My storm 9530 is showing a red light ..HELP ME PLEASE !!!

My storm 9530 is showing a red light about 7 seconds and cuts off i am not even seeing anything like a missing battery or the blackberry reboot on the screen.after. when i connect it to my PC it dose the same thing but i keeps doing it over and over.

I'm sorry, but I don't think I fully understand what you said there. And I did use the word "accidental"...I did not mean to imply any intentional damage done by anyone.
Are you saying that the original problem you reported (not being able to boot up) existed before you had any work done on the device? If so, then that actually complicates matters even more -- having changed out so much of the internals of the device may have, as I say, damaged something further. Or, it is also possible that the parts you replaced caused no additional damage and are functioning fine -- but they simply did not include whatever it was that was originally damaged/failed.
I also do not understand what you say about "did just that"...I cannot tell if that means you did the battery swap as I recommended, nor what the specific results were if indeed you conducted that test. For example, specific results from a battery swap could include:
Both devices work fine with either battery
The original device still does not work with the other battery, but the other device works fine with the battery from the original
The original device works fine with the other battery, but the other device does not work with the battery from the original
Etc, etc. etc...there are several variations of possible results, and the specific result from each device using the other battery is what provides the clearest indication of if the battery is causal or not. But, from your words, I do not understand your specific results...I'm sorry that I'm not understanding you.
Nevertheless, if your battery swap test result is as described in item 2 above, then that indicates a hardware problem with the device itself. And again, at an internet distance, hardware issues are nearly impossible to diagnose -- nothing can replace in-hand evaluation by a qualified technician.
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

My blackberry curve 8520 is not turning on it shows a red light

My blackberry curve 8520 will not turn on it shows a red light flashes 2x then my keypad lights an thats it nuthing else happens please help me i havent got a usb cable so cant use blackberry desktop manager

Hello Hasanm52,
Welcome to the community!
Seems OS is corrupt, so you have to arrange a USB cable to connect your devci with the pc.
Procedure to install OS:
1.) Download and install blackberry device software of Blackberry 8520 from www.blackberry.com.
2.) Install it in your PC & connect your device with PC.
3.) Access path c:\prog. files\Common files\ Reasearch in motion\ App loader\ now dowble click on loader.exe
4.) Further procedure i very user friendly, so please follow steps (may take approx 90 mins).
5.) In between, it will prompt you to take backup as well, so do take care while clik next or continue.
Good luck..!!!
Before doing above activity you may try
By pulling out battery & connect device with charger without inserting battery & wait for 5 to 10 mins.
Itwill prompt you a no battery sign on your handheld, once you get the sign on your handheld, insert battery without un plugging charger 7 wait for another 5 to 10 mins. Hope this will work for you....
otherwise you have to perform the first procedure, i mentioned...
Thanks....!!

KT6 Delta All Four Red Lights Help

I just purchased a kt6 delta and I am trying to get it going. I am upgrading from a KG6-RAID. I moved everything over, and got ready to try it out, and when I turned it on I get all 4 red lights. Then I tried the parts on the old Mobo and things boot up.
I removed everything, so all I have is 1 ram stick, the processor, and a video card. Here is what I have in there.
kt6 Delta
xp 1700
Name brand hsf (forget what it is, but its certified for xp1700).
256 meg Crucial 2100
Leadtek ti4200 card
Antec pp-303x psu ( http://www.antec-inc.com/specs/p303x_spe.html ) . Psu has been in use for less then 3 months.
Please let me know if you have any ideas. Thank you.

I think I am reading this correctly.
+5v - 7-30a
+12v - 1-10a
+3.3v - .5-14a
I have tried it with no memory, and with a Centron (generic) stick. Both 2100. Both check out on other motherboards.
I have artic silver between the heatsink and processor.
I'm thinking if anything it could be the power supply, but I don't know.

D-LED showing 4 red lights

Just got my MSI board back from MSI. Tried to boot up and it hangs. I get the 4 red led lights suggesting processor installed wrong or damaged. I found i had a little bit of Silver3 on one of the pins. But i cleaned it up good. And it still hangs on me. Did i damage it you think? I called intel about it and they took my phone number and there suppose to get back to me. They left a message today saying they will call back and ask for mobo info and bios and all.
Thanks

While my MSI board was RMA'ed i bought a Asus Deluxe e board from newegg. And that board was telling me Processor test Failed. Intel called me last night. There taking it back. I looked on my MSI 478 slot for any signs of that Silver3 stuff left behind. But I can't see any. If I had known this was going to be such a pain I would have bought a Dell..lol.

