No Internet access when easy vpn tunnel is down.

Hi.
I have an error. i have a 819 router. with a Easy vpn tunnel.
And i am using the Identical Addressing feature, where i nat vlan1 over loopback0
I also have a vlan2 where i dont use identical addressing.
I have the Easy vpn tunnel configured on loopback0 and vlan2
from Vlan1 i nat to looopback0 with
ip nat inside source static Network 192.168.250.0 192.168.5.0 /24
and i nat outside with
ip nat inside source list INET interface GigabitEhternet0 Overload
ip access-list extended INET
permit ip 192.168.5.0 0.0.0.255 any
When tunnel is up, there is internet from vlan1, vlan2 and loopback0
But when the tunnel is Down, i can only get internet from Vlan2 and loopback0
The route for the tunnel is 0.0.0.0, i need all data to go to the vpn when its up. and to the internet when its Down.
Any ideas?
Thanks.

That is correct.
Config.
controller Cellular 0
no cdp run
track 1 ip sla 1 reachability
default-state up
ip tcp synwait-time 10
ip ftp source-interface Vlan1
ip ssh rsa keypair-name Router.yourdomain.com
crypto ipsec client ezvpn VPN-Cel
connect auto
group VPN key -key-
mode network-extension
peer 12.12.12.12
virtual-interface 1
username RouterCel password Password
xauth userid mode local
crypto ipsec client ezvpn VPN-Eth
connect auto
group PANTst key -key-
backup VPN-Cel track 1
mode network-extension
peer 12.12.12.12
virtual-interface 1
username Router password Password
xauth userid mode local
interface Loopback0
ip address 192.168.6.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip virtual-reassembly in
crypto ipsec client ezvpn VPN-Cel inside
crypto ipsec client ezvpn VPN-Eth inside
interface Cellular0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip inspect CCP_LOW out
ip virtual-reassembly in
ip verify unicast reverse-path
encapsulation slip
load-interval 30
dialer in-band
dialer idle-timeout 0
dialer string hspa-R7
dialer-group 1
no peer default ip address
async mode interactive
crypto ipsec client ezvpn VPN-Cel
interface FastEthernet0
no ip address
interface FastEthernet1
switchport access vlan 2
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface GigabitEthernet0
ip dhcp client route track 1
ip address dhcp
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip inspect CCP_LOW out
ip virtual-reassembly in
duplex auto
speed auto
crypto ipsec client ezvpn VPN-Eth
interface Serial0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
shutdown
clock rate 2000000
interface Virtual-Template1 type tunnel
no ip address
ip nat outside
ip virtual-reassembly in
tunnel mode ipsec ipv4
interface Vlan1
ip address 192.168.250.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
no autostate
interface Vlan2
ip address 192.168.16.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
no autostate
crypto ipsec client ezvpn VPN-Cel inside
crypto ipsec client ezvpn VPN-Eth inside
interface Dialer2
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip local policy route-map myRoutes
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list INTERNET interface GigabitEthernet0 overload
ip nat inside source static network 192.168.250.0 192.168.6.0 /24
ip route 0.0.0.0 0.0.0.0 Cellular0 254
ip route 8.8.4.4 255.255.255.255 Cellular0
ip access-list extended INTERNET
permit ip 192.168.6.0 0.0.0.255 any
permit ip 192.168.16.0 0.0.0.255 any
ip sla auto discovery
ip sla 1
icmp-echo 8.8.8.8 source-interface GigabitEthernet0
ip sla schedule 1 life forever start-time now
dialer-list 1 protocol ip list 1
dialer-list 2 protocol ip permit
route-map myRoutes permit 10
match ip address 101
set ip next-hop dynamic dhcp
access-list 1 permit any
access-list 23 permit 12.12.12.12
access-list 23 permit 192.168.0.0 0.0.255.255
access-list 101 permit icmp any host 8.8.8.8 echo
control-plane

