NME-AIR-WLC6-K9, Cisco2911/K9, HWIC-D-9ESW and LAP1252G Config

I have searched for help on this config with no success... all over the WWW
After a few tries and improvising I got this working. A whole lot of info on this are not documented anywhere or only discussed half way.
If someone would like this config documented, drop me PM and I'll post it here.

Hello Ehud,
Looks like this could be hardware issue. Do you see the power on the NME module when you put it in?
There could be two problems:
1. The NME-WAE-502-K9 is bad. Try putting this in a different router and see if it shows up to make sure the NME module is good.
2. The SM-NM-ADPTR is bad. Try to use different adapter with NME module and see if that shows up.
3. The router slot itself is bad. try putting the adapter and NME module in different router to verify if it works.
If nothing above works, you may want to open up a TAC case for RMA creation.

Similar Messages

WLAN Clients not browsing on Cisco Wireless Controller WLC NME-AIR-WLC12-K9

HiI have a question and i need a solution and expert help.I have done a deployment which involves Security (ASA5540), Routing/voice gateway/wlc NME-AIR-WLC12-k9) and Switching (Cisco3845-ccme/k9)Below is the list of equipment used:1. Cisco ASA 5540 - which is connected at the edge to the ISP router
2. Core Switch WS-C4948E as core and DHCP Server for all VLANs
3. Access/Distribution Switches WS-C3560G-48PS-S connected as trunk to the core switch
4. Router/Voice Gateway/WLC Cisco3845-CCME/K9 - This is the voice gateway and also the WLC
5. Wireless APs AIR-LAP1242AG-E-K9 (12 qty)Here is the deployment scenario:1. G0/0 of the ASA is connected to a 7200 router from the ISP (Public IP Add)
2. G0/1 of the ASA is connected to gig 1/3 on the Core Switch on VLAN 2 which is the management VLAN (Local IP 10.1.1.2)
3. Port 3 of the Core switch is on vlan 2 connected to ASA - Management IP of Core Switch is 10.1.1.1. Core Switch is the DHCP Server for all VLANS on the network.
4. All the Access/Distribution switches are configured with IP Addresses on VLAN 2
5. Telephony Services is configured on the router and DHCP Pool for Access Points and Wireless Clients is running on the router.
6. Two DHCP pools were created on the router for APs and Wireless Clients.
7. G0/0 of the router is configured on the same network that issues dhcp ip to the AP and is connected to gig 1/1 on the core switch
8 G0/1 of the router is configured as the voice port for the IP Telephony Services and is connected to G 1/2 on the core switch1. Clients receiving DHCP IP on the Core Switch can communicate with all vlans and can browse to the Internet.
2. IP Telephony Services is running well.
3. Client on wireless can get IP from the DHCP on the router but cannot browse.I have pings from the router to the core switch and firewall, but clients connected to the wireless
cannot ping other vlans on the core switch and vice versa.The port connecting the router to the core switch is an Access Port, i have changed to to trunk but still no changes.My biggest problem now is how to make the clients on the wireless communicate with other clients on the network and be able to browse to the Internet.Below is the configs on the router and core switch.Router ConfigNimc_Voice_Router#sh run
Building configuration...
Current configuration : 10513 bytes
! Last configuration change at 13:03:55 Nigeria Mon Nov 29 2010 by admin
! NVRAM config last updated at 13:03:56 Nigeria Mon Nov 29 2010 by admin
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Nimc_Voice_Router
boot-start-marker
boot-end-marker
! card type command needed for slot/vwic-slot 0/2
logging message-counter syslog
enable secret
aaa new-model
! aaa authentication login default local
aaa session-id common
clock timezone Nigeria 1
dot11 syslog
ip source-route
ip dhcp excluded-address 10.1.12.1 10.1.12.10
ip dhcp excluded-address 192.168.1.1 192.168.1.10
ip dhcp pool LWAAP-AP
network 10.1.12.0 255.255.255.0
default-router 10.1.12.1
option 43 hex f104.c0a8.0002
dns-server 83.229.88.30 4.2.2.2 193.238.28.249
option 60 ascii "Cisco AP c1240"
ip dhcp pool Wireless
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
ip cef
no ip domain lookup
ip domain name nimc.gov.ng
ip name-server 83.229.88.30
ip name-server 193.238.28.249
ip name-server 4.2.2.2
