New Neo2plat problem occured: buzzing sound not due to on board sound tho
Right, it sounds like a small static zzzz zzz sound occuring, i have only recently heard this happeneing tho, and i have been conencted back to 10meg for 2 weeks, i didnt notice it before
i dont want it to be my PSU tho, its an antec trupower 550 so ample power is coming from it to the mobo, but theres no ruling it out either...
i do have my pc connected for massive amounts of time, days on end...
its only recently developed, but i have got the ethernet connected to the nvidia lan rather than the gigabyte
plus i have activated spread spectrum and the noise is slowly coming back even now
i have only really noticedf it since the alst time i took the side off my case aswell tho...
i might take everyhitng out the case and tie everything up just in case a cable etc is rubbing against a fan :S
:(
Have ya cleaned the dust from it lately?
And have you bothered to try to isolate where the sound is coming from?
You could do that with some 1/4 inch neoprene tubing and a small funnel.
Put the tube in your ear and point the funnel at various points, it works, really
Reminds me of my days as a kid working in a garage, and the customers would come in and attempt to mimic the noise thier car was making
RrRrRzZzZzZzZzRrRrRrR
Similar Messages
-
My New Laptop made a buzzing sound?
- Hi ! I hope many of you are having a wonderful mourning . My small question is that when I just bought this laptop (HP Envy 17) the day after, I began listening to music. I do not know why it made a buzzing sound and that is something that has been happening to my older Laptop and I do not want such circumstances to happen to this new laptop . Please if anyone is willing to tell me what ways I can do to prevent this buzzing sound from occuring so often like it did in my old laptop .
I apprieciate your time in helping me . I hope you have a wonderful day today .Hi ImKevin,
First of all, I'm sorry that you're having trouble with your laptop!
It would be really hard for me to pinpoint the exact cause of the buzzing sound so therefore, I suggest that you take
your laptop and visit a HP Service Center close to you. The engineers will be able to help you find the cause and provide
different solutions. You can contact HP using the link below and get the support that you need.
I'm sorry I wasn't able to provide you with a straight solution.
http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
Hope this helps!
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others. -
NEW BIOS UPDATE - Fixed buzzing sound from GPU?
It says it fixed the buzzing sound near speaker and battery when on battery power. Could this be the issue that people with the Intel Proccesor have when on battery power it makes a noise?
Hello,
I don´t exactly know, if the bios update disable C4 states, to prevent buzzing.
But if so, you´ll probably loose battery life, cause the cpu would´t get into lower power states.
May be the fan (link in german) will be running more often, to keep the Nvidia chip cooler, also.
I think if your TP suffers from whine, then give it a try or wait, till someone could tell us here
about his experience.
Message Edited by Agotthelf on 29-10-2008 09:59 PM
Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
Please insert your type, model (not S/N) number and used OS in your posts.
I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
English Community Deutsche Community Comunidad en Español -
IWork from old to new Mac, problem occurred.
Greetings,
iWork I have bought years ago on CD and installed on MB-Pro.
Now I have a MB-Air.
Since the Air has no CD/DVD player I transferred iWork from Pro to Air.
Starting up Pages (i.e.) on the Air I get this message:
I can't find the installer (also through a search. iWork search gives: iWork folder containing: Keynote, Numbers, Pages apps)
The DVD player of the Pro is broken.
I rather not repurchase or buy an update.
I rather not Download due expenses ($40.00 per GB) (Sitting in a cafe or neighbour i.e. to Download is not an option)
Is there a solution to get iWork working properly from this situation?
Thanks!I never wrote that applications can't be updated when they are stored in a non standard location.
I wrote that iWork applications, when delivered as a single package, must be stored together in a given folder for such process.
At this time they weren't delivered as single separated apps but as a package.
In fact this feature apply only to iWork '09.
It's because for this package, updaters applied to the three embedded applications.
Only the late update was a Keynote only one.
For iWork '08, there were separated updaters for each applications so, installing them out of their original folder wasn't a problem.
The fact that you forget to copy the resources when you wanr to work from an other system is not an Apple problem, it's yours.
I repeat that you were wrong and that you didn't understood what you were writing about, because the shared folder, the one which must be copied, is not the one which you described with :
upon first run, the app creates its folder in Application Support if need be.
The shared folder:
Macintosh HD:Library:Application Support:iWork '09:
or
Macintosh HD:Library:Application Support:iWork '09:
is not created at application's first launch, it's created by the installer during the installation process.
The one which you described is :
Macintosh HD:Users:<userAccount>:Library:Application Support:iWork:
For someone understanding the way iWork is installed, the copy process is perfectly neat and clear.
