local
transport input all
scheduler allocate 20000 1000
ntp server 10.1.30.1
end
eucamvgw01#
Sh SCCP
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.03.03 17:57:44 =~=~=~=~=~=~=~=~=~=~=~=
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0
IPv4 Address: 10.198.2.9
Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 10.198.2.9, Port Number: 2000
Priority: 3, Version: 7.0, Identifier: 3
Call Manager: 152.63.1.19, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 4
Trustpoint: N/A
Call Manager: 152.63.1.100, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 5
Trustpoint: N/A
Call Manager: 172.27.210.5, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 6
Trustpoint: N/A
MTP Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1000
Reported Max Streams: 400, Reported Max OOS Streams: 0
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
TLS : ENABLED
Transcoding Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1001
Reported Max Streams: 36, Reported Max OOS Streams: 0
Supported Codec: ilbc, Maximum Packetization Period: 120
Supported Codec: g722r64, Maximum Packetization Period: 30
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: gsmamr-nb, Maximum Packetization Period: 60
Supported Codec: pass-thru, Maximum Packetization Period: N/A
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
Conferencing Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1002
Reported Max Streams: 16, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
TLS : ENABLED
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070080
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070081
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070082
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070083
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
eucamvgw01# -
issue with cisco acs 4.2.Users unable to login aaa client but after restarting group policy able to login
issue with cisco acs 4.2.Users unable to login aaa client but after restarting group policy able to login
-
Directory Caching issue with Cisco Jabber client for Windows
Hi ,
I am facing cache issue with Cisco Jabber client for Windows. If I do any change related to modification or deletion of contacts in Active Directory/ Callmanager, it does not reflect in the Jabber. Because jabber takes the contacts from the locally stored cache file in the Windows system.
Every time I have to remove the cache file to overcome this issue, practically it's not possible to do the same with all the Widows users. As, if any employee leaves the company and still I can see his contact appears in the "Cisco Jabber client". I have not seen this issue with Android/Apple iOS.
Is there any automated way to remove the cache file?
Here is the detail of CUCM,Presence and Jabber.
CUCM version: 9.1.x
Presence : 9.1.X
Jabber : 10.5 and 10.6Hello
On our environment we had to install a dedicated Microsoft Certificate Authority "just for Cisco Jabber usage" to house the
Network Device Enrollment Service.
Our certificate for the CUPS were generated on this Certification Authority too.
I discussed this certificate matter with my colleagues this afternoon and nobody seems to remember how these certificates were deployed into the
Enterprise Trust store for the users.
But I think they asked all 400 users to accept the 3 certificates by answering "yes" to the popup instead of using a script deployed by GPO...
I wish you success with that deployment and really hope you have a technical partner that *Knows* this subject.
Our partner left us alone with that unfortunately.
Florent
EDIT: If the "Certutil script method" works, please let me know. This could be useful in our own deployment. -
Routing issue between Cisco Nexus and Cisco 4510 R+E Chassis
We have configured Cisco Nexus 7K9 as core and Cisco 4510 R+E as access switches for Server connectivity.
We are experiencing problem in terms of ARP learning and Ping issues between Cisco Nexus and end hosts.Hi,
So you have N7k acting as L3 with servers connected to 4510?.
Do you see the MAC associated with failing ARP in 4510?. Is it happening with all or few servers?. Just to verify if it is connectivity issue between N7k and 4510, you can configure an SVI on 4510 and assign address from same raneg (server/core range) and perform a ping.
This will help narrow down if issue is between server to 4510 or 4510 to N7k.
Thanks,
Nagendra -
MacBook and MacBook Pro with 10.6: Wireless Airport Issues with Cisco
Long Story but please bear with me:
Loaded SL on my daughters MacBook and my MacBook Pro. Internet worked flawlessly at our house (WEP encrypted) and on other public wifi. When my daughter went back to her sorority house at college 24 hours later, she could not access the internet using the sorority house network (Cisco Aironet 1800 router and Cisco Airo Access Points).
Her Airport on the MacBook appeared connected at full strength yet no internet. Two calls to Apple support (they were very nice) did not help. All the following were tried:
1. Reset PRAM
2. Deleted Airport and Safari plists
3. Edited locations
4. Removed Battery
5. Others I cannot now remember
Still no net. However, she could 'pirate' and hop on line with other identified public wifi adjacent to the sorority house. I drove to the sorority house today and tried to get on the network wirelessly using my MacBook Pro with SL. Same identical results to hers. Another MacBook without SL works great and gets right on the network.
Is this some SL influenced issue with the Airport card and the Cisco system? Weird that both of our laptops work great with several other wifi networks but not the one at the sorority house.