My 160gb 7th generation shows "127gb" Could anyone help me please??

OK! it's not like im going to fill up the classic, iv'e only used 15gb! but basically.. my ipod broke like a month ago.. due to super glueing on the case and destroying the battery connecter.. but the hard drive has been lying around for some time.. so it turns out that the 120gb 6th generation ipod classic works with the 160gb 7th generation.. the motherboards are the exact same.. so I got a used 120gb and poped my hard drive in there.. works fine.. but had to restore it.. before that I backed it up.. eureka.. I had my classing back
Only one problem is this.. why is 127gb come up? Im using a brand new windows 7 laptop? could this be a computer issue?

Woow I am searching quite a while on this board
this is a good similare issue I have created.
I seems (for now self inflicted) by inserting a 160Gb disc into an 120GB ipod and having NOT LESS but more then120 yeah.....127 GB it works. (I noticed most people ran right over the facts....its more than 120.....)
Happiness for me here as well. But is there a way back ?
Firmware issues prevent me from going back.
Also the disc came from a grey 160 going into a grey 120 and now showing grey in a black 160. (as 127) and not working. But I can read as a external disc. Still iTunes can't read (it says......I can)
Hope this helps a bit.

RV042 wan2 shows red light on internet connection

I set up my RV042 with two ISPs, one charter internet and the other AT&T
DSL. My DSL modem all of a sudden shows a red light over the "internet" slot
showing that it's not working. When I remove the modem and hook up to a PC, it works fine. When I put back into WAN2 slot, the red light comes back on. I have it set up to find IP connection automatically. It has been working for a day or so, but now this crops up. I check with ATT support and they verfiy the modem is okay and getting a signal when I connect to PC.

AFter I posted the problem, my DSL modem just started its normal green light and never (almost never) went red again. The big problem is that when my cable modem went down for repair to cable, my Internet went down also. I wanted the dual wan router to make sure that when I was online that if one ISP went down I would have an automatic back up. I also wanted bonding or binding where with two ISP's I would get a combination of speeds to one large speed, but obviously the RV042 does not bond to an aggregate speed. I saw in your reply that you mentioned PPPoE setup. My DSL is set up along with the cable modem to "automatically obtain the IP address." Is this the wrong setup?

Bold 9900 not powering up no RED light

Hi,
A day back my Bold 9900 was hung while checking email, it remained for around 15 mts and I had to pull out the battery, since then it never powered up. Tried every tip and tricks of the forum but to no rescue.
The LED red light does not come up with / without battery and with /without charger connected and neither does it boot. I guess that motherboard power must be available as trackpadpad is showing gleamy sensor light inside.
Please help me with a technical solution.
Thanks,
Abhishek

Tried charging quickly/endlesslywithout battery, inserting battery while charging, tried apploader, tried connecting through desktop / web software update, tried getting detection of hardware through desktop to no success etc, and almost navigated all the solutions/workarounds/tricks posted in support forums. But all in vein. What could have possibly gone wrong ? Is it hardware failure ? Have not tried battery replacement as there was no issue with battery while it was working.

HELP what is this little red light on the front of my phone?

I know about the 3 sensors on the front of the phone on the top near the ear piece, and the one on the bottom on the right keeps showing a red light. It looks like a small red "C" with a little dot in it. When ever the phone becomes active the light comes on, and stays on for about 10 seconds after locking.
I just today affixed a new screen protector (invisible shield) and just now noticed it happening for the first time. I do work in a dimly lit room but never had this happen before.
What does this light mean and how do I stop it?

Could be a sensor. Or light leaking into the sensor from the screen

P6N SLI Platinum - Model 7350 - CPU Compatibility and 4 Red Lights

The CPU compatibility list shows that the Intel E6400 is "under testing". I have been running the subject motherboard with an E6400 for 2 months before a system failure.
The system would not post and the D-Bracket connector showed 4 red lights indicating processor damage or not installed properly. The processor was removed and reseated. Still no post. The processor was removed and replaced with a new E6400. Still 4 red lights. the power supply tested ok. All components were removed and reinstalled one at a time. Still 4 red lights. The mother board was removed from the case and tested outside the case with no components. Still 4 red lights.
Although Intel replaced the processor (as indicated above) one technician stated that the motherboard is "under testing" and he was concerned about long term compatibility.
My last recourse is to replace the 7350 motherboard but I want to be sure it is compatible with the E6400.
Any help or advice regarding the compatibility issue or the 4 red light failure issue is appreciated.
Thanks.

