My client requirementis: same file name should be in target system

I am getting one file from source system the file name is empdetails.txt. I want to pass the same file name to the target system how we can implement this requirement.

The below blog will also useful
XI: The same filename from a sender to a receiver file adapter - SP14
you can also refer to SAP Note 821267 - FAQ: XI 3.0 / PI 7.0 / PI 7.1 / PI 7.3 File Adapter
regards,
Harish

Similar Messages

  • How to create Same file names for source and target.

    hi
    Can any body send Procedure for below requirement.
    how to create the dynamic file names for a source and save the file with same name in the Target, because it has to identify that which sender had sent the file and the target file should be again sent back to the customer as a link.
    Please help me.
    Thanks

    Hi,
    See the below link
    /people/michal.krawczyk2/blog/2005/11/10/xi-the-same-filename-from-a-sender-to-a-receiver-file-adapter--sp14 - sender file name as receiver file name
    Regards
    Chilla

  • Receiver file name should contain the same plant value as  sender filename

    Hi All,
    I have a requirement in PI 7.0 and the scenario is synchronous which is as follows:
    - XI will read a flat file which has the naming convention Plant_100.txt where 100 is the plant number , after reading the file XI will trigger standard BAPI call to ECC system.
    - ECC system will return an response message back to XI , XI need to need write this message in to a log file and the file name should be Plant_100_logs.txt.
    - Here plant value 100 is neither passed to ECC system nor this value will be returend back from ECC system . So , is there anyway where we can make sure that plant value can be added to the log file without using an BPM in between ??
    Regards
    Vinay P.

    Hi,
    Using Dynamic configuration in Message mapping you can read the source file name and creta the target file name as same as source file.
    For BAPI call in Mapping you can use RFC lookup.
    So crete a scenario FILE to log FILE
    In mapping using RFC lookup make a BAPI call.
    And use dynamic configuration to set the file name.
    Refer this
    http://www.****************/Tips/XI/ASMA/Index.htm

  • Source and target directory file name should be same

    Hi,
    How can i generate the same file name in target directory without date and Timestamp.
    for eg., Source File name : yeswanth.txt
    and target File name also : yeswanth.txt
    Note : here source side the file yeswanth.txt is constant and whenever it moves to target directory...should be overwrite.
    Reward points for useful answers.
    Thanks & Regards,
    yeswanth.

    Hi Mugdhal,
    am getting this error when i sent the same file again.
    Message processing failed. Cause: com.sap.aii.af.ra.ms.api.RecoverableException:
    Yeswanth.txt: Cannot create a file when that file already exists. : com.sap.aii.adapter.file.ftp.FTPEx: 550
    Yeswanth.txt: Cannot create a file when that file already exists.
    But, here it should be overwrite the existing file.
    Regards,
    Yeswanth.

  • SFTP to Mail with attachment as same file name from sender side

    Hi All,
            I am Using a SFTP to Mail scenario, I have a requirement in which an Sftp adapter after picking up a file should have an attachment with same file name to the Receiver Mail Adapter.
    Can anyone help me out?
    Thanks in Advance
    Edited by: uday kumar on Feb 15, 2009 2:00 PM
    Edited by: uday kumar on Feb 15, 2009 2:02 PM

    Hi,
    Find below link will helpful for configuration, but as per my knowledge file name at attachment will take as message id.  Check it with below link, i hope it will work
    /people/prasad.ulagappan2/blog/2005/06/07/mail-adapter-scenarios-150-sap-exchange-infrastructure

  • How to create Same File Name in Recever side

    Hi Frnds,
    1)In my sender side i am having one XML file Name:  vendor123.xml
    i have to send this file to receiver side with same file name, what are setting i need to do in file adapter.
    In receiver side i dont have any file, i have to crete with same file name.
    2)
    In my scenario my message interface name Vendor123_mt.
    In receiver side my file name should be Vendor123_mt, How to do handle this situation.
    Regards,
    Raja Sekhar

    Hi Raja,
    Regarding you 1st question: It can be easily achieved using the Adapter specific Message Attributes. You can refer the Michal's blog for it.
    /people/michal.krawczyk2/blog/2005/11/10/xi-the-same-filename-from-a-sender-to-a-receiver-file-adapter--sp14
    Regarding your 2nd question:
    Here you will need to use Variable Substitution. Use the following link:
    http://help.sap.com/saphelp_nw70/helpdata/EN/ae/d03341771b4c0de10000000a1550b0/frameset.htm
    Hope it helps.
    Regards,
    Sanjeev.

  • Send port with same file name as receive

    I have a filename "abc.docx". I need to create a send port where I should set the file name in a such a way that I should have the same file name as received.
    I have set the filename in the send port as "%SourceFileName%" but it does not seem to be working.
    How to set the send port to have the same file name as received by the receive port? Send location should hold the same file name

    could you please also mention what is happening when you set
    %SourceFileName% .  what kind of output filename are you getting then when used %SourceFileName%
    ?  incase if you are not getting any file at all in the output, then its not the issue with %SourceFileName%
     macro.
    Please mark the post as answer if this answers your question. If this post is helpful, please vote as helpful by clicking the upward arrow mark next to my reply.

