No signal after successful Bios and ME flash

Hi everyone,
I just build my first PC in about ten years deciding to get back into PC gaming but have encountered some problems.
My Build:
MSI Z87i-AC
Intel G3258
2 x 4GB HyperX Fury
Antec 550vp PSU
MSI Power OC gtx 670
After I completed the build all seemed well. It fired up no problem and before long i was installing the OS. However during OS installation after the computer restarted i had no signal to the monitor. I left it like that for about 20 mins then just turned it off. When I booted it back up I had no problems and Windows had installed successfully. Anyway, to cut it short. The computer worked absolutely fine If i shut it down or turned it off but if I manually reset or reset after installing programs etc there was no signal.
I found someone online with the exact same problem so I thought thats would be it sorted. Their solution, (from MSI Support was to update the BIOS and ME to support the Haswell refresh. After this the user's problem was resolved. So I followed the MSI instructions on how to update the BIOS and ME via Mflash and went ahead and done it. It didn't take long and the computer showed a message that the BIOS update was successful and would restart in five seconds.
After the restart it was straight to a no signal screen and no matter what I've tried this is how it remains. The Usb ports don't supply power to my keyboard or usb sticks either. I'm completely stuck!
I've tried switching the ram, using only one stick, a different PSU, with or without gpu etc but still just no signal.
Like I said everything worked great (apart from not being able to restart) before the BIOS update. I was on BIOS 1.5 originally and updated to 1.9.
Thanks for reading!

Ok so I've tried clearing the cmos how you suggested and still nothing... I also tried various other methods from the forums but still just no signal.
I'm completely stuck now as the only probably thing seems like the motherboard is dead I don't think any other hardware could be the problem as it worked fine until the bios flash.
Should i just RMA the board and go for something else?

