NAC Error Message in 4500 Switch

Hi There,
I have a 4507R core Switch running IOS version 12.2(31). I am trying to configure this switch for Clean Access; I have already configured the ACS server but when configuring the switch as a NAD and apply the "ip admission NAC" command on the interface level, I get the following error message:
% This config is not supported on this platform. Try configuring a new rule.
The NAC configuration I entered on the switch is as follows:
Switch(config)=ip access-list extended Interface_ACL
Switch(config-nacl)=permit udp any any eq 21862
Switch(config-nacl)=permit udp any any eq domain
Switch(config-nacl)=permit udp any any eq bootpc
Switch(config-nacl)=permit udp any any eq bootps
Switch(config-nacl)=permit tcp any host (antivirus ip address)
Switch(config)=ip admission name NAC eapoudp
Can somebody clarify to me the meaning of that error message and assist me whether my NAC configuration is alright?
Thanking in advance.
Regards,
Haitham

Hello All,
I just figured out the problem; you need first to configure the following commands before applying the ip admission command:
switchport mode access
switchport access vlan
Thanks to all.
Regards,
Haitham

Similar Messages

Error message on 4500 switch please help me rectify this issue .

LLog Buffer (4096 bytes):
valid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
4d15h: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 2 times)Packet recei ved with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
4d21h: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 5196 times)Packet re ceived with invalid source MAC address (00:00:00:00:00:00) on port Po1 in vlan 1
5d04h: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 58415 times)Packet r eceived with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vla n 1
5d10h: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 44163 times)Packet r eceived with invalid source MAC address (00:00:00:00:00:00) on port Po1 in vlan 1
5d17h: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 18786 times)Packet r eceived with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vla n 1
5d23h: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 4897 times)Packet re ceived with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
6d06h: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 7 times)Packet recei ved with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
6d14h: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 16 times)Packet rece ived with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
6d22h: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 8 times)Packet recei ved with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w0d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 6 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w0d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 6 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w0d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 27713 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w1d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 89677 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w1d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 38722 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w1d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 7 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w1d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 22133 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w2d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 46596 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w2d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 11 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w2d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 10 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w2d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 26497 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po1 in vlan 1
1w3d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 61085 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w3d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 5 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Gi2/1 in vlan 1
1w3d: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 11 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po2 in vlan 1
1w3d: %C4K_REDUNDANCY-5-CONFIGSYNC: The private-config has been successfully synchronized to the standby supervisor
1w3d: %C4K_REDUNDANCY-5-CONFIGSYNC: The startup-config has been successfully synchronized to the standby supervisor
1w3d: %SYS-5-CONFIG_I:
Please help me with trouble shooting steps and also commands..........

Hi,
Please ask the question in LAN SWITCHING community for speedy response but it looks like a message indicating that Switch is seeing a packet with src mac 00.00.00.00.00.00 which obviously is Invalid. Switch learns the mac from src in the frame and it is wrong. Looks like Mac-spoofing.
Regards,
KANWAL

Cisco Nac Error message

Hi.
Today I found one of my standby NAC servers is down. The power switch in front shows amber and the power supply behind too shows amber. When accessing through serial i see the following output. What could be wrong?
Regards
Prasanth George

Hi
I did remove the power and reconnected the power. Still it ends in ILO. Even if i continously keep pressing the power button in front, the light keeps remaining amber. Its model is 3140 CAS server
Any suggestions?
Regards
Prasanth Mathews

Cisco switch 3750x TE Error Message

Dears
Hello
PLease I faced the following Error Message in my switch c3750x TE ver 15 , please let me know what is this error , does my switch has bug ?
%TCP-2-INVALIDTCB: Invalid TCB pointer: 0x7B7A89C -Process= "HTTP CORE", ipl= 0, pid= 301
-Traceback= 4FF410z 11ED788z 11CDA1Cz 11D53A4z CF3D84z CF4190z CFB78Cz CEDEB8z 26E07A8z 26DAD58z
Jan 7 07:08:22.264: %TCP-2-INVALIDTCB: Invalid TCB pointer: 0x6D4BC2C -Process= "HTTP CORE", ipl= 0, pid= 301
-Traceback= 4FF410z 11ED788z 11CDA1Cz 11D53A4z CF3D84z CF4190z CFB78Cz CEDEB8z 26E07A8z 26DAD58z
Jan 7 07:08:22.272: %TCP-2-INVALIDTCB: Invalid TCB pointer: 0x5448928 -Process= "HTTP CORE", ipl= 0, pid= 301
-Traceback= 4FF410z 11ED788z 11CDA1Cz 11D53A4z CF3D84z CF4190z CFB78Cz CEDEB8z 26E07A8z 26DAD58z
Jan 7 07:08:22.281: %TCP-2-INVALIDTCB: Invalid TCB pointer: 0x7B8D718 -Process= "HTTP CORE", ipl= 0, pid= 301
-Traceback= 4FF410z 11ED788z 11CDA1Cz 11D53A4z CF3D84z CF4190z CFB78Cz CEDEB8z 26E07A8z 26DAD58z
Jan 8 01:47:14.816: %IPC-2-INVALIDZONE: Invalid IPC Zone 0x60000000.
-Traceback= 4FF410z DC93DCz 62D3Cz 62E44z 26E07A8z 26DAD58z
Jan 8 01:47:34.772: %IPC-2-INVALIDZONE: Invalid IPC Zone 0xB0000000.
-Traceback= 4FF410z DC93DCz 62D3Cz 62E44z 26E07A8z 26DAD58z
Jan 8 01:47:55.660: %IPC-2-INVALIDZONE: Invalid IPC Zone 0x20000000.
-Traceback= 4FF410z DC93DCz 62D3Cz 62E44z 26E07A8z 26DAD58z
Jan 8 01:48:16.698: %IPC-2-INVALIDZONE: Invalid IPC Zone 0x20000000.
-Traceback= 4FF410z DC93DCz 62D3Cz 62E44z 26E07A8z 26DAD58z
Switch Ports Model SW Version SW Image
* 1 30 WS-C3750X-24 15.0(2)SE6 C3750E-UNIVERSALK9-M

