Network card problem with Mobo make the computer crazy!!!

Im using a msi 745 Ultra version 10/cpu xp2400/basic graphics card/40gb HD, 256mbs of drr
I have tryed 2 networks cards both with the same results & even changed mobo & ram/graphic card/HD.
The computer seems to work fine untill i decide to put in a NIC.
It starts to post the wrong processor speed/screen decides not to display sometimes & takes a little longer to boot into windows. It will also some time crash when i turn on the computer. If i try to save something in the bios it will then reboot & then try to boot of the floppy drive.HD / CDrom drive but will not find them.This has happend on both mobos.
This is a very odd problem im getting need some help ASAP.

Sorry Bakes...folks aren't just waiting arount to help you. Expecting an answer in 2 hours is placing to high of an expectations on a user to user help forum.
No one here works for MSI, we are all users, just like you.
If you have not seen a reply, then there are several reasons that may affect why there has been no reply.
No one knows, or can offer o good answer to you question.
The question is too general and you did not supply the necessary information someone might need to even begin helping you. I have provided the basics on what we need at the top of this forum.
No one may be familiar with your motherboard's chipset, perhaps someone is but they have not visited the forum lately.
I can give only some general tips to consider for the time being.
Some incompatabilities may exist with a certain NIC card.
Check PCI slot IRQ sharing conflicts. Typically I stay to the middle slots and avoid the first and last. You may have to power down, move the card to another slot, and power back up. Each time checking your IRQ's in either Device Manager or System Information to see that the card is on its own IRQ.
Improper BIOS settings can cause conflicts.
Try "Plug and Play Aware OS" set to "No" and let the BIOS manage things or set it to yes and let Windows do it. In most cases it has been recommended to be set to no.
Upon installation of new hardware the setting "Reset Configuration Data" can be useful in avoiding lockups after POST due to conflicts recognized during "Verifying DMI Pool Data"
Possible reasons: Hardware change, BIOS settings change, improper connection of IDE cables, corrupt MBR (Master Boot Record) of the HDD (Hard Disk Drive), defective HDD or defective mainboard.
Possible causes: Hardware incompatibility, virus attack, electric circuitry damage/defect, corruption of data, improper BIOS settings, over-clocking damage.
*NOTE* Some Chipsets do not support this feature, see manufacturers documentation.
That's about all I care to share for now.
Good luck........

Similar Messages

Integrated Network card problem with K7N2 Delta-L

my integrated network card doesn't recognize any RJ45 cable bluged to it !!!
"ofcourse i enabled it from Bios"
the card is identefied by windows normally as nVidia ethernet ......
i tried to change the version of nForce driver but no way.
i pluged a normal PCI network card and work well with the LAN ... unpluged & re connect the integrated one with same cable but no way .. the task bar icon told me that A CABLE IS UNPLUGED >>
plz help

hi
what do you tru to connect it to?
i cant use onboard lan with my cable modem but a friends router worked without trouble.
btw welcome to this forum
bye

VIA KT400 Network Card Problems!

I've read allot about the problems I've been having and done many searches on Google and it all seems to come down to this: ALL VIA Motherboards in the KT400 series(and many other chipsets) lock up when using ANY Wireless Card\Usb Adapter. The frusterating part is nobody seems to have a clear answer on how to fix this or if it's even fixable
The forum linked down below tries to claim this only happens with Linksys cards.. This is false as I have a Microsoft Wireless G USB adapter and the EXACT SAME thing happens to me.
The strange part is if you are just browsing the web and reading text, everything works 100% fine. But as soon as you do something that uses DirectX or 3D Acceleration, like say Streaming Videos.. it freezes with the mouse curser just sitting there and I must hard reset the system.
Does anyone out there know of ANY kind of fix? I'm dying to know.
You can view someone elses post referring to the exact problem I have in the VIA Arena Forum
AMD Athlon XP 2500+ @ 2.00 Ghz
512 MB Ram
GeForceMX 5900XT
Antec 420 Watt Power Supply
Windows XP SP2
Latest VIA Hyperion Drivers

