My itouch will only display a white screen, is this fixable? help!

My i touch was working absoluty normally, then one day it would only display a white screen. I can still see it on my computer however it is showing that the memory has been wiped. I tried to restore it to its original settings, but it still displays the same white screen. I have drained the battery fully, and tried holding the buttons down for 10 seconds. Nothing is working and im now confused. Can anyone advise me please? thank you.

When restoring an iPod to factory defaults/new iPOd does not solve a proble it is most likely due to a hardware problem.  I would make an appointment a the Genius Bar of an Apple store.

Similar Messages

  • My ihone only displays a white screen and I want to fix it myself.

    my iphone will only display a white screen can I fix it and how can I?

    At this point, you probably be better off saving up for and purchasing a new one. Apple will not help you since you opened the iPod up.  A third party repair company may be able to help but the cost will likely be near the cost of buying a new Nano.
    B-rock

  • My iMacG5 will only boot to white screen, gray apple and spinning gear. Help?

    My iMacG5 will only boot to white screen, gray apple and spinning gear. Help?
    Also not totally sure if it's an Intel based computer, but that's what I recall. Any way to check, since I can't get to About This Mac window?
    It's running on OSX Leopard 10.5.4
    First symptom = running slowly - then it kind of froze with color wheel spinning - thought a forced shut down would help - help power button til off, then white screen, gray apple and spinning gear.
    Have tried...
    1. Turn off the computer by choosing Shut Down from the Apple menu, or by holding the power button until the computer turns off.
    2. Unplug all cables from the computer, including the power cord.
    3. Wait 10 seconds.
    4. Plug in the power cord while simultaneously pressing and holding the power button on the back of the computer.
    5. Let go of the power button.
    6. Press the power button once more to start up your iMac.
    Then try booting from your install disc again.
    - No change
    And...
    Booting From An OS X Installer Disc
      1. Insert OS X Installer Disc into the optical drive.
      2. Restart the computer.
      3. Immediately after the chime press and hold down the "C" key.
      4. Release the key when the spinning gear below the dark gray Apple logo
          appears.
      5. Wait for installer to finish loading.
    - The fan just got louder.
    Thanks for your help.

    You need to do an Erase and Install or an Archive and Install depending on whether the hard drive is OK or needs to be reformatted.
    Start by booting from your Leopard DVD. The rest is just following directions.
    How to Perform an Archive and Install
    An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
    1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
    Repairing the Hard Drive and Permissions
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
    3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
    4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
    5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
    6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

  • TS1424 when i open itunes store i will only see a white screen

    when i open itunes store i will only see a white screen and i can't see anything
    please someone help me

    Close your iTunes,
    Go to command Prompt -
    (Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
    (Win XP SP2 n above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
    In the "Command Prompt" screen, type in
    netsh winsock reset
    Hit "ENTER" key
    Restart your computer.
    If you do get a prompt after restart windows to remap LSP, just click NO.
    Now launch your iTunes and see if it is working now.
    If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
    Apple software on Windows: May see performance issues and blank iTunes Store
    http://support.apple.com/kb/TS4123?viewlocale=en_US

  • Blu Ray video disk will only display on W500 screen, not on attached screens

    My W500 (Win7-64bit) plays blu-ray disks perfectly on the W500's screen.   But it will not play on an attached 1600 x 1200 DVI monitor, either attached through a mini-dock, or via the DisplayPort and a DVI convertor adapter. In both those cases, WinDVD 2010 (which I purchased to replace WinDVD 8 provided) says "Your display environment does not support protected content playback"  WinDVD 8 gives exactly the same message. The same Blu Ray drive plays DVD's perfectly to the 1600x1200 DVI screen. Anyone understand what the problem might be ?  

    Hello,
    I saw your reply in this five year old thread asking about HDCP.
    HDCP is short for High Definition Copy Protection.  It means the devices at both ends (video card, monitor) must support encrypting the signal between them in order to prevent digital copying/piracy.
    Regards,
    Aryeh Goretsky
     

  • QT Uncompressed files display with White Screen

    I'm stumped.
    I have a few QT files that are uncompressed 8 bit. On my new 8 Core Intel Mac, a G5, and a Mac Mini I can see this file just fine. We're running 10.4.9 and QT 7.1.6. The Mac Minis and G5 are bare bones and have no codecs listed in the Library/Quicktime folder except Apple Intermediate (default).
    On all of my Intel XServes however, with the exact same installed universal binary QT codecs as my 8 Core, these same QT uncompressed files only display a white screen. In get info the codec is listed as Uncompressed 8bit 4:2:2. Last time I checked Uncompressed didn't even require a codec.
    Any ideas why the XServes can't read these QTs? I've even updated the QT to 7.2 hoping there was an Intel bug, but that didn't fix this.
    Thanks!