It is more efficient than installing then apply the required updates which, to be up to date require :
install iWork
apply iWork update9.1
apply keynote update 5.1.1
Yvan KOENIG (VALLAURIS, France) mercredi 11 avril 2012
iMac 21”5, i7, 2.8 GHz, 12 Gbytes, 1 Tbytes, mac OS X 10.6.8 and 10.7.3
My Box account is : http://www.box.com/s/00qnssoyeq2xvc22ra4k -
On my new iMac, mail has no sound after waking from sleep. If I select do not wake for network access in general preferences, the problem does not occur. Anyone have an idea on how to fix this? Thanks --
Same here on an older iMac since Lion. Thanks for the uncheck wake for network access tip though, it doesn't do it either in that case, I will leave it that way.
-
Some videos that are taken with my iphone's camera are not making sounds, this problem occured today to all videos i recorded starting from today, please help
It also takes time for the photos to be transferred out of your iPhone and into Photo stream on Apple's iCloud servers.
Note that this can't happen if your iPhone is not connected to a WiFi network:
When you enable My Photo Stream on your devices, all new photos you take or import to those devices will be automatically added to your photo stream.
iOS devices: New photos you take are automatically uploaded to your photo stream when you leave the Camera app and are connected to Wi-Fi. My Photo Stream does not push photos over cellular connections.
Macs: Any new photos you import to iPhoto or Aperture begin uploading automatically when you have a Wi-Fi or Ethernet connection. Or you can change your iPhoto or Aperture preferences so that only photos you manually add to My Photo Stream are uploaded.
PC with iCloud Control Panel 2.0 or later: Open a Windows Explorer window and under Favorites select iCloud Photos if you are using iCloud Control Panel 3.0 (or Photo Stream if you are using 2.0 to 2.1.2). Open My Photo Stream. Click the "Add photos" button. Select the photos to import to My Photo Stream, then click Open.
from here: http://support.apple.com/kb/ht4106 -
I'm using iphone 5s with ios 7.1.2 & I am facing a new problem after every missed call. i phone gets freezed on its lock screen. It seems that its main screen touch is not working properly. It should be bug introduced by apple . This problem occurs after each and every missed call .There is no patch announcement for this issue yet. There are few workaround to fix this issue: Reboot your iphone. But its irritating to reboot the phone frequently after each issue....
Hello dipthebe,
Check out the articles below go through troubleshooting steps for your iPhone when the screen is unresponsive. You may want to try and restore your iPhone as a new device and then test out what happens when you miss a call to see if the issue is still present afterwards.
iPhone, iPad, iPod touch: Troubleshooting touchscreen response
http://support.apple.com/kb/ts1827
Use iTunes to restore your iOS device to factory settings
http://support.apple.com/kb/HT1414
Regards,
-Norm G. -
This problem happened intermittently in the past but now happens every time I plug in the phone. I suspect it might be a problem with my computer, an Acer Aspire 4530, perhaps with it's charging function via usb ports? The phone makes the same buzzing sound twice when I connect to other power sources, but continues when connected to computer. I have this issue even when the phone is 100% charged.
This problem happened intermittently in the past but now happens every time I plug in the phone. I suspect it might be a problem with my computer, an Acer Aspire 4530, perhaps with it's charging function via usb ports? The phone makes the same buzzing sound twice when I connect to other power sources, but continues when connected to computer. I have this issue even when the phone is 100% charged.
-
iPhone will not ring if locked when when Do Not Disturb is not on and the phone is not on silent (button on side is not red). This problem occurs regardless of whether it I have Do not Disturb on (manually, or scheduled) or COMPLETELY OFF. I've tried wiping the phone and reinstalling from a saved copy but of course the problem comes back because the problem is inherent in the save. There are two options under "Silence" at the bottom of the Do Not Disturb preferences. "Always" or "Only when iPhone is locked". Those are the only two options and I want neither. No amount of deselecting will work. It forces you to pick one.
Does anyone have a solution given that I've better explained the problem?The settings at the bottom of the Do Not Disturb page do not matter if you have the switch for Manual turned to off, or the Scheduled turned to off.
When the phone is unlocked, if you try to raise the volume of the ringer, what do you see on the screen? Does it say ringer, do you see the word headphones anywhere? -
System freezes due to hard disk problems only on Linux (not windows)
Intro/context:
Recently i've bought (about 2 months) a new laptop, a Lenovo G50-70, which came with Windows 8.1. As i had no interest on that OS, i formatted the disk and installed only Arch Linux. During that time i experienced system freezes which i had no idea why they were happening. As time went by, i found disk errors on system logs related to hard drive. I searched those errors and almost everything i found was that my hard drive had problems, so i decided to use my warranty. But first, i installed the original OS back again. And after using it a couple of weeks, i didn't experiencie any problem with my hard drive (on Linux it was really frequent). Now i've installed Arch Linux back, along with original Windows 8.1, having dual boot. There is no disk problem when using Windows, but when on Arch, i have the same errors and problems i used to have. So i assume it may be related to kernel or some confniguration issue.