Hey guys it's me again.. Well the computer now seems to freeze less than it did before, but it still freezes.
After all this going back and forth and troubleshooting hassle ive decided it has to unfortunatlely be a hardware problem. I've stated before that it only freezed when running a 3d app and network card running.. but now it freezes even when I'm just on the web. It's just so totally random, sometimes it will freeze twice in one minute and sometimes it won't freeze for almost a whole day.
I've narrowed it down to 3 things: Bad HD, Bad Processor, and worst of all Bad Motherboard. Another possibility, does a the lithium battery on the motherboard ever cause problems if it's almost dead?(Assuming it's the CMOS battery?) And could that cause problems?
I had an episode before that I didn't tell you guys before. This was still after i had the network card, but probably unrelated. The computer once or twice made a very strange electrical zapping noise or screetching noise before and the whole system would almost fail and then try to resume again, and then just shut down.
After this event happened I figured it was the PSU not putting out enough power as I had installed new hardware lately. I bought a new 430W psu and while I haven't had the strange problem I had before, I still get random lockups.
I'm pretty sure it is the harddive, because it would make sense since I heard this noise before and the fact that it just freezes could just be the HD getting stuck and not spinning anymore.
It's funny because I had just replaced a faulty harddrive before in one of my older computers. However that one was much more obvious as it would constantly have to repair files in sectors. The HD I have now never comes up with errors, but maybe It is running fine before it decides to lockup.
Yet another thing it could be is the processor maybe just not generating enough juice to keep the processes going or something.
I did have problems with freezing before the network adapter now that I think back, but they were far and few between and now the problems are more pronounced. I'm going to hope it just the HD, if not it's really going to suck to already have to buy another motherboard or processor. I just built the system from scratch last year.
Sigh, Oh well. Glad for anymore insight on this issue and your opinions on what is most likely the problem. I'm going to go looking for a HD in the mean time.

Problem with printing over the shared network printer

I have a very irritating problem.
To describe the situation. I have 2 computers and non of them is mine. First one have Windows Vista, and second one have Windows 8.1. There is also a printer which is connected with usb to the computer with Windows 8.1. I managed to share that printer on
the network, and when I connect to that printer and enter username and password (from Windows 8.1) on the pc that have Windows Vista, I can print without any problem.
The problem start when I restart the computer with Windows Vista. I can't print unless I connect to that printer again and again enter the username and password. Like Windows Vista for some reason is not storing those credentials. It is very irritating to
do that all the time, becase everything worked before like a charm.
Is there something I didn't do about those credentials, or is there some batch script that I could run in startup that will connect Windows Vista PC with that printer without any user input?
Thank you.
Development Technician, Microsoft Certified Professional

Hi,
When you restart the Vista, have you checked the credential in credential manager (Control Panel\Credential Manager)? Does it exist? You can clear cached unused credential and manually add the printer Windows Credential in the manager and check if it
helps.
You can also use a logon script to add the printer automatically every time you logon to the PC, you can refer to thsi example, some content need to be changed depends on your configuration.
http://gallery.technet.microsoft.com/scriptcenter/10ab836d-4d38-45a5-8d27-ba9af1717930
http://blogs.technet.com/b/heyscriptingguy/archive/2006/12/12/how-can-i-add-a-network-printer-at-logon-and-optionally-make-that-the-default-printer.aspx
http://technet.microsoft.com/en-us/library/cc770908.aspx
Yolanda Zhu
TechNet Community Support

HT4993 i been having sim card problems with my iphone 5. am i the only one?

i been having sim card problems with my iphone 5. am i the only one?

Hello,
I'm also had problems with Iphone 5 , it read no sim card, i solved problem by removing sim card and cleaning with alcohol and q-tip and installing back.
Shut down phone.
On the side of phone , you will see a small pin hole, insert paper clip and sim card will come out, be careful to do it over a clean towel as not to let drop on floor, make sure your hands clean while doing this.
Insert sims card back and turn on, it should work again.
Good Luck.

Hi i am having a problem with itunes on this computer so i had to remove it and tryed to download it again and now every time the computer comes on i get a notification which says "the program cant start because MSVCR80.dll is missing from your computer

hi i am having a problem with itunes on this computer every time the computer comes on i get a notification which says"the program cant start because MSVCR80.dll is missing from your computer,try reinstalling the program to fix this problem" but when i click on ok it just keeps popping up 4-5 time and then gone.and i cant dopwnload the itunes again.help

You need to work through the user tip: https://discussions.apple.com/docs/DOC-6562

How do I get connected to a server on my network via an IP address? When I try to open in a URL and login as a registered user with proper login it errors out saying there was a problem with connecting to the server?

I am new to Mac...How do I get connected to a server on my network via a hyper link IP address path? When I try to open in a URL and login as a registered user with proper login it errors out saying there was a problem with connecting to the server?

