My iMac 27 became incredibly slow... And often the spinning wheel makes me wait ages even for simple actions (like switching desktops or just clicking the Apple logo)... What can I do ?
After a crash of one of my partitions, I reinstalled my system on another (Lion).
I've made all the updates but now everything is incredibly slow. It takes ages to have an answer (like "About this Mac" or to launch any software or utility.
I have check th hard disk and apparently, the partition is correct.
What can I do to find where is the problem ?
Tanks for the advice
Infortune télé, i cannot use thé recouvert partition bécasse I don't havé any... i havé to say I havé bruit à spécial environnement : at first I was usine Snow Leopard... And I built a Boot Camp partition... When I bought my Lion, I estimated it could be dangerous to jump straightforward to Liom, so I created a third partition for Lion and I installed it... But this was not compatible with the recovery partition !
So, when my first Lion partition crashed (I got bad block on the volume) I decided to suppress the boot camp volume qns to reinstall Lion. Fortunately, Snow was still running.
I.ve done all the other things you've adviced and things are going better... Everything works except mail : I guess I have to suppress all the mail account, repair the disk (and permission) and reconnect the mail accounts !
Cheers
Similar Messages
-
my ipod touch get restart by itself, and just get stuck with the apple logo, What can i do?
Try connecting it to your iTunes library in recovery mode using the instructions in this Apple support document.
http://support.apple.com/kb/ht1808
Otherwise, try connecting in DFU mode.
http://www.iclarified.com/entry/index.php?enid=1034
B-rock -
TS3680 i cant start my imac computer... im stuck at the apple logo?
i cant start my imac computer... im stuck at the apple logo?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
i have erased my all phone contact list and then the message comes that it will be deleted with in an hour. but now my phone is not starting and only the apple logo appears on the screen. what should i do now..!
That number is for an apple server in the UK that is used for iMessage activation. A hidden SMS is snet to that number when you turn iMessage on and is used to verify your phone number. I suggest you turn iMessage off. In settings/phone turn on dial assist. Check with your carrier to see if you can send an international SMS as you end that possibility to activate iMessage. Rest your phone (Hold down the Sleep/Wake button and the home button together until the apple logo appears (ignore the ON/OFF slider) then let both buttons go and wait for device to restart (no data will be lost).) then turn iMessage back on.
-
Mac pro running OS 10.5.8 won't boot. Apple logo and spinning wheel shows then Apple logo turns into Forbidden signage while spinning wheel continue. It happenened right after I installed a firmware. Had to restart.Please help. What can I do?
Work through the suggestions in this article:
Mac OS X: Gray screen appears during startup -
My iphone 4 randmonly started going into recoveery mode when i was trying to download ios 7.1, and now the apple logo will come one and then fade to black and continue this process. My iphone wont restore either and will get the 3194 error message.Help please!
Hello chindeepchow,
Thank you for using Apple Support Communities.
For more information, take a look at:
Resolve specific iTunes update and restore errors
http://support.apple.com/kb/ts3694#3000
Resolve communication issues
Related errors: 17, 1004, 1013, 1638, 3014, 3194, 3000, 3002, 3004, 3013, 3014, 3015, 3194, or 3200. These alerts refer to gs.apple.com, say "There was a problem downloading the software," or say the "device isn't eligible for the requested build."
Check the hosts file or TCP/IP filtering, which might cause communication issues between iTunes, ports, and servers.
Have a nice day,
Mario -
My iphone 6plus not working not charge but when i run it the first time working half an hour when you attempt to run it again light up thr screen and showws the apple logo and after the pice screen illuminates red and does not work what do i do now
Hello Nadersalah,
It seems you're experiencing multiple issue with your iPhone. Based on the information you have provided, it appears your iPhone needs to be serviced. The following link should help you get started with the process and has links with additional information on topics such as warranty and service pricing, battery replacement, and express replacement service.
iPhone Repair and Service - Apple Support
Thank you for contributing to Apple Support Communities.
Cheers,
Bobby_D -
Have an iPod touch 4th gen. It is completely charged, but once I disconnect from a power source it shuts down and then the apple logo just keeps reappearing. I have restored via iTunes and reset all the settings. Any suggestions?
