Need to repair MBR - L505D-S5983
Can I get to the Windows 7 Recovery Console by booting to the Recovery Disk that I made after unpacking and setting up my L505D-S5983? I do not need to run a full recovery. I have installed Linux on the laptop and want to remove it. The laptop boots into Windows 7 OK from Grub but I can not boot into Linux.
Satellite L550-ST2743
Here's a Win 7 recovery disk that will hopefully do the trick.
Yes, that will work. Follow these instructions.
When you reach the System Recovery Options menu, open a Command Prompt, and enter this.
bootrec /fixmbr
That will write Microsoft's MBR to the first sector of the disk. (It will not overwrite the partition table.) See KB927392.
-Jerry
Similar Messages
-
No Audio or USB Ports after Recovery on Satellite L505D-S5983
I have recently done a system recovery with disks I created when I originally got my Satellite L505D-S5983. Which put the laptop back to an "out of the box" state...supposedly... I have been asking on a Microsoft forum for help with my problems, with limited luck.... It is still not working. I'm pasting my original posts here hoping that maybe somebody on here can help me.
POST 1:
My Toshiba Satellite L505D is running 32-bit Windows 7 Home Premium. After about 4 months of downtime I recently started it back up. There were roughly 37 updates to install when I turned it on, as expected. The updates were downloaded and installed, but when the system was restarted the system froze as soon as the desktop loaded. I booted multiple times and every time it completely freezes immediately after start up. I am not even able to open the task manager (ctrl+alt+del). They system boots perfectly fine in safe mode, and I ran what diagnostics I could find and nothing shows up....according to Windows everything is fine.
After Going through this multiple times, I got sick of it and decided to do a system recovery. Not a system RESTORE...it was a system RECOVERY. The HDD was completely wiped, and the system was supposedly returned to its original form as it was out of the box. Getting my hopes up as it finished its process... The system worked fine through the initial setup (language, time, etc.) and then as soon as the desktop loaded it froze again!
So here I am with a completely wiped HDD (except for the factory toshiba software), and a Windows OS that will only work in safe mode... I would like to avoid reinstalling Windows, I don't have any disks or anything. So any help would be appreciated
P.S. let me elaborate on what I mean by "froze". The system is completely non-responsive. No cursor movement at all, touchpad, keyboard, USB ports, nothing. When I did the restore the cursor, touchpad and keyboard worked through the initial settings only. Even when the desktop is loading i get movement for a second or two before everything freezes.
REPLY I RECIEVED:
Hi,
Since the computer is working in safe mode, I would suggest you to start the computer in clean boot to check which third party program is causing the issue. To configure your computer to clean boot follow the link
http://support.microsoft.com/kb/929135
Note: After you have finished troubleshooting, follow step 7 in the article to boot to normal startup.
If the issue does not persist in clean boot then refer ‘Step 3’, ‘step 4’ and ‘step 5’ from the following link to narrow done the issue and find out which service or startup item is causing the issue.
MY RESPONSE POSTING MY CURRENT ISSUE:
Thank you, and yes that's exactly what it was. It turned out to be an ATI program for my AMD graphics card that was not installed properly. It makes me wonder if I had to do the recovery in the first place lol.
However now I have a whole other issue. Windows is now telling me that "No audio output device is installed".....
In device manager the yellow "!" is there (High Definition Audio Controller), it tells me that it is not working....yet it says that the best drivers are installed! So yeah...I have no audio now. The only info windows gives me for the sound card is that it from Microsoft... with a driver version of 6.1.7601.17514....which naturally doesn't really help me since I have no idea what card or mobo I have . Is there any way for me to find out what I need other than opening up my laptop?
//--> Toshiba Satellite L505D-S5983_AMD Athlon II Dual-Core M300 2.00 GHz_3GB RAM 32-bit OS <--//
RESPONSE FROM SOMEBODY ELSE:
Hi,
Check with Toshiba Support, their on-line documentation and drivers, and ask in their
forums about known issues.
Toshiba - Forums
http://laptopforums.toshiba.com/
Toshiba - Contacts
http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/navShell.jsp?cf=su_contact
Toshiba - Drivers - navigate to your model
http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/home.jsp?nav=Download
Toshiba - Support
http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/home.jsp
========================================
First run SFC /scannow and checkdisk (chkdsk) as the cause of these issues might
be some sort of corruption.