Some of the following is going to use some technical terms — this area is inherently somewhat technical.
If you don't understand some part of the following reply, please ask.
Is this your own OS X Server system on your own network, or is this some other server within some larger organization?
You're posting this in the OS X Server forum, which is a software package that allows OS X systems to provide web-based and many other services; to become servers.
If it's your OS X Server on your network, then the network and DNS configurations are suspect, or the server is somehow malfunctioning or misconfigured. This is unfortunately fairly common, as some folks do try to avoid setting up DNS services.
If it's a larger organization and somebody else is managing the server and the network, then you'll probably need to contact the IT folks for assistance; to learn the network setup and DNS requirements, and if there's a problem with the server itself.
The basic web URL "hyper link IP address path" — without using DNS — usually looks something the following, where you'll need to replace 10.20.30.40 with the IP address of your server:
http://10.20.30.40
UptimeJeff has posted a URL that specifies the AFP file system; an OS X file share. That's used if you're connecting to an Apple storage service somewhere on your network. You might alternatively need to specify smb://10.20.30.40 or such, if it's a Windows file server. (There can be additional requirements for connecting to Windows Server systems, too.)
If there's local IT staff available here, please contact them for assistance. If these are your own local systems and your own local OS X Server system, then some information on the server will be needed. (If you're on a NAT'd network, you'll also need to get DNS services configured and working on your local OS X Server system and your network — you'll not be able to skip this step and reference ISP DNS servers here — or things can and usually will get weird.)

The "power search" yields no results whatsoever when i attempt to search. Is this a problem with itunes or my computer? Everything else seems to load just fine involving the itunes store.

I am attempting to search for artists on itunes and for some reason it keeps telling me there are no results when I know I am tying in the correct artist. I have been trying this repeatedly and using different artists and song names and I am still getting no results. Is this a problem with itunes?

The only thing I would be concerned about is.
1st, Where did the media come from.
2nd, Was it clean and free of scratches.
Most of the CD&DVD Drives in Powerbooks seem to be very very picky about the media they like to play with.
Always be carefull of the Source from where it came.
Commercially produced Media is rarely a problem.
It doesn't take much eiter to make them act silly.
Good Luck....Don

Is there a fix yet for the no sound problem with lion on the iMac without having to restart every time I switch the computer on?

Is there a fix yet for the no sound problem with lion on the iMac without having to restart every time I switch the computer on?

Try booting in Safe Mode by holding the the shift key immediately after powering on your system. Safe boot mode will for a directory check of your startup volume, then load only the required kernal extensions (kext files), and deletes some cache files. Once the system boots into Safe Mode you can simply restart the system to see whether the issue has been resolved.
If you still have the issue try resetting the SMC by shutting down the system and disconnecting the power cord for ~15 seconds, then reconnecting the power cord. Next, reset the parameter RAM (PRAM) by holding down the option-option-P-R keys after powering ON the system. Wait until the iMac restarts twice, then let the system boot normally.

Sorry but i dont speak a good english, i have a problem with my ipod the apps Twitter,Facebook not open but messenger(fb) music yes,I can do to make them work?

helpme please,sorry but i dont speak a good english, i have a problem with my ipod the apps Twitter,Facebook not open but messenger(fb) music yes,I can do to make them work?

See:
iOS: Troubleshooting applications purchased from the App Store
Restore from backup. See:
iOS: How to back up
Restore to factory settings/new iPod

Can't back-up new iMac with fusion HD. The back-up proceeds to within 10% of the total storage needed and then the "of" number increases. I suspect there is a problem with backing up the fusion drive. We have a new 3 TB time Capsule. Any ideas?

Can't back-up new iMac with fusion HD. The back-up proceeds to within 10% of the total storage needed and then the "of" number increases. I suspect there is a problem with backing up the fusion drive. We have a new 3 TB time Capsule. I tried excluding different parts of the software from the back-up but it didn't make any difference. I even tried exluding "invisible items" to no avail. Any ideas?

When you setup the wireless and ethernet in the computer.. ipv6 will be on automatic.. this is wrong for the latest TC firmware and airport utility. http://support.apple.com/kb/TS4597
Go to the wireless and ethernet setup in preferences and change ipv6 to link local.
Once you do the big backup by ethernet the wireless will function fine for incremental.. it is obviously not estimating the size correctly..
A full back-up on the iMac would be about 650 GB. The partial updates that I have been trying start out at 115MB and keep growing indefinitely. The original back-up never finished nor have any of the follow-up attempts.
The first estimate should be the full backup but it will keep growing as the backup advances.. I would also delete any inprogress files to make sure it is not messing up .. delete even a sparsebundle if there is one for the imac on the TC and start afresh once you have ethernet connection.
See A10 here.
Pondini may have some other clues there to give you an idea of why the backup is slow or not finishing.. there is a lot of issues with TM when it decides not to work.

My host name changes every few days, since Xmas adding a macbook its changed 6 times. Do I need to stop this? Does it cause problems with sharing between the iMac and macbook?

my host name changes every few days, since Xmas adding a macbook its changed 6 times. Do I need to stop this? Does it cause problems with sharing between the iMac and macbook?

