N73 - problem - sound cuts out in calls - please a...

Hi, I have an N73 and it's been fine (apart from the top of the joystick falling off and the charger just deciding to stop working) but now I have a major problem.
When I make a call or someone calls me the phone just cuts out all the time as if there is a very bad reception. I've made sure the reception isn't the case and it seems the person on the other end of the line can hear me fine. I've also tried turning the volume down, up, turning the phone on, off. It doesn't do this in every call, but I have to avoid using it because it will do it on at least 90% of calls! The phone is generally in good condition and I do look after it (I'm stuck with it for 18 months) I use this phone for work and it's embarassing and impossible sometimes, T-Mobile won't do anything and I'm very close to throwing it at a wall when it does this!
Anyone else got this problem? Anyone know what I can do?!
Alisdair

Hi
cool down.
I am here.
I guess the nu FW has this problem.
However if your phone doesnt have the latest FW, check it *#0000# upgrade it.
Or if it is havin, try reinstallin it.
Or, you can do a hard reset, *#7370#.
Next, if all of thses things fails, take trip to nokia care.

Similar Messages

Video problem - sound cuts out after 29 minutes.

I have put some TV shows from my computer onto my iPod but after 29 minutes, the sound cuts out and I am left with just the video. If I skip past 29 minutes, the screen goes black for a second, then returns to the previous menu.
My iPod is a 30GB 5G with iPod Software version 1.2.
I used iTunes 7 and tried 7.0.1 to copy the videos to my iPod. They play fine on the computer.
I have put films (1hr+) on before and they have worked fine, however that was with iPod software 1.1 and an older version of iTunes.
Any ideas?

Well sounds like the TV shows had transferred errors. Have you tried reloading them?
Also make sure the Frame rate, and Audio rate are working ok. You will know if they are not, if voice and video are off even slightly. Also how long are the TV shows? 30 Min? If they are, then it may just be a corruption or skipped of the last min or few seconds, because the video is ending. That would explain the black screen. It does that after the video finished and it goes back to the last screen. So it just may have not copied the last few sec of the video, that happens sometimes. Try reloading it again!
Also if that does not work, try resetting the Ipod. I would hate for you to “Restore” your Ipod for just 30-60 sec of lost sound of a TV show. Especially if everything else if working well.
Best of luck. Don’t forget, if this post helped you, click Solved or Helped at the top of the post. It makes our rank better!
Have a great day, and hope you fix your problem.
P.s. it could just be that your Tv shows End at 29 min-ish as well IDK?
God life

Sound cuts out after 1 sec on .avi files in QuickTime

First, let me preface this post by saying that I have spent about a week searching through different posts in these and other forums regarding similar issues, and have yet to find a solution that works for me.
So I have been trying to play certain .avi files with QuickTime that I BELIEVE have been encoded with the XviD codec. At first, no sound played at all. After installing a bunch of different codec files, including packages such as Perian and codecs such as DivX, XviD, and AC3. I finally managed to get QuickTime to play these videos with sound for about a second, after which the sound cuts out. Also, if I rewind or skip to another point in the video, the sound will restart again for about one second and then cut out once more.
I should mention that these videos work perfectly when I play them with the DivX player. Does anyone have any suggestions or anyone with similar issues? I am currently running OS X 10.7 (Lion) on a new MacBook Pro 15"

After installing a bunch of different codec files, including packages such as Perian and codecs such as DivX, XviD, and AC3. I finally managed to get QuickTime to play these videos with sound for about a second, after which the sound cuts out. Also, if I rewind or skip to another point in the video, the sound will restart again for about one second and then cut out once more...Does anyone have any suggestions or anyone with similar issues?
As stated on the Perian "Support" web page, "Please consider removing obsolete QuickTime Components: FFusion, Xvid Delegate, 3ivX, DivX, DivX Decoder, XviD, msmpeg4v1, msmpeg4v2, AviImporter, EX_M4S2, Casio AVI Importer, AC3 Codec, and MatroskaQT." Having multiple codecs for the same compression formats can create component conflicts. Since Perian component package supports all of the named codecs, it is not necessary to have both Perian and the named codecs simultaneously installed.
In addition, Lion seems to also be prone to conflicts with third-party software apps and hardware peripheral casrds/devices. If possible, it is usually best to disconnect/close anything you can during the tests. Also, it might be a good idea to test the same files on alternative systems. (I.e., if possible, you might like to post a sample problem file to see if others can play them without problem on other platforms operating under Lion OS as a further conflict test.)