  • Downloads with same file name override each other

    This happens with large files and/or slow connection.
    - The default limit is loading 2 files at a time.
    - Suppose the user is currently loading A.txt and B.txt
    - While loading, user also clicks http://url1/C.txt and http://url2/C.txt (different URL but same name), and they are added to the queue.
    - Firefox loads both of them into a single file, they should be separated instead (C.txt and C-1.txt)

    Celtic Mom
    Welcome to the Apple user to user discussion forums
    While I was organizing my photos, I realized there are about 30 or so photos that have the same exact file name as another photo. Example: There are two IMG_1243.jpg, but they are different pictures. They were taken at different times, even different years. I have used more than one camera to import photos. I have changed the name of one of the photos in the Title area in the information section of iPhoto. When I try to put the newly named photo into a folder that has the other IMG_1243, I get a message that says" An older item named "IMG_1243" already exists. Do you want to replace it with the newer one you are moving?"
    I want to have both IMG_1243.jpg photos in the same folder. How can I do this? Also, I have a few thousand pictures, so how can I tell exactly how many photos have the same file name as another photo?
    It sounds like you are using the finder inside the iPhoto library - do not do that - you will corrupt your library and lose the edits, keywords, etc that you have
    iPhoto does not care about duplicate file names - it handles it fine
    changing the title of a photo does not affect the file name - although when you export the photo you can use the title for the file name as an option
    What are you doing and what do you want to accomplish?
    Remember do not ever make any changes in the iPhoto library using the finder or any other program
    LN

  • When saving a File OS Is Creating Multiple Folders With The Same File Name

    Not sure what I changed but, now when I save a any file (ppt. word, Keynote,Pages e.g.,) to the desktop or any other location the OS will also create multiple file folders with the same file name as the file I'm saving. Inside the folders are what appears to be files locating the saved files. What can I do to fix this problem?
    I'm using the 10.7.2 version
    MacBook Pro

    Misio wrote:
    It looks like a finder bug. To replicate, I surf to any website, I right-click on a jpg image, select "Save Image As" and in the window that pops up I type in the filename "000.jpg", I select the folder Pictures, and click on Save.
    BTW, I don't know why, but the file was saved only as "000" without the file extension ".jpg". Does anybody know why?
    the extension is simply hidden. go to the get info panel for the file and uncheck the option to hide the extension.
    Then I surf to another image, and again I save it as "000.jpg" and now it asks me if I want to replace the existing filename, although the existing one is "000" and I try to save as "000.jpg", so I say yes, and then magically the file is saved with the full filename including the extension "000.jpg"
    When I did it a couple of times, always saving image as "000.jpg" from various sources, I ended up with two distinct files named "000" and both in the same folder Pictures.
    Please advise.
    it sounds to me like you saved one file as 000.jpg and the other and 000.jpg.jpg.
    check the info panels for the files for full names to verify if this is the case.

  • I can not transfer date from one hard drive to another, I keep getting an error because I have two of the same file names and one file name is in caps and I cant change the file name

    can not transfer date from one hard drive to another, I keep getting an error because I have two of the same file names and one file name is in caps and I cant change the file name. My original external has an error and needs to be reformatted but I dont want to lose this informations its my entire Itunes library.

    Sounds like the source drive is formatted as case sensitive and the destination drive is not. The preferred format for OS X is case insensitive unless there is a compelling reason to go case sensitive.
    Why can't you change the filename? Is it because the source drive is having problems?  If so is this happening with only one or two or a few files? If so the best thing would be to copy those over individually and then rename them on the destination drive.
    If it is more then you can do manually and you can't change the name on the source you will have to reformat the destination as case sensitive.
    Btw this group is for discussion of the Support Communities itself, you;d do better posting to Lion group. I'll see if a host will move it.

  • I worked with files in LR that were originally on my C drive, then were moved to an external HD for storage. I now want to do some more work on those files (which have the same file name as on the C drive). I plugged the drive into my computer and it show

    I worked with files in LR that were originally on my C drive, then were moved to an external HD for storage. I now want to do some more work on those files (which have the same file name as on the C drive). I plugged the drive into my computer and it shows in LR under folders as the F drive and the little green light is on, but LR is showing only the first 6 files and not the remaining 200 or so. How do I expand the F folder to expose all files?

    I worked with files in LR that were originally on my C drive, then were moved to an external HD for storage. I now want to do some more work on those files (which have the same file name as on the C drive). I plugged the drive into my computer and it shows in LR under folders as the F drive and the little green light is on, but LR is showing only the first 6 files and not the remaining 200 or so. How do I expand the F folder to expose all files?