Similar Messages

Runtime error after successful compile and link with cl.exe

Finally, got the configuration for cl.exe and link.exe right and got a successful compile and link to produce a dll. Then ran the main method of my Java class. The main method calls the constructor, and loading the class runs the static block which loads the native dll. I get one of those error files of the type hs_err_pid4064.log. The file is as follows:
# An unexpected error has been detected by Java Runtime Environment:
# Internal Error (0xe06d7363), pid=4064, tid=3576
# Java VM: Java HotSpot(TM) Client VM (10.0-b22 mixed mode, sharing windows-x86)
# Problematic frame:
# C [kernel32.dll+0x12aeb]
# If you would like to submit a bug report, please visit:
# http://java.sun.com/webapps/bugreport/crash.jsp
# The crash happened outside the Java Virtual Machine in native code.
# See problematic frame for where to report the bug.
--------------- T H R E A D ---------------
Current thread (0x00395800): JavaThread "main" [_thread_in_native, id=3576, stack(0x003b0000,0x00400000)]
siginfo: ExceptionCode=0xe06d7363, ExceptionInformation=0x19930520 0x003fdf14 0x02de7b04
Registers:
EAX=0x003fde4c, EBX=0x00000000, ECX=0x00000000, EDX=0x02f80600
ESP=0x003fde48, EBP=0x003fde9c, ESI=0x003fdedc, EDI=0x003fdedc
EIP=0x7c812aeb, EFLAGS=0x00000206
Top of Stack: (sp=0x003fde48)
0x003fde48: 02de1de0 e06d7363 00000001 00000000
0x003fde58: 7c812aeb 00000003 19930520 003fdf14
0x003fde68: 02de7b04 02e80087 003fdf14 003fdf28
0x003fde78: 02e99500 00000039 003fde70 00000039
0x003fde88: 003fdec8 02e81a50 02eabf00 003fdf14
0x003fde98: 003fdf28 003fdedc 02dce583 e06d7363
0x003fdea8: 00000001 00000003 003fded0 02a72388
0x003fdeb8: 00000000 e06d7363 00000001 00000000
Instructions: (pc=0x7c812aeb)
0x7c812adb: 8d 7d c4 f3 a5 5f 8d 45 b0 50 ff 15 10 15 80 7c
0x7c812aeb: 5e c9 c2 10 00 85 ff 0f 8e 36 93 ff ff 8b 55 fc
Stack: [0x003b0000,0x00400000], sp=0x003fde48, free space=311k
Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code)
C [kernel32.dll+0x12aeb]
C [summarizer37.dll+0x1e583]
Java frames: (J=compiled Java code, j=interpreted, Vv=VM code)
v ~BufferBlob::Interpreter
v ~BufferBlob::Interpreter
v ~BufferBlob::Interpreter
v ~BufferBlob::StubRoutines (1)
--------------- P R O C E S S ---------------
Java Threads: ( => current thread )
0x02a66000 JavaThread "Low Memory Detector" daemon [_thread_blocked, id=3108, stack(0x02d10000,0x02d60000)]
0x02a58000 JavaThread "CompilerThread0" daemon [_thread_blocked, id=2488, stack(0x02cc0000,0x02d10000)]
0x02a56c00 JavaThread "Attach Listener" daemon [_thread_blocked, id=2508, stack(0x02c70000,0x02cc0000)]
0x02a56000 JavaThread "Signal Dispatcher" daemon [_thread_blocked, id=3720, stack(0x02c20000,0x02c70000)]
0x02a51800 JavaThread "Finalizer" daemon [_thread_blocked, id=2968, stack(0x02bd0000,0x02c20000)]
0x02a4d400 JavaThread "Reference Handler" daemon [_thread_blocked, id=600, stack(0x02b80000,0x02bd0000)]
=>0x00395800 JavaThread "main" [_thread_in_native, id=3576, stack(0x003b0000,0x00400000)]
Other Threads:
0x02a4c000 VMThread [stack: 0x02b30000,0x02b80000] [id=2528]
0x02a67000 WatcherThread [stack: 0x02d60000,0x02db0000] [id=1604]
VM state:not at safepoint (normal execution)
VM Mutex/Monitor currently owned by a thread: None
Heap
def new generation total 960K, used 195K [0x22960000, 0x22a60000, 0x22e40000)
