Need Help For Bios Update...

Hi Buddies, my mobo (760GM-P23 (FX)) is working with an Athlon II X3 455, Kingston HyperX KHX1333C9D3B1K2/4G Dual Kit and with just on-board graphic. MSI Live Update shows the bios H.20 as my board's and H.A0 as upgrade version. Is this information correct?
I'm an inexperienced pc user. Is there any software which installs the bios update through windows' interface?
I'm using "Core Temp" software as processor heat controller. Any other advice which shows also the mobo's temperature?
Thanks in advance..

Quote from: motan on 22-October-12, 19:58:19
Thanks for help. How do I understand that the mobo needs a bios update?
if you have no issues, then leave bios update alone
Quote from: motan on 22-October-12, 20:04:47
Thanks for help. I tried to use it. Interestingly Control Center and Live Update are not working together. Just ones is working if I install it before than other. Second gives error as "Driver can't load".
Control Center need admin permissions to runs properly.

Similar Messages

  • Portege Z835 - need help with BIOS update

    Hello.
    I have a Portege Z835, with a battery problem: don't charge. The battery indicator says "3% connected and charging" but it don't charging the battery.
    Some forums says that the solution is updating the Bios. I have a Bios update v.1.60 ready for install. When I try to install, we get the message "the battery power is not enough".
    My power cord is always connected. If I disconnect the power cord, laptop is off.
    Please, what can I do?
    Thanks.
    GB.

    Hi
    Theoretically this issue could be related to faulty battery.
    As mentioned by Silas, even if the notebook is not ON the battery should be charged if AC adaptor is connected. So Im afraid its not BIOS issue and update would not help you.
    You can try this: If notebook is OFF, remove the battery.
    Now connect the AC adaptor and power up the unit now the OS should not report any battery statues since the battery is not plugged in.
    Now connect the battery and check if the battery charging status would change/increase.
    If this does nothing, would recommend testing new battery.

  • I Need Help in BIOS Update!!!

    Hey!! i got the 875p Neo LSR motherboard and the BIOS version that i currently have or got with my board was 1.4 and the LIVE Update 3 says the online version is 1.7. There was something to do with Flash BIOS or something and i tried it and my PC would not reboot. So i had to format my HDD and install Windowns again and it did work. That was another pc and i got the same board on my 2nd pc and i downloaded all the appropraite updated BIOS files from the Link given in another Thread on the forum so I was wondering if anyone could guide me through of how to install the new BIOS files, as i downloaded the 1.5, 1.6 and 1.7 ones, since i dont wanna end up with a dead board!! I am a newbie so pls help me out ppl !! Thank alot for ur cooperation!!  )

    Try these excellent threads:
    BIOS Flashing
    Live Update WARNING!! Read this first!
    BIOS flashing stupid or not?

  • Need help for reset bios password

    hello
    i need help for reset my bios password 
    my laptop is HP Pavillion tx 232
    code 59637760
    thank you 
    This question was solved.
    View Solution.

    Try
    46795366
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • I just bought more Ram how do I check for bios updates before I install it?

    I purchased 2 4GBs 200 PIN DDR2 of memory  from Crucial to upgrade my Pavillion notebook dv4t 1400 from 4 to 8 gbs
    Series (DDR2)  ( p/n NS244AV)
    I'm running Win 7 Ultimate 64bit service pack 1
    The directions say I need to check for bios updates with the maufacturer to see if I need to flash the bios before I install the new memory. How do I do that?
    thank you for your help
    This question was solved.
    View Solution.

    Please see "Updating the BIOS" to determine the current BIOS version installed and how to update the BIOS if needed. Please see the HP Pavilion dv4t-1400 CTO Entertainment Notebook PC Drivers & Downloads page for the most current BIOS version available for your computer. Click HP Notebook System BIOS Update (Intel Processors) version: F.66 A for a direct link to the BIOS download page.
    Please click the white KUDOS star to show your appreciation
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

  • Need help for cenvat reversal

    Hi Friends,
    Need help for cenvat reversal.
    Reversed MIRO by MR8M & MIGO by 102 movement but not able to post & cancel cenvat by J1IEX.
    In table J_1IEXCHDR status = "P" and J1I5 does not update for document of 102 movement because reversal document of MIGO, i.e. material document with 102 movement type does not have excise tab. MBSM-Cancelled Material Documents, does not show any of the material documents.
    Want to reverse the cenvat credit, please help.
    --Anil Bhamere