There are several possible causes for this problem.
1. Two (or more) computers on the local network have the same Bonjour name, such as "X's-MacBook-Pro.local".
2. You have two simultaneous connections to the same local network: probably Ethernet and Wi-Fi. If applicable, disconnect the Ethernet cable or turn off Wi-Fi.
3. A Mac wakes from sleep due to network traffic. This is due to a bug in OS X that may only affect some models.
4. A device that gets its network address from the router wakes from sleep, and the address it was using before has been assigned to another device.
5. A third-party wireless router has incompatible settings or firmware. In that case, refer to the manufacturer or ISP for support. Restarting the router may help, temporarily.
6. See also this support article.
Rename the computer in the Sharing preference pane.

WRT54G Extremely slow navigating pages @ 192.168.1.1 - Could this be a network card problem?

Friend of mine is having Internet connection issues on his main PC which is hard wired to the router, He's using Comcast cable (18Mbit) and all of a sudden today the speed dropped to dialup speeds, literally, however its ONLY this main pc with the speed issue, there are 2 other computers connected wireless to the router and they are running full speed when testing on speedtest.net
While troubleshooting the problem I tried bypassing the router and the speed issue still remains, So I can pretty much rule out the router, But as part of my troubleshooting whenever I try to access the router's configuration pages via 192.168.1.1 it is VERY slow at responding.
For example when hitting enter after typing 192.168.1.1 it takes around 45 seconds to display the router configuration page, and at that point clicking on any other tabs takes 30 - 45 seconds as well to respond.
So my main question with this post is, is it possible his network card went bad? What would cause really slow access to the router configuration?
The PC is running Win 7 Ultimate 32bit and Ive tried running the network troubleshooter, uninstalled his network card in device manager / reinstalled the drivers but nothing seems to be working.
I also ran Malware Bytes and scan results were clean.
Any ideas appreciated!
Solved!
Go to Solution.

can you "borrow" a card? its the only way to be sure, eliminating hours of trial and error procedures. one of the mega electronics stores is a good source, if it solves your problem you keep the card, if not there is the return option
ps. i am not a tech, i just play one on tv!
pps. free speech is a human right! join Reporters Without Borders (http://en.rsf.org/) and help save the planet from censorship predators!

Problem with Pages on the iPad 2.

Hi all,
I have been having a strange problem with Pages on the iPad that I hope someone can find a solution for.
As a writer, I find that Pages on the iPad is a very good solution to my problem of needing something small and light to transport around, whilst still allowing me to do some serious writing. I use the Apple 3 battery bluetooth keyboard, and this gives me a superb working solution.
I started using the iPad 2 to do my second book and for the first 40,000 words everything was fine. But as I started going back and forth with the cursor keys, editing passages in the book, I noticed that the cursor position did not match up with the I beam cursor on screen. As it transitioned between pages it would loose it's corresponding position and the entry point for new text could be up to six characters in either direction.
Now this is not a problem if you enter a new page, as there is nothing beyond it, but in the majority of cases it is a major problem when going back over your work and editing it. I have to manually reset the start position of every new page so as to garantee the typing will go where I want it to.
Now I thought at first this was something to do with Bluetooth keyboard, but after using the onscreen keyboard and the find and replace function, I have noticed that it loses it's position in the document in a similar way. I have included a screen shot of it finding a problem I was searching for. In this case it is ", and" to be replaced with "and," or "and". Clearly in the image you can see that it is not happy and is not selecting the right things, if I replace it will replace exactly what is selected.
Has anyone else seen this problem. It seems to happen with large or small documents and I think that this is a fundamental problem with Pages on the iPad. Seeing as I can't get Apple to acknowledge this I brought it here for everyone else to check out. If we get enough voices on this, then we can make change happen.

That's right Br Abdullah, I'm finding the same problem with my itune Arabic library that I synced to iBooks version 1.5! As you say the pages are not arranged correctly.
The other problem that I'm finding is that the highlights & notes that i have made on the books on a previous version of ibooks, when synced with ibooks version 1.5, they are scattered everywhere, and sometimes in areas where there are no texts.
I left a message on the report a bug section of iBooks on the app store, and I contacted them on their feedback of apple product issues. I don't know what else we can do. It seems that no one is listening to us. I'm Dissapointed that I upgraded my iBooks version to 1.5; I was really looking forward to reading on my new iPhone 4S (on iBooks)!
What else can we do to get our concerns heared? Somebody? Anybody?

Does the apple tv make the computer act like a receiver from the tv?

does the apple tv make the computer act like a receiver from the tv?

When using home sharing, the computer is on and running iTunes and the content is sent over the local network to the Apple TV.

Network card problem with Mobo make the computer crazy!!!

Similar Messages

Maybe you are looking for