I also haven't noticed any relation between system freezes and system use. I mean, it can happen either under light or heavy use.
tl dr: system freezes randomly for some minutes when using linux due to hard drive problems. The problem doesn't happen on windows.
What i've done so far:
The first period i was on Arch, i run smart (long and short), fsck, and hdparm tests. And nothing (no errors). Searched for bad blocks, and nothing. When back on windows, i also run tests on hdd and found no problems, except some sector reallocation not-that-nice indicators. These problems occured at the end of the first arch installation period. But still i currently experience no problem on windows.
I've also tried setting libata: noncq, 3.0G, noacpi, noapic kernel parameters, and had no result.
Changed BIOS setting from AHCI to Legacy, and no result. Also updated BIOS and no result.
I found no firmware update for this hard drive.
So i don't know what other thing i can try. I want to emphasize that there is no problem, no freezing, when running Windows, so i don't think it's a hard drive issue.
Info:
Hard drive is a Toshiba 2.5" HDD MQ01ABD100 5400 rpm.
Some logs i've recollected all this time:
journalctl -xfa --system
abr 21 13:51:13 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 21 13:51:24 echoes kernel: ata1.00: failed command: CHECK POWER MODE
abr 21 13:51:24 echoes kernel: ata1.00: cmd e5/00:00:00:00:00/00:00:00:00:00/00 tag 7
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 21 13:51:24 echoes kernel: ata1.00: status: { DRDY }
abr 21 13:51:24 echoes kernel: ata1: hard resetting link
abr 21 13:51:24 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 21 13:51:24 echoes kernel: ata1.00: configured for UDMA/100
abr 21 13:51:24 echoes kernel: ata1: EH complete
abr 21 14:01:40 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 21 14:02:01 echoes kernel: ata1.00: failed command: SMART
abr 21 14:02:01 echoes kernel: ata1.00: cmd b0/d1:01:00:4f:c2/00:00:00:00:00/00 tag 23 pio 512 in
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 21 14:02:01 echoes kernel: ata1.00: status: { DRDY }
abr 21 14:02:01 echoes kernel: ata1: hard resetting link
abr 21 14:02:01 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 21 14:02:01 echoes kernel: ata1.00: configured for UDMA/100
abr 21 14:02:01 echoes kernel: ata1: EH complete
abr 21 14:02:01 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 21 14:02:01 echoes kernel: ata1.00: failed command: SMART
abr 21 14:02:01 echoes kernel: ata1.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 22 pio 512 in
res 40/00:ff:ff:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 21 14:02:01 echoes kernel: ata1.00: status: { DRDY }
abr 21 14:02:01 echoes kernel: ata1: hard resetting link
abr 21 14:02:01 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 21 14:02:01 echoes kernel: ata1.00: configured for UDMA/100
abr 21 14:02:01 echoes kernel: ata1: EH complete
abr 21 14:02:01 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 21 14:02:01 echoes kernel: ata1.00: failed command: SMART
abr 21 14:02:01 echoes kernel: ata1.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 18
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 21 14:02:01 echoes kernel: ata1.00: status: { DRDY }
abr 21 14:02:01 echoes kernel: ata1: hard resetting link
abr 21 14:02:01 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 21 14:02:01 echoes kernel: ata1.00: configured for UDMA/100
abr 21 14:02:01 echoes kernel: ata1: EH complete
abr 21 14:01:51 echoes udisksd[627]: Error performing housekeeping for drive /org/freedesktop/UDisks2/drives/TOSHIBA_MQ01ABD100_Y44MT611T: Error updating SMART data: sk_disk_smart_status: Input/output error (udisks-error-quark, 0)
dmesg
[55661.023028] ata1.00: exception Emask 0x0 SAct 0x8000 SErr 0x0 action 0x6 frozen
[55661.023034] ata1.00: failed command: READ FPDMA QUEUED
[55661.023040] ata1.00: cmd 60/08:78:18:08:c0/00:00:4b:00:00/40 tag 15 ncq 4096 in
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[55661.023042] ata1.00: status: { DRDY }
[55661.023046] ata1: hard resetting link
[55666.358537] ata1: link is slow to respond, please be patient (ready=0)
[55671.053813] ata1: COMRESET failed (errno=-16)
[55671.053819] ata1: hard resetting link
[55676.389438] ata1: link is slow to respond, please be patient (ready=0)
[55678.897149] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[55681.320305] ata1.00: configured for UDMA/100
[55681.320319] ata1.00: device reported invalid CHS sector 0
[55681.320349] ata1: EH complete
[55729.969443] [drm:intel_set_cpu_fifo_underrun_reporting [i915]] *ERROR* uncleared fifo underrun on pipe A
[55729.969588] [drm:intel_cpu_fifo_underrun_irq_handler [i915]] *ERROR* CPU pipe A FIFO underrun
dmesg
[102884.889930] systemd[1]: systemd-journald.service: main process exited, code=dumped, status=6/ABRT
[102884.890305] systemd[1]: Unit systemd-journald.service entered failed state.