I just did a lookup on the error, and this is the information I got. Theres not a lot of information here. And no similar bugs on the 3750X recorded.

No Disk error Messages in PSE8

On and off I keep getting the following error message when I switch between Edit and Orgainzier in PSE8
and sometime other times. Photoshop ElementsOrgainzer.exe-No Disk There is no disk in the
drive. Please insert a disk into drive \Device\Harddisk4\DR4.
I have to hit Cancel 3-4 times to get rid of it.
What is this and how do I stop it? Tks. ALan

I have recently experienced this message repeatedly in PSE6 running on Vista. I believe after either saving a file from PSE6 to a floppy in drive A or opening a file in PSE6 from an SD memory card in drive J. Resolved by recreating both situations then ensuring that i used photoshop to open files from and save files to the resident C drive before removing the floppy disk from drive A and using the 'safely remove hardware' function in Vista to confirm that it was safe to remove the SD card.
Following this procedure I have experienced no more 'no disk error messages'

Error message of MAC flapping for CCM-UC installed in UCS server

Dear All,
I have a strange issue, I have the 2 UCS servers setup with CCM & unity Connection running on each server on PUB - SUB mode.
I'm getting following error message on the Switch where the UCS server Connects.
I'm unable to trace why we are getting this error message, There is no problem with accessing CCM or UC, also the Phone & Voice mail seem to working.
un 25 13:15:14.853: %SW_MATM-4-MACFLAP_NOTIF: Host 000c.2911.db00 in vlan 410 is flapping between port Gi1/0/34 and port Gi1/0/33
Jun 25 13:15:28.828: %SW_MATM-4-MACFLAP_NOTIF: Host 000c.2911.db00 in vlan 410 is flapping between port Gi1/0/34 and port Gi1/0/33
Jun 25 13:15:44.145: %SW_MATM-4-MACFLAP_NOTIF: Host 000c.2911.db00 in vlan 410 is flapping between port Gi1/0/34 and port Gi1/0/33
Has anybody expereinced such error before, Appreciate your help in tracing this error.
Thanks,
Oliver

Hello,
I believe you'll get better answer at:
"https://supportforums.cisco.com/search.jspa?peopleEnabled=true&userID=&containerType=14&container=2003&spotlight=true&q=UCS"
my best guess is to check the LAN config on the UCS. It seems its trying to load balance the traffic in Active-Active rather than Active-Standby.
HTH

NI-PAL Service Manager Error Message

Hello Fellow LabVIEW users
I am getting error message everytime I switch on my computer as shown in the attached image file.
1) what is the NI-PAL? I could not find any help topics related to it.
2) Why is this error message shown? Could it be because I changed the PCI port for my GPIB card?
3) How do I overcome this issue? Is it a major problem?
Thanks
mhaque
Attachments:
error message.JPG ‏44 KB

Mhaque,
May be the following link help for u..
http://forums.ni.com/t5/LabVIEW/NI-PAL-service-manager-generate-an-error-at-the-startup-of-the/td-p/...
Siva
Sivaraj M.S
CLD

I have just switched over to iCloud and I am now getting an error message in iCal which is the following: The server is currently unable to handle the connection due to a temporary overloading or maintenance of the server. If this continues you should con

I have recently switched from MobileMe to iCloud and I now getting an error message in iCal :
"The server is currently unable to handle the connection due to a temporary overloading or maintenance of the server. If this continues you should contact the server administrator.
You may try to connect to the server again or take the account offline."
Since I am working from home and I am not on a server other than iCloud I don't understand why I am getting this message. (for 3 days). How do I fix it?