Similar Messages

Cascaded routers: no internet access when second router not use NAT

Cascaded routers: no internet access when second router not use NAT
Here is my setup:
[pre]
WAN
|
| 74.96.170.x (WAN IP) |
| Router1(Verizon FiOS Router) |
| Model: MI424WR-GEN2 (Rev F) |
| Firmware: 20.21.0.2 |
| Def router: 74.96.170.1 |
| 192.168.1.1 (Local IP) |
|
| 192.168.1.22 (WAN IP) |
| Router2(Linksys) |
| Model: WRT54GL v1.1 |
| Firmware: v4.30.16 |
| Def Router: 192.168.1.1 |
| 192.168.2.1 (Local IP) |
|
| Computer 192.168.2.160 |
| Def Router: 192.168.2.1 |
"q.route" 120L, 4441C written
[m.wang@m-wang-ltm2:/Users/m.wang/m/Network]
$ more q.route
Cascaded routers: no internet access when second router not use NAT
Here is my setup:
[pre]
WAN
|
| 74.96.170.x (WAN IP) |
| Router1(Verizon FiOS Router) |
| Model: MI424WR-GEN2 (Rev F) |
| Firmware: 20.21.0.2 |
| Def router: 74.96.170.1 |
| 192.168.1.1 (Local IP) |
|
| 192.168.1.22 (WAN IP) |
| Router2(Linksys) |
| Model: WRT54GL v1.1 |
| Firmware: v4.30.16 |
| Def Router: 192.168.1.1 |
| 192.168.2.1 (Local IP) |
|
| Computer 192.168.2.160 |
| Def Router: 192.168.2.1 |
| NO iptables, basic setup |
[/pre]
On computer, I have:
[pre]
# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 192.168.2.1 0.0.0.0 UG 2 0 0 enp2s0
loopback localhost 255.0.0.0 UG 0 0 0 lo
192.168.2.0 * 255.255.255.0 U 0 0 0 enp2s0
[/pre]
On Router2, I have:
[pre]
Routing Table Entry List
Destination LAN IP | Subnet Mask | Gateway | Hop Count | Interface
192.168.2.0 255.255.255.0 0.0.0.0 1 LAN & Wireless
192.168.1.0 255.255.255.0 0.0.0.0 1 WAN (Internet)
0.0.0.0 0.0.0.0 192.168.1.1 1 WAN (Internet)
[/pre]
Router2's Operating Mode is Gateway. On Router1, I have:
[pre]
[Router1] Routing Table
Name Destination Gateway Netmask Metric Status
Network (Home/Office) 192.168.2.0 192.168.1.22 255.255.255.0 0 Applied
Network (Home/Office) 192.168.1.0 192.168.1.1 255.255.255.0 0 Applied
Routing Protocol: Internet Group Management Protocol (IGMP)
Default Gateway: 74.96.170.1
[/pre]
On computer, I can run tcptraceroute to yahoo.com OK:
[pre]
# tcptraceroute yahoo.com
Selected device enp2s0, address 192.168.2.160, port 46596 for outgoing packets
Tracing the path to yahoo.com (206.190.36.45) on TCP port 80 (http), 30 hops max
1 192.168.2.1 0.610 ms 0.729 ms 0.735 ms
2 192.168.1.1 1.843 ms 1.378 ms 1.363 ms
3 l100.washdc-vfttp-107.verizon-gni.net (96.241.146.1) 13.620 ms * *
... /* It reached the destination. */
[/pre]
I want to change Router2's Operating Mode from "Gateway" to "Router" because I
want to turn off NAT on Router2 so that I can access all computers attached to
Router2 by their individual IP instead of using port forwarding at Router2.
The problem is after the mode change from "Gateway" to "Router", and regardless
whether I disable RIP or enable RIP, and on what interfaces it is enabled, computer
192.168.2.160 does not have internet connection.
Observations:
[0] INTRAnet works as I can reach computer 192.168.2.160 from computer behind Router1
192.168.1.x and vice versa.
[1] ping and traceroute *work* on Router2 itself using the built-in dianostic tool.
[2] nslookup on computer 192.168.2.160 always works on new lookup. It uses
192.168.2.1 as the resolver.
[3] tcptraceroute stops after step 2:
[pre]
# tcptraceroute yahoo.com
Selected device enp2s0, address 192.168.2.160, port 45999 for outgoing packets
Tracing the path to yahoo.com (98.139.183.24) on TCP port 80 (http), 30 hops max
1 192.168.2.1 2.553 ms 0.534 ms 0.638 ms
2 192.168.1.1 1.342 ms 0.964 ms 0.867 ms
3 * * *
[/pre]
[4] tcpdump shows that computer 192.168.2.160 tries to reach out and nothing is returned:
[pre]
13:34:03.172828 IP 192.168.2.160.45999 > 98.139.183.24.http: Flags [S], seq 1122548929, win 0, length 0
13:34:06.175786 IP 192.168.2.160.45999 > 98.139.183.24.http: Flags [S], seq 1122548929, win 0, length 0
13:34:09.178804 IP 192.168.2.160.45999 > 98.139.183.24.http: Flags [S], seq 1122548929, win 0, length 0
[/pre]
This is not expected because NAT to internet should still be done by Router1, no? Computer
behind Router1 with IP 192.168.1.x has internet connection.
[5] It looks like I cannot change the Routing Table Entry on Router2. I do not think I need to change anything,
just an observation.
[6] If I use LAN to LAN connection, then both intranet and internet works. [The internet IP of Router2 can be
anything not in the same subnet of the Router1, and DHCP on the local side should be disabled to avoid conflict
with the the DHCP on Router1].