[102884.890333] systemd[1]: systemd-journald.service failed.
[102885.560745] systemd-coredump[28916]: Detected coredump of the journal daemon itself, diverted to /var/lib/systemd/coredump/core.systemd-journal.0.5bf9a012fed048ce8975998cf3c3c20e.6705.1427990901000000.
[102885.860957] systemd-journald[28919]: File /var/log/journal/b130c96d1371445d9ddeb40c51c77dd6/system.journal corrupted or uncleanly shut down, renaming and replacing.
[102921.797810] systemd-journald[28919]: File /var/log/journal/b130c96d1371445d9ddeb40c51c77dd6/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
[104179.117363] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[104179.117369] ata1.00: failed command: READ FPDMA QUEUED
[104179.117375] ata1.00: cmd 60/08:00:48:88:8b/00:00:4d:00:00/40 tag 0 ncq 4096 in
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[104179.117377] ata1.00: status: { DRDY }
[104179.117381] ata1: hard resetting link
[104184.453382] ata1: link is slow to respond, please be patient (ready=0)
[104189.149114] ata1: COMRESET failed (errno=-16)
[104189.149121] ata1: hard resetting link
[104189.469276] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[104189.952982] ata1.00: configured for UDMA/100
[104189.952989] ata1.00: device reported invalid CHS sector 0
[104189.953004] ata1: EH complete
[104508.223792] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[104508.223798] ata1.00: failed command: SMART
[104508.223803] ata1.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 2
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[104508.223806] ata1.00: status: { DRDY }
[104508.223810] ata1: hard resetting link
[104509.984601] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[104510.698126] ata1.00: configured for UDMA/100
[104510.698157] ata1: EH complete
One of the latest and worse
journalctl -xfa --system
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:00:e0:d6:75/00:00:00:00:00/40 tag 0 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:08:08:d8:75/00:00:00:00:00/40 tag 1 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:10:30:d9:75/00:00:00:00:00/40 tag 2 ncq 4096 out
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:18:58:da:75/00:00:00:00:00/40 tag 3 ncq 4096 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:20:e8:e5:75/00:00:00:00:00/40 tag 4 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:28:80:db:75/00:00:00:00:00/40 tag 5 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:30:68:dd:75/00:00:00:00:00/40 tag 6 ncq 4096 out
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:38:90:de:75/00:00:00:00:00/40 tag 7 ncq 4096 out
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:40:b8:df:75/00:00:00:00:00/40 tag 8 ncq 4096 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:48:90:e1:75/00:00:00:00:00/40 tag 9 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:50:98:e3:75/00:00:00:00:00/40 tag 10 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:58:c0:e4:75/00:00:00:00:00/40 tag 11 ncq 4096 out
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/c8:78:28:b9:2a/0b:00:4e:00:00/40 tag 15 ncq 1544192 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:80:b0:4b:c0/00:00:4f:00:00/40 tag 16 ncq 4096 out
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/10:88:90:4b:80/00:00:50:00:00/40 tag 17 ncq 8192 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:90:98:22:81/00:00:50:00:00/40 tag 18 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:98:00:0e:00/00:00:5f:00:00/40 tag 19 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:a0:00:08:80/00:00:5f:00:00/40 tag 20 ncq 4096 out
res 40/00:ff:ff:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:a8:80:08:80/00:00:5f:00:00/40 tag 21 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/10:b0:08:0b:81/00:00:5f:00:00/40 tag 22 ncq 8192 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:b8:70:c8:75/00:00:00:00:00/40 tag 23 ncq 4096 out
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:c0:20:c9:75/00:00:00:00:00/40 tag 24 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:c8:88:c9:75/00:00:00:00:00/40 tag 25 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:d0:58:ca:75/00:00:00:00:00/40 tag 26 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:d8:a0:ce:75/00:00:00:00:00/40 tag 27 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:e0:68:d3:75/00:00:00:00:00/40 tag 28 ncq 4096 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:e8:90:d4:75/00:00:00:00:00/40 tag 29 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:f0:b8:d5:75/00:00:00:00:00/40 tag 30 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1: hard resetting link
abr 22 12:57:11 echoes kernel: ata1: link is slow to respond, please be patient (ready=0)
abr 22 12:57:11 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 22 12:57:11 echoes kernel: ata1.00: configured for UDMA/100
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x06
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] CDB:
abr 22 12:57:11 echoes kernel: cdb[0]=0x2a: 2a 00 12 88 d7 c0 00 04 d0 00
abr 22 12:57:11 echoes kernel: blk_update_request: I/O error, dev sda, sector 310958016
