Newbie: Airport Express, DSL internet, G4 iBook, and me
Hello everyone!
I have just purchased an Airport Express (with AirTunes), to connect to the internet wirelessly. I have the latest generation g4 iBook (before they switched to the new MacBook models), and so it came installed with an Airport card, software, etc.
I connect to the internet with a DSL modem, and normally I would connect to the modem with an ethernet cable.
I am having trouble setting up the Airport Express so it can connect to my ISP, and I'm not finding the right place to enter my ISP login information (username and password).
Can anyone help with this? I've tried the Airport Setup assistant, but it didn't work!
Many thanks to everyone!
rdisanto, Welcome to the discussion area!
Does your ISP use PPPoE for the connection? If so, configure the AirPort Express (AX) to use PPPoE and you will be able to enter that information.
You will find this on the "Connect using:" drop down menu on the Internet tab in the AirPort Admin Utility.
Similar Messages
-
i just bought an airport express. i set it up and was able to be detected by my macbook, but i still cant connect wirelessly. the same goes when i tried my iphone. please help!
Is the status light green?
Your Airport device may be in Bridge Mode.
Airport Utility 6:
Open Airport Utility, select the Airport Express and click Edit. Navigate to the Network tab and change Router Mode to DHCP and NAT. Then click Update on the bottom right.
Airport Utility 5:
Open Airport Utility and click Manual Setup. Navigate to the Internet icon and change Connection Sharing to Share a Public IP Address. Then click Update on the bottom right. -
I have an Airport Express connected to my stereo and it was working without any problem.
Recently I bought an Airport Extreme to use it as my Base Unit connecting it to my DSL.
I followed the instructions of the Airport Utility, and it started working.
Suddenly, problems started happen the Airport express that was connected to the stereo , stopped working and it disappeared from the Airport Utility area , as it did not exist in the network. I tried to reset it but it did not appear in the Airport Utility page.
Apparently I have other problems with the private network that it created because I cannot use it because of problems with the password that was created. I can only use the network that I created for my guest...
I dont know if my problem is a configuration problem or there is problem with the equipment.
I read that other users where having the same problem with the Airport express , using non apple equipment as their base unit , but I thought that using the Airport Extreme was going to be compatible and no problems would happen.
What should I do?Common Problem. Common solution.
Connect your Express via ethernet cable to the Mac while other network connections on the Mac are switched OFF.
After the Express shows up, change the settings of the Express to join the existing network. Take the appr. settings.
Unplug and reconnect your Mac to the network.
Check if the Express shows up in Airport Utility
Alternative solution:
Hardreset the Express to factory settings
(while on power push the Pin next to the audio plug with a paperclip. Plug out the Express still holding down the little button then replug the Express to power and release button)
After that, the Express will show up in the Airport Utility.
Make all needed settings.
I would prefer the first solution, its easier just to plug a cat5 cable. -
Why won't my Airport Express allow internet connection on my Blu Ray when there is internet connection on my IMac?
I'm guessing you only have the modem/router supplied by your isp and the Airport Express. Is the Airport Express connected to the modem/router with an ethernet cable? If not, plug one end of the cable into an available port on the modem/router and the other end in to the WAN port, indicated with a dashed circle, on the Airport Express.
Have a nice day. -
Airport express dropping internet while streaming from computer
In the last week or so, everytime I try to stream video from my PC to my apple TV (2nd gen), my airport express (only router in my house) drops the internet connection. I thought at first it was my ISP, it then noticed it happened only when I was streaming movies from my PC ( have tried it with two different computers and same result). As soon as I stop streaming my internet kicks back in. I've restarted and reset both my Apple TV and airport express back to factory settings and still get the same result. In addition, the same problem occurs when i try to stream videos from my PC to my iPads or iPhone via the shared library. Curious if anyone has encountered this problem before and if it is a firmware problem and not a hardware problem.