T410 - sound cuts out during playback, resumes after pressing volup or voldown

hello, I am using T410 with Win& x64, more more than 2yrs. Last week the sound playback issue occured. This happens with video and audio playback of any file type. After 2-3 mins of normal playback sound cuts out, but resumes right after I press vol up or down. Then after 2-3 mins it cuts out again and so on. I dont believe its a software -related error, since sound does not play even with Knoppix Live CD. Latest drivers and BIOS updates are properly installed. windows sound test finishes succesfully. I have read similar posts but all were related to software configuration. I have also replaced the speakers without change. Is there a known fix, or even a fix at all? Thanks

Yes, videos, music, online, off-line and even window sounds, all audio turns off. Sometimes messing with the volume slider or mute button will bring it back on but eventually neither of these work and I have no audio period until I restart the computer and then the cycle starts over. For my business I create informational short videos or audios and use internet calling. I also attend trainings and meetings online. Sound cuts out first every few minutes and gradually increasing until it will not come back on at all. I purchased a small bluetooth speaker and use that but it is a pain to move, along with the laptop, when I am moving from one room or location to another. Thought it would be a temporary solution until I could get the internal speakers working but since that is unlikely to happen purchased clipon speakers to make it easier to transport. This is not some off brand, $350 computer but supposedly a quality business computer, which is what I paid for but did not receive. As I said, I have searched the internet and found hundreds of post regarding this problem on both 410s and 510s.

Onboard Sound Cuts out after a while - anyone know why?

Hiya peeps,
Ever since I bought my MSI motherboard, the onboard sound has been a bit dodgy. Whenever I play games like UT2004 or halflife, the sound cuts out after several minutes of play. It only comes back again if I restart the game, but then after a few minutes it will cut out again. Anyone else experienced this?
I have tried altering all the game settings from safe mode sound drivers to full EAX H/W accelerated but this has made no difference to the stability of the audio. I have been updating all the drivers to my system as and when MSI live update picks them up, os I am up to date on that front. I have a lot of decent kit (PSU etc) in my machine and its not overclocked in any way at all. Also I have the most up to date direct x too.
My system spec is below, please help chaps.
PS im trying here as MSI have not responded to any of my email queries about this problem.
Regards,
MrG.
CPU: P4 2.8E Prescott 800FSB (200MHz * 14.0) HT Enabled
MEM: 1GB Corsair XMS3200C2PT Platinum CAS2
MTB: MSI 865PE Neo2-PFISR (MS-6728) Bios V3.7
GFX: GexCube Radeon 9800 Pro
HDD: Hitachi Deskstar 7K250 120GB ATA-100 8MB
PSU: Enermax EG465AX-VE(G)(FMA) 460W
OS : WinXP SP1, all drivers up-to-date and Liveupdate up-to-date
Nothing is overclocked and all BIOS setitngs are set to the defaults.

I had the same problem, this is how i fixed it:
Uninstall everything relating to the drivers for your sound from both the control panel AND the device manager, do not let windows PnP install ANY drivers. Then manually install the latest drivers, not from live update, but from MSI's website, then run the installer package. Make sure you reboot at every step, since that's what I did, and no more sound cut-out.
See, we have many of the same specs in our computers, this is probably the same issue I had.

My brand new iphone 5 cuts out during calls all the time, doesn't send mt text messages and then when it does it sends them twice?! why?? is it just apple or my network provider? bearing in mind my iphone 4 did exactly the same, so its a new handset sim

Hi,
i have just updated my iphone 4 16gb to an iphone 5 16gb
The iphone 4 had horrific problems, for example: Cutting out on calls, it going silent, me not being able to hear the person i was speaking to and them being able to hear me, and then visa vera.. also the main button at the bottom started to break.. my text messages weren't sending and then when they did they would send several of the same one.. also with mixed messages in them.. some of the texts had been form ages ago and had been deleted anyway and bits of them would re appear in the middle of the text, but only show to the person recieveing the text.
I thought all of this might have been some water damage as i had nearly had it for 2 years... However on Tuesday.. ( 29th Jan) i recieved my new upgrade of the iphone 5.. i was so excited, but then today.. 2 days after recieving it, its starting to do EXACTLY the same things my old phone did... cutting me off, going quiet on the phone, not sending texts, then sending several ones... sending mixed texts. Safe to say i am fuming!!! i am with vodafone and rang them today asking why?! they said it couldnt be my handset as its a new one, couldnt be the sim because thats new too so it must be the area signal.. so she checked for me.. came back to me and said that the signal in my area is perfectly fine....?!?!?! that makes it even worse!!! so i have asked to return it....!! i was going to go with a different provider thinking that it was vodafone??but after looking on here it seems like its apple? i am very disappointed as i love everything else about the phone, but its impossible to have a phone like this! especially when i use it for work too!