abr 22 12:57:11 echoes kernel: EXT4-fs warning (device sda2): ext4_end_bio:317: I/O error -5 writing to inode 36311758 (offset 8388608 size 2695168 starting block 38869906)
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995128
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995129
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995130
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995131
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995132
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995133
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995134
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995135
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995136
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995137
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x06
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] CDB:
abr 22 12:57:11 echoes kernel: cdb[0]=0x2a: 2a 00 4b dd 39 88 00 01 78 00
abr 22 12:57:11 echoes kernel: blk_update_request: I/O error, dev sda, sector 1272789384
abr 22 12:57:11 echoes kernel: EXT4-fs warning (device sda2): ext4_end_bio:317: I/O error -5 writing to inode 34999445 (offset 0 size 192512 starting block 159098720)
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x06
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] CDB:
abr 22 12:57:11 echoes kernel: cdb[0]=0x2a: 2a 00 4e 2a b3 e8 00 05 40 00
abr 22 12:57:11 echoes kernel: blk_update_request: I/O error, dev sda, sector 1311421416
abr 22 12:57:11 echoes kernel: EXT4-fs warning (device sda2): ext4_end_bio:317: I/O error -5 writing to inode 35001016 (offset 0 size 2232320 starting block 163927845)
abr 22 12:57:11 echoes kernel: ata1: EH complete
abr 22 12:57:11 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 22 12:57:11 echoes kernel: ata1.00: failed command: CHECK POWER MODE
abr 22 12:57:11 echoes kernel: ata1.00: cmd e5/00:00:00:00:00/00:00:00:00:00/00 tag 25
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1: hard resetting link
abr 22 12:57:11 echoes kernel: ata1: link is slow to respond, please be patient (ready=0)
abr 22 12:57:11 echoes kernel: ata1: COMRESET failed (errno=-16)
abr 22 12:57:11 echoes kernel: ata1: hard resetting link
abr 22 12:57:11 echoes kernel: ata1: link is slow to respond, please be patient (ready=0)
abr 22 12:57:11 echoes kernel: ata1: COMRESET failed (errno=-16)
abr 22 12:57:11 echoes kernel: ata1: hard resetting link
abr 22 12:57:11 echoes kernel: ata1: link is slow to respond, please be patient (ready=0)
abr 22 12:57:11 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 22 12:57:11 echoes kernel: ata1.00: configured for UDMA/100
abr 22 12:57:11 echoes kernel: ata1: EH complete
Current smart status:
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-4.0.1-1-ARCH] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: Y44MT611T
LU WWN Device Id: 5 000039 5e1a80e85
Firmware Version: AX1P5E
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun May 3 16:42:06 2015 ART
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 234) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1671
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 306
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 152
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 699
10 Spin_Retry_Count 0x0033 106 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 300
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 216
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 14
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 14140
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 34 (Min/Max 16/44)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 19
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 099 099 000 Old_age Always - 515
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 190
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Vendor (0x50) Completed without error 00% 611 -
# 2 Short offline Completed without error 00% 611 -
# 3 Short offline Completed without error 00% 597 -
# 4 Vendor (0x50) Completed without error 00% 583 -
# 5 Short offline Completed without error 00% 583 -
# 6 Vendor (0x50) Completed without error 00% 575 -
# 7 Short offline Completed without error 00% 575 -
# 8 Short offline Completed without error 00% 547 -
# 9 Extended offline Completed without error 00% 529 -
#10 Short offline Completed without error 00% 355 -
#11 Short offline Completed without error 00% 355 -
#12 Extended offline Aborted by host 70% 355 -
#13 Short offline Completed without error 00% 319 -
#14 Vendor (0x50) Completed without error 00% 13 -
#15 Short offline Completed without error 00% 13 -
#16 Short offline Completed without error 00% 12 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Kernels used have been from 3.9 to current: Linux echoes 4.0.1-1-ARCH #1 SMP PREEMPT Wed Apr 29 12:00:26 CEST 2015 x86_64 GNU/Linux
Last edited by jesu (2015-05-03 19:42:53)Something i'd noticed both the first time i was on arch and now i've reinstalled it, was that at first i didn't have this problem. I mean, when Arch was just installed. While i was installing and setting up everything.