I have a question. Unfortunately in order to ask my question, I have to have a lengthy description of my setup. Basically, I have a second Linksys router in "router" operating mode with NAT disabled connected to the Verizon router, and I have a computer which is in a different subnet (192.168.2.x) behind the Linksys router. This computer can communicate with computers behind Verizon router in subnet (192.168.1.x), but cannot reach internet. This is a simplified version of my question, full details are in the original post.
If I setup the Linksys router in "gateway" operating mode, which means with NAT enabled, then both intranet and internet works, but there is no easy way to setup port forwarding for 10 compueters in 192.168.2.x network to communicate with 10 computers in 192.168.1.x network.
If I setup the Linksys router in a LAN to LAN configuration with Verizon routers, but this way all computers are in the same subnet, I want them to be in different subnet for access control and things like that.
I hope this makes things a little clear.
Thanks.

Im trying to restore my imac as im selling it. Ive followed advice from the internet where when you start it hold down on 'alt' until 2 disks appear but this never happens. I went into Disk Utlity to earse but the earse button is shaded out so it wont let

Im trying to restore my imac as im selling it. Ive followed advice from the internet where when you start it hold down on 'alt' until 2 disks appear but this never happens. I went into Disk Utlity to earse but the earse button is shaded out so it wont let

What OSX was installed when you purchased your Mac? Even though it was installed you should have received the install disk(s) as the Utilities are on those.
If you do not have the install disk you can try contacting Apple and see if they can supply one,(explain you never received at purchase) you will need the build info of your machine, which can be found by clicking the Apple logo in the menu bar>About This Mac>More Info, and it should be in the first window under hardware overview. Model Identifier.
Customer Support:
800-767-2275
Erase instructions
http://support.apple.com/kb/HT3910

Problems when trying to surf the Internet through a SSL VPN tunnel

Hi,
I have a small/big problem, I have a customer who have the need for the possibility to surf the internet through the SA500W when they are connected through a SSL VPN tunnel in to their network. I am not using a Split Tunnel. What I have seen until now, when you run IPCONFIG/ALL the default gateway for the SSL VPN IP settings is 0.0.0.0. Is this the problem and if so, how can this be solved?
Thanks in advance!
Brg
Niklas Eklov

There are various causes for this error, see [[Firefox is already running but is not responding]] for details.

