NI-5600 Usgae in RF Transceiver

Hi,
For My SDR at one stage i needed to use NI-5600 to downconvert my time domain signal from 2GHz to base band or IF. I wanted to ask how can i pass the waveform of data generated from previous step to my NI-5600 without using to generate anything using NI-5441. Moreover i also wanted to store the result in the measurment file thereafter.
Thankyou

I'm a little confused about your question. The 5600 is a downconverter that takes your frequency of interest (carrier) and down converts (or upconverts it if needed)it centered at 15MHz. Usually with a bandwidth of 20MHz. This is what comes out of the output port of the 5600... a 5 to 25MHz signal. This is considered IF.
In order to store this signal it must be digitized. In my case I use the associated 5142.
I don't understand where the 5441 Arb comes into play? Do you want to recreate your original signal?
Hope this helps.
Using LabVIEW 2010SP1 and TestStand 4.5

Similar Messages

Spectrum Frequency Error with PXIe-5641R and PXI-5600

Hello,
following situation: I am using the PXIe-5641R (in FPGA-mode) in combination with the PXI-5600 downconverter to get a spectrum.
After trying out with different span widths I've experienced strange frequency errors in the range span <10M.
To negotiate errors in my program I've evaluated also the NI example of http://zone.ni.com/devzone/cda/epd/p/id/6196 - unfortunately same error in frequency happens there.
What is meant with frequency error, for example: I have a transceiver which sends FSK with center frequency 443,92MHz. Readings with span-width = 12,5M shows overall good results.
Reading with span width smaller 10M, eg. 3,125MHz, gives unexpected readings.
With a center frequency of 433MHz and a span of 3,125MHz the transmission is out of range of spectrum. When I add an offset of 2M to the calculated IF-frequency, I get right results.
With a center frequency of 434M I've got readings at 434,92MHz, means at 1MHz too high (after adding an offset of 1M to IF freq readings are correct).
With center frequency 435MHz readings are correct. The limit between correct and wrong is exact at 434,5MHz (resulting IF = 14,5MHz) readings at that center frequency are good, just one step below (434,49MHz) readings are 1MHz too high.
Where is the error hidden? Like I said this behaviour happens also with the NI example.
Thanks for helping!
Message Edited by Lars.B on 05-20-2009 04:26 AM
Message Edited by Lars.B on 05-20-2009 04:28 AM
Message Edited by Lars.B on 05-20-2009 04:29 AM

To get closer to the problem: I've managed to get constant right results in editing the VI which calculates the IF-frequency for the IF-RIO after setting center frequency and span of PXI-5600.
But the new values make no sense at all. Documentation says that with spans higher 10MHz step size of center frequency is 1MHz, below it is 5MHz (with lower phase noise). After my modifications it seems that step size is 1MHz at all span widths higher 1MHz and 5MHz at span widths lower 1MHz.
Attachments:
Get NCO Frequency.vi ‏8 KB

K9N Platinum: upgrade to X2 5600+ or X2 6400+?

Hi. This is my first post. I would like to upgrade my CPU on my K9N Platinum and I have a couple of questions:
1. I have narrowed down to two: X2 5600+ (89w) or X2 6400+ (125w)?
- both have the same L2 cache, but the speed and wattage differ
- I play some games and some video encoding
2. Will the power supply that I have be sufficient for the X2 6400+ and support a video card upgrade to a GeForce 8800 series?
Many thanks in advance.

Quote from: Ragnor on 12-February-08, 11:22:49
but doesn't overclocking too much or running certain clock speed for too long, will shorter the cpu's life span?
I have a XP1700+ In a MSI K7N2 Delta L, which is default 1.47 and I have had it at 2.0 for nearly four years, aftermarket Copper Core air cooler. The 5000+ Blackie's that I have are at a 16 Multiplier for 3.2 speed. I have one in a abit KN9 SLI and the other in my MSI K9A2 CF both run cool. I am not overclocking my 6400+ Blackie right now, but I would expect it to have a good bit less Overclocking potential. It runs super at default though.
I had a Overclocked ATI 9500 Pro and it died after two and a half years, but I really had it cranked, so yes and no to your question. Good cooling alleviates most of the possible damage. If you are Cool then you are usually okay.