no ipv6 cef
multilink bundle-name authenticated
voice-card 0
archive
log config
hidekeys
interface GigabitEthernet0/0
description Connection to AP
ip address 10.1.12.1 255.255.255.0
ip helper-address 192.168.0.2
load-interval 30
duplex auto
speed auto
media-type rj45
interface Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/1
ip address 10.1.2.2 255.255.255.0
duplex auto
speed auto
media-type rj45
interface FastEthernet0/0/0
no ip address
shutdown
duplex auto
speed auto
interface Serial0/1/0
no ip address
shutdown
no fair-queue
clock rate 2000000
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
interface Integrated-Service-Engine1/0
ip address 192.168.0.1 255.255.255.0
no keepalive
interface Integrated-Service-Engine1/0.15
encapsulation dot1Q 15
ip address 192.168.1.1 255.255.255.0
interface Integrated-Service-Engine1/0.100
encapsulation dot1Q 100
ip forward-protocol nd
ip forward-protocol udp 12223
ip route 10.1.0.0 255.255.255.0 10.1.1.1
ip route 10.1.1.0 255.255.255.0 10.1.1.1
ip route 10.1.2.0 255.255.255.0 10.1.1.1
ip route 10.1.3.0 255.255.255.0 10.1.1.1
ip route 10.1.4.0 255.255.255.0 10.1.1.1
ip route 10.1.5.0 255.255.255.0 10.1.1.1
ip route 10.1.6.0 255.255.255.0 10.1.1.1
ip route 10.1.7.0 255.255.255.0 10.1.1.1
ip route 10.1.8.0 255.255.255.0 10.1.1.1
ip route 10.1.9.0 255.255.255.0 10.1.1.1
ip route 10.1.10.0 255.255.255.0 10.1.1.1
ip route 10.1.11.0 255.255.255.0 10.1.1.1
ip route 10.1.12.0 255.255.255.0 10.1.1.1
ip route 192.168.0.0 255.255.255.0 10.1.1.1
ip route 192.168.1.0 255.255.255.0 10.1.1.1
no ip http server
ip http secure-server
!Core Switch Configsh run
Building configuration...Current configuration : 10622 bytes
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service compress-config
hostname Nimc_Core
boot-start-marker
boot-end-marker!
aaa new-model
aaa authentication login default local
aaa session-id common
storm-control broadcast include multicast
ip subnet-zero
no ip domain-lookup
ip domain-name nimc.gov.ng
ip dhcp excluded-address 10.1.2.1 10.1.2.10
ip dhcp excluded-address 10.1.4.1 10.1.4.10
ip dhcp excluded-address 10.1.5.1 10.1.5.10
ip dhcp excluded-address 10.1.6.1 10.1.6.10
ip dhcp excluded-address 10.1.7.1 10.1.7.10
ip dhcp excluded-address 10.1.8.1 10.1.8.10
ip dhcp excluded-address 10.1.9.1 10.1.9.10
ip dhcp excluded-address 10.1.10.1 10.1.10.10
ip dhcp excluded-address 10.1.3.1 10.1.3.10
ip dhcp pool Voice
network 10.1.2.0 255.255.255.0
next-server 10.1.2.1
option 150 ip 10.1.2.2
default-router 10.1.2.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
ip dhcp pool SF_DGs_Office
network 10.1.3.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.3.1
dns-server 81.199.3.7
lease 10
ip dhcp pool Admin_Process_Fac_Mgt
network 10.1.4.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.4.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool SF_IDD
network 10.1.5.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.5.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool Finance_Fin_Inv
network 10.1.6.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.6.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool Finance_CS
network 10.1.7.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.7.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool FF_Human_Capital_Mgt
network 10.1.8.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.8.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool FF_Legal_Services
network 10.1.9.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.9.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool SF_Procurement_Serv
network 10.1.10.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.10.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip vrf mgmtVrf
errdisable recovery cause bpduguard
errdisable recovery interval 180
power redundancy-mode redundant
spanning-tree mode mst
spanning-tree portfast bpduguard default
spanning-tree extend system-id
spanning-tree mst configuration
name xxxx
revision 1
instance 1 vlan 1-20
spanning-tree mst 1 priority 0
spanning-tree vlan 1-20 priority 0
vlan internal allocation policy ascending
interface FastEthernet1
ip vrf forwarding mgmtVrf
no ip address
speed auto
duplex auto
interface GigabitEthernet1/1
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/2
switchport access vlan 4
switchport mode access