SIdenote: Airplay in general has been unstable as well so I'm assuming the two problems are linked.And your reminder of the channels got it fixed. Being out in the country my internet is provided wirelessly (WISP) and I remembered after your comment that the tech who installed our receiver dish said that the internet is being broadcast on the 2.5 ghz band on channel 7 and if any issues arise change the channel to a lower number. Never had an issue till now and updated the channel to 1 and back in business. A big thanks.
-
Using 2 Airport Express stations - internet on one, stream to the other?
This has to be possible but I'm unable to find any documentation about it....
Summary:
I have 2 Airport Express base stations. One is downstairs with my cable modem and stereo - downstairs. The other is upstairs connected only to a stereo - upstairs. Is it possible to be connected to one Airport Express (downstairs) with my system and a different Airport Express (upstairs) with iTunes?
Details:
Right now, I have to disconnect from downstairs - losing my internet connection - just so I can select upstairs in iTunes and stream music upstairs. Eventually when I want to check my email, or access the internet, I have to kill my streaming music going upstairs and connect back to downstairs. I thought for some reason that both downstairs and upstairs would appear in the drop-down in iTunes regardless of what network I'm connected to with my system. But it is now obvious that it just shows only the network I'm already connected to in the drop-down.
It's frustrating that I can't be connected to both in some way. Is this even possible?
Message was edited by: pennydreadfulsInitially, I'm gonna say, "Yes." I've got a dual-band setup. I've got a AEBS (g-only) with two APEX (g-only) and an AEBS (5 GHz n-only). I can use AirTunes to stream music to both APEXs and my Apple TV.
So, if I understand your setup, Upstairs is only connected to a stereo and Downstairs is connected to your cable modem and a stereo. And your iTunes is either wireless or wired to the same network. iTunes should allow you to stream AirTunes to your computer, Upstairs, and/or Downstairs. If you want to stream to ALL three, simply select Multiple Speakers in the bottom right corner of iTunes.
Hope that helps.
Oops! I assumed that you're running one (1) network. After reading the other post, I would agree. In your situation, you need to have one of the Expresses acting as the WDS main base station and the other needs to be set to participate/join which essentially extends the network.
Message was edited by: Fabian Ramirez -
using sucessfully airport express for internet
when hooking up new airport extreme light glows green, but does NOT appear in devices sesn in 5.6 airport wifi devices
wanting to use extreme at base and express in another part of the houseHow is the express getting internet? What modem is it plugged into?
How is the extreme setup? New extreme cannot be setup with 5.6 utility.. you must use latest 6.3. Which also means you cannot setup from computer using less than Lion .. or you must use iOS with latest utility but it has limited configuration cf the computer version.
IPv6 is also needed.. turn on local link. -
Okay, well I have just bought a AirPort Express Base Station ( 2nd Generation ) and I'm new to it, but I wanted to ask that if it join's a network you have setup at home, will it still run with the 2.4 GHz and the 5.0 GHz.
The AirPort Express will "extend" both the 2.4 GHz and 5 GHz networks and provide more wireless signal coverage when it is connected to another Apple AirPort router and configured correctly.
The AirPort Express cannot provide more wireless coverage though, if you are trying to connect it to another 3rd party wireless router using wireless only.
It should be possible to set up the Express to provide more signal coverage if you connect it back to the main router using a wired Ethernet connection or using Ethernet powerline adapters. -
I downloaded and installed Airport Express Utility 5.6 to get my old Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility. What's up?
It is likely that you downloaded AirPort Utility 5.6.1. If you checked the requirements, this only runs on Leopard or Snow Leopard Macs.
You have Lion, so you need AirPort Utility 5.6 for Mac OS X Lion -
Clicking sound originating from Airport Express firmware 7.5.2 and later
Hello,
I have submitted a bug report through Apple Developer Connection (I am a registered developer). By posting this here I want to get support for our case: Make Apple fix the Airport Express firmware.