Could much of what we all our seeing with the internet access problem lie not with issues within our software or computers but with the routers and access points not being compatible? I have very little understanding of this stuff (as you all can probably tell) but the Apple Support people acted like it was a old firmware issue with Cisco and not with SL. Not actually what I wanted to hear.
Any ideas or suggestions?Your description there, particularly the last part, sounds like my problem. At home, we connect using Airport and ADSL which was OK, once SL had sorted out passwords.
At my office, where there are two wifi systems, I could not get on either, although did have IP numbers on both. The link to the outside world is via a proxy which uses a PAC file. Network Diagnostics reported each time (whatever I did) that the link to the server was OK, but the Internet was not.
I created a new Location with identical settings (typing them in and not copying) and the only visible difference is that the new location has no DNS numbers -- I had not noticed that before. The moment I pressed, Apply, the computer was online.
I was guessing that there was a conflict in a .plist file somewhere; but now I wonder if DNS might have been the reason (the DNS number usually used is the one from the router itself). -
Issue with cisco ONS 15310. Slot with Ethernet ports, designed for bridging.
Hi, guys. I’ve got an issue with cisco ONS 15310 sdh optical network. I’ve got a special slot with Ethernet ports, designed for bridging. Assume, we’ve got to multiplexers, named A and B with ports A0 and B0 respectively. The ios console of these slots says, the configuration is as follows:
no ip address set on these ports
Ports are administratively up
Auto mdix
Bridge groups are the same on these ports.
Dot1q tunnel.
I’m trying to monitor a device with an ip-address connected to port B0. It answers ping if I connect the notebook directly to a device. But if I connect the notebook to port A0 and ping the device pluged in port B0 through the optical network, it doesn’t answer. I tried connections with straight and cross cable.
Guys, who set the network said, it should work as a point to point bridge with no extra configuration. But it doesn’t. I used wireshark sniffer to lookup what’s happening on port A0. All I see is cdp-s from port A0 and self-announcements of the notebook.
Any suggestions? Thank you in advance.B
Building configuration...
Current configuration : 3712 bytes
! Last configuration change at
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname B
boot-start-marker
boot-end-marker
enable password -
clock timezone -
ip subnet-zero
no ip domain-lookup
no mpls traffic-eng auto-bw timers frequency 0
bridge 100 protocol ieee
bridge 140 protocol ieee
bridge 141 protocol ieee
bridge 142 protocol ieee
bridge 143 protocol ieee
bridge 144 protocol ieee
interface Loopback0
ip address 192.x.0.x 255.255.255.255
interface FastEthernet0
description -
no ip address
mode dot1q-tunnel
bridge-group 140
bridge-group 140 spanning-disabled
interface FastEthernet1
description --- B0 ---
no ip address
mode dot1q-tunnel
bridge-group 141
bridge-group 141 spanning-disabled
interface FastEthernet2
description -
no ip address
mode dot1q-tunnel
bridge-group 142
bridge-group 142 spanning-disabled
interface FastEthernet3
description -
no ip address
mode dot1q-tunnel
bridge-group 143
bridge-group 143 spanning-disabled
interface FastEthernet4
description -
no ip address
mode dot1q-tunnel
bridge-group 144
bridge-group 144 spanning-disabled
interface FastEthernet5
no ip address
shutdown
interface FastEthernet6
no ip address
shutdown
interface FastEthernet7
description -
no ip address
shutdown
mode dot1q-tunnel
bridge-group 100
bridge-group 100 spanning-disabled
interface POS0
description -
no ip address
crc 32
interface POS0.1
encapsulation dot1Q 141
no snmp trap link-status
bridge-group 141
interface POS0.2
encapsulation dot1Q 142
no snmp trap link-status
bridge-group 142
interface POS0.3
encapsulation dot1Q 143
no snmp trap link-status
bridge-group 143
interface POS0.4
encapsulation dot1Q 144
no snmp trap link-status
bridge-group 144
interface POS0.5
description -
encapsulation dot1Q 140
no snmp trap link-status
bridge-group 140
interface POS1
no ip address
crc 32
interface POS1.1
encapsulation dot1Q 100
no snmp trap link-status
bridge-group 100
router ospf 100
log-adjacency-changes
network 192.x.0.x 0.0.0.0 area 0
ip default-gateway [x.x.x.x]
ip classless
no ip http server
snmp-server community public RO
snmp-server ifindex persist
snmp-server trap link ietf
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps config
snmp-server enable traps cpu threshold
snmp-server enable traps entity
snmp-server enable traps syslog
snmp-server enable traps hsrp
snmp-server enable traps config-copy
snmp-server enable traps bridge
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps bgp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps ipmulticast
snmp-server enable traps rtr
snmp-server enable traps mpls traffic-eng
snmp-server enable traps mpls ldp
snmp-server enable traps rsvp
snmp-server enable traps l2tun session
snmp-server enable traps mpls vpn
snmp-server host x.x.x.x public
control-plane
line con 0
line vty 0 4
password -
logging synchronous level 4
login
end -
Cisco 7609 router received higher traffic than upstream provider router is sending
Hi all,
I have a Cisco 7609 router that connects to our upstream provider router using 3rd party DWDM Fiber backhaul provider.