    There is no single codec for movies that have .avi extensions. AVI is a container format, not a specific type of file. An AVI movie may use one of the Indeo codecs (there are at least four that I'm aware of, none of which have been ported to Mac OS X) or one of the various flavors of DivX, among other possibilities. You'll have to find out what codec was used for the movies you want to view to determine what you need. Note that not all codecs for the various .avi movies are available for QuickTime.
    If you want to try "hit and miss", you can try the codecs at http://www.divx.com/ and http://www.3ivx.com/ and see if one of them will work for you. You can also give this player a try:
    http://www.videolan.org/vlc/
    Forum Tip: Since you're new here, you've probably not discovered the Search feature available on every Discussions page, but next time, it might save you time (and everyone else from having to answer the same question multiple times) if you search a couple of ways for a topic before you post a question.
    Regards.

  • After installing my Mac only shows a white screen. Help

    I updated and now when it restarted it will only give a white screen.

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
    a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.  
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • Mac will not boot up, white screen with turning gear for hours on end

    mac will not boot up, white screen with turning gear for hours on end

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.   
    There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
         a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
    b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a boot failure can be resolved by resetting the NVRAM.
    Step 4
    If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
    Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
    If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
    If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
    Step 9
    Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 10
    Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
    Step 11
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 12
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • Satellite A300 PSAG0A - Games Will Not Display in Full Screen Size

    I have a large number of games installed on my computer. At least 90% of them will not display in full screen size but display in a small window with a large amount of black screen surrounding the window. I am running Windows Vista Home Premium 32 bit. However, I do not think it has anything to do with Windows as my husband runs the same games on his Toshiba Satellite L300, running exactly the same version of windows, and they all display in full screen size.
    Altering the screen resolution makes no difference. And, of course, I do select the full screen option in the games.
    Also, sometimes when I have been playing a game and then closed it I find that my desktop picture has shrunk to the smaller size - the same size as the window in which the game was displayed when I was playing it.
    The games work fine in every other way, it is only this small screen size which is driving me nuts.
    I hope that someone can help me with this!!

    Yes, as far as I can tell I have the latest driver. But, even this is confusing to me because....
    My graphics media accelerator is Mobile Intel(R) 965 Express Chipset Family. The installed driver version is 7.14.10.1329. The release date for this is 2007-09-13, as far as I can tell from web searches.
    However, on the Toshiba website for driver downloads, the available driver version is 8.2.0.1012 PV. The date is 2006-12-28. I have downloaded this driver and attempted to install it. I get the message that it has been installed but, after rebooting and checking the installed driver version is still 7.14.10.1329.
    Perhaps, the 8.2.0.1012 PV version does not actually install because it is older than the currently installed version. I would have thought that the driver version with the higher number would be the newer one, but perhaps this is not the case as the dates do not seem to support this theory.
    So now I ask myself, firstly, if the driver available for download on the Toshiba website is not the newest one, then why is it there?
    Secondly, if it is the newest one then why will it not install on my computer?

  • HT204291 Using Azul media player app on my ipad  Apple tv will only display sound but not video from movies.  Any ideas on a fix.  I set mirroring to on but it still does not display video.  It will display photos and video recorded from my iphone.

    Using Azul media player app on my ipad  Apple tv will only display sound but not video from movies.  Any ideas on a fix.  I set mirroring to on but it still does not display video.  It will display photos and video recorded from my iphone.

    Here are the steps for AirPlay:
    Before starting Azul from your (running iOS 5.x/6.x) home screen where have have all your apps we need to turn on mirroring
    On your iPhone 4S/5 or iPad 2 or 3, double-click the Home  Button to view your recently-used apps.
    Swipe all the way to the right to until you see the  icon.
    Note: If the icon does not appear, go to the "If AirPlay Mirroring is not visible or available on your mobile iOS device" section.
    Tap the  icon to see the list of available AirPlay devices.
    Enable AirPlay Mirroring in this menu by tapping on an available Apple TV, then sliding the Mirroring slider to ON.
    Now you should be seeing your iPad/iPhone on your TV.
    Start up Azul now and using the settings icon on the top right corner go to the option that say "TV out" ON.
    When you do that you will see an Orange screen
    Now click "Done" and play the video you want to watch and it will AirPlay

  • My MacBook pro won't recognize hard drive I put in it. It boots only to a white screen unless I boot to my recovery USB. If I do that then I can select my USB and my external time machine drive in the disk utility, so no problems there. But what do you

    My MacBook pro won't recognize hard drive I put in it. It boots only to a white screen unless I boot to my recovery USB. If I do that then I can select my USB and my external time machine drive in the disk utility, so no problems there. But what do you think it is? It won't recognize any hard drive I put in the machine, so might it be the sata cable?