My wife is having the same problems as a reciever. She works in a school as a teaching assistant and her teacher sends messages that are mixed with previous texts from ages ago.
Can anyone shed some light on this problem or is it only her and this poster?
2m42s

Sound Cutting Out on Standard Def Channels with or wthout DVR

Hi!
We are having occasional sound drop-out problems. They seem to only be happening on standard def channels although we have a hi-def box. (We often record sitcoms and kids shows in standard def to save room on the DVR.)
The problem is that the sound cuts out for a fraction of a second (just long enough to notice) at random spots. If we rewind and play it back, it still drops out in the same spot so it seems the issue is with the signal getting to the box from the outside line, not an hdmi cable issue as I've seen mentioned elsewhere.
The issue occurs whether we're watching a previously recorded show or a "live" one (understanding that even the live shows are delayed a few seconds to enable the DVR to record it).
I've seen other sound issues related to switching channels but this is not the case here.
I've also had it happen on a small TV with no box. We just have the coax going right into the display to watch standard def network shows on it. This leads me to think it's a signal issue, not a DVR one.
Anyone else have this and/or have any luck in getting it resolved?
Thanks!
Jeff

Hello Jeff,
I am sorry to hear that you are having trouble with the sound on the Set Top Boxes. I sent you a private message to further assist you.
Thanks,
Shamika_Vz
Verizon Support
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

Sound cuts out after any given amount of time, only way to turn back on is to reboot.

For reference, I am using a fully up-to-date mid-2012 model rMBP. Attached to my MacBook via USB I also have an M-Audio KeyStation 49i, which is where I have my headphones plugged in (probably not related in any way, but just noting this).
I first encountered this issue while using Chrome and listening to music on SoundCloud with Garageband open after the last Mavericks update yesterday. I initially thought it was a Chrome bug, and in doing some research, I found that other Chrome users were having the same issue as me, but it was related to PepperFlash (a version of the standard Flash player), and disabling it in Chrome Canary fixed the issue for them.
Unfortunately, it did not fix the issue for me, but I have refrained from using Chrome since then and stuck to Safari to ensure that it's not two issues with the same outcome.
Then I stumbled across all of the Mavericks users that are having sound problems; anything from crackling/popping to not working at all. It seemed, though, that everyone that was having the sound cut out for them entirely were not only having this happen after their laptops came back from sleep mode (which is not the case for me), but were able to fix it by restarting Coreaudio[d] or -- if they had been using the headphone jack on their Macs -- they just had to plug it in again and take it back out. Neither of these worked or were applicable to my situation. Some were able to get it working again by resetting the PRAM/NVRAM, and a few others seemed to be able to bypass the issue by using Soundflower, but neither of these solutions worked for me either. The only way I can get sound to work again is to restart my computer entirely.
After doing so, I am only able to listen to audio for a certain amount of time. It seems to vary depending on how much memory the task is taking up. Like I'll be able to listen to a track or two on SoundCloud, or attempt to record into Garageband for five minutes or so. If I'm in a Garageband project that already has a lot of tracks, I'll be lucky if I can even get through a few seconds before it cuts out entirely. There are very quiet crackling/pop sounds every once and awhile, but it is hard for me to distinguish if that is just the natural state of the hardware I am using or if it is related to background system sounds.
I'm at wit's end trying to figure out what the problem is, mostly because there are so many others with similar issues and varying hardware/software setups that it's hard to track down exactly what my own situation is.
I'd like to know where I should be exporting any error logs from so that someone can take a look at this issue.
Thank you.

After doing some additional testing, I was able to get the sound working again without rebooting by:
1. Unplugging the MIDI device.
2. Resetting the audio input and output to "built-in".
3. Plugging back in the MIDI device.
4. Changing the audio input and output back to the MIDI device.
Still, though, the sound only lasts for a little while, and there doesn't seem to be anything indicating how or why it stops.

AX - sound cuts out, becomes metallic, stops

Hi All:
Can't find this issue in the forums. If there's a thread, please point me to it!
For the first time today my 3-year-old AX began to behave strangely. We've always kept it up to date, so it has the latest firmware.
This afternoon we were streaming our fave radio station SOMA.fm when the sound cut out for a moment, then restarted as a thin metallic stream. It sounded rather as if i were listening to weird jazz cymbal solo. After about 20 seconds of that, the stream just died.
We tried changing the channel - no luck. We tried rebooting - no luck. Firmware is up-to-date. Same stream plays fine through our Macbook. Every time we restart, same behavior - streams fine for a minute, cuts out, becomes metallic, then stops.
Any idea of root cause or another troubleshooting idea? It's always "just worked" until now from the moment we unwrapped it and plugged it in, so we're confused!
Ty!
F

If you temporarily connect a pair of stereo headphones to the audio port of the AX, does the sound quality improve?
If not, how about using a different audio source? For example, instead of the Internet radio stream to use an AAC or Apple Lossless file?
If the sound does not improve with either of these, then it is possible the audio circuit in the AX that provides analog output is faulty.