TomCT60,
Is your MacBook using Mac OS X 10.6.8 as indicated in your post? If so you will not be able to fully integrate with iCloud.
iCloud and Snow Leopard, by Roger Wilmut describes what iCloud options are available for Snow Leopard.
If you are using Lion, go to iCal>Preferences...>Accounts, and delete/re-add your iCloud CalDAV server.

Why do I get an error message when I tried to switch from Library module to the Develop module?

I've been using my LR3 for a few months but this is the first time that I got an error message when I was switching from the Library module to the the Develop module. I have a macbook pro with 500 GB HD. I am currently using 450 GB already. Anyone have an idea how I can fix this. Thank you.

Should we use our telepathy to figure out error message?

My ipad2 has locked. When I switch on its asks me to connect to iTunes which it does. Prompts me to restore and then gives an error message (11)

My ipad2 has crashed. Tried to do an update last night. Upload bar moved 1cm then locked stayed like that all night. I have switched off and then on again and its prompting me to connect to itunes. Once connected it says to restore. It starts this process and then stops with an error message (11) I cant access anything on it not even the battery charge indicator shows. What do I do?
Thanks

Which file is mentioned as the cause of that script error?<br />
Is that a file with a chrome protocol?

When I try and download app updates via wi-fi to my Ipad I get an error message "Your account is not valid for use in the Australian Store. You must switch to the US store before purchasing." I am in the US how do I switch?

When I try and download app updates via wi-fi to my Ipad I get an error message "Your account is not valid for use in the Australian store. Your must switch t the US store before purchasing. I am currently in the US on wi-fi. How do I switch

Change App Store
1. Tap "Settings"
2. Tap "iTunes & App Stores"
3. Tap on your Apple ID
4.Tap "View Apple ID"
5. Enter your user name and password.
6. Tap "Country/Region."
7. Tap "Change Country/Region"
8. Select the country/region where you are located.
9. Tap "Done".
Note: If the change doesn't take effect, sign out of account and sign in again.

Problems after downloading the lastest version of iTunes for my iPod Touch. Now whenever I switch on my laptop and access the internet I get an error message. 2nd time this has happened and I'm fed up trying to fix it. Anybody having similar problems?

I've downloaded iTunes 10.5 onto my iPod Touch, no problems but I've now got a constant error message on my laptop everytime I switch it on and access the internet. The message is "The procedure entry point xmlTextReaderConstName could not be located in the dynamic link library libxml2.dll"
This is the 2nd time this has happened. Last time iTunes Support called and we ran through a load of checks to no avail. The only option was to delete iTunes completely off my laptop and go for a new download of it. Can anybody tell me how to do it - didn't write it down last time, silly me, never thought it would happen again. Also sent an email to iTunes Support - waiting for a response.

Maybe:
"Waiting for changes to be applied": Apple Support Communities
Also I requested that your email address be deleted. Personal responses are not given in this forum

When i attempt to download a 'free' app from the app store error message comes up: "Account Not in this store- your account is not valid for use in the US store. You must switch to the Guyanese store before purchasing."

when i attempt to download a 'free' app from the app store error message comes up: "Account Not in this store- your account is not valid for use in the US store. You must switch to the Guyanese store before purchasing."

Change App Store
1. Tap "Settings"
2. Tap "iTunes & App Stores"
3.Tap "View Apple ID"
4. Enter your user name and password.
5. Tap "Country/Region."
6. Tap "Change Country/Region"
7. Select the region where you will be located.
8. Tap "Done".

Iphone 4 switched off error message code 21

i phone 4 just switched its self off and wont restart and when connected to itunes for reboot we get error message code 21

Error 20, 21, 23, 26, 28, 29, 34, 36, 37, 40
These errors typically occur when security software interferes with the restore and update process. FollowTroubleshooting security software issues to resolve this issue. In rare cases, these errors may be a hardware issue. If the errors persist on another computer, the device may need service.
Also, check your hosts file to verify that it's not blocking iTunes from communicating with the update server. See iTunes: Advanced iTunes Store troubleshooting—follow steps under the heading Blocked by configuration (Mac OS X / Windows) > Rebuild network information > Mac OS X > The hosts file may also be blocking the iTunes Store. If you have software used to perform unauthorized modifications to the iOS device, uninstall this software prior to editing the hosts file to prevent that software from automatically modifying the hosts file again on restart.

Had to switch MacBooks Now I'm getting error messages when I reinstall from backup

Had to switch MacBooks Now when I reinstall my adobe products onto the new computer I get an Error message (error #6) when I try and reinstall the programs (drag and drop) from my time machine backup onto my new computer. Im running what I believe is the adobe design suite CS 5.1 (It was purchased on disk in mid 2011) and the new computer does not have a disk drive to reinstall it that way

Restoring from Time Machine backups never works. It usually breaks the licensing mechanism.
Uninstall CS5, download CS5 from Download and Installation Help
Install then enter your serial number.

NAC Error Message in 4500 Switch

Similar Messages

Maybe you are looking for