spanning-tree portfast
interface GigabitEthernet1/3
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/4
switchport mode access
spanning-tree portfast
interface GigabitEthernet1/5
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/6
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/7
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/8
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast!
interface GigabitEthernet1/9
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/10
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/11
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/12
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/13
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/14
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/15
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/16
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/17
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/18
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/19
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/20
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/21
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/22
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/23
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/24
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/25
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/26
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/27
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/28
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/29
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/30
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/31
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfastinterface GigabitEthernet1/32
switchport access vlan 2
switchport voice vlan 4
interface GigabitEthernet1/33
switchport mode access
interface GigabitEthernet1/34
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/35
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/36
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/37
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/38
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/39
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/40
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/41
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/42
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/43
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/44
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/45
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/46
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/47
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/48
switchport trunk encapsulation dot1q
switchport mode trunk
interface Vlan1
no ip address
shutdown
interface Vlan2
description Management
ip address 10.1.1.1 255.255.255.0
interface Vlan3
description Enterprise
ip address 10.1.0.1 255.255.255.0
interface Vlan4
description Voice
ip address 10.1.2.1 255.255.255.0
interface Vlan5
description SS_DGs_Office
ip address 10.1.3.1 255.255.255.0
interface Vlan6
description Admin_Process_Fac_Management
ip address 10.1.4.1 255.255.255.0
interface Vlan7
description SF_National_Identity_Database
ip address 10.1.5.1 255.255.255.0
interface Vlan8
description Fin_Finance_Investment
ip address 10.1.6.1 255.255.255.0
interface Vlan9
description Fin_Corporate_Services
ip address 10.1.7.1 255.255.255.0
interface Vlan10
description FF_Human_Capital_Management
ip address 10.1.8.1 255.255.255.0
interface Vlan11
description FF_Legal_services
ip address 10.1.9.1 255.255.255.0
interface Vlan12
description SF_Procurement_Services
ip address 10.1.10.1 255.255.255.0
ip default-gateway 10.1.1.2
ip route 0.0.0.0 0.0.0.0 10.1.1.2
ip route 10.1.1.0 255.255.255.0 10.1.1.2
ip route 10.1.2.0 255.255.255.0 10.1.1.2
ip route 10.1.3.0 255.255.255.0 10.1.1.2
ip route 10.1.4.0 255.255.255.0 10.1.1.2
ip route 10.1.5.0 255.255.255.0 10.1.1.2
ip route 10.1.6.0 255.255.255.0 10.1.1.2
ip route 10.1.7.0 255.255.255.0 10.1.1.2
ip route 10.1.8.0 255.255.255.0 10.1.1.2
ip route 10.1.9.0 255.255.255.0 10.1.1.2
ip route 10.1.10.0 255.255.255.0 10.1.1.2
ip route 10.1.11.0 255.255.255.0 10.1.1.2
ip http server
--More--
control-plane
line con 0
stopbits 1
line vty 0 4
end
Please i need somebody to help me