Start - type in Search box - CMD find at top of list - RIGHT CLICK - RUN AS ADMIN
sfc /scannow
How to Repair Windows 7 System Files with System File Checker
http://www.sevenforums.com/tutorials/1538-sfc-scannow-command-system-file-checker.html
Then run checkdisk (chkdsk).
How to Run Disk Check in Windows 7
http://www.sevenforums.com/tutorials/433-disk-check.html
Then use this troubleshooter :
References to Vista also apply to Windows.
Fixing a customer problem: “No Audio Device is Installed” when launching sndvol on Windows Vista
http://blogs.msdn.com/b/larryosterman/archive/2009/01/06/fixing-a-customer-problem-no-audio-device-i...
Also update or re-install the driver.
Control Panel - Device Manager - SOUNDS - look for HD Audio - Mine says RealTek High
Definition Audio (that is an example and yours may have an entirely different name/maker).
Write down description make and model - double click on it - drivers tab - write down version.
Now Click UPdate Drivers which may not do anything as MS is far behind certifying drivers.
Then RIGHT CLICK on it and UNINSTALL - REBOOT - this will rebuild the driver stack.
1st go to system maker's site and look for latest driver Download - SAVE - go to right click on
and RUN AS ADMIN (This is your fallback.) REBOOT after each driver installation.
NOTE : Sound drivers often rollback so check the version after installation and the
reboot to see if the version you installed is there, if not repeat the install - reboot
until it is. It can take several tries depending on how many rollbacks it does.
Then do same for Device Maker's site.
Manually look at manufacturer's sites for drivers - and Device Maker's sites.
http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm
Installing and updating drivers in Windows 7 (updating drivers manually using the methods above
is preferred to ensure the latest drivers from System maker and Device makers are found)
http://www.sevenforums.com/tutorials/43216-installing-updating-drivers-7-a.html
Error “the Audio Service Is Not Running” When Opening the Volume Mixer in Vista
http://www.winhelponline.com/blog/error-the-audio-service-is-not-running-when-opening-the-volume-mix...
Also Right Click Speaker near clock - Playback Devices - right click in the box area -
check Show disable and disconnected devices. Highlight speaker and on the lower
Right click Properties check settings for Device Usage enabled and so on. Also do
same for Configure on Lower Left of that box.
In Control Panel you can also look for an Audio Manager along with the Sound Settings.
Open the Playing Audio troubleshooter
http://windows.microsoft.com/en-us/windows7/Open-the-Playing-Audio-troubleshooter
Problems with sound and audio or no sound - a Mr Fixit
http://support.microsoft.com/gp/no_sound
No sound in Windows
http://windows.microsoft.com/en-us/windows/help/no-sound-in-windows
Tips for fixing common sound problems
http://windows.microsoft.com/en-us/windows7/Tips-for-fixing-common-sound-problems
Speakers and other audio output devices
http://windowshelp.microsoft.com/Windows/en-US/Help/a43f3a31-6d9f-49d1-be22-e2f47b8b1f2c1033.mspx
How to Enable Hidden Audio Devices in Vista
http://www.vistax64.com/tutorials/143447-audio-device-enable-hidden-devices.html
Hope this helps.
===========================================================================================
Ok...so I have installed all of the appropriate drivers that I thought I may need from this website. I have tried ALL of those system analysis programs that were suggested. Every one of them lists my mobo simply as a Toshiba motherboard, with no audio card information. Which I'm assuming that is because it has an internal sound processor. My problem is that none of the properties, or ANYTHING I try, will give me information on what I need to fix this...
I would be more than willing to run the recovery again if I knew that I had everything I actually need... When I created my original recovery disks it created a third disk with "apps and drivers". I installed all of them...and still here I am... And I haven't even STARTED on my USB port issue yet...those don't work either, and they don't even show up in my Device Manager...sigh...
And please, a response that doesn't look like an automated response to try and sell software like the last one I recieved from the Microsoft forum would be appreciated
Thank you for your time, and apologies for the lengthy post, but I wanted to provide as much info as possible.Satellite L505D-S5983
I would try another restore of the hard disk to its original out-of-the-box contents using Toshiba recovery media. Maybe something went wrong in the process. Make sure everything works before applying any updates and adding any hardware or software.