No internet access when "Send All Traffic" VPN Checked

Hi Ladies and Gents
Wonder if you can help me. These past few days I have been setting up a VPN on my DD-WRT enabled router. I have successfully accomplished such task, however when I'm connected to the VPN on my phone my public IP address does not change, after doing some reading I believe that is because "Send All Traffic" is unchecked in the VPN profile, but when I check "Send All Traffic" I get no internet access what so ever.
Any advice/input/solution to this would be greatly appreciated.
Cheers
Cameron

Cammy1230 wrote:
when I'm connected to the VPN on my phone my public IP address does not
it's not supposed to.

No Internet access after cisco vpn client connection

Hi Experts,
Kindly check below config.the problem is vpn is connected but no internet access
on computer after connecting vpn
ASA Version 8.0(2)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Ethernet0/0
nameif outside
security-level 0
ip address 192.168.10.10 255.255.255.0
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.14.12 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
access-list dubai_splitTunnelAcl standard permit 192.168.14.0 255.255.255.0
access-list INSIDE_nat0_outbound extended permit ip any 192.168.14.240 255.255.2
55.240
pager lines 24
mtu inside 1500
mtu outside 1500
ip local pool testpool 192.168.14.240-192.168.14.250
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list INSIDE_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.14.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set setFirstSet esp-3des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set setFirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
username testuser password IqY6lTColo8VIF24 encrypted
username khans password X5bLOVudYKsK1JS/ encrypted privilege 15
tunnel-group mphone type remote-access
tunnel-group mphone general-attributes
address-pool testpool
tunnel-group mphone ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:059363cdf78583da4e3324e8dfcefbf0
: end
ciscoasa#

Hi Harish,
Please check the o/ps below and route print in attached file
Latest ASA Config
ASA Version 8.0(2)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Ethernet0/0
nameif outside
security-level 0
ip address 192.168.10.10 255.255.255.0
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.14.12 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
access-list dubai_splitTunnelAcl standard permit 192.168.14.0 255.255.255.0
access-list INSIDE_nat0_outbound extended permit ip any 192.168.14.0 255.255.255
.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip local pool testpool 192.168.15.240-192.168.15.250
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.14.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set setFirstSet esp-3des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set setFirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
no crypto isakmp nat-traversal
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
group-policy mphone internal
group-policy mphone attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value dubai_splitTunnelAcl
username testuser password IqY6lTColo8VIF24 encrypted privilege 15
username testuser attributes
vpn-group-policy mphone
username khans password X5bLOVudYKsK1JS/ encrypted privilege 15
username khans attributes
vpn-group-policy mphone
tunnel-group mphone type remote-access
tunnel-group mphone general-attributes
address-pool testpool
tunnel-group mphone ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:12308d7ff6c6df3d71181248e8d38ba8
: end
ciscoasa#
Route Print after vpn connection
C:\>route print
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x40003 ...00 24 01 a2 e6 f1 ...... D-Link DFE-520TX PCI Fast Ethernet Adapter -
Packet Scheduler Miniport
0x250004 ...00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter - Packet Schedule
r Miniport
===========================================================================
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.10.1 192.168.10.211 20
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.10.0 255.255.255.0 192.168.10.211 192.168.10.211 20
192.168.10.211 255.255.255.255 127.0.0.1 127.0.0.1 20
192.168.10.255 255.255.255.255 192.168.10.211 192.168.10.211 20
192.168.14.0 255.255.255.0 192.168.15.1 192.168.15.240 1
192.168.15.0 255.255.255.0 192.168.15.240 192.168.15.240 20
192.168.15.240 255.255.255.255 127.0.0.1 127.0.0.1 20
192.168.15.255 255.255.255.255 192.168.15.240 192.168.15.240 20
213.42.233.97 255.255.255.255 192.168.10.1 192.168.10.211 1
224.0.0.0 240.0.0.0 192.168.10.211 192.168.10.211 20
224.0.0.0 240.0.0.0 192.168.15.240 192.168.15.240 20
255.255.255.255 255.255.255.255 192.168.10.211 192.168.10.211 1
255.255.255.255 255.255.255.255 192.168.15.240 192.168.15.240 1
Default Gateway: 192.168.10.1
===========================================================================
Persistent Routes:
None
C:\>
C:\>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : asu
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection 7:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : D-Link DFE-520TX PCI Fast Ethernet A
dapter
Physical Address. . . . . . . . . : 00-24-01-A2-E6-F1
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.10.211
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.10.1
DNS Servers . . . . . . . . . . . : 213.42.20.20
195.229.241.222
Ethernet adapter Local Area Connection 8:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Cisco Systems VPN Adapter
Physical Address. . . . . . . . . : 00-05-9A-3C-78-00
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.15.240
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :

No internet access when i use my notebook into a router

I am trying to use my notebook as a repeater.
I enabled the MS Virtual WiFi Miniport Adapter and configured it with a SSID and password.
The connection seems to be alright, but when connecting my phone to this connection, I get no internet access (the phone is connected and receives an IP with no problem, but when trying to connect to the internet, as if there is no connection).
I am running windows 7

I am trying to use my notebook as a repeater.
I enabled the MS Virtual WiFi Miniport Adapter and configured it with a SSID and password.
The connection seems to be alright, but when connecting my phone to this connection, I get no internet access (the phone is connected and receives an IP with no problem, but when trying to connect to the internet, as if there is no connection).
I am running windows 7
wifi repeaters are specialized and its cheaper and easier to get one on ebay, they are low cost and are popular to deal with dead spots with wifi both with business and homes alike
Corsair Carbide 300R with TX850V2
Asus M5A99FX PRO R2.0 CFX/SLI
AMD Phenom II 965 C3 Black Edition @ 4.0 GHz
G.SKILL RipjawsX DDR3-2133 8 GB
EVGA GTX 660 Ti FTW Signature 2 (GK104 Kepler)
Asus PA238QR IPS LED HDMI DP 1080p
ST2000DM001 & Windows 8.1 Professional x64
Microsoft Wireless Desktop 2000 & Wacom Bamboo CHT470M
Place your rig specifics into your signature like I have, makes it 100x easier to understand!
Hardcore Games Legendary is the Only Way to Play!

No Internet access when I use a certain static IP yet other IP's are ok.

Hiya,
Strange IP issue !!!
I have a windows 2003 sevrer with a static IP.
My network has a DHCP server and that Particular IP is in the exclusion range.
When I open a browser on the server I get the error "internet explorer cannot display the webpage"
However if I change the static IP address to a defferent static Ip address everything works fine.
Here's the funny bit.
If I set a different PC to this troublesome static IP I also get the issue.
So the problem is with the Static IP address itself?
On the DHCP server there is no indication that this is a BAD IP ADDRESS etc..
Checkeded the firewall an this is not blocking either.
Any ideas why this particular IP fails to get me internet access ?
Ray..

IP with no internet access (IP Issue)
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet
   Physical Address. . . . . . . . . : 00-14-5E-BD-C2-0C
   DHCP Enabled. . . . . . . . . . . : No
   IP Address. . . . . . . . . . . . : 10.1.3.150
   Subnet Mask . . . . . . . . . . . : 255.255.254.0
   Default Gateway . . . . . . . . . : 10.1.2.254
   DNS Servers . . . . . . . . . . . : 10.1.3.145
                                       10.1.3.146
IP with internet access working (Normal IP)
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet
   Physical Address. . . . . . . . . : 00-14-5E-BD-C2-0C
   DHCP Enabled. . . . . . . . . . . : No
   IP Address. . . . . . . . . . . . : 10.1.3.167
   Subnet Mask . . . . . . . . . . . : 255.255.254.0
   Default Gateway . . . . . . . . . : 10.1.2.254
   DNS Servers . . . . . . . . . . . : 10.1.3.145
                                       10.1.3.146
DNS Server
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2
   Physical Address. . . . . . . . . : 00-14-5E-BD-CB-20
   DHCP Enabled. . . . . . . . . . . : No
   IP Address. . . . . . . . . . . . : 10.1.3.145
   Subnet Mask . . . . . . . . . . . : 255.255.254.0
   Default Gateway . . . . . . . . . : 10.1.2.254
   DNS Servers . . . . . . . . . . . : 10.1.3.145
   Primary WINS Server . . . . . . . : 10.1.3.145