    Boot the Recvoery USB, use Disk Utility to select the internal drive makers namea and size on the left.
    Now select erase and select the midde option and click erase, it will take a bit to complete but it's best for the drive.
    Now select Partiton tab, click the big box and Options: GUID and then Format: OS X Extended journaled and click apply.
    Quit and you should be able to install OS X now with your Apple ID and password.
    see
    http://osxdaily.com/2011/08/08/lion-recovery-disk-assistant-tool-makes-external- lion-boot-recovery-drives/

  • Firefox 13 only displays a white box instead of an image on certain websites

    Firefox 13 is only displaying a white box where the picture should be. This is happening on different websites, but I will include a link to the latest one for me. Internet Explorer displays the image just fine:
    http://www.bostonproper.com/product/Asymmetrical-hem-maxi-dress/836602/sc/169/c/169/pc/44.uts
    You should see a large image of a woman in a red dress on the page, not a white box. I have tried clearing the cookies and cache, I have the settings to allow images from this website and nothing is working. The trouble seems to have started when I updated to Firefox 13.

    I completed the steps in the article and disabled the Real Player plug in. That did the trick and Firefox 13 is now displaying the images correctly. I am wondering if these issues will be fixed in the future because I do use Real Player quite a bit. Thank you so much for the help!

  • When i turn in my computer it only come a white screen whit a map and a questionmark?

    When i turn in my computer it only come a white screen whit a map and a questionmark?

    That folder with the question mark icon means that the MacBook can't find the boot directory. That can either mean it can't find the hard drive or the Operating System data on the hard drive is somehow corrupted.
    Put your install DVD into the optical drive and reboot. As soon as you hear the boot chime, hold down the "c" key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
    When it does start up, you'll see a panel asking you to choose your language. Just press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it. When it comes up is your Hard Drive in the list on the left?
    If it is then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've clicked on the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions.
    If your hard drive isn’t recognized in Disk Utility then your hard drive is probably dead.

  • Tried updating my itouch, now I have a white screen. What do I do?

    Tried updating my itouch, now I have a white screen.  I tried plugging it into my computer to update via itunes, but itunes will not recognize that the device is plugged in.  What do I do?

    You will likely have to let the battery fully drain
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • Firefox will not display on the screen even though with Process Explorer I see Firefox.exe active but no CPU usage

    I use Firefox v10.0.2 as default browser on Dell XPS8300 e/w Intel Core i5 & Windows 7 Ultimate and Compaq Presario CQ57 e/w Intel Core i3 & Windows 7 Home. More frequently on the (about 90% of attempts) than the Dell (50% of attempts) Firefox will not display to the screen when I click on icon. When it happens I cannot display other programs. I specifically say display because I believe Firefox has started. To circumvent the problem I installed Process Explorer on both machines and start this program first then click on Firefox icon. When problem occurs I can see Firefox.exe process in Process list; some CPU consumed but, then, no CPU activity. If I click on Firefox icon again another process opens in Process list but with same response - some CPU consumed and then no CPU activity. If I have 2 processes running and kill the 1st process, the 2nd will display and everything from then on is normal. If I do not open a 2nd process but kill the 1st process then click on Firefox icon Firefox is displayed and everything from then on is normal. This problem has occurred since original installation on both new machines. I've updated video drivers in both machines.

    Ok, let's see if we can fix this and get it working for you!
    First, if you start Firefox in [[safe mode|safe mode]] (restart your computer first, then when you open Firefox, hold down the shift key) does it start up more reliably? This is usually caused by a faulty add-on. If it does help, then restart Firefox, go into the Firefox button, then add-ons, and disable your extensions one by one until you find the trouble maker.
    Also, try updating to Firefox 11, it has several bug fixes that might make life easier here.
    Just as a few basic troubleshooting steps to make sure we have all the bases covered,
    Run all Windows Updates, install all needed service packs, etc.
    Update all your plugins (Flash, Java, etc.): [http://www.mozilla.org/plugincheck/ http://www.mozilla.org/plugincheck/].
    Download and Install MalwareBytes Anti-Malware, run a full Scan. [http://www.malwarebytes.org/ http://www.malwarebytes.org/]. This helps check that there are no viruses on your computer causing issues. you can uninstall this program after you clean off any infections.

Maybe you are looking for