Then add things carefully, rebooting Windows and testing the USB and audio at each step.
Please note this.
The only info windows gives me for the sound card is that it from Microsoft... with a driver version of 6.1.7601.17514....which naturally doesn't really help me since I have no idea what card or mobo I have . Is there any way for me to find out what I need other than opening up my laptop?
Every one of them lists my mobo simply as a Toshiba motherboard, with no audio card information. Which I'm assuming that is because it has an internal sound processor. My problem is that none of the properties, or ANYTHING I try, will give me information on what I need to fix this...
All of the latest drivers for your model are easily found here. This one is for the sound.
Realtek Audio Driver for Windows 7 (32/64)
-Jerry -
Volume Control Issue (Satellite L505D-S5983)
My laptop: Toshiba Satellite L505D-S5983
So here's the issue:
Just recently I've started having problems using my volume control located next to the SD card reader slot.. You know, the volume 'slider'. It's been acting rather strangely, when I try to adjust my volume it doesn't change at all from the current volume percentage that it's at... Even when I'm sliding the slider. So then, I have to go into the manual volume in my hidden icons menu to change the volume. However, after I go through this step, I am then able to use my volume 'slider' control, and it actually works.
So, I'd like to know:
A) Why this is happening?
B) Am I able to fix this issue?
C) How would I fix this issue?
ox♥Scairry♥xoStill in need of a response.
ox♥Scairry♥xo -
L505D-S5983 Volume Control Wheel
I have a Satellite L505D-S5983 that I received for Christmas. The Volume Control Wheel on the front edge of the laptop turns freely and does not seem to affect the speaker volume. Is this normal or does it require repair or replacement?
Dave
Solved!
Go to Solution.n8oay wrote:
Found it. Now I am getting acceptable sound out of it...not good enough for movies or CDs, but it is definitely better than the 7 year old Systemax/Mitac it replaces
The low DVD and CD audio is frustrating. Had problems ever since I bought my L505 series laptop late last year trying to listen to DVD movies. There's a thread about this in the Sound forum where others have low DVD audio output, but no real solution to the issue. The only workaround for these low audio issues seems to be enabling "Loudness Equalization" on the Realtek HD Audio Manager (or Speaker Properties setting) and then using a headset or external speakers to watch a DVD move. There is definitely a problem that has so far been unacknowledged by Toshiba, with either the hardware or with the sound drivers as my previous Toshiba laptop didn't have this low sound problem on DVD movies and audio CD's. -
Various problems with Satellite L505D-S5983
After getting a virus on my laptop I simply decided it would be best to reset the computer to factory settings.
So I pressed restart, then F8, and following that I followed the steps to factory reset my laptop.
Though it took the laptop about 15 hours to restart and reload everything? (I didn't do any kind of recovery, so it's as if I just took it out of the box, it did it's thing where it loaded it for the "first use")
So obviously I had to get some sleep within that 15 hours I had done this reset at night, so I wasn't aware of what it was doing? When I got on it the next morning it had finished the process for the first use. Then something went wrong when I had been on it and it froze so I turned it off. When I turned it back on it kept trying to do the "first use" process again.
Then at some point it stopped. So I was able to connect to the internet and download google chrome and such.
Then more problems became evident.
The first one being the font is blurry. Now I'm not sure if it's because the screen is rectangular as opposed to monitor I'm currently using which is square.
The next one is a little more aggrivating, whenever I try to log on on its regular mode, I'll click on my account (the admin account, the only account on the laptop.)
When I click on it, it tells me that my accound has been disabled and that I need to contact the system admin - which I thought I was.
So now, after going through my user accounts when I'm on safe mode with networking, I can't find anything to fix that.
So now, apparently I've gone on safe mode too frequently where if I try to open chrome, my blue screen pops up indicating a crash, and it restarts.
So hopefully this is all fixable?
Thank you for the help.Satellite L505D-S5983
If it is taking that long to recover and you still have issues I would use your recovery media that you should make if you have not did so already. As Toshiba suggest it is best to make the recovery media when the laptop is new because it can become infected by a virus just like your main operating system.