Need help in making a USGA handicapping spreadsheet for my golf group. Anybody done this?

Need help in developing a spreadsheet for my golf group using the USGA system for handicapping? Has anybody done this?

Hi Jim, if you google "golf handicapping speadsheet" you will find a lot of entries; you will find probably a solution already done.

Device not working after updating from 8 to 8.1: SMK Ehome Infrared Transceiver and remote control (usb)

Hi all,
An excellent 2015 to you all.
I wonder whether it's possible to get my (USB) SMK Ehome Infrared transceiver (which serves to connect my PC to a remote control) to work again. It functioned okay under Windows 8, but when I upgraded my system to Windows 8.1 it didn't respond anymore.
How's that possible? And do you have any ideas how I can resolve this?
I use the remote control to start and stop videos and to adjust the sound volume.
What I have done already:
-disabled and enabled the consumer IR devices under 'HID devices' in device management.
-disabled and enabled the USB controller for the Ehome Infrared Receiver.
No luck so far. Anybody knows what to do?
Cheers,
Peter

Hi,
What is the driver status in device manager? Have you tried to manually download the right version driver for Windows 8.1 from the transceiver's manufacture website and install it in your system?
Meanwhile, please run services.msc to launch services manager, then scroll down to "Human Interface Device Access service", make sure the service is "started" to "manual" or "automatic", test the issue again.
Yolanda Zhu
TechNet Community Support
Thanks, Yolanda Zhu. There is no driver on the manufacturer's website, but the driver is included from Windows versions XP to 8 and the device responds as expected under these OS Versions. In Windows 8.1 it seems also to be included, and device manager
indicates under Human Interface Devices that the 'Microsoft eHome infra transceiver' driver functions correctly and under
Universal Serial Bus controllers that 'eHome infrared receiver' (USBCIR) functions correctly as well. But when I press the remote, the red LED blinks, but nothing else happens.
The "Human Interface Device Service" is set to automatic and is being executed.
Can it be that the mapping ('action on remote' to 'action on PC') is lost somehow?
Cheers,
Peter AKA Django

HP Officejet 5600 drivers for Mavericks

Hi,
I just got a new macbook pro and installed Mavericks. Well, among a couple of problems there is one important thin:
No recognition of my HP Officet 5600 series printer. Even though is the support section of the apple.com it says it has the driver and supports this specific model, I can´t find the way of making the printer working.
Does anybody can help me solve this problem?
and how can I burn a dvd/cd if there is not support for Toast Titanium?
Oohhh Mavericks

Hello UP and away,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
Troubleshooting printer issues in OS X
http://support.apple.com/kb/TS3147
Follow these steps until the issue is addressed:
Make sure that the printer is powered on, has ink / toner, and that there are no alerts on the printer’s control panel. Note: If you cannot clear an alert on the printer's control panel, stop here and check the printer's documentation or contact the manufacturer for support.
Ensure the printer is properly connected to a USB port on the Mac or AirPort base station / Time Capsule. If the printer is a network-capable printer, make sure that it is properly connected to your home network.
Use Software Update to find and install the latest available updates. If an update is installed, see if the issue persists.
Open the Print & Scan pane or Print & Fax (Snow Leopard) pane in System Preferences.
Delete the affected printer, then add the printer again.
If the issue persists, try these additional steps:
Reset the printing system, then add the printer again.
If the issue still persists, reset the printing system again. Download and install your printer's drivers. Then, add the printer again.
Contact the printer vendor or visit their website for further assistance.
Best of luck,
Mario

How to set transceiver mode to 2-wire TXRDY Auto from Visual Basic

I am using a PCMCIA-485 adapter to interface to some RS-485 sensors. The sensors are connected using a 2-wire interface. I have developed an application in Visual Basic to control the various sensors. However, the application is dependent on the PCMCIA-485 adapter's transceiver mode being configured into the "2-Wire TXRDY Auto" mode. Presently I require the user to configure the transceiver mode by opening up the advanced setting dialog within the device driver for the adapter and manually setting the transceiver mode. I would prefer to have my application take care of this directly. Unfortunately, I cannot find any references that document how to do this.
Can I use Measurement Studio Tools for
Visual Basic to control the transceiver mode of the PCMCIA-485 adapter?