eden space 896K, 21% used [0x22960000, 0x22990c38, 0x22a40000)
from space 64K, 0% used [0x22a40000, 0x22a40000, 0x22a50000)
to space 64K, 0% used [0x22a50000, 0x22a50000, 0x22a60000)
tenured generation total 4096K, used 0K [0x22e40000, 0x23240000, 0x26960000)
the space 4096K, 0% used [0x22e40000, 0x22e40000, 0x22e40200, 0x23240000)
compacting perm gen total 12288K, used 22K [0x26960000, 0x27560000, 0x2a960000)
the space 12288K, 0% used [0x26960000, 0x269658c8, 0x26965a00, 0x27560000)
ro space 8192K, 66% used [0x2a960000, 0x2aeb0e10, 0x2aeb1000, 0x2b160000)
rw space 12288K, 52% used [0x2b160000, 0x2b7b04c8, 0x2b7b0600, 0x2bd60000)
Dynamic libraries:
0x00400000 - 0x00423000      C:\Program Files\Java\jdk1.6.0_06\bin\javaw.exe
0x7c900000 - 0x7c9af000      C:\WINDOWS\system32\ntdll.dll
0x7c800000 - 0x7c8f6000      C:\WINDOWS\system32\kernel32.dll
0x77dd0000 - 0x77e6b000      C:\WINDOWS\system32\ADVAPI32.dll
0x77e70000 - 0x77f02000      C:\WINDOWS\system32\RPCRT4.dll
0x77fe0000 - 0x77ff1000      C:\WINDOWS\system32\Secur32.dll
0x7e410000 - 0x7e4a1000      C:\WINDOWS\system32\USER32.dll
0x77f10000 - 0x77f59000      C:\WINDOWS\system32\GDI32.dll
0x7c340000 - 0x7c396000      C:\Program Files\Java\jdk1.6.0_06\jre\bin\msvcr71.dll
0x6d870000 - 0x6dac0000      C:\Program Files\Java\jdk1.6.0_06\jre\bin\client\jvm.dll
0x76b40000 - 0x76b6d000      C:\WINDOWS\system32\WINMM.dll
0x6d320000 - 0x6d328000      C:\Program Files\Java\jdk1.6.0_06\jre\bin\hpi.dll
0x76bf0000 - 0x76bfb000      C:\WINDOWS\system32\PSAPI.DLL
0x6d820000 - 0x6d82c000      C:\Program Files\Java\jdk1.6.0_06\jre\bin\verify.dll
0x6d3c0000 - 0x6d3df000      C:\Program Files\Java\jdk1.6.0_06\jre\bin\java.dll
0x6d860000 - 0x6d86f000      C:\Program Files\Java\jdk1.6.0_06\jre\bin\zip.dll
0x10000000 - 0x10006000      D:\Servers\SummarizerServer\native\jsummarizer.dll
0x02db0000 - 0x02df2000      D:\Servers\SummarizerServer\native\summarizer37.dll
0x02e00000 - 0x02f6d000      D:\Servers\SummarizerServer\native\platform37.dll
0x4a800000 - 0x4a893000      D:\Servers\SummarizerServer\native\icuuc30.dll
0x4ad00000 - 0x4b52d000      D:\Servers\SummarizerServer\native\icudt30.dll
0x5b860000 - 0x5b8b5000      C:\WINDOWS\system32\NETAPI32.dll
0x77c10000 - 0x77c68000      C:\WINDOWS\system32\msvcrt.dll
VM Arguments:
jvm_args: -Djava.library.path=native
java_command: com.sra.pipeline.servers.summarizer.JSummarizer
Launcher Type: SUN_STANDARD
Environment Variables:
JAVA_HOME=C:\Program Files\Java\jdk1.6.0_06
CLASSPATH=.;C:\Program Files\Java\jre1.6.0_06\lib\ext\QTJava.zip
PATH=D:\Servers\SummarizerServer\native;C:\Program Files\Microsoft Visual Studio 9.0\VC\redist\x86\Microsoft.VC90.CRT
USERNAME=Jim Jones
OS=Windows_NT
PROCESSOR_IDENTIFIER=x86 Family 15 Model 2 Stepping 7, GenuineIntel
--------------- S Y S T E M ---------------
OS: Windows XP Build 2600 Service Pack 3
CPU:total 1 (1 cores per cpu, 1 threads per core) family 15 model 2 stepping 7, cmov, cx8, fxsr, mmx, sse, sse2
Memory: 4k page, physical 1048032k(245796k free), swap 2521804k(1060880k free)
vm_info: Java HotSpot(TM) Client VM (10.0-b22) for windows-x86 JRE (1.6.0_06-b02), built on Mar 25 2008 01:22:05 by "java_re" with MS VC++ 7.1
time: Mon Sep 01 15:22:10 2008
elapsed time: 0 seconds
The dll I'm wrapping is C++ VC++ compiled.
Would like to know what I do to trouble-shoot this error and hope to fix it?
Jim