Tried resetting CMOS several times (pushed button). Power Supply disconnected. Removed battery. Replaced battery. Motherboard out of case. only thing installed is video card. Still 4 red lights.
Should also tell you that memory was removed from 2 slots and put back into 1 slot. No change.
Is this motherboard compatible with the E6400?

System won't post-four red lights on D-Bracket

My system sometimes posts and sometime no; the D-Bracket shows four red lights, but if I press the start button on the case for 5 seconds, the system restart and all works fine !!!
What's the problem ?

Alipio:
Since this is a second thread of same problem, please select "pencil button" at bottom and delete it.

Displays red light for 20 seconds then goes out. nothing else happens. have tried charging it on the computer and all night in power point. wont show up in itunes or my computer

i bought my daughters ipod shuffle 4th gen last week for xmas. set them all up easily etc and wrapped them for xmas. kids opened them up for xmas played them most of the day so i thought i would charge them both overnight on the computer. pc went into sleep mode which i didnt realise wouldnt charge them. so in the morning they were flat so i charged them on the pc but 1 didnt seem to take any charge while the other worked perfectly. treid to charge it all night long last night using a power point charger and still this morning it displays the red light and wont show up in itunes or my computer. apple support havent rang me yet

Make an appointment at an Apple store if there is one nearby.

Ipod shuffle 1GB Re: how to resurrect a dead shuffle? Nov 5, 2008 4:42 AM (in response to Ipod shuffle 1GB) there is no sound cant find in Itunes not in showing in drive's list please tell me how to restore or reset red light showing when try to power on

Ipod shuffle 1GB
Re: how to resurrect a dead shuffle?
Nov 5, 2008 4:42 AM (in response to Ipod shuffle 1GB)
there is no sound cant find in Itunes not in showing in drive's list please tell me how to restore or reset red light showing when try to power on or conect with USB....
If you can plz help to fiX it
thanx
intel pc , Windows 7, core 2 Dule Core

Here is the answer: go to http://support.apple.com In the search box at the top left type in the number 304996 and hit enter. This will bring you to a page with 4 solutions. Click on solution number 1 and follow the instructions. This should fix it.
bigdogdan

My MacBook Pro retina 2013 won't charge. I've checked all connections which are all ok. Little red light shows on magnetic plug, instead of usual green.

My MacBook Pro retina 2013 won't charge. I've checked all connections which are all ok. Little red light shows on magnetic plug, instead of usual green.

If you are seeing a Red LED, you may have a faulty MagSafe Adapter.
I remember reading that the orange light is produced by a combination of a Red and Green LED. If that's the case, It seems that the adapter isn't lighting the green LED properly at that time.
I would suggest you seek service with your nearest Genius Bar (Apple Retail Store) or Apple Authorised Service Provider as they have access to diagnostics which may assist in isolating any hardware issues you may be experiencing.
Cheers.

I cannot hear any songs or movies from my laptop speakers - the headphone port works and a red light is showing? The output sound settings are showing as digital optical only? Any ideas :)

I cannot hear any songs or movies from my laptop speakers - the headphone port works and a red light is showing from the port? The output sound settings are showing as digital optical only? I used the headphones in the laptop for the first time yesterday and have had this problem ever since. Any ideas

The internal switch in the audio output port is stuck. Try inserting the earphone plug a few times. If no success, try jiggling a tooth pick inside in order to trip the switch.. If still no success, have the technicians at the Apple store genius bar do it for you.
Ciao.

My ipod is always showing red light even it gets fully charged can u pls suggest me a solution

my ipod is showing red light even it gets fully charged

okay I've sorta of fixed it. I don't know it just started to get recognized by the computer but I still ahve a problem. My iPod shows the apple logo and it's lit up and it's NOT GOING AWAY NO MATTER WHAT. Someone help me please.
I've like tried EVERYTHING.

My storm 9530 is showing a red light ..HELP ME PLEASE !!!

Similar Messages

Maybe you are looking for