You should not interrupt the recovery, meaning keep power supply plugged in and don't force a restart. If something happened to interrupt the recovery you can just recover to factory settings again except use the copy you previously made.
If you still have issues you may have other problems.
Satellite L505D-S5983 support page is here - http://support.toshiba.com/support/modelHome?freeText=2439388
The user guide and available info and drivers are located there.
If you need to order recovery media get it here- http://support.toshiba.com/recovery#media
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!**** -
Stuck: Need Disk repair but DVD drive dead and only have USB 1
[1 Ghz flat-panel iMac with USB 1 ports (no USB 2) and also Firewire 400]
I noticed a strange discrepancy (small but concerning) between the size of a folder on hard drive (folder of all mp3's with no subfolders) and the backup of the same folder on a mounted thumb drive.
(The size difference was not due to any invisible .DS_Store files and both folders are displayed in List view format.)
Disk Utility reports three things:
1. Incorrect number of thread records
2. Volume Bit Map needs minor repair
3. Checking volume information.
Volume free block count",0) [I might have mangled this line]
(It should be 13438611 instead of 13437937)
Here is the GOOD (but these are useless as explained under the "Bad"):
- I have a Tiger 10.4 boot DVD for a repair ==>but see below
- I also have a Disk Warrior disk (never used)
Here is the BAD:
- My built-in optical drive [Pioneer DVD-RW DVR-105] is -- I now discover - defunct and DEAD - it does not run the Tiger Boot DVD (in pristine shape).
- I bought an external SuperDrive (unopened) but I believe no boot from USB 1 is possible in PowerPC so a SuperDrive with USB 1 is useless.
Questions:
1.) Is there any way to boot from some external source (optical drive is DEAD) to run Disk Utility and/or Disk Warrior? -- I see none in this case! (gulp).
2.) More importantly (and this is my fundamental concern): Do the three Disk Utility hard drive issues constitute any direct threat to the integrity of my files?
I have almost everything backed up to duplicate thumb drives over these many months as standard practice.
Are these Disk Utility errors fully isolated to hard drive directory-keeping...or do these directory damage errors pose the possibility of mangling or harming my files or their metadata (filesize, etc.).
Put another way, when files are backed-up from a hard drive under the Disk Utility reports above, do they remain unharmed and undamaged by the situations reported by Disk Utility?
Thanks,
BillJeff and Michael,
Thank you both for your generous and thoughtful input.
Michael: As I slept on it overnight, the exact same idea occurred to me of trying a Target Mode to the iMac from my Lion MacbookPro (I have it but stupidly have yet to use it much!).
I did buy a Firewire 800 (MBP) to Firewire 400 (iMac) adapter cable a few months ago!
CONCERN: Would there be potential compatibility issues or risks in running Lion 10.7's Disk Utility against the hard drive of the old OSX 10.4 iMac in Target Disk Mode?
==> Assuming an "it's ok" answer to the Target Disk question, would the majority of users agree that the Target Disk Mode would be more prudent than running:
fsck -fy in Single User Mode
I have never done fsck -fy before especially because I was under the impression there were issues with Journaled drived but from what I have read today...it looks ok to do)
Jeff: Can't thank you enough for the reference to the OTW DVD drive. I might first invest $10 in one of those DVD lens cleaner disks that I've read about. It's probably not the issue or else why would the drive read commercial Music cds perfectly well!
Thanks,
Bilil -
I have iPhoto 11, version 9.4.1 installed. When my library upgraded, I got a message that the photos couldn't be inported and I need to repair iPhoto permissions. How do I do that? My photos are there, but I can no oonger drag them to the photo stream.
Disable Photo Stream in iPhoto's preferences and then go back and reenable it. See if that will jump start the process. If that doesn't help try this: make a temporary, backup copy (if you don't already have a backup copy) of the library and try the following:
1 - delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your
User/Home()/Library/ Preferences folder.
2 - delete iPhoto's cache file, Cache.db, that is located in your
User/Home()/Library/Caches/com.apple.iPhoto folder.
Click to view full size
3 - launch iPhoto check its preferences to meka sure all is as you expect and try again.