I wouldn't configure an ip address on the service engine subinterface.
Try setting up a vlan interface on the router with that ip address and the subinterface will be linked to the vlan interface through the encapsulation command. A vlan interface will better work as a gateway for the wireless clients
Nicolas

Import 5508 Controller Config from NME-AIR-WLC25?

Greetings!
For 3 years now, I've been using an NME-AIR-WLC25 controller with an ever-increasing number of AP's (reaching the 25 limit a few months ago). As part of a new construction project, I'm adding 5 more AP's onto my network. As a result, I purchased a 5508 controller with a 50AP license to get me started.
My question is simple-- is it possible to import the WLC25's configuration to the 5508? I have a feeling the answer is no, but I figure it can't hurt to ask, and if I'm lucky it will save me quite a bit of time configuring this new controller.

Yes, I'm running 7.0.116.0 on the WLC25 today, so that sounds promising.
I've already downloaded the config file from the WLC25, and I did notice it looked pretty basic command-line, so I was certainly hoping that to be the case.
If the 5508 firmware is newer (I haven't even unboxed it yet), do you expect I'd run into trouble importing the old config, or should I version match first, import, then upgrade to latest?
Any other gotchas I should look out for in doing this?

How to setup NME-AIR-WLC25-K9

Hi Guys,
I have NME-AIR-WLC25-K9 module installed in cisco 3945 , can some one guide me how to access and configure this thing.
Thanks in advance.
Mohseen Patel

Hi,
Here is the configuration example on how to get the WLC up and running..
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00807112e2.shtml
here is the FAQs..
http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps6730/prod_qas0900aecd8036443b.html
Lemme know if this naswered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra

Problem boot NME-AIR-WLC12-k9

I have a ISR 3845 with NME-AIR-WLC12-K9 WLAN controller. I have problem
booting the WLAN controller. When I try to have an access to the module (service-module
Integrated-service-engine 1/0 session), it keep rebooting with the message :
Booting from Secure primary boot loader..., please wait.
I enter the ServicesEngine boot-loader (***) and I try to boot with chainloader

Not supported in LMS 3.2 according to the supported device table.
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html

I desperately to uninstall adobe reader from my Mac book air. I sent adobe reader to trash and afterwards look for internet plugs in in library but the folder is empty. Can anybody help me?

I desperately need to uninstall adobe reader from my Mac book air. I sent adobe reader to trash and afterwards look for internet plugs in library but this folder is empty in my library. Can anybody help me?

I looked for plugs in in my library but the folder internet plugs in is empty

Memory on my macbook air keeps disappearing. I have 120 gigs and I am down to 150mb without adding any files.

Memory on my macbook air keeps disappearing. I have 120 gigs and I am down to 150mb without adding any files.

Thanks...I have tried the various options and the only item of interest is that my only account on this computer says it has 102 gig of memory used up. However, when I open and look at the individual files, they add up to less than 15 gigs.

How to connect my Mac Air 13" to my Philips display with DVI and VGA ports?

How to connect my Mac Air 13" to my Philips display with DVI and VGA ports?

Use a DVI to micro-DVI adapter if you're on an original MacBook Air, and a Mini DisplayPort adapter for a newer one.
(119682)

I upload all of my photos from my iphone 5 onto my macbook air to get more space on my phone, and now whenver i try to upload it says there is no more storage or there was a problem transferring a picture. what can I do to get more space onto my iphoto?

i upload all of my photos from my iphone 5 onto my macbook air to get more space on my phone, and now whenver i try to upload it says there is no more storage or there was a problem transferring a picture. what can I do to get more space onto my iphoto? I've tried putting the pictures on flashdrives, but iphoto would no tlet me transfer.

I don't know how large the SSD (solid state hard drive) is, or how big your iPhone 5 is, but with some iPhones having 64GB and some Airs having as little as 64GB and some having as much as 512GB it's not hard to see how storing the contents of your iPhone 5 on your Macbook Air could run you out of space.
Go to the Macbook Air and bring up a finder window and pull the Go menu down and go to the Computer. Right click on the Macintosh HD and select get info. See if there is any available space on the MacBook Air. If not you are out of SSD space (you're storing more on your Macbook Air than it has storage for). I'm not sure if iTunes can store its library on an external hard drive or quite how you would make that happen. But even if you managed that, when the hard drive was disconnected, you would lose access to your library. Using a smart media card might be possible (I don't know) but it would probably be irritatingly slow. If you have a small Air and a big iPhone you might just have to find a different computer to sync to. Just remember a 64GB iPhone is a big chunk of SSD for a Macbook Air. I did it with my previous and my current Air but even my previous one had 256GB and I really just fit.