If you restored to factory settings/new iPod via iTunes (Not via Settings>General>Reset>Erase all Content and Setting) and still have the problem that indicates a hardware problem.
Make an appointment at the Genius Bar of an Apple store..
Apple Retail Store - Genius Bar -
iPad went black and has the apple logo with a little wheel at the bottom. Tried turning on and off doesn't work.
Try a Reset...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430
If no joy...
Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414 -
My iPad mini keeps turning itself off and then the apple logo keeps flashing constantly, i have charged it fully and restored it many times. what can i do?
If you have restored to factory settings and started as new, there is nothing more that you can do on your own. Make an appointment at an Apple Store and ask them for help. You might have a hardware problem and the Apple Store techs will be able to determine that.
-
I have a iPad 3 (wifi+cellular). Today I updated with the latest software update. But after the installation of the update it doesn't start. Again and again the apple logo flashes and nothing happens. I tried to reset it by accessing it through iTune. But it is not recognized by iTune. Please help.
Hello bhar.suman,
Thank you for using Apple Support Communities.
For more information, take a look at:
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
Have a nice day,
Mario -
My iphone wont turn on, it keeps loading for the longest time and then the apple logo appears for about 10 seconds and then glitches to the color blue and repeats.What do i do?
Hi there e12345,
You may find the troubleshooting steps in the article below helpful.
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
-Griff W. -
I was resetting my iPhone 4 and then the Apple logo came up and a a bar under it, then it got stuck. Please help
Hi
I have done lots of reading on th einternet ref this, i have now got as far as the Safe mode reboot, Boot the Iphone up in Safe mode, but now iTunes ask if i want to restore the iphone back to factory setting, which i want to do Please!!!!
as soon as it starts it then checks for any new software for the phone, at this stage it others me the new os5 software, but it drops out saying error 3194 again, it just keeps going around in a loop. -
I was restore my i phone 4 and then the apple logo is still no action
i was restore my i phone 4 and then the apple logo is still no action so what can i do in this matter ?????????????/
Hi
I have done lots of reading on th einternet ref this, i have now got as far as the Safe mode reboot, Boot the Iphone up in Safe mode, but now iTunes ask if i want to restore the iphone back to factory setting, which i want to do Please!!!!
as soon as it starts it then checks for any new software for the phone, at this stage it others me the new os5 software, but it drops out saying error 3194 again, it just keeps going around in a loop. -
During the last week my Iphone has been switching off/on on its own and now my Iphone got stuck at the apple logo.What should I do?A month ago it also happened but then everything got back to normal.A person told me to change th display...what should i do?please help!
Hey adinat,
Welcome to Apple Support Communities! I would go through the steps in the iPhone troubleshooting assistant and see if that resolves the issue you're experiencing on your iPhone 5:
Frozen or unresponsive iPhone
http://www.apple.com/support/iphone/assistant/phone/
Regards,
David
Maybe you are looking for
-
Access to DFS root via VPN not working - error 0x80070035 keeps popping up
Dear all, when trying to access the DFS root via VPN from a Windows 7 non-domain member computer I always receive an error stating "Windows cannot access \\eggs.local\dfs", Error Code: 0x80070035, The Network Path was not found. I searched the intern
-
Hello Expert, In CA03 Transaction Code, there are fields like Operating ,workcenter, plant , control Key, Activity Type etc.. I just want to know where these all customization can be done want to check cost center and activity hours for one article.
-
Report to see list of ROUGH GRs
Rough GR is created, changed and displayed by Tcodes VL41, VL42, VL43 respectively. But how do I see a list of Rough GRs that are created?? Any report or any other way to see the list of Rough GRs?
-
JDBC Sender Adapter to Oracle Server
Hi Friends, Iam using JDBC Sender Adapter to connect to Oracle Server. I have mentioned all the parameters in the Configuration(sender communication channel) correctly.My Adapter Monitoring in RWB shows a message that "Processing finished successfull
-
Automatically update 2 dimensional array based on list content
Suppose I have a simple class named SimplePoint class SimplePoint public int x { get; set; } public int y { get; set; } Next I create an ObservableCollection of the class and bind it to a WPF DataGrid via XAML. Each SimplePoint has a distance to each