NOTE: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding down the Option key when launching iPhoto. You'll also have to reset the iPhoto's various preferences.
NOTE 2: In Lion and Mountain Lion the Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
OT -
i have a slow macbook, i ran live disk utilities (from hard drive), turned out I needed to repair disk from a installation disk. Did that, I got the volume (Hard drive) repaired from the installation disk disk. To this point, great!
When I reboot from hdd, then run disk utility, I get the same error message i did b4 repair. I went thru two rounds of this.....
Can anyone help? thanksSorry guys, I don't see how to reply to you so I use reply to "me" basically.
So the error I get is "volume header needs minor repair" and then you need to perform repair from the installation disk message.
I did repair not verify from the disk twice. Every time ending in the "the volume had ha been successfully repaired". Then I reboot from the internal disk. Run disk utilities from it, do verify and get the same error message I got before repair. I hope this can shed some light fr you guys. Sorry I didn't include details in the original
MEssage. -
Need help repairing Driver - pic included.
Hey guys, i have been trying to get boot camp to work on my macbook for ages. First i got it to work, but then when i used windows, it wouldn't recognize my wireless in my macbook. Anyways, to make a long story short, i used the boot camp assistant tonight to delete the windows partition, then i was trying to re-install windows XP.
As most of you know, the first step is to partition the disks, when i told it how much to partition of each it came up with a driver error saying i needed to repair the disks.
so, i went to disk utility to try and verify the disk, its did, but then it came up with this:
http://i50.photobucket.com/albums/f344/kawirider04/Untitled-1-1.jpg
any help would be great guys, i eventually want to run windows xp on my blackbook so i can play World of Warcraft with a higher framerate. Anyways, thanks in advance!
BTW - after i 'verify disk' i can't click on 'repair disk'
Black Macbook 1gb Ram Mac OS X (10.4.8)Boot up from your Install DVD and then launch Disc Utility to verify/repair the disc and permissions as well.
-
Unable to boot from install disk for needed disk repair
Hi- I need to repair my disk, but haven't been able to boot from the DVD. When I've tried (several times), I get a black screen with a long error message, ending in something like "hanging here." Any advice?
Thanks,
LauraThat is a kernel panic. Kernel panics on startup from an installer disc mean one of two things usually: 1. You are using an installer disc with an OS version that is not able to boot the computer model you have. Usually the version is too early for the model; 2. There's a serious hardware problem such as a dead hard drive or motherboard problem.
-
After giving my account all access privileges to its home folder including the folders within, I was able to get my desktop picture back, I could see the computer icon on the screen, and the annoying never ending "OS 10 needs to repair your library. Type in a your password..." message went away.
Now I can't use my mail functions. How could Apple have released this OS system? HELP.
In Mail, it asks for a Keychain password-one that i don't use here at my job, and then it doesn't allow you to type anything. I don't have such an account anyway.
I know there is an update 10.9.3, but I'm afraid of jumping out of the frying pan into the fire. Will the update address these issues?Try two things just to make certain that there are no problems with your hard drive. Do you have your original install disc that came with your Mac? If so boot from it and run Disk Utility to both verify and repair permissions. Then verify your hard drive - if errors are found, repair them.
Note that this may not fix your problem, but it will eliminate a corrupt disk.
Clinton -
Internal Microphone not working for L505D-S5983 (PLEASE HELP!)
Hi,
I can't seem to get my internal microphone to work. I have enabled it under Sound->Manage Audio Devices
->Recording tab. However the green vertical bar does not detect any voice. After setting the Microphone boost to +40dB, it detected some noise (since it has some green light) but I realized it wasn't detecting my voice. Since this did not work, I re-set the Microphone boost to only +10dB. I only have one internal microphone and no external microphone.
I have seen many postings on internal microphones not working on Toshiba laptops but couldn't find a solution to mine. Can someone please help? I think it's about time that Toshiba fix this issue after the countless complaints.
FM.No mentions of reinstalling the sound driver. That sometimes turns on the microphone.