Now, i'm not 100% sure about this, but i think problems began when using my current user. Disk is partitioned the following way:
$ lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 931,5G 0 disk
├─sda1 8:1 0 1000M 0 part
├─sda2 8:2 0 260M 0 part /boot
├─sda3 8:3 0 207,7G 0 part
├─sda4 8:4 0 25G 0 part
├─sda5 8:5 0 14,8G 0 part
├─sda6 8:6 0 80,5G 0 part /
├─sda8 8:8 0 599G 0 part /home
└─sda9 8:9 0 2G 0 part [SWAP]
So, i believe problems, for some reason, are related (and were related), both before and now, to the /home partition, /dev/sda8 in this ocassion.
Because of this, i booted into systemd rescue mode, like root, rw, and unmounted /home partition. Despite root-only limitations, i used the system for a couple of hours, started lxqt, browsed the web mainly, and experienced no problem at all.
Now i booted normally, with my regular user, and these problems are experienced just like before (and almost instantly, like 3 or 5 minutes after starting system use).
dmesg this time showed a some different log, though it's not the first time i see this. I just didn't saved that kind of log before.
[ 653.821719] ata1.00: exception Emask 0x0 SAct 0x100 SErr 0x0 action 0x6 frozen
[ 653.821726] ata1.00: failed command: READ FPDMA QUEUED
[ 653.821732] ata1.00: cmd 60/08:40:60:25:43/00:00:1b:00:00/40 tag 8 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 653.821735] ata1.00: status: { DRDY }
[ 653.821739] ata1: hard resetting link
[ 659.156760] ata1: link is slow to respond, please be patient (ready=0)
[ 663.851604] ata1: COMRESET failed (errno=-16)
[ 663.851610] ata1: hard resetting link
[ 669.186591] ata1: link is slow to respond, please be patient (ready=0)
[ 673.881456] ata1: COMRESET failed (errno=-16)
[ 673.881462] ata1: hard resetting link
[ 679.216481] ata1: link is slow to respond, please be patient (ready=0)
[ 702.743982] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 703.012578] ata1.00: configured for UDMA/100
[ 703.012584] ata1.00: device reported invalid CHS sector 0
[ 703.012599] ata1: EH complete
[ 714.097642] systemd[1]: systemd-journald.service watchdog timeout (limit 1min)!
[ 742.443488] sd 0:0:0:0: [sda] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x06
[ 742.443494] sd 0:0:0:0: [sda] tag#18 CDB: opcode=0x2a 2a 00 28 c3 c6 40 00 00 10 00
[ 742.443497] blk_update_request: I/O error, dev sda, sector 683918912
[ 742.443503] EXT4-fs warning (device sda8): ext4_end_bio:317: I/O error -5 writing to inode 20322020 (offset 0 size 0 starting block 85489866)
[ 742.443506] Buffer I/O error on device sda8, logical block 9323208
[ 742.443508] Buffer I/O error on device sda8, logical block 9323209
[ 742.443515] sd 0:0:0:0: [sda] tag#19 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x06
[ 742.443518] sd 0:0:0:0: [sda] tag#19 CDB: opcode=0x2a 2a 00 28 c3 c6 80 00 00 10 00
[ 742.443520] blk_update_request: I/O error, dev sda, sector 683918976
[ 742.443522] EXT4-fs warning (device sda8): ext4_end_bio:317: I/O error -5 writing to inode 20322020 (offset 0 size 0 starting block 85489874)
[ 742.443524] Buffer I/O error on device sda8, logical block 9323216
[ 742.443526] Buffer I/O error on device sda8, logical block 9323217
[ 742.443531] sd 0:0:0:0: [sda] tag#20 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x06
[ 742.443534] sd 0:0:0:0: [sda] tag#20 CDB: opcode=0x2a 2a 00 28 c3 c6 d0 00 00 10 00
[ 742.443536] blk_update_request: I/O error, dev sda, sector 683919056
[ 742.443538] EXT4-fs warning (device sda8): ext4_end_bio:317: I/O error -5 writing to inode 20322020 (offset 0 size 0 starting block 85489884)
[ 742.443540] Buffer I/O error on device sda8, logical block 9323226
[ 742.443542] Buffer I/O error on device sda8, logical block 9323227
[ 742.443547] sd 0:0:0:0: [sda] tag#21 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x06
[ 742.443549] sd 0:0:0:0: [sda] tag#21 CDB: opcode=0x2a 2a 00 28 c3 c7 10 00 00 10 00
[ 742.443551] blk_update_request: I/O error, dev sda, sector 683919120
[ 742.443553] EXT4-fs warning (device sda8): ext4_end_bio:317: I/O error -5 writing to inode 20322020 (offset 0 size 0 starting block 85489892)
[ 742.443555] Buffer I/O error on device sda8, logical block 9323234
[ 742.443557] Buffer I/O error on device sda8, logical block 9323235
[ 756.187685] systemd[1]: systemd-journald.service: main process exited, code=dumped, status=6/ABRT
[ 756.187986] systemd[1]: Unit systemd-journald.service entered failed state.