Hello-
There is a registry key in Windows that can change this mode:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Serial\Parameters\Serial1000X\TransceiverMode
Try experimenting with it by hand first. It may also be necessary to reboot after changing this value.
Randy Solomonson
Application Engineer
National Instruments

How can I scan with HP 5600 all in one?

Hi! I have an HP 5600 all in one. I recently switched to an iMac Leopard. The printer driver does not have any scanning support. Is there any other driver available to get this support? Or will I have to get a compatible printer to be able to use scanning options?
Thanks.

Have you checked the HP site, there is software for the 5600 series of all-in-one printer. Its 188Mb download that is titled "Full feature software and drivers for Mac OS X 10.3-10.5".
http://h10025.www1.hp.com/ewfrf/wc/softwareList?os=219&lc=en&dlc=en&cc=us&produc t=441123&lang=en
regards

Inspire 5600 5.1 speakers, not enough analogue inputs on receiver? help!

Hi, I need some help connecting my computer up to my Inspire 5600 speakers. I want to set up an analogue 5.1 connection, as apparently surrouund sound in many games doesn't work with optical. My problem is with the inspire 5600 receiver. It only has analogue inputs for front and rear speakers, and none for centre/subwoofer. I tried using the Creative technical support site, but for some reason my speaker set isn't listed (it has the Inspire 5200, and the I-trigue 5600, but no Inspire 5600). I checked the guides for other speaker sets to see if they were relevant, but the flash animations all show 3 analogue inputs, not the 2 that my receiver has. My speakers are a few years old, and unfortunately I don't still have the documentation that came with them.
My question is where do I plug the centre/subwoofer? Does the Inspire 5600 not actually do 5.1 for analogue? (Aside from the analogue front/rear inputs, it has an optical in, digital din and a coaxial). Does the centre/sub maybe plug into one of these instead? I'm very confused, any help would be appreciated.

Sorry I mistook it for another model, my bad. The Inspire 5.1 Digital 5600 has only two analog inputs for front and rear channels respectively. You are right, there is no orange jack on the subwoofer for this model. Last I checked, I was told that this speaker model was released before sound cards with 5.1 connections came about. So if you are doing up an analog connection, you will lose the center/subwoofer channel. However if you own a Creative sound card, you might be able to enable the CMSS feature to create a virtual surround.

Inspire 5.1 Digital 5600 - LOSE BASIC FUNCTIONALITY?