Centralize internet access in MPLS VPN

Can i implement Centralize internet access (the Hub CE Router to performs NAT) in cisco MPLS VPN solution?
If so, is there any example about that? i can't find it at CCO~
Thanks a lot~

If you run dynamic routing protocol in PE-CE,like rip2,ospf,bgp,do the following task.
1:set a default route in HUB CE;and generate the default route under its dynamic protocol.
2:in other CEs, make sure they can learn this route.
If you run static route and vrf static route between CE and PE,do the following task.
1.set default route in HUB CE, and set default route in other CEs.
2.In all PEs,redistribute the connected and static rotues to address-family ipv4 of customer vrf.
3.set the customer vrf default route in all PE which connected your all CEs.
Note: make sure all PEs can reach the GW address of vrf deafult route. GW IP address is the interface of which HUB CE towards PE.
command: "ip route vrf 0.0.0.0 0.0.0.0 global.
TRY

Why does it say no internet access when I connect my laptop to my personal hotspot IPhone 5S?

Every time I try to go on a webpage it says no internet access on the Internet bars

Hi, jon.baldauf.
These articles will help you troubleshoot the issue that you are experiencing when attempting to connect to the iTunes Store. Make sure after each troubleshooting steps to test the results.
iTunes for Windows: iTunes Store connection troubleshooting
http://support.apple.com/kb/ht1527
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/ts3297
There is a possibility that security software installed could be the cause of the issue. You may have to process the steps in this article.
iTunes: Troubleshooting security software issues
http://support.apple.com/kb/TS3125
Cheers,
Jason H.

Able to connect ipad 2 to iphone 4s personal hotspot via bluetooth or wifi, but no internet access when connected via wifi.

I am able to connect my ipad 2 to an iphone 4s personal hotspot via bluetooth or wifi. The problem is that I only have internet access with a bluetooth connection. Both are running ios 6.1.2 and I have tried to reset both to factory settings. Any suggestions would be reatly appreciated.

Please don't shout! Using all uppercase means shouting on the internet. If your keyboard is stuck please say so, otherwise people will think you are being obnoxious.
Now the first question is, when you are saying connecting to personal hotspot, have you always been using the iPhone to connect to the internet? Are you someplace where the only place to connect is available via tethering to the iPhone's celluar network? Or do you have other options?

Does a device need constant internet access when using Adobe products?

If a user wants to use photoshop on a device that is not 1)on an network 2) does not have internet access. Is this a problem when launching the program?

Hi CarolynHayden,
No. Your application are installed directly on your computer, so you won't need an ongoing Internet connection to use them on a daily basis.
An Internet connection is required the first time you install and license your desktop apps, but you can use the apps in offline mode with a valid software license.
Please let us know if this was helpful.
Regards

IPad Internet access when WiFi and Cellular features are disabled

Local security policies require me to disable all wireless communications on devices operating within specific “Controlled Access” areas. Is there a specific lightning (cable) adapter I could use to connect an iPad device to a hardwired Ethernet cable (CAT-5 or 6) to facilitate wired internet communications in this situation? Alternately, can I use a standard Lightning-to-USB cable connected to a MacIntosh computer and somehow configure the MacIntosh to act as a router-like device for internet communications between the iPad and other intranet or internet endpoints that the MacIntosh is also able to interact with? Basically, I need to establish internet connectivity to/from the iPad without the use of wireless communications options, and I'm interested in the options I could pursue.