Satellite L505D-S5983
Realtek Audio Driver for Windows 7 (32/64)
Satellite L505-S5988
Realtek Audio Driver for Windows 7 (32/64)
Satellite M500-ST6421
Realtek Audio Driver for Windows Vista (32bit/64bit)
-Jerry -
I need to repair a Macbook Pro with Disk Utility using target mode connected to my iMac. Can I use ethernet cable to connect them or must it be firewire?
Firewire
-
Need to repair HD before installing mavericks HELP !!
Dear all,
I have a perfectly working MacBook Air, built 2012 with 256 GB.
Mountain Lion does a great job, but I want to progress to Mavericks.
As advised, I ran disk Utility system check and this came up at veryfying disk:
Volume bitmap needs minor repair for orphaned blocks
Invalid Volume free block count
The Volme MA_HD was found corrupt and needs to be repaired
As advised I restart holding the command-R combo after which my computer starts to connect to the Internet searching for the boot-tool. then after about 30 seconds, I get a warining sign with apple.com/support - 1007F.
When I am on another network, the Internet logo keeps spinning for 20 minutes and then I get a -2007F failure.
I can not repair my disk it seems, although all is working fien.
Quickly made a Time Machine backup, but what can i do next ?
thanks for your help !!Same thing: Internet logo spinning for 10 seconds, then apple.com/support -100F.
In the meantime the computer works perfect under Mountain Lion. -
Random Kernel Errors and need to repair disk
After trying to partition for Bootcamp, the computer locked into a Kernel error. I went to validate the disk and discovered that I need to repair the disk. I have tried booting from my OSX installation disk to access the repair disk functionality. I receive a kernel error each and every time I try to boot from disk. Details as follows - please advise.
Interval Since Last Panic Report: -1127922 sec
Panics Since Last Report: 1
Anonymous UUID: F32AB6E4-83EA-45BF-9186-E23B077676E9
Sun Mar 13 21:26:16 2011
panic(cpu 1 caller 0x2a6ac2): Kernel trap at 0x581571fc, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0x00000018, CR3: 0x19703000, CR4: 0x00000660
EAX: 0x00000000, EBX: 0x00000000, ECX: 0x00000000, EDX: 0x06f75004
CR2: 0x00000018, EBP: 0x5786bc78, ESI: 0x07f29c00, EDI: 0x07f29c00
EFL: 0x00010246, EIP: 0x581571fc, CS: 0x00000008, DS: 0x00290010
Error code: 0x00000000
Backtrace (CPU 1), Frame : Return Address (4 potential args on stack)
0x5786ba88 : 0x21acfa (0x5ce650 0x5786babc 0x223156 0x0)
0x5786bad8 : 0x2a6ac2 (0x590a50 0x581571fc 0xe 0x590c1a)
0x5786bbb8 : 0x29c968 (0x5786bbd0 0x7f16700 0x5786bc78 0x581571fc)
0x5786bbc8 : 0x581571fc (0xe 0x48 0x10 0x57860010)
0x5786bc78 : 0x580fbfb8 (0x0 0x7f16700 0x80deac0 0x810b140)
0x5786bc98 : 0x57d10189 (0x7f29c00 0x57d15304 0x80deac0 0x0)
0x5786bd08 : 0x57d0cb98 (0x7f29c00 0x5786bdcc 0x7501bb8 0x4a7632a3)
0x5786bd38 : 0x5330cf (0x7f29c00 0x7501bb8 0x7501bb8 0x0)
0x5786bd88 : 0x563a86 (0x7f29c00 0x7501bb8 0x7501bb8 0x0)
0x5786bde8 : 0x284883 (0x7f29c00 0x7501bb8 0x0 0x0)
0x5786be58 : 0x21d09c (0x6f00168 0x6f00284 0x6f0016c 0x6f001a4)
0x5786be98 : 0x210234 (0x6f00100 0x5786bedc 0x739bd74 0x5786bed0)
0x5786bef8 : 0x216497 (0x6f00100 0x0 0x0 0x0)
0x5786bf78 : 0x2922ba (0x74407e8 0x0 0x0 0x0)
0x5786bfc8 : 0x29d44d (0x74407e4 0x0 0x10 0x74407e4)