[ 756.188116] systemd[1]: systemd-journald.service failed.
[ 756.188474] systemd[1]: systemd-journald.service has no holdoff time, scheduling restart.
[ 756.189106] systemd[1]: Stopping Flush Journal to Persistent Storage...
[ 756.189143] systemd[1]: Listening on Journal Audit Socket.
[ 756.189801] systemd[1]: Starting Journal Service...
[ 757.525493] systemd-coredump[1038]: Detected coredump of the journal daemon itself, diverted to /var/lib/systemd/coredump/core.systemd-journal.0.b8610e85f9074a418534aaee0adbac56.141.1430763073000000.lz4.
[ 758.133944] systemd-journald[1050]: File /var/log/journal/f646626ba4b647f48501020bf12ca33b/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 758.503041] systemd[1]: Started Journal Service.
[ 759.180771] systemd-journald[1050]: File /var/log/journal/f646626ba4b647f48501020bf12ca33b/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
[ 974.867721] ata1.00: exception Emask 0x0 SAct 0x3f80 SErr 0x0 action 0x6 frozen
[ 974.867732] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867742] ata1.00: cmd 61/08:38:68:d3:c5/00:00:1a:00:00/40 tag 7 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867747] ata1.00: status: { DRDY }
[ 974.867751] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867759] ata1.00: cmd 61/08:40:88:d3:c5/00:00:1a:00:00/40 tag 8 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867763] ata1.00: status: { DRDY }
[ 974.867767] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867774] ata1.00: cmd 61/08:48:a0:d3:c5/00:00:1a:00:00/40 tag 9 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867778] ata1.00: status: { DRDY }
[ 974.867781] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867789] ata1.00: cmd 61/20:50:c0:d3:c5/00:00:1a:00:00/40 tag 10 ncq 16384 out
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867793] ata1.00: status: { DRDY }
[ 974.867796] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867803] ata1.00: cmd 61/10:58:f0:d3:c5/00:00:1a:00:00/40 tag 11 ncq 8192 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867807] ata1.00: status: { DRDY }
[ 974.867810] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867817] ata1.00: cmd 61/08:60:10:d4:c5/00:00:1a:00:00/40 tag 12 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867821] ata1.00: status: { DRDY }
[ 974.867824] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867831] ata1.00: cmd 61/18:68:28:d4:c5/00:00:1a:00:00/40 tag 13 ncq 12288 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867835] ata1.00: status: { DRDY }
[ 974.867841] ata1: hard resetting link
[ 980.202774] ata1: link is slow to respond, please be patient (ready=0)
[ 984.900902] ata1: COMRESET failed (errno=-16)
[ 984.900908] ata1: hard resetting link
[ 990.236024] ata1: link is slow to respond, please be patient (ready=0)
[ 994.930829] ata1: COMRESET failed (errno=-16)
[ 994.930836] ata1: hard resetting link
[ 996.798104] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 997.014012] ata1.00: configured for UDMA/100
[ 997.014020] ata1.00: device reported invalid CHS sector 0
[ 997.014023] ata1.00: device reported invalid CHS sector 0
[ 997.014025] ata1.00: device reported invalid CHS sector 0
[ 997.014026] ata1.00: device reported invalid CHS sector 0
[ 997.014028] ata1.00: device reported invalid CHS sector 0
[ 997.014030] ata1.00: device reported invalid CHS sector 0
[ 997.014031] ata1.00: device reported invalid CHS sector 0
[ 997.014065] ata1: EH complete
There are some sda8 (home) related messages. I also found these messages first time Arch was installed (i think also related to home partition).
root and home partitions are both ext4. -
Buzzing sound when I play a note...
With Garageband (1) I suddenly, and for no apparent reason developed a problem. Whenever I played a note it would buzz. I don't have the same problem with Pro-tools and I'm using the same keyboard and everything. So I bought Ilife 5' thinking that would solve the problem. Not so. Same buzz sound on every instrument and every key etc. I've tried dumping the instruments and reloading, restarting, etc. etc. Anybody have any ideas?