My ipod video sound cuts out after 30 sec

I play my movie and the sound cuts out after a while and then it only plays the video with no sound. It's not the video because it works fine on my computer and all the other videos are doing the same thing. I found if I rewind or fast foreward the sound comes back but only for a little while and the sound cuts out again.

This happens with the current firmware 1.1 upgrade on the iPod. You can downgrade the firmware to 1.0 and this will solve that problem. Doing it this way you won't have to restore the iPod which will erase it. If you can't do this then you can restore the iPod using the previous updater.
How To: Downgrade iPod Firmware
http://forums.ipodhacks.com/showthread.php?threadid=813
The other option is to use QT Pro which will work to correct the problem:
http://forums.ilounge.com/showthread.php?s=&threadid=146142
1) Open up the Video file in Quicktime Pro
2) Select File->Export
3) Select "Movie to MPEG-4" beside "Export:", then click the OPtions button
4) Select "Video" & make sure the "Video Format" is set to "Pass through"
5) Do the same for "Audio", then hit OK
6) Save the file

Sound cutting out/crackling/pops in Windows 7 XFi XtremeGamer

System specs:
Windows 7 Ultimate fully updated
Q6600 @ 3.0ghz
Asus P5N32-E Sli Motherboard (680i Chipset) 80 bios revision w/ nVidia 5.5 nforce drivers
2x2 Gigs Corsair ?DDR2 800 @
In dual channel mode
BFG 285-GTX w/ 96.2 drivers
X-Fi XtremeGamer w/ PCDRV_LB2_8_003 drivers
With this setup I am unable to use CMSS 3D without the audio cutting out completely. Before it does so it's usually followed with numerous cracks and po
ps.
Disabling CMSS 3D alleviates this problem, however I occasionally get a slight pops and crackles when playing games or listening to music.
While playing Mass Effect 2 the sound will completely cut out in the same manner it does when I have CMSS 3D enabled, despite the option being turned off in the console launcher.
At first I tried a clean install of the drivers, removing drivers, using driver cleaner pro, registry cleaner and then reinstalling them. Did not fix the issue. I then did the same for the chipset drivers and my video card drivers.
I thought it may have been a problem with OpenAL (for mass effect 2) so I reinstalled that. Same problem.
I tried using PAX's driver's, same problem.
I've used DPC Latency Checker V.2.0 and according to it my machine should be able to handle real-time streaming audio with no dropouts.
I'm at a loss at what else to do and any further help would be appreciated.

Just an update on my problem.
I was able to resolve the sound cutting out issue and the cracks/pops issue within windows by disabling CMSS3D + setting my sample rate to 24 bit, 96k Hz.. Using 92k Hz results in the cracks and pops coming back, although they are few and far between.
Unfortunately this did not resolve my issue with the sound/audio cutting out in mass effect 2. I tried the onboard sound and that also cuts out, so I've determined it's not a hardware issue but rather a bug of some sort within the game. There are also other sparse reports of people having the same issue.
Thanks

Sound Cuts Out During Playback-Sound Card/Audio Interface Necessary?-

I'm a voiceover artist with the following setup:
Sennheiser MKH 416 P48 U3 Microphone
Yamaha HS80M Reference Monitors
Mackie Onyx-i 1220 Mixer
Adobe Audition CS6
Dell Inspiron 1720 laptop (Intel Core2 Duo, CPU T5750 @ 2GHz, 32-bit)
Until recently, I could hear anything I recorded or pre-recorded items with no issues. However, now, as I listen to anything, the sound 'cuts out' (latency issues?). The meters on Audition will still be moving, but I'll get no sound from my monitors. I upgraded to Windows 7, hoping and thinking this would solve the issue, and that Audition would play nicely with Windows 7. This 'solution' seemed to have helped, but ultimately, it did not resolve my issue. At this point, I believe it's my sound card. My studio quality setup seems to be too much for my consumer grade sound card. Because my Mackie has an interface built into it, I did not believe that I needed an interface. However, I'm beginning to question that. So, that's part of my question. Is an audio interface necessary for me even though I have one built into my Mackie? If so, based on what I list for my system, does anyone have any recommendations for interfaces? If I do not need an interface, I'd appreciate any suggestions or ideas as to what's causing the sound to 'cut out' and how to resolve it. Any and all help, I thank you for it in advance!
E