Using Java print statement was able to show that the my JNI dll was being loaded and that the problem was in the first call to one of my JNI functions. Then by using "DebugBreak()" in that function and gradually moving it down line by line through the function was able to isolate the line causing the problem. Unfortunately it is the line where I call a function from the dll I'm wrapping. See newer thread.

GT-70 2OD Touchpad Problem (disabling button) after updating BIOS and EC

Hi All,
I was solving issues with random BSOD's (https://forum-en.msi.com/index.php?topic=176615.0), but now I got the button that Disables the Touchpad malfunctioning.
I just updated BIOS and EC to 2014-01-17 Versions from MSI website.
The button is not disabling the touchpad and also the LED is not working (well, it used to turn on when the touchpad was disabled), however the "touchpad enabled" picture is showing on the screen everytime the button is pushed.
It's not a major thing, but you know how perfectionists are .... Any idea how to solve this? I'm just going to try updating the touchpad driver with latest from MSI website and let you know the result
Thanks in advance,
PS: Nice community. I just joined this forum and I received a lot of help already!!!!

Quote from: darkhawk on 05-February-14, 01:00:21
Did you perform the EC Reset procedure outlined on the website?
Just to reiterate it:
1. Turn off the laptop.
2. Remove the Battery.
3. Remove the AC adapter.
4. Let the laptop sit there for 20 minutes.
5. Install the Battery.
6. Install the AC adapter.
7. Turn on the laptop.
This might help fix the issue.
Yep, I followed step by step to update the EC.
I just removed original synaptic driver for the touchpad and Installed latest from MSI website. The button doesn't work as before (I was able enable/disable at will), now its behavior is as follows (and I think it was made intelligently):
You can't disable the touchpad if no other pointing device is present
When another pointing device is present, the touchpad disables itself and the button LED is ON (as before). You can't enable the touchpad (before I was able to enable it) if another pointing device is present.
For me, it's OK. BTW... had been about 22 hours without BSOD...
Thank you guys!!!
PS: I just realized that I re-connected my PS3 controller via USB (in the very same USB port that I use to connect it) and the laptop REINSTALLED drivers for it...

The onboard realtek lan choice in BIOS is GONE! after Successful bios flash...

my motherboard is 865pe neo2-v, i have Successfully flashed my bios but now the choice to enable onboard lan has gone from the bios menu??!!! and also all the pci cards i have are not working!!?!!!, any idea what is going on here? windows can not see any pci device i have pluged in the m.b.

Try Clear CMOS Guide and then check your bios settings again.
What version of the bios did you install?

T60p - Black screen after success bios update

Hello!
I have a big problem:
Today I update my T60p bios to the latest, downloaded from the support site, via the windows based factory utility as usual (I do it more than 4 times before). Everything seems OK, but after restart the notebbok won't start. The sysfan is spinning, the leds are lights, but the screen is black, and no reaction for any keypress.
How can I fix this problem?
Thank's for help,
Peter

Hello,
first you could take out your battery and press powerbutton 10 times.
Insert your battery again and try to start.
If your cd drive is running, I would suggest to download bios as an iso-file and burn it to disk.
Then try to boot with this cd and flash bios again.
If these methods don´t work, than you´ll have to send it to service.
Good luck!
Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
Please insert your type, model (not S/N) number and used OS in your posts.
I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
English Community Deutsche Community Comunidad en Español

Still 'Pending Send' after successful inbound and outbound test. CRM Online 2013

I am using CRM Online and Office365. After testing successfully within the admin window for inbound and outbound- emails are still not sending- sitting in Pending Send. Triggers for Email Router is set for inbound and outbound. What
am I missing?

Try the following:
http://www.powerobjects.com/blog/2013/09/19/dynamics-crm-email-router-troubleshooting-101-outgoing-emails/
I always find this page a good place to start to rule out most of the common issues.

Cisco ISE guest portal redirect not working after successful authentiation and URL redirect.

Hi to all,
I am having difficulties with an ISE deployment which I am scratching my head over and can't fathom out why this isn't working.
I have an ISE 3315 doing a captive webportal for my guest users who are on an SSID. The users are successfully redirected by the WLC to the following URL:https://x.x.x.x:8443/guestportal/Login.action?portalname=XXX_Guest_Portal
Now when the user passes through the user authentication splash screen they get redirected to https://x.x.x.x:8443/guestportal/guest/redir.html and recieve the following error:
Error: Resource not found.
Resource: /guestportal/
Does anyone have any ideas why the portal is doing this?
Thanks
Paul