Summary:
The Airport Express device has a bug which appeared first in version 7.5.2. It produces a "clicking" sound when using AirPlay to transport music from an iPhone or a Mac, when certain frequencies are being played. This is not depending on the attached amplifier or headphones, digital or analog output, network settings (network created by Airport Express or not), Mac or iPhone used, audio cable or power supply involved or due to bad quality of the sound file played. The problems are not there when audio is played directly from a Mac or an iPhone through headphones or optical out. We and my colleagues (developers and audophiles) have ruled out all the other options. The problem boils down to a change in the Airports firmware starting with 7.5.2. In 7.4.2 the clicking sound is not there.
Steps to Reproduce:
Play the following song via AirPlay on an Airport Express device having firmware 7.5.2 or higher. The Airport Express being used in our tests is the model produced from March 2008 – June 2012. Attach high fidelity headphones (like Bowers & Wilkins P5, which we used) to Airport Express. Alternatively use a very good amplifier/loundspeaker setup. We also reproduced the bug for example on an Onkyo A-9070 amplifier with both optical and analog connection - there is no difference there. The loudspeakers we used are passive Dynaudio X12.
Play track no. 6 from the "Songs without words" album: http://itunes.apple.com/de/album/lieder-ohne-worte-op.-67-no.-2/id209380163?i=20 9381206
Listen to this solo piano piece carefully for at least 40 seconds. You will notice a clicking sound with high frequencies. This clicking is *not* there in firmwares 7.4.2 and earlier.
Expected Results:
Perfect audio quality as in firmware 7.4.2 and earlier.
Actual Results:
Reproducible clicking sounds in high frequencies.
Regression:
This problem appeared first in Airport Express firmware 7.5.2 and has not been fixed yet. It can also be observed in the current version of Apple TV (as of September 16th).
Notes:
This issue, while not being recognized by the casual listener, makes AirPlay unusable for critical listening - at least when using any firmware after 7.4.2. I would love to use the current firmware (which produces a much more stable connection), but I (and other audiophile AIrplay users) would love to see this issue fixed first.
Here is a thread that concludes - as we did - that Airport firmware 7.5.2 and later is the source of the problem. It is not the hardware, neither Apple's, nor the connected devices:
https://discussions.apple.com/message/17296916#17296916
Hope this helps!
Best,
GabrielI'm having the exact same problem. As a classical music lover, this is driving me nuts. It's especially noticable in soft passages in the music, when the volume is turned up high. When the dynamics increase, the little pops/clicks appear (they sound a bit like static noise, as someone stated earlier in this thread). It happens at irregular intervals. When you play pop music, the clicks will disappear (drown) in the music. But for true audiophiles who listen mainly to jazz and classical music this is a severe problem.
I have checked everything and it's definitely an airplay issue. My apple lossless files are 100% okay and play without any problem, except when streamed via airplay. Also, it makes no difference whether you use the analogue or the optical ouptut from the airport express.
I've created a sine frequency sweep myself in Adobe Audition, from 20 Hz up to 20000 Hz with a duration of 25 seconds and a level of -6 dB.
When played through airplay, the clicks always start to appear after 4 seconds in the sweep, only to disappear at 23 seconds.
The clicks manifest themselves at different volume levels. To my ears, they make the same sound as when you change the volume in iTunes when streaming music through airplay. Only when you set the volume in iTunes extremely low, the clicks will disappear.
Apple engineers should use a frequency sweep to recreate the problem, as this is very revealing.
PS: file format isn't an issue here. I've converted the Apple Lossless file to MP3, and it makes no difference at all. -
Hi, I`d like to connect my Ipad wirelessly to a stereo to listen to my music from the iTunes library on streaming, but also to movies online, games, Goear…) and so on. I guess I can do that using an Airport express connected to the stereo and via airplay to my Ipad. My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library? I`d appreciate any help. Alex.
My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library?