Hi all,
We will see if this gets edited. This is in addition to the original message, as I have no answers, just more questions. I have bought Creative products all my life, Ill leave it up to you in deciding wether I will in the future. If anyone actually knows a way around these problems, please let me know. Im sure I wont have a reply from Creative, but I will live in hope that I get a personally deli'vered set of speakers that adds to my options, not diminishes them!.
Well, I have XP Pro SP2, Audigy DE and just bought Inspire 5.1 Digital 5600 to upgrade from my cheaper analog 5.1 speakers that sounded OK and worked fine. I read all about the 5600's and thought - better sound, heaps of connection options etc. Their NOT exactly cheap! The point I would like to make is that I had good 5.1 sound, and now I have better sound AND A WHOLE LOT OF HASSLES IN RETURN FOR SPENDING A LOT OF MONEY. WHAT A MISTAKE.
I have THE ONLY AVAILABLE 5.1 connection from my Sound Card to the 5600 speakers, 3.5 mm 4 pole jack to din to din to speakers. (thats simple isnt it!!!) I have all the latest drivers etc, etc, etc.
NOW ...
1) If Im listening to 5.1 ie DVD, You dont get any system OR ANY OTHER sound? (Thats great for when your on the Net and need to know whats happening, isnt it's)
2) So I figure, well Ill connect the SC to the decoder using analog cables, SORRY, YOU CANT DO that unless you want to lose a channell? (for the sakes of one more center\sub jack or using all the pins in the DIN plug.)
3) Well, Ill set the mixer to do AC3 Decode to try and get back any other sound besides 5.1 Dolby, SORRY, that doent work either ... No matter how you have the decoder\Amp set up, you lose the center channel, ie, no voices?!!
4) Well Ill use the passthrough feature as it explaines in the book, SORRY, IT DOENT WORK EITHER, its meant to pass the Dolby Digital straight through to the respective channels, IT DOESNT? You lose the rear channels. I have tried every combination of everything, and you cant get ANY OTHER SOUND when you are playing Dolby Digital 5.1. so you have a "on board decoder" that NOW DOENST WORK and cant be used?
5) Why buy another 5.1 Dolby decoder when your Sound Card\Software already does it ... well I wanted to be able to use the other anolog Sound Card outputs ... SORRY, YOU CANT. When you enable the digital output only in Surround Mixer, IT DISABLES ALL THE OTHER SC output JACKS as well. GREAT!!! so you cant even feed an anolog signal in to it to try and get the "other" sound back that way? THEIR IS NO WAY!
6) All the controls .. ie... Bass Redirection, AC3 Decode, Sub Volume, Center Volume, Balance and fade controls all DONT WORK at ALL when playing 5., and the bass Redirection works backwards whith standard PCM Sound!?
7) The TEST SPEAKER function in Surround Mixer is now useless except for standard stereo. (no wonder they put a test function on the remote!)?
8) Their is bad initial distortion when you ie, fast forward, start, stop ANY Dolby Digital source?
(10 THIS IS THE BEST ONE - They DONT TELL YOU ANYWHERE about any of this stuff?, Unless Im stupid, I dont feel these speakers are fit for their purpose, is that not a condition in the Trade Practises Act? Creative, please knock on my door! and PLEASE DONT send me an Email with a "reload the drivers" pre-formatted Email, I couldnt bear the added stress!
11) How come you cant plug the Audigy straight in to the 5600 decoder with a mono cable like it says you can with every other Amp\Decoder you can buy, then they could have used the other DIN Plug Pins for anolog Audio as well and at least reatained similtanious multi sound format.
I just dont get it! Why does it have to Dolby Decode a Dolby Decoded Signal?
12) etc. etc., etc.,etc. etc., etc.,etc. etc., etc.,etc. etc., etc. ....
I could write 5 pages of all the other area where you go BACKWARDS, but I have better things to do with my time, all from a relatively expensive purchase. SO what have I ended up with ... Sure, these speakers sound OK, a bit better than my old $45 speakers, but I end up hearing one type of sound from my computer at a time with NO WAY to remedy it (inexcusable) and a second Dolby Digital decoder that I didnt need in the beginning that removes the most basic functions and I also lose the analog outputs on the sound card. Also the Dolby Digital output is about 40% quieter than "standard" PCM sound! And dont forget, be carefull, dont turn them up too loud, or you might blow the fuse and have to spend a fortune and be without speakers for weeks\months while a Technician has to to replace the fuse at great cost! (thats what they tell you in the book) And dont leave that massi've 2.5 amp power supply on all the time, that will even send you more broke trying to pay the power bill.
I have never bought a product before that removes options and useability, your money is meant to buy you these things, isnt it's? Hopefully Im just an idiot and someone will tell me this nightmare is over. By reading the other posts, I can only assume that any real posts like this are nuked in seconds, so you end up with a whole lot of useless dribble that doesnt help anyone, just wastes more of their time for spending their hard earned money. Creative, you should be ashamed of yourself, especially after such a good past record. I feel for all the stress the majority of posters have and are going through to this day. Please post this message un-edited, as it will save me having to publish it elsewhere. I do not believe it is defamitory, it is just the truth.
VERY DISSAPOINTED ... Rob ... and waiting for the Creative knock on the door!
Anyone want a BRAND NEW half price Inspire 5.1 Digital 5600 system, I dont, unless Im stupid, then Ill change my mind!!