Hello,
As you are not able to get the guest portal, then you need to assure the following things:-
1) Ensure that the two Cisco av-pairs that are configured on the authorization profile should exactly match the example below. (Note: Do not replace the "IP" with the actual Cisco ISE IP address.)
–url-redirect=https://ip:8443/guestportal/gateway?...lue&action=cpp
–url-redirect-acl=ACL-WEBAUTH-REDIRECT (ensure that this ACL is also defined on the access switch)
2) Ensure that the URL redirection portion of the ACL have been applied to the session by entering the show epm session ip command on the switch. (Where the session IP is the IP address that is passed to the client machine by the DHCP server.)
Admission feature : DOT1X
AAA Policies : #ACSACL#-IP-Limitedaccess-4cb2976e
URL Redirect ACL : ACL-WEBAUTH-REDIRECT
URL Redirect :
https://node250.cisco.com:8443/guestportal/gateway?sessionId=0A000A72
0000A45A2444BFC2&action=cpp
3) Ensure that the preposture assessment DACL that is enforced from the Cisco ISE authorization profile contains the following command lines:
remark Allow DHCP
permit udp any eq bootpc any eq bootps
remark Allow DNS
permit udp any any eq domain
remark ping
permit icmp any any
permit tcp any host 80.0.80.2 eq 443 --> This is for URL redirect
permit tcp any host 80.0.80.2 eq www --> Provides access to internet
permit tcp any host 80.0.80.2 eq 8443 --> This is for guest portal
port
permit tcp any host 80.0.80.2 eq 8905 --> This is for posture
communication between NAC agent and ISE (Swiss ports)
permit udp any host 80.0.80.2 eq 8905 --> This is for posture
communication between NAC agent and ISE (Swiss ports)
permit udp any host 80.0.80.2 eq 8906 --> This is for posture
communication between NAC agent and ISE (Swiss ports)
deny ip any any
Note:- Ensure that the above URL Redirect has the proper Cisco ISE FQDN.
4) Ensure that the ACL with the name "ACL-WEBAUTH_REDIRECT" exists on the switch as follows:
ip access-list extended ACL-WEBAUTH-REDIRECT
deny ip any host 80.0.80.2
permit ip any any
5) Ensure that the http and https servers are running on the switch:
ip http server
ip http secure-server
6) Ensure that, if the client machine employs any kind of personal firewall, it is disabled.
7) Ensure that the client machine browser is not configured to use any proxies.
8) Verify connectivity between the client machine and the Cisco ISE IP address.
9) If Cisco ISE is deployed in a distributed environment, make sure that the client machines are aware of the Policy Service ISE node FQDN.
10) Ensure that the Cisco ISE FQDN is resolved and reachable from the client machine.
11) Or you need to do re-image again.

After reinstalling FFox and Adobe Flash Player, why will a certain company webpage will not load, but it does in IE.

For some reason a certain corporate company web site will not load on my desktop PC. The page is gray and white with some headings and a circle in the middle that goes round and round. I previously (some months ago) was able to access the site (and have for years). I am running Windows 7. I have cleared my cache, reinstalled FireFox, reinstalled Adobe Flash Player (even tried downgrading to Flash version 10). If I use IE, the site page loads with all of the graphics, etc. just fine, I have all of the same FF features on my laptop. The site opens up fine on my laptop. What's next?

Is there content loaded on that page via JavaScript or a plugin like Flash?
If the Flash plugin is active the you should get the Flash context menu if you right-click that area.
Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance).
*Do not click the Reset button on the Safe mode start window or otherwise make changes.
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

After Effect CC and Flash Pro CC did not successfully update 19th June '14

After Effects CC and Flash Professional CC did not successfully update, even after several attempts. All other Apps are currently up to date with today's update release. 19th June '14

Hi Rob,
Did you get any error message when you tried to update After Effects CC? Can you share more details?
Thanks,
Jyothi

6 beeps and 6 flashes from LED after graphics card is in and no signal to monitor

I am having problem with my computer booting after installing my gpu. It has worked before with this setup and now its beeping all of a sudden. Sometimes it would boot up fine and most the time it wouldn't boot up at all. So I would leave my pc on sleep and never shut it off. But now it won't boot up with the card at all. I updated my BIOS and unseated the card and ut it back in and nothing. I don't know what else to do. PLEASE HELP!!