Kernel Extensions in backtrace (with dependencies):
com.apple.NVDAResman(6.0.0)@0x580f8000->0x5838bfff
dependency: com.apple.iokit.IOPCIFamily(2.6)@0x50e3b000
dependency: com.apple.iokit.IONDRVSupport(2.0)@0x57cbd000
dependency: com.apple.iokit.IOGraphicsFamily(2.0)@0x57cff000
com.apple.iokit.IOGraphicsFamily(2.0)@0x57cff000->0x57d1cfff
dependency: com.apple.iokit.IOPCIFamily(2.6)@0x50e3b000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
10A432
Kernel version:
Darwin Kernel Version 10.0.0: Fri Jul 31 22:47:34 PDT 2009; root:xnu-1456.1.25~1/RELEASE_I386
System model name: MacBook7,1 (Mac-F22C89C8)
System uptime in nanoseconds: 147336336486
unloaded kexts:
(none)
loaded kexts:
com.apple.driver.InternalModemSupport 2.6.0
com.apple.driver.AppleTyMCEDriver 1.0.1d8
com.apple.driver.AppleIntelYonahProfile 14
com.apple.driver.AppleIntelPenrynProfile 17
com.apple.DontSteal_Mac_OSX 7.0.0
com.apple.driver.AppleHDA 1.7.4a1
com.apple.driver.AppleGraphicsControl 2.8.16
com.apple.driver.AppleIntelNehalemProfile 11
com.apple.driver.AudioIPCDriver 1.1.0
com.apple.driver.AppleUpstreamUserClient 3.0.5
com.apple.driver.SMCMotionSensor 3.0.0d4
com.apple.driver.ACPISMCPlatformPlugin 3.4.0a20
com.apple.driver.AppleBacklight 170.0.2
com.apple.driver.AppleIntelMeromProfile 19
com.apple.GeForce 6.0.0
com.apple.driver.DiskImages.SparseDiskImage 281
com.apple.driver.DiskImages.ReadWriteDiskImage 281
com.apple.driver.DiskImages.UDIFDiskImage 281
com.apple.driver.DiskImages.RAMBackingStore 281
com.apple.driver.DiskImages.HTTPBackingStore 281
com.apple.driver.DiskImages.FileBackingStore 281
com.apple.driver.AppleUSBTCButtons 1.8.0b4
com.apple.driver.AppleUSBTCKeyEventDriver 1.8.0b4
com.apple.driver.AppleUSBTCKeyboard 1.8.0b4
com.apple.iokit.SCSITaskUserClient 2.5.0
com.apple.BootCache 31
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.driver.AppleUSBHub 3.7.8
com.apple.driver.AirPortBrcm43xx 410.91.20
com.apple.nvenet 1.0.58
com.apple.driver.AppleUSBOHCI 3.7.5
com.apple.driver.AppleUSBEHCI 3.7.5
com.apple.iokit.IOAHCIBlockStorage 1.5.0
com.apple.driver.AppleEFINVRAM 1.3.0
com.apple.driver.AppleAHCIPort 2.0.0
com.apple.driver.AppleRTC 1.3
com.apple.driver.AppleHPET 1.4
com.apple.driver.AppleSmartBatteryManager 160.0.0
com.apple.driver.AppleACPIButtons 1.3
com.apple.driver.AppleSMBIOS 1.4
com.apple.driver.AppleACPIEC 1.3
com.apple.driver.AppleAPIC 1.4
com.apple.driver.AppleIntelCPUPowerManagementClient 90.0.0
com.apple.security.sandbox 0
com.apple.security.quarantine 0
com.apple.nke.applicationfirewall 2.0.11
com.apple.driver.AppleIntelCPUPowerManagement 90.0.0
com.apple.driver.AppleProfileReadCounterAction 17 - last loaded 147290710663
com.apple.driver.AppleProfileTimestampAction 10
com.apple.driver.AppleProfileThreadInfoAction 14
com.apple.driver.AppleProfileRegisterStateAction 10
com.apple.driver.AppleProfileKEventAction 10
com.apple.driver.AppleProfileCallstackAction 20
com.apple.iokit.IOSurface 73.0
com.apple.driver.AppleHDAPlatformDriver 1.7.4a1
com.apple.iokit.IOBluetoothSerialManager 2.2f18
com.apple.iokit.IOSerialFamily 10.0.2
com.apple.driver.AppleHDAHardwareConfigDriver 1.7.4a1
com.apple.driver.DspFuncLib 1.7.4a1
com.apple.iokit.IOAudioFamily 1.7.0fc16
com.apple.kext.OSvKernDSPLib 1.3
com.apple.driver.AppleHDAController 1.7.4a1
com.apple.iokit.IOHDAFamily 1.7.4a1