Hi all,
We will see if this gets edited. This is in addition to the original message, as I have no answers, just more questions. I have bought Creative products all my life, Ill leave it up to you in deciding wether I will in the future. If anyone actually knows a way around these problems, please let me know. Im sure I wont have a reply from Creative, but I will live in hope that I get a personally deli'vered set of speakers that adds to my options, not diminishes them!.
Well, I have XP Pro SP2, Audigy DE and just bought Inspire 5.1 Digital 5600 to upgrade from my cheaper analog 5.1 speakers that sounded OK and worked fine. I read all about the 5600's and thought - better sound, heaps of connection options etc. Their NOT exactly cheap! The point I would like to make is that I had good 5.1 sound, and now I have better sound AND A WHOLE LOT OF HASSLES IN RETURN FOR SPENDING A LOT OF MONEY. WHAT A MISTAKE.
I have THE ONLY AVAILABLE 5.1 connection from my Sound Card to the 5600 speakers, 3.5 mm 4 pole jack to din to din to speakers. (thats simple isnt it!!!) I have all the latest drivers etc, etc, etc.
NOW ...
1) If Im listening to 5.1 ie DVD, You dont get any system OR ANY OTHER sound? (Thats great for when your on the Net and need to know whats happening, isnt it's)
2) So I figure, well Ill connect the SC to the decoder using analog cables, SORRY, YOU CANT DO that unless you want to lose a channell? (for the sakes of one more center\sub jack or using all the pins in the DIN plug.)
3) Well, Ill set the mixer to do AC3 Decode to try and get back any other sound besides 5.1 Dolby, SORRY, that doent work either ... No matter how you have the decoder\Amp set up, you lose the center channel, ie, no voices?!!
4) Well Ill use the passthrough feature as it explaines in the book, SORRY, IT DOENT WORK EITHER, its meant to pass the Dolby Digital straight through to the respective channels, IT DOESNT? You lose the rear channels. I have tried every combination of everything, and you cant get ANY OTHER SOUND when you are playing Dolby Digital 5.1. so you have a "on board decoder" that NOW DOENST WORK and cant be used?
5) Why buy another 5.1 Dolby decoder when your Sound Card\Software already does it ... well I wanted to be able to use the other anolog Sound Card outputs ... SORRY, YOU CANT. When you enable the digital output only in Surround Mixer, IT DISABLES ALL THE OTHER SC output JACKS as well. GREAT!!! so you cant even feed an anolog signal in to it to try and get the "other" sound back that way? THEIR IS NO WAY!
6) All the controls .. ie... Bass Redirection, AC3 Decode, Sub Volume, Center Volume, Balance and fade controls all DONT WORK at ALL when playing 5., and the bass Redirection works backwards whith standard PCM Sound!?
7) The TEST SPEAKER function in Surround Mixer is now useless except for standard stereo. (no wonder they put a test function on the remote!)?
8) Their is bad initial distortion when you ie, fast forward, start, stop ANY Dolby Digital source?
(10 THIS IS THE BEST ONE - They DONT TELL YOU ANYWHERE about any of this stuff?, Unless Im stupid, I dont feel these speakers are fit for their purpose, is that not a condition in the Trade Practises Act? Creative, please knock on my door! and PLEASE DONT send me an Email with a "reload the drivers" pre-formatted Email, I couldnt bear the added stress!
11) How come you cant plug the Audigy straight in to the 5600 decoder with a mono cable like it says you can with every other Amp\Decoder you can buy, then they could have used the other DIN Plug Pins for anolog Audio as well and at least reatained similtanious multi sound format.
I just dont get it! Why does it have to Dolby Decode a Dolby Decoded Signal?
12) etc. etc., etc.,etc. etc., etc.,etc. etc., etc.,etc. etc., etc. ....
I could write 5 pages of all the other area where you go BACKWARDS, but I have better things to do with my time, all from a relatively expensive purchase. SO what have I ended up with ... Sure, these speakers sound OK, a bit better than my old $45 speakers, but I end up hearing one type of sound from my computer at a time with NO WAY to remedy it (inexcusable) and a second Dolby Digital decoder that I didnt need in the beginning that removes the most basic functions and I also lose the analog outputs on the sound card. Also the Dolby Digital output is about 40% quieter than "standard" PCM sound! And dont forget, be carefull, dont turn them up too loud, or you might blow the fuse and have to spend a fortune and be without speakers for weeks\months while a Technician has to to replace the fuse at great cost! (thats what they tell you in the book) And dont leave that massi've 2.5 amp power supply on all the time, that will even send you more broke trying to pay the power bill.
I have never bought a product before that removes options and useability, your money is meant to buy you these things, isnt it's? Hopefully Im just an idiot and someone will tell me this nightmare is over. By reading the other posts, I can only assume that any real posts like this are nuked in seconds, so you end up with a whole lot of useless dribble that doesnt help anyone, just wastes more of their time for spending their hard earned money. Creative, you should be ashamed of yourself, especially after such a good past record. I feel for all the stress the majority of posters have and are going through to this day. Please post this message un-edited, as it will save me having to publish it elsewhere. I do not believe it is defamitory, it is just the truth.
VERY DISSAPOINTED ... Rob ... and waiting for the Creative knock on the door!
Anyone want a BRAND NEW half price Inspire 5.1 Digital 5600 system, I dont, unless Im stupid, then Ill change my mind!!