The upstream provider router is a Juniper router that had capped our port speed to 1.1Gbps, the backhaul provider didn't capped our port speed and the maximum speed is 2Gbps since it's a 2x1Gbps port channel interface.
I have noticed that our 7609 router able to receive traffic that exceeds 1.1Gbps, and the highest traffic able to received is 1.3Gbps and more.
I have crossed checked the MRTG graph provided by our upstream provider as well as our PRTG graph and indeed we are receiving higher bandwidth than our upstream provider is sending.
I'd like to know if anyone know how it is possible to receive traffic that is higher than what the neighbor router is sending?
RegardsHi at all,
We found a solution for this Problem !!
We always and always got this error:
%PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
The problem was the cable! The following pin-out is required:
1 ----- 1
2 ----- 2
3 ----- 6
4 ----- 5
5 ----- 4
6 ----- 3
7 ----- 7
8 ----- 8
We used this and the fault has disappeared!!
The only problem that still exists:
After the first connection the router must be rebooted because otherwise no more additional session is established.
Thanks for all answers.
Regards,
Mario -
Cisco 7609-S/ME3600X port shaping
Hello everyone
I am using the folloing configuration on Cisco ME36000X for port shaping
policy-map TEST_OUT_10MB
class class-default
shape average 10000000
policy-map TEST_IN_10MB
class class-default
police 10000000
interface GigabitEthernet0/2
switchport trunk allowed vlan none
switchport mode trunk
load-interval 30
service instance 101 ethernet
encapsulation untagged
service-policy input TEST_IN_10MB
service-policy output TEST_OUT_10MB
bridge-domain 101
interface Vlan101
bandwidth 10000
ip address xxx.xxx.xxx.xxx 255.255.255.252
I have applyed also the same port shaping on an Cisco 7609-S with an 7600-ES+20G3CXL
policy-map TEST_10MB
class class-default
police 10000000
shape average 10000000
interface GigabitEthernet1/11
bandwidth 10000
ip address xxx.xxx.xxx.xxx 255.255.255.252
load-interval 30
service-policy input TEST_10MB
service-policy output TEST_10MB
When i am downloading a file and capturing the traffic with wireshark there is significant difference on Cisco 7609-S graph with that one on Cisco ME3600X. Both have the same internet connection.
Is there any way to fine tune Cisco ME3600X to have the same behavior like Cisco 7609-S?
Regards
Antonis.I have not that graph so I am just guessing that you are noticing the difference between policing and shaping. It seems to me you are applying these techniques on each platform on a different way. Try to shape/police in the same order or only to shape.
Hope to help
Alessio
Sent from Cisco Technical Support iPad App -
Ethernet cfm: question on RDI allarm cisco 7609
Hi all,
I have ethernet cfm configured on two Cisco 7609s and two UP MEPs configured under xconnect PW MPLS on the same domain, level and service MA so they became CFM peers.
I notice that after removing and re-configuring olny one UP MEP under xconnect PW, the Cisco 7609 send a SYSLOG message indicating a RDI defect alarm and the show ethernet cfm errors showed RDI defect too.
Aftert 18 seconds this alarm is cleared and the show ethernet cfm errors is empty.
I don't undestand this behaviour..why the Cisco send the RDI alarm in this situation?Have you opened a TAC case for it ?
Can you share output of:
show module 1 -
I have a cisco 7609 router it Communication Media Module WS-SVC-CMM card,when i do (show module) im seeing the card there but when i want to configure the card like i type (card type the iso is not recognising it but i downloaded the latest version of the IOS and upgrade it but stiil,can any one help.
try 12.2 SB series.
regards
shivlu jain -
LAG configuration issue on Cisco SG300 52 Switch
Hi everybody,
I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine. However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports? Or is there any compatibility issue?
Any help from you guys will be greatly appreciated.
Thank you.