  • File name should change by selecting the radio buttons

    Hi all,
    PARAMETERs: p_file LIKE rlgrap-filename.
    PARAMETERS: p_app RADIOBUTTON GROUP rg DEFAULT 'X',
                             p_pre RADIOBUTTON GROUP rg.
    this is to download the ITAB data to presentation and application servers depending upon the radio button selected.
    if i select p_pre , then default download path is : 'C:/ download.txt'.
    if i select P_app , default download path is : '\usr\sap\EBG\SYS\profile\DOWN.TXT'.
    how the file name should change by selecting the radio buttons ?
    Thanks
    KR

    Hi,
    DATA: c_x VALUE 'X'.
    selection-screen begin of block input with frame title text-000.
    parameters :desktop     radiobutton group rg_f user-command rg_f,
                       in_file type ibipparms-path modif id ps DEFAULT 'C:/ download.txt',
                menu     radiobutton group rg_f ,
                       sys_file type ibipparms-path modif id as default  '\usr\sap\EBG\SYS\profile\DOWN.TXT' .
    selection-screen end of block input.
    at selection-screen output.
      if desktop is initial and menu is initial.
        desktop = c_x.
      endif.
      perform f_toggle_finputs.
    form f_toggle_finputs.
    loop at screen.
        if screen-group1 = 'PS'.
          if desktop = c_x.
            screen-input    = 1.
    *         sys_file = c_server_path.
          else.
            screen-input    = 0.
          endif.
        endif.
        if screen-group1 = 'AS'.
          if menu = c_x.
            screen-input    = 1.
    *        clear: in_file.
          else.
            screen-input    = 0.
          endif.
        endif.
        modify screen.
      endloop.
    endform. "f_toggle_finputs
    Hope this helps u.
    Thanks.

  • Same file name in target as source file

    Hi,
    I am doing a file to file scenario in which there is no mapping involved, it is a bypass scenario.
    I want my target file name to be exactly same as the source file name.
    Source file name dynamically changes based on date and time.
    I have tried creating the target file using the Add timestamp characteristic. But it is not in the same format as the source file.
    How can I achieve this???
    Since there is no mapping invlolved, I can't use dynamic configuration or variable substitution.
    Please advice.
    Regards,
    Sachi

    Hi Sachi,
    -->Are you bypassing the mapping rite....?
    -->Then in your ID under Interface determanation what interface mapping did you maintained....?
    -->I think you are by passing the IR.
    -->I think this can be achived by using the ASMA but it requires the Mapping Program.
    -->Even the above blog explains about getting the same file name using the ASMA and UDF.
    Thanks

  • Different photos with the same file name!! How to change this?

    While I was organizing my photos, I realized there are about 30 or so photos that have the same exact file name as another photo. Example: There are two IMG_1243.jpg, but they are different pictures. They were taken at different times, even different years. I have used more than one camera to import photos. I have changed the name of one of the photos in the Title area in the information section of iPhoto. When I try to put the newly named photo into a folder that has the other IMG_1243, I get a message that says" An older item named "IMG_1243" already exists. Do you want to replace it with the newer one you are moving?"
    I want to have both IMG_1243.jpg photos in the same folder. How can I do this? Also, I have a few thousand pictures, so how can I tell exactly how many photos have the same file name as another photo?

    Celtic Mom
    Welcome to the Apple user to user discussion forums
    While I was organizing my photos, I realized there are about 30 or so photos that have the same exact file name as another photo. Example: There are two IMG_1243.jpg, but they are different pictures. They were taken at different times, even different years. I have used more than one camera to import photos. I have changed the name of one of the photos in the Title area in the information section of iPhoto. When I try to put the newly named photo into a folder that has the other IMG_1243, I get a message that says" An older item named "IMG_1243" already exists. Do you want to replace it with the newer one you are moving?"
    I want to have both IMG_1243.jpg photos in the same folder. How can I do this? Also, I have a few thousand pictures, so how can I tell exactly how many photos have the same file name as another photo?
    It sounds like you are using the finder inside the iPhoto library - do not do that - you will corrupt your library and lose the edits, keywords, etc that you have
    iPhoto does not care about duplicate file names - it handles it fine
    changing the title of a photo does not affect the file name - although when you export the photo you can use the title for the file name as an option
    What are you doing and what do you want to accomplish?
    Remember do not ever make any changes in the iPhoto library using the finder or any other program
    LN

  • Same file name from sender to receiver file adapter with out using UDF

    Hi All,
    I am working on FILE TO FILE. My requirement is same file name from sender to receiver file adapter. Is it possible to do using only Adapter Specific message properties?  i mean with out using UDF.
    Thanks
    Karthik

    Hi,
    >>>Is it possible to do using only Adapter Specific message properties?
    yes
    just enable Adapter Specific message properties in sender and receiver channel for file name
    and you're done
    Regards,
    Michal Krawczyk

Maybe you are looking for