Sorry but I need a little help from yours...(vivo function on FX 5600)

Hi everybody, I've decided to post here in order to get some advices (maybe some of the moderators are not going to agree with me) from some of you (wonkanoby, Osnavi, Stu online, among others...) that I have the certainty that you could help me out here.
So here it's the message posted in the VGA MSI cards forum, but I didn't received any answers... And I'm so sorry for doing this but I don't see any other option, I really appreciate your advices, so here it's:
"Hi, I'm trying to use the VIVO function on a MSI Geforce FX 5600 but without any good result. I've installed the last WDM driver and also the lates Nvidia drivers, also the Info executable for Intel Chipset (inf, AGP), the motherboard can't asign an IRQ to the AGP (possible solution suggested by Nvidia itself to reponse to: "code 10 the device can't start"), I don't know if this mobo it's not compatible with this function or with this vid card. I'm pretty shure that I can't capture any video files without having the need of using any third part software (adobe premiere, capture solution, tv-christ, among others) and please advice me if I'm wrong, (I've tried MSI media Center deluxe without any success). The error code that the device manager shows is this(on nvidia WDM video Capture): Error code 10, the device can´t start.
Any ideas are welcome.
Here are the specs:
Pentium 4 HT 2.8 mhz 800 fsb
Intel 865gbf
DDR sdram 512 pc 3200 x 2
MSI Geforce FX 5600 128vtd VIVO
Driver 6.6.8.1
Driver WDM 2.2.0.0
Toshiba 80gb 7200rpm sata port
Audigy Gamer
Fax modem Conexant
4 Fan coolers
PSU 400 watts"

There may be an IRQ issue that the Intel crowd may be better suited to help with. You may have a device IRQ conflict, I've had this happen before and you have to look at your IRQ's for starters and look at slot population. The Creative card may be in a shared slot further complicating the issue or perhaps even the drivers are conflicting.
I suggest you tell us what slots are populated and post your IRQ's.
Go to Start>AllPrograms>Accessories>System Information~>Hardware Resources>IRQ's (Use the Edit menu to select all and copy, then post your IRQ's like this:
IRQ 0   System timer   OK
IRQ 1   Standard 101/102-Key or Microsoft Natural PS/2 Keyboard   OK
IRQ 4   Communications Port (COM1)   OK
IRQ 5   WinFast TV2000 XP WDM Audio Capture   OK
IRQ 6   Standard floppy disk controller   OK
IRQ 8   System CMOS/real time clock   OK
IRQ 9   Microsoft ACPI-Compliant System   OK
IRQ 11   NVIDIA nForce PCI System Management   OK
IRQ 12   PS/2 Compatible Mouse   OK
IRQ 13   Numeric data processor   OK
IRQ 14   Primary IDE Channel   OK
IRQ 15   Secondary IDE Channel   OK
IRQ 16   RADEON X800 XT Platinum Edition   OK
IRQ 17   WinFast TV2000 XP WDM Video Capture   OK
IRQ 18   Creative SB Audigy 2 ZS (WDM)   OK
IRQ 19   OHCI Compliant IEEE 1394 Host Controller   OK
IRQ 20   Standard Enhanced PCI to USB Host Controller   OK
IRQ 21   NVIDIA Network Bus Enumerator   OK
IRQ 22   Standard OpenHCD USB Host Controller   OK
IRQ 23   Standard OpenHCD USB Host Controller   OK