VishalHi Dave,
Thank you for your quick response and sorry to have looked at it late. Well, I already resolved the issue and like you pointed out, it was the configuration of the Dell NICs. I had to configure NIC teaming and there was a bug with the Broadcom NIC management software. I had to download this piece of software again and I was then able to configure NIC teaming on it. I initially thought that it was already configured because we got the Dell server "pre-installed with pretty much everything".
Anyway thank you for your assistance. Oh I have a question though if you don't mind clearing my doubt. We have bought 7 of these SG300 Switches and I would like to use all of them
in a hierarchical design as core, distribution and access layer switches because I believe this switch has got all the qualities to be used at all the three layers. We have about 100 users in our company at the moment but expecting growth of about 10-20 employees per year. Would you think a hierarchical network design for a 100 users is a bit of an overkill? Would you think these SG300 switches can handle network traffic at the distribution and core layers? I worked out the average daily traffic is only about 4 Mbps.
Thank you for your valuable guidance.
Kind regards,
Vishal
Date: Mon, 12 Sep 2011 08:09:40 -0600
From: [email protected]
To: [email protected]
Subject: - Re: LAG configuration issue on Cisco SG300 52 Switch
Cisco Support Community
Re: LAG configuration issue on Cisco SG300 52 Switch created by David Hornstein in Small Business Switches - View the full discussion
Hi Chundunsing,
Thank you for the purchase of my switch.
Chundunsing, I love the way you worded your question ; "I am having an issue with LAG configuration on a Cisco SG300 52 switch." ,but seriously you are having a problem with interfacing the dell with my switch.
You have LAG working to the Dell R710 teamed NICs and god knows what NICs or drivers you are using to acheive this.
Now LAG is providing , load balancing between the LAG ports.
Now LAG is providing , link redundancy for connectibity to the Dell R710.
If there is a configuration issue , it sure seems the way you have it configured without LACP is still working. But you have the option when you create a LAP group to enable LACP. You can see this as a tick box in the LAG group.
But might i also install, recently firmware version 1.1.1.8, just came out.
Please be sure to;
Step 1. update the firmware on the switch and
Step 2. select it as the 'active image.'
Step 3 rebbot the switch to utilize this active image.
If you are having any trouble doing this the admin guide references how to achieve this. for your concenience I have atteched the guide to this posting.
regards Dave
Reply to this message by going to Cisco Support Community
Start a new discussion in Small Business Switches at Cisco Support Community -
Is there any known issues with Cisco Meraki APs with client devices which publish PMF support in probe requests ? We are seeing connectivity issues with Cisco Meraki MR12,MR16 and MX80 models . Please update if there are any known issue with these APs.
Thanks for your thoughts, Nathan. We do actually have the "Enable Fast Reconnect" option selected on our wireless profile. Good idea, though.
We did also (originally) have 2 RADIUS servers defined within our wireless network. What we discovered was that each Meraki AP will try each one in order, top-to-bottom, and then primarily use the server that responded to it first. So, if for any reason you have a short-lived issue with your local RADIUS server responding to requests, and the AP is able to talk to a remote RADIUS server (in our case, one on the other side of the world) instead, the AP will elect to use the remote RADIUS server instead. In our case, the latency is high enough between these APs and this remote RADIUS server that while a client is roaming between APs, and having to re-authenticate, the entire process breaks down because (1) the client is moving between APs faster than the remote RADIUS server can authenticate the client, and (2) the entire exchange and communication ends up timing out -- thus forcing a manual re-connect. This is not a common occurrence by any means, but I just wanted to share what made us later choose to define only 1 RADIUS server, in the network settings. Surely our circumstance here is rather unique, but I thought it might be worth mentioning. Having only 1 RADIUS server defined forces ALL of our APs to use the same RADIUS server, regardless of anything else. It has resulted in a much smoother re-auth process for our clients.
I appreciate the link you sent, however. If I come across anything else that is helpful, I'll certainly post it back here. I appreciate your input once again! -
Issue in Sub-interface traffic on cisco 7609-s router
Hello please support,
I configured sub-interfaces and it is working properly, but some time sub-interface show traffic more then physical interface .
Like
int gi 3/32 0.13 Mbps 12:00 PM
int gi 3/32.11 855 Mbps 12:00 PM
as per my knowledge physical interface have cumulative traffic of all sub-interfaces.
interface GigabitEthernet3/32
no ip address
interface GigabitEthernet3/32.10
encapsulation dot1Q 10
ip address 172.20.128.77 255.255.255.252
ip ospf network point-to-point
ip ospf bfd
bfd interval 50 min_rx 50 multiplier 5
no bfd echo
no cdp enable
interface GigabitEthernet3/32.11
description interlink MPLS
encapsulation dot1Q 11
ip address 172.20.129.73 255.255.255.252
ip ospf network point-to-point
mpls ip
mpls label protocol ldp
Regards,
Damodar NagarI have not that graph so I am just guessing that you are noticing the difference between policing and shaping. It seems to me you are applying these techniques on each platform on a different way. Try to shape/police in the same order or only to shape.