Hey Wheat,
Sorry to be vague. Okay, I have an Imac G4, and an MAudio keystation 49 plugged into the mac via USB. A very simple set-up. It worked great for a long time on Garageband 1. I made some really cool songs then all of a sudden this buzzing sound. You can barely hear the instruments (Garageband's instruments) under the buzz. In addition to this, I also work with Pro-Tools and an M-Box. I can play Sample-Tank instruments (a plug-in) with the Keystation in Pro-Tools with no problem, but I still love working with GarageBand. As I said I bought the new Ilife suite but have had no improvement with the sound in GarageBand. I run my sounds out to the M-Box via USB, then to a small Mackie mixer and onto the monitors. The fact that I can play Sample-Tank instruments with no problem in Pro-Tools tells me that the problem I'm having with Garageband's instruments are somewhere in Garageband. Does that make any sense? Thanks for responding! -
when i play a song from my itunes library, there is a short "buzzing" sound about every 20-30 seconds. This same thing happened some time ago, and i thought i had it sovled by verifying that itunes was my default player. Howerver, it has started up again. Any ideas how to fix the problem??
I am having the same problem I have over 11.5 GB of .tmp files, many 1000s. Here is a thread I have found with some more info:
http://discussions.apple.com/thread.jspa?messageID=824308
That thread is almost a year old so I'm not holding out hope for a fix from apple. I'm going to try deleting them and see how it goes... -
I have a new iPhone 5C, have the sounds alerts set up. But I'm not getting sound alerts for new voicemail, only the red circle on the screen. How can I make the sound alert work?
I have had this same problem for weeks now with my 4S. I just got a new 5S after being extremely frustrated and the same thing - no sounds. After searching posts all over, I couldn't find a solution. I just told my friend of the issue and he asked "Do you have the Do Not Distrub on?" I didn't even know such a function existed. Upon looking that was exactly the issue.
To resolve, go to Settings> Do Not Disturb> Manual. If it is green, turn it off. You will now get phone calls and text alerts.
This functionality is also on your quick access utility menu (slide up menu). I assume this is how it was enabled on my phone.
I will post on other sites since I searched for weeks for this solution and didn't see it anywhere. Good luck! -
Can't create a new illustration. Problems occurred while saving the print file.
I can't open a new Illustrator file. It sends me this error: Can't create a new illustration. Problems occurred while saving the print file. ID:-1
I opened a previous document created in CC, but it will not allow me to copy and paste items from one doc to another.
I have rebooted with no avail.
System:
Adobe Creative Cloud CC
Mac Book Pro 2012
2.6 GHz Intel Core i7
8 GB 1600 MHz DDR3Is a printer connected? Is it turned ON? Is the driver up to date?
Illustrator checks this every time and also writes information on the printer into the file. -
When i play a video or movie i get a buzzing sound from the speakers. how do i solve this problem?
I get this buzzing sound from my speakers when I play a video, or movie either from the internet or playing a DVD. What can I do to solve this problem
A: There is no such thing as an unlocked iPhone 3Gs in the United States. ALL iPhone 3Gs's sold in the US are locked to AT&T. AT&T will NOT unlock iPhones, therefore it is not legitimately unlocked.
B: Sprint is a CDMA network as others have mentioned. They do NOT use SIM cards. The iPhone 3Gs will NEVER work on Sprint. Ever. It's not physically possible.
Either your Uncle misunderstood or he was mislead. Send it back and tell him to get his money back. Buy an iPhone in India from a supported carrier.
Maybe you are looking for
-
I'm constantly downloading files that should go into a specific folder but I don't have a 'Save As' option when I choose to save. As a result everything goes into the Download folder. This means I have to go to the download folder and move it. How ca
-
Adobe Encore - Completely Useless for Bluray
Hello, I'd just like to post my experiences for creating a blu-ray disc with Adobe Encore... actually I've been unable to create a proper bluray with this useless program. Here's what happens: Adobe Encore CS3: Error --- "Out of Memory" -- The blur
-
CRM 2007 Mediallist + Upgrade Master Guide Required
Hello All, Could any one help me in find out CRM 2007 Mediallist and Upgrade Master Guide. If found pls send me the URL . Thanks, Prabhakar BR
-
For example, I type in South Caronlina Contractors license in google. I see the SCCL website. It is the official website. I click on it and instead of getting the state site, I get redirected to an advertisement. 10 minutes later I go through the sam
-
Installing Elements 10 on my new computer.
I bought Elements 10 i January 2012, and want to install it on my new computer. Adobe chat can't help me because this is a VERY old version. I can't find my serialnumber, and it is not on my page in Adobes system eighter.