Problem with I-trigue 5600 . Please help!

hi,
My I-trigue 5600 worked perfectly for over 4 years. Buy recently, my rear right channel stoped working I 've tried everything : all satellites work poperly,drivers are ok, I tested it on 2 computers. There is still the same problem. Unfortunately Creative dosn't have after-guarantee service.. So, I tried to open subwoofer, but the inerity is too complicated with many areas flooded with glue or isolation. I tried also to buy another subwoofer / i believe it must have small damage , but the rest of speakers work great and the voice of subwoofer is good as well/ but there is problem with buying a subwoofer separately. Becouse there are only auctions on net.
So , what I supposed to do? Does Creative have separated spare parts to my subwoofer? Can I buy another subwoofer anywhere?
Can I replace my sub to similar from another speakers system and which one would be suitable.
I don't want to change my speakers. They are the best for me, but defect of one chanell is annoying. Really.
I wanted to buy x-fi elite pro ,but now it's pointless.
Please help me
Despere Makary

Hey! I've got the same problem with the same kind of speakers! When im listening to something volume is coming down and after a some time its coming back to its previous level! Coming back to its normal level can be forced by turning the speakers on and off! thats all i've discovered...
i also heard that some of creative speakers have kind of (f**k i dont know the word in english :P ) which works like that: when subwoofer is hot it automatially turns the volume lower to save your speakers from burning form hot :P or something like this :P
hmm... what i discovered that is no matter what i connect as source of music! effect of volume is the same
or maby you discovered the reason of this?
ps.
sory for my very unperfect english...

Trouble with I-Trigue 5600

Hi,
I have bought an I-Trigue 5600 sound system 3 days ago to connect to my onboard CMI 8738 6CH sound card, but i have notested since i installed it that the Center Speaker doesnt work well and only produces noise. Verifyed cables/connections and its all ok. I have also notested that Center and Subwoofer share the same channel, but the subwoofer seems to be working fine. Then i decided to try this speaker somewhere else and it was working as well.
If i enable the CMSS included on I-Trigue 5600 the Center speaker starts working and the system works perfectly. However, as far as i could get from the short manual creative sent me CMSS should only be used when listening to external devices such as TV sets, game consoles, etc.
I was just wondering if someone could give me a hint on this problem to help me solve this or to point me if a new sound card would kill the problem.
Note: I can't find this audio system?s on the listed support devices, what makes me impossible to get in touch with Creative support directly...

Lovepeaceguru,
If your TV is using RCA connector, you need to get a dual RCA to stereo minijack(3.5mm) cable. Have the RCA end connected to your TV and stereo minijack end to the subwoofer audio input(FRONT). Next, have the switch behind the subwoofer slide to 2CH->5.1 upmix.
Jason

Using the Bluetooth Transceiving Key with other machines

'lo
I have recently got a Bluetooth phone and I'm looking for an easy way to give my PC Bluetooth connectivity so that they can talk to each other.
I don't have an MSI motherboard in any of my machines so I'm wondering if the transceiving key (6967) would give any machine it was connected to a standard Bluetooth connection?
i.e. can I just plug it into my PC and use it to synchronize with my phone?
Any advice would be greatly appreciated.
Thanks
D.

Quote
Originally posted by dexter
PC Bluetooth connectivity so that they can talk to each other.
I there true the bluetooth in the computer can talk to the bluetooth phone? 8o

How to connect the I-Trigue 5600 to a DVD player???

I got a set of I-Trigue 5600 and thinking of connecting all 5 speakers and woofer to the back of DVD player to get the surround effect when watching DVD. The problem is I can just plug all 5 speakers to the back of the DVD player but how can I connect the sub-woofer to the DVD player as there is no cable to connect them together? Is there some sort of cable or adapter I can buy to connect them together? Thx in advance for any help!!!

have you tried that setup already?
my guess is that the subfrequencies are still combined with the front channels, and if I correct, your speakersystem will redirect them to the sub. just give it a try.
regards

NI-5600 Usgae in RF Transceiver

Similar Messages

Maybe you are looking for