com.apple.driver.AppleSMC 3.0.1d2
com.apple.driver.IOPlatformPluginFamily 3.4.0a20
com.apple.iokit.AppleProfileFamily 40
com.apple.NVDAResman 6.0.0
com.apple.iokit.IONDRVSupport 2.0
com.apple.iokit.IOGraphicsFamily 2.0
com.apple.driver.DiskImages.KernelBacked 281
com.apple.driver.AppleUSBMultitouch 200.20
com.apple.iokit.IOUSBHIDDriver 3.7.5
com.apple.driver.BroadcomUSBBluetoothHCIController 2.2f18
com.apple.driver.AppleUSBBluetoothHCIController 2.2f18
com.apple.iokit.IOBluetoothFamily 2.2f18
com.apple.driver.AppleUSBMergeNub 3.7.5
com.apple.driver.AppleUSBComposite 3.7.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice 2.5.0
com.apple.iokit.IOBDStorageFamily 1.6
com.apple.iokit.IODVDStorageFamily 1.6
com.apple.iokit.IOCDStorageFamily 1.6
com.apple.driver.XsanFilter 402.1
com.apple.iokit.IO80211Family 300.20
com.apple.iokit.IOUSBUserClient 3.7.5
com.apple.iokit.IONetworkingFamily 1.8
com.apple.driver.AppleFileSystemDriver 2.0
com.apple.iokit.IOUSBFamily 3.7.8
com.apple.iokit.IOAHCISerialATAPI 1.2.0
com.apple.iokit.IOSCSIArchitectureModelFamily 2.5.0
com.apple.iokit.IOAHCIFamily 2.0.0
com.apple.driver.AppleEFIRuntime 1.3.0
com.apple.iokit.IOHIDFamily 1.6.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.TMSafetyNet 6
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.DiskImages 281
com.apple.iokit.IOStorageFamily 1.6
com.apple.driver.AppleACPIPlatform 1.3
com.apple.iokit.IOPCIFamily 2.6
com.apple.iokit.IOACPIFamily 1.3.0The installation DVD is from another Mac, but is also Mac OSX 10.6
Is it required that I use the exact disk that shipped with my computer? (Go figure, it's in Minneapolis, I'm in Atlanta...).
The DVD however is in no way scratched or dirty. I will run the hardware test and report back.
Thank you for the leads.
Maybe you are looking for
-
SM:EXEC SERVICES job getting failed in Solution manager
HI All, SM:EXEC SERVICES job getting failed in solution mnager and job log will be fowlloing: 01-31-2012 19:09:21 Job started 01-31-2012 19:09:21 Step 001 started (program RDSMOPBACK_AUTOSESSIONS_ALL, variant , user ID BASISUSER) 01-31-2012 19:09:21
-
Another Customer Service Compla
Hi, and thank you for reading this message. I've experienced bad customer service from Creative and feel it necessary to add to the other warnings posed in this forum. The basic theme is the same: Creative seems to take deliberate steps to make recei
-
Video out on ipod nano 7th generation
I am trying to determine if I can play video out to TV with the latest ipod nano (7th gen). I found a support page( iPhone, iPad, iPod: TV out support) which suggests its possible from 3rd gen onwards but I'm not sure that page is up to date for 7th
-
JDeveloper EJB Class Editor lock
I created an EJB using JDev and used the EJB class editor to build the fields/methods in the bean. After working on the EJB for quite a while I reopened the EJB Class editor and found a blue error at the bottom of the window stating : Editor locked :
-
[urgent] D4O-1014 error when connecting to OracleBI Discoverer
Hi everyone, I try many approaches even remove all dimensions and cubes, still has the error msg when connecting to OracleBI Discoverer Version 10.1.2.2. Oracle Database is 9.2.0.7.0 D4O-1014: An unknown exception had occurred while connecting to the