Finally! I wrote a reply a few hours back but the fine folks at Adobe took the site down just before I hit send! Lucky I saved it elsewhere because the "recovered post" was only the first couple of paragraphs.
Anyhow, take 2.
Well, first off, your Mackie Onyx mixer has a firewire interface built in so it, in effect, becomes your sound card. The one in your computer isn't involved in the recording/playback process at all (at least not unless you're trying to do something like monitor via the computer card rather than the mixer). Therefore, buying another sound card/interface won't help at all.
Similarly, audio dropouts aren't a latency issue, at least not directly. Latency is the delay in the audio as it does the round trip via you sound interface (mixer) and computer. It's more of an issue for musicians trying to be beat accurate as they over dub tracks. However, the latency controls could be affecting your drop out problem. The latency control in Audition is effectively controlling the buffer size--and having a larger buffer (which increases latency) also gives you playback more protection against glitches when your computer gets busy doing something else. So...the first thing to try is increasing the latency/buffer size on the Edit/Preferences/Audio Hardware menu.
Another thing to check is that you're using the latest drivers from Mackie--check their site and download/install the latest if there are some available. If there's a choice, go for ASIO drivers rather than MME if there are some available.
Also, I mentioned your computer getting busy with other things--for serious sound work shut down everything else on your computer. Pay special attention to networking, wifi, and anti virus software, all of which are usualy prioritised to grab processor cycles over your sound work. Also make sure you shut down all system sounds.
Hope at least one of these suggestions works for you.

Battlefield 2 Sound Cutting out Issue - Possible

This is for anyone who has been experiencing the sound issue in Battlefield 2, where the sound of your gun all of a sudden goes out in the middle of a match AFTER it worked before.
There was threads where people told others to download the BETA driver, which I wasnt going to do. Then there was a thread where someone said something about the OPENAL file that you had to update from Creative. That wasnt it either.
My BF2 Sound Settings BEFORE : Hardware, Quality High, EAX on.
All I did was change one thing. Switch from "Hardware" to "Software". I was able to play round after round after round, and no sound cut out. It seems that its either EA or Creative not coming through for us who have SB Audigy 2 cards. Hopefully a patch or a REAL driver will come out soon and fix this. This is why we got the "Hardware" right?
Hope this helps all!

Well, I'm using a Audigy2 ZS Platinum Pro card, and haven't experienced any sound problems in both the demo and the full release version.
Am using hardware + EAX + HIGH, in the audio menu.
Haven't installed Creative's latest beta drivers. As I don't like to mess around with beta releases, that have been pushed out early to improve support for a few game titles.
Anyways, this post was just to let you know, that it's possible to play BF2 without sound issues!

Iphone 5 cutting out mid-call

I have had problems with my 5 cutting out mid-call. It's happened several times with different callers, which makes me think it's my phone. It gives me the 'call failed' screen. There is no apparent reason for it - no signal drop, for instance - and so I wondered if this is a common problem or whether I have a duff phone and need to return it. Thoughts?

I've had the reception (tinny, robotic voice, intermitent voice quality) since purchasing my iPhone 5 two days ago.
Yesterday I had to go to the Verizon store (sent there by online tech from Verizon). I was talking on my phone to a friend as I drove to the Verizon store and as I pulled into the parking lot of the store (with 5 full bars on 3G) the call got dropped and "Call Failed" showed up on the screen. I looked at the phone to make sure I had service and I did, full bars all the way ??

Music choice channels ,sound cutting out

music choice channels , all of them, the sound cuts out like a skipping record.i have had online tech service tell me to re start the cable box. 2 times in the past 2 weeks, this sometimes works.new box, new hdmi cable. same problem, this is very frustrating as we like to relax to music and not have to keep "fixing" with a re-boot. what is the permanent fix?

ssroadstar1 wrote:
music choice channels , all of them, the sound cuts out like a skipping record.
i have had online tech service tell me to re start the cable box. 2 times in the past 2 weeks, this sometimes works.
new box, new hdmi cable. same problem, this is very frustrating as we like to relax to music and not have to keep "fixing" with a re-boot. what is the permanent fix?
Apologies for the issue and the experience that you described above. I have asked a colleague to review your account and reach out to you so that we can get any underlying issues identified and resolved.
Thanks for your patience.

N73 - problem - sound cuts out in calls - please a...

Similar Messages

Maybe you are looking for