    Hi,
    If I select Cancellation in MIGO then there is only Material Document option.
    In MIGO Purchase Order option shows for Goods Receipt, Goods Issue and Subsequet Adj.
    In this case I have been selected Goods Receipt option followed by purchase order number by which original goods receipt MIGO was created, selected 102 movement type and from line item respective MIGO document. The reversal document created successfully where as original MIGO document does not show in cancelled document list. When post option selected from J1IEX and entered vendor excise number then message appeared as No Part I exists for availing credit in excise invoice xxxxx.
    If Cancel option selected from J1IEX and entered vendor excise number then message appeared as Excise invoice xxxx has already been posted for vendor xxxxx.
    Please help.
    Regards,
    Anil Bhamere

  • Need Help for Blackberry8700g

    I need help for Blackberry8700g, It is the error message Java.lang.outofmemory Error. I can not make even phone calls. After reset it is same message pop up and does not off the power jum error523 

    You are in line to wipe and reload the OS on the BlackBerry.
    Follow the directions here and you will be fine.
    http://www.blackberryfaq.com/index.php/How_do_I_wipe_the_BlackBerry_using_Jl_Cmder%3F
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • New update on my iTunes 8.2 computer. Sync my iPads on the computer missing playlist on my computer ??? Need help. Worst update ever   

    new update on my iTunes 8.2 computer. Sync my iPads on the computer missing playlist on my computer ??? Need help. Worst update ever   

    Hello there, dancingteacher.
    Removing and re-installing iTunes can be a challenging endeavor and has to be done in a very particular way. The following Knowledge Base article provides a clear, step-by-step process of removing iTunes:
    Issues installing iTunes or QuickTime for Windows
    http://support.apple.com/kb/ht1926
    The "Additional Troubleshooting" section also includes a link to updates and conflicts with software for your Windows Operating System as well.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • I have problem with buying in games , I got the massage that the purchased can not be completed , please contact iTunes support.. I need help for my case please

    I have problem with buying in games , I got the massage that the purchased can not be completed , please contact iTunes support.. I need help for my case please

    http://www.apple.com/support/itunes/contact/

  • Need help for Format HD

    Hi I need Help for Formating HD so Wat Key need hold on start up for format HD I apprciated you Help

    Jesus:
    Formatting, Partitioning Erasing a Hard Disk Drive
    Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
    • With computer shut down insert install disk in optical drive.
    • Hit Power button and immediately after chime hold down the "C" key.
    • Select language
    • Go to the Utilities menu (Tiger) Installer menu (Panther & earlier) and launch Disk Utility.
    • Select your HDD (manufacturer ID) in left side bar.
    • Select Partition tab in main panel. (You are about to create a single partition volume.)
    • _Where available_ +Click on Options button+
    +• Select Apple Partition Map (PPC Macs) or GUID Partition Table (Intel Macs)+
    +• Click OK+
    • Select number of partitions in pull-down menu above Volume diagram.
    (Note 1: One partition is normally preferable for an internal HDD.)
    • Type in name in Name field (usually Macintosh HD)
    • Select Volume Format as Mac OS Extended (Journaled)
    • Click Partition button at bottom of panel.
    • Select Erase tab
    • Select the sub-volume (indented) under Manufacturer ID (usually Macintosh HD).
    • Check to be sure your Volume Name and Volume Format are correct.
    • Click Erase button
    • Quit Disk Utility.
    cornelius

  • Need help for my requirement...

    Need help for my requirement...
    Hello Experts,
    I have report where users can input the company, housebank, account ID and posting date.
    Now in one column of my report named 'Cash in Bank', I need to get all postings from cash
    accounts with GL code ending in '0'. Now, I know that I can get the amounts in BSIS/BSAS
    but how do I link it with the proper bank and account?
    For example:
                       Cash in Bank
    Bank A
      Account ID 1     1,000,000
      Account ID 2     25,000,000
    Hope you can help me guys. Thank you and take care!

    hi Viraylab,
    each house bank you can find in table T012, in T012K you'll find the bank accounts to the housebank, the G/L account will be in T012K-HKONT.
    hope this helps
    ec