HT1338 Hi everybody..i have an enigmatic problem since i bought MacBook Air..i can't watch youtube videos and i did install the latest adobe flash player BUT when i start to install it the system keeps asking me to enter a password ? which password i need

Hi everybody..i have an enigmatic problem since i bought MacBook Air..i can't watch youtube videos and i did install the latest adobe flash player BUT when i start to install it the system keeps asking me to enter a password ? which password i need ??????

Your admin account password.

I just bought a MBA and I need to move my photos and itunes to an external hard drive (from my old MacBook Pro) because they won't fit on the Air. I got the photos moved fine and I followed an online tutorial to move the necessary files for itunes, but i

I just bought a MBA and I need to move my photos and itunes to an external hard drive (from my old MacBook Pro) because they won't fit on the Air. I got the photos moved fine and I followed an online tutorial to move the necessary files for itunes, but it didn't work. The files copied fine, but when I tell iTunes on the Air to look at the external drive for the library, it doesn't find anything. What I copied was the entire iTunes Media folder. So, how do I move the necessary iTunes files from my old Pro to a external drive so I can access them from my new Air? Whew!

iTunes- How to move the library to an EHD
After you move the library you need to open iTunes by first depressing the OPTION key then launching iTunes. You will be given a choice of which library to use. This can then be made a permanent change, if you wish, in the Advanced section of iTunes preferences.

I have a MacBook Air w/ 64 GB. I have hours and hours of music/vids/etc. Is it possible to have an external drive specifically set-up for my iTunes? If so, what do I need to do? Thanks!

I have a MacBook Air w/ 64 GB. I have hours and hours of music/vids/etc. Is it possible to have an external drive specifically set-up for my iTunes? If so, what do I need to do? Thanks!

Yes, many people do just that. Copy your iTunes folder to the external drive. Once done, open iTunes with Option held down and select the new location of the library file.

I have just upgraded from a Macbook to a Macbook Air. I have been using a iomega external hard drive for Time Machine, which use a Firewire. However, Macbook Air's do not have a Firewire port and i cannot find an adaptor anywhere. Can anyone help?? Thanks

I have just upgraded from a Macbook to a Macbook Air. I have been using a iomega external hard drive for Time Machine, which use a Firewire. However, Macbook Air's do not have a Firewire port and i cannot find an adaptor anywhere. Can anyone help?? Thanks

There has never been a reliable firewire ---> USB adapter suitable for external high speed storage. This was a major issue when the MacBooks lost the firewire port a number of years ago (Apple subsequently brought it back).
The only high speed port on the Air is the ThunderBolt port. There are external ThunderBolt drive options out there, but they're somewhat more expensive than traditional USB/FireWire options.

-1007f cannot get the Mac book air to reinstall, no drive. For disk and no connection

-1007f cannot get the Mac book air to reinstall, no drive. For disk and no connection please help!!

You can download the product from this link:
<Download Photoshop Elements products | 13, 12, 11, 10>
Your redemption code/Serial number will work with these downloaded products.
Make sure you download the correct version for your operating system - Windows or Apple MAC
Good luck.

I have a work Mac, an air book, a home Mac; husband has desktop and laptop. That makes 5. My work computer was replaced and I do not know what the company did with it. I am not allowed to deauthorize all. Any way around the year limit?

I have a work Mac, an air book, a home Mac; husband has desktop and laptop. That makes 5. My work computer was replaced and I do not know what the company did with it. I am not allowed to deauthorize all because I did this within the last year when I got my new airbook. Any way around the year limit? I don't know if I can find my old computer and I don't want to wait months to be able to play my ituens purchases on my new work computer.

If oyu already used up your "deauthorize all" option, you need to contact support so they can make an excemption:
http://www.apple.com/support/itunes/contact/

NME-AIR-WLC6-K9, Cisco2911/K9, HWIC-D-9ESW and LAP1252G Config

Similar Messages

Maybe you are looking for