On the iPad you can stream videos, photos, or music from the Video, Photos, Music, and YouTube apps to an Apple TV OR just stream music to an AirPort Express Base Station. -
I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Any thoughts?
This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
To check and see if that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express. -
My airport express is 10 years old and I get the message that this version of airport utility (6.2) doesn't support my base station? What to do?
What to do?
Two Options:
1) Buy a new AirPort Express, which will be supported.
2) Try a workaround....not supported by Apple.....to install AirPort Utility 5.6 on the Mac using the Mountain Lion operating system and use the 5.6 application to administer the old AirPort Express. See this thread for more details:
https://discussions.apple.com/message/21397085#21397085 -
Airport Express as a Wireless Bridge and AirTunes?
I have a linksys router and just got a Tivo I was thinking of getting the Tivo wireless adapter but after much though i had a brainstorm
What if i were go get an express and hook it up as a wireless bridge (connect the Tivo to the ethernet port) and while i am at it connect my computer to my stereo system via AirTunes.
Is it possible to use the Airport Express as a wireless bridge and use airtunes at the same time while using my linksys router?To do this, you must use WDS. Very, very, very few 3rd party devices are compatible with Apple's WDS.
The Linksys WRT54G or WRT54GS (not latest versions v5) however are compatible with Apple's WDS. If you have one of those, it is possible. -
Airport express: use internet and air tunes at the same time?
Hi,
I'd like to use and airport express to create a wirelss network (and so use the internet) AND stream music to my stereo with air tunes - at the same time. Is this possible? So far, I have been able to create a wireless network (and use the internet) OR use the airport express to play music. But whenever my internet works, itune can't find the base station - claiming it "can't be found on the network?"
Can you do both at once?
I'm connecting to an ethernet jack (I'm at a college). It's not a cable modem or DSL. Is this the problem?
Under "music" in the utility configuration. I've selected "Enable Air tunes at the base station." I can't select "Enable Airtunes over ethernet port." When i try to change the network options to allow me to select this "ethernet port" option, I have to tell it how to "distribute IP" addresses. i don't know how to do this, and everything I've tried destroys my internet connection.
I appreciat any help you have to offer. thanks
1.5 GHz PowerPC G4, 12'' powerbook Mac OS X (10.4.4)solution:
My problem ended up being specific to the network I'm using. There is evidently another router on the ethernet system that was assigning my airport express an IP address (192. ...), rather than letting the network DCHP give me a direct IP address (something like 160. ...). The 192 address made it impossible for iTunes to see my express base station, but I was getting internet, passed through this other router.
The fix - and I'm not sure if this is totally kosher - was to manually enter a correct IP address for my base station. I got the IP address by seeing what this other router was sending my computer to get onto the internet. It gave me the correct router and a workable (160. ...) IP address. I'm not sure if I'm supposed to manually pick an IP address on the ethernet, but this one is working for the time being, and now iTunes can find my base station.
Maybe you are looking for
-
IPod Classic recognized by iTunes, but won't sync? (Windows 8)
iTunes recognizes it and I can go to the menu that displays the filled memory, options (enables disk use, sync only checked songs, etc.), and "sync" button. The iPod screen says that it is connected and charging, and it does not freeze. The computer
-
I've got a big trouble. First, I'm trying to do mapping using Java Coding based on the TopLink Developer's Guide. I'm using a Employee's Table as usual, but here is the problem, I can not do inserting on the database after I do mapping. As a note, th
-
Gnome 3.16 Wayland Setting Display refresh rates
In X I have done this with xrandr, but in Wayland there is no such option that I know of. What would be the way to do it?
-
How do I get my contacts to show up in Sunrise Calendar?
I recently added Sunrise Calendar to my devices, when I create an event and attempt to link it a person Sunrise does not see my contacts.
-
Does anyone know if there still any bugs in 10.7.4 because I really want to update for the reopening windows after logging in fix, but is there still bugs in the update?? Any answers will be much appreciated Thanks Sebastian