  • Need help for flash builder

    i need help for flash builder 4 and papervison 3d. I need to create a slider with it ranges of value from 10 to 50 to adjust the camera values for the camera.fov and also need to create it for the yaw of the object from 0 to 360. I try to look for any slider event and classes in this program but cant find any, btw, i need to use the AS only project file.
    here is my codes:
    can you please tell me how i should modify the codes?
    package
        import flash.display.BitmapData;
        import flash.display.Sprite;
        import flash.events.Event;
        import org.papervision3d.materials.BitmapFileMaterial;
        import org.papervision3d.materials.BitmapMaterial;
        import org.papervision3d.objects.primitives.Sphere;
        import org.papervision3d.view.BasicView;
        [SWF (width="800", height="600", backgroundColor="0x000000",frameRate="30")]
        public class EarthBitmap extends BasicView
            private var sphere:Sphere;
            public function EarthBitmap()
                super(800 , 600);
                var earthmaterial:BitmapFileMaterial = new BitmapFileMaterial("../assets/Earth.jpg");
                sphere = new Sphere(earthmaterial,100,20,18);
                camera.fov = 25;
                scene.addChild(sphere);
                addEventListener(Event.ENTER_FRAME,rotateSphere);
            public function rotateSphere(evt:Event):void
                sphere.yaw(0.2);
                singleRender();

    Turn the click handler into a full on separate function. Then store all the views in an array and use Math.rand() to randomly choose one.
    Something like this:
    <fx:Script>
         <![CDATA[
              var questionsArray:Array = {question2,question3,question5,questionRed,questionGeography};
              function buttonClickHandler(event:MouseEvent){
                   var randomProblem:int = Math.floor(Math.random()*(questionsArray.length));     //generates a random integer between 0 and the total number of questions in the array (arrays are 0-based)
                   navigator.pushView(questionsArray[randomProblem]);
         ]]>
    </fx:Script>
    <s:Button id="randomProblemButton" label="Next Problem" click="buttonClickHandler(event)" />
    Haven't tested that, but something along that line should work

  • Need help for importing oracle 10G dump into 9i database

    hi, Someone help me to import oracle 10G dump into 9i database. I'm studying oracle . Im using oracle 10G developer suite(downloaded from oracle) and oracle 9i database. I saw some threads tat we can't import the higher version dumps into lower version database. But i'm badly need help for importing the dump...
    or
    someone please tell me the site to download oracle 9i Developer suite as i can't find it in oracle site...

    I didnt testet it to import a dump out of a 10g instance into a 9i instance if this export has been done using a 10g environment.
    But it is possible to perform an export with a 9i environment against a 10g instance.
    I am just testing this with a 9.2.0.8 environment against a 10.2.0.4.0 instance and is working so far.
    The system raises an EXP-00008 / ORA-37002 error after exporting the data segments (exporting post-schema procedural objects and actions).
    I am not sure if it is possible to perform an import to a 9i instance with this dump but maybe worth to give it a try.
    It should potentially be possible to export at least 9i compatible objects/segments with this approach.
    However, I have my doubts if this stunt is supported by oracle ...
    Message was edited by:
    user434854

  • Need Help for Nokia 6500 slide

    Hi all I'm A new Guy here ,
    But I do really need help for hard reset my phone
    I already try *#7073# But It doesn't work ,
    If Anybody know to make a hard reset please help

    rwss wrote:
    I'v got te same problem with my 6500 Slide, is there a button combination that we have to press
    to hard reset the 6500 Slide?!
    How does the 6500 slide hard reset?
    That's simple.
    All you have to do is:
    From MENU goto SETTINGS, When there scroll down and select 'Restore Factory Setting'.
    There are two options in there:
    "Restore Settings only"
    and
    "Restore all"
    Select "Restore All"
    When done the phone will delete every thing on the Phone memory(C:\)(contacts,picture,messages etc)
    and also restore phone to its original settings and will restart.
    This proceedure is mostly common on S40 phone.
    Hope this explain and solve the problem.

  • Need help for publishing web intelligence document (universe) into InfoView

    Post Author: mirage
    CA Forum: Publishing
    Hello all,
    I need help for publishing web intelligence document (universe) into InfoView.
    can't find this information in Business Objects Designer's Guide and in Business Objects Administrator Guide.
    Can somebody give short instructions how can I do it?
    Regards, Slava

    If the change between the 2 types of data has to happen dynamically during run time them
    1. Use 2 dataproviders
         a. Current
         b. Historic
    2. Merge the 2 dimensions
    3. Use Webi variable to switch between the measure of the current and historic universe
    Ex  if [year] < 2010 then historic.[expense] else current.[expense]
    Hope this helps,
    Divya

Maybe you are looking for