Hope to help
Alessio
Sent from Cisco Technical Support iPad App -
Connectivity issues between Cisco 2901 and Cisco SG300-52
Hello,
I am having some serious connectivity issues between the hosts in my LAN.
My LAN is based on a Cisco 2901 router and a Cisco SG300-52 port switch.
The issue that has been happening is that connections between hosts on the LAN (remote desktop, extended ping, etc) is very unstable, at some point I can see a 35% lost packets on an extended ping. This happens at any time of the day and from any host.
All hosts are on the same Vlan(default Vlan) and on the same subnet. Some hosts have fixed IP addresses (servers and network equipment) and others obtain their IP address trough a DHCP reservation established on the router (reserved with the MAC address of every host).
I can provide further details if needed, because this issue is very serious and I would really appreciate any insight or support.
Many thanks in advanced.
Sair Amer
EDIT: After doing every test we could think of, we finally found the reason behind this problem.
It turns out that the switch has problems handling communications between clients at different speeds, because most of the hosts connected were working at 100 Mbps but the servers were working at 1000 Mbps (and the communication between host and servers wasn't stable).
After manually setting the speed on all ports to 100 Mbps the problems have stopped.
Many thanks for you help on this issue.Building configuration...
Current configuration : 4123 bytes
! Last configuration change at 12:06:16 PCTime Sat Jul 19 2014 by ccp
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Foninsa
boot-start-marker
boot-end-marker
no logging buffered
enable secret 5 $1$BDbJ$HN3VP8nmywrGB55RCxPd30
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone PCTime -4 0
clock summer-time PCTime date Apr 6 2003 2:00 Oct 12 2003 12:00
no ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.10
ip dhcp excluded-address 192.168.1.151 192.168.1.255
ip dhcp pool FONINSA
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 8.8.8.8 8.8.4.4
ip dhcp pool Laptop-Sporta-Wifi
host 192.168.1.10 255.255.255.0
ip name-server 8.8.8.8
ip name-server 8.8.4.4
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-213585710
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-213585710
revocation-check none
rsakeypair TP-self-signed-213585710
crypto pki certificate chain TP-self-signed-213585710
certificate self-signed 01
30820229 30820192
quit
license udi pid CISCO2901/K9 sn
license boot module c2900 technology-package securityk9
username ccp privilege 15 password
redundancy
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 190.196.21.98 255.255.255.248
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
no ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0 overload
ip nat inside source static tcp 192.168.1.3 21 190.196.21.98 21 extendable
ip nat inside source static tcp 192.168.1.3 80 190.196.21.98 80 extendable
ip nat inside source static udp 192.168.1.8 1194 190.196.21.98 1194 extendable
ip nat inside source static tcp 192.168.1.4 3389 190.196.21.98 3389 extendable
ip nat inside source static tcp 192.168.1.9 3389 190.196.21.98 10000 extendable
ip nat inside source static tcp 192.168.1.3 3389 190.196.21.98 20000 extendable
ip route 0.0.0.0 0.0.0.0 190.196.21.97
access-list 1 permit 192.168.1.0 0.0.0.255
control-plane
line con 0
password $
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 5
access-class 23 in
privilege level 15
password #
transport input telnet ssh
no scheduler allocate
end
Maybe you are looking for
-
Cp5 edit background in Photoshop not working
I'm trialling Cp5 and one of the key deciders is the Photoshop workflow. On my usual workstation I have Cp4 and the standalone version of Photoshop CS3 extended and the CTRL-U background edit just works. The workstation I'm trialling Cp5 on has the C
-
wat is context and how it changes?
-
What would cause all my texts between a certain person and myself only disappear into thin air?
How do I remove apps on my iPhone? I've done it before, but can't quite get the combination correct again!! - 4S - Thank you
-
AIR for iOS app crashes on launch - only on iPad1
Hello, Been working on an iPad book app in FlashBuilder 4.6. Early on there were some performance issues with iPad1/3 until learning about GPU rendermode and setting the StageQuality to low. These helped immensely. However, recently the app starting
-
Code Review:: ADF BC applications
Hi, We would like to know if there's any open source software available for code reviews of ADF applications and how to effectively use to for ADF BC applications? 1) Am I moving in right direction while exploring PMD and Checkstyle? Are these the ri