Thanks for the YouTube links bobseufert.
I'm going to try this approach out myself (just to verify that it works), but I'm really hoping that another - less encumbered, approach can be found for my end-goal. The larger-scale view of my need includes connecting multiple iPads (one per workstation area) to a local intranet. Since I can't use a WiFi or any other wireless communications solution for this installation, I might need a collection of adapter cables and powered USB hubs if I choose to implement the options detailed in these two videos on a large scale. Sure, that's all possible, but what I'm really hoping to find somewhere is an RJ-45 configured Ethernet-to-Lightning Adapter that will work with iOS devices.
From one perspective I can see why this type of adapter has not been built yet. However when you think about the wired adapter options that are available to connect the iPad/iPhone to a remote display (or overhead projector) - there is at least three different versions available through Apple, even through Apple sells wireless video display capabilities (I own two Apple TV devices myself), you wouldn't think that a wired network option for these mobile devices would be something out of the question...
BTW, I noted that Redpark (www.redpark.com) has some serial (RS-232) adapters for the older 30-pin iPads/iPhones and for the newer Lightning equipped iPads/iPhones that Apple has signed-off on. Redpark also has an RJ-45 to Lighting Adapter, but this particular implementation is built (i.e., wired) for the CISCO Console port, which is not compatible with your typical CAT-5 / CAT-6 wiring configuration.
If anyone else finds a Lightning Adapter providing both Ethernet-based Data (via an RJ-45 connector) and Power to keep the iPad devices charged (24/7) I would really like to hear about it... Thanks for your continued support!

Why do I not have internet access when my phone says it's on LTE?

I am currently having internet connectivity issues. My phone will say it's on LTE, but when I try to use an app that requires internet connectivity, it says that I need to check my internet connection. I can't refresh facebook, check e-mails, or send iMessages. When I join a Wifi network, everything works as it should. I've tried doing a soft reset on my phone multiple times by holding the home and sleep button down until the phone reboots. I've also restored network settings, but nothing seems to be helping. Just wondering if anyone had any tips before I had to take it into the Verizon store.

meganweers,
I am sorry you are having these issues with accessing the internet on your device. Thank you for all the troubleshooting you have done thus far. Have you tried to remove and reinsert the SIM? http://vz.to/1irq2bL Are you able to send text messages and use voice just fine? Are there others reporting the same issues with data connection?
LindseyT_VZW
Follow us on Twitter @VZWSupport

Internet access when account is suspended

My son goes to school with a really nice kid who's single mom is unemployed, and has been for a while. She doesn't seem to be trying very hard to find a job and is constantly posting on Facebook about her financial problems. People always come through with money. We are beginnning to think she's scamming people, because a lot of things she says don't add up--like this latest Facebook post: "This is weird. So I lost my Verizon this morning, no phone, no t.v. and the only internet I can get to is facebook!! Everything else goes to a notice that my account is suspended! So, I can't do anymore job hunting. This totally sucks!" How is this even possible? I could see leaving an open portal to Verizon in order to connect with them about paying the bill, but Facebook?

Geekmama wrote:
My son goes to school with a really nice kid who's single mom is unemployed, and has been for a while. She doesn't seem to be trying very hard to find a job and is constantly posting on Facebook about her financial problems. People always come through with money. We are beginnning to think she's scamming people, because a lot of things she says don't add up--like this latest Facebook post: "This is weird. So I lost my Verizon this morning, no phone, no t.v. and the only internet I can get to is facebook!! Everything else goes to a notice that my account is suspended! So, I can't do anymore job hunting. This totally sucks!" How is this even possible? I could see leaving an open portal to Verizon in order to connect with them about paying the bill, but Facebook?
What she's describing makes no sense. I suspect that when your service is turned off for non-payment, everything goes, and you have to call and make arrangements or access MyVerizon some other way than your own Internet service.
Did I read the word scam?

No Internet access when easy vpn tunnel is down.

Similar Messages

Maybe you are looking for