Hi: See if following the instructions from the link below gets your video card to work... Normally that happens because legacy mode is disabled and secure boot is enabled in the BIOS. This will only work if your PC has onboard graphics so you can see the display in order to change the settings after you remove the video card. http://support.hp.com/us-en/document/c03653200

Problem after updating Bios. Now the leds only flash and computer rebbots after a few seconds.

Hello.
After upgrading bios on my Elitebook 8440P to ver F20 the computer starts and reboots contiunisly. aprox 5sek for a cycle.

Hello.
After upgrading bios on my Elitebook 8440P to ver F20 the computer starts and reboots contiunisly. aprox 5sek for a cycle.

MSI H81M-E33 BIOS Issues and Post Flash Issues

Hello,
My situation is as follows: (TL:DR at bottom)
Built a new computer and decided to use the new LGA 1150 refreshed CPUs. Bought the MSI H81M-E33 Motherboard and installed windows. Noticed a problem with the rebooting even when installing windows. Thought it was just because of the windows installation, but problem persisted in which the computer seems to shut down but doesn't power down and i have to manually hold power button to power down and then push it again to start up. No real issues it seems since the computer does close processes and shut down but this was irritating me. I read online that BIOS updates seem to fix this problem. Did some research and decided to update with M-Flash to bios v6.6.
As I used M-flash to update to BIOS (selected "Select one file to update BIOS and ME") v6.6 the update stops at 47% and then the computer attempts to restart. BUT it still has the same problem and does not power down. So I manually powered down and started it back up. I then got "no signal" even as I waited. Now I'm freaking out and I power it down again and try again. This time I wait and it get to BIOS (MSI Screen) and then no signal again (not booting windows). Again I hold power down and power back on. Long wait again and I get back to bios. Still freaked out at this point but relieved I didn't brick motherboard.
Decide to flash v6.5 in case 6.6 was too new and might some problems. However v6.5 has the same problems; bios update stops at 47%, computer attempts to reboot, can't reboot, I power off, power on, no signal, power off, power on, wait a while and it gets to BIOS (MSI Screen), then boots to windows.
Right now the bios does read the bios version as v6.5 but I still have the issues in restarting where that doesn't really work. In addition, I now have this wait from pushing the power button to when I see BIOS (MSI Screen).
TL:DR
Had reboot problems decided to update BIOS
Used M-flash ("Select one file to update BIOS and ME") to update to v6.6
Update stopped at 47%, computer attempted to reboot, got no signal (reboot problem), powered off, powered on, waited a long time nothing, freaked out, powered off, powered on, waited a while got to bios (Whew), checked for new version (it is).
Decided v6.6 might be too new decided to try v6.5 used M-Flash again
Again stopped at 47%, computer attempted to reboot, got no signal (reboot problem), powered off, powered on, waited a long time, nothing, powered off powered on, waited a while got to bios, checked bios for new version (it is), save and exit, no signal, power off, power on, waited a while got to bios, then booted into windows
My concerns are;
I seem to still have reboot issue.
I have to wait for BIOS now, no longer pretty quick start.
My questions are;
Did I mess up the flashing somewhere?
Was stopping at 47% normal?
Should I try to update the BIOS another method to fix my current problems?
Am I missing a step somewhere?
Any help is appreciated, I just got really freaked out by the whole process but I'm just glad the computer still works (kinda).
Thanks in advance for any help, and apologies on the long essay just wanted to be as specific as possible.
-J
Specs:
MSI H81M-E33
Intel i5-4590
Corsair CX-430
Crucial Ballistix Sport 8GB
PNY Optima Series 240GB
Seagate Barracuda 1TB
LG 12x BD-Rom
Microsoft Wireless Desktop 2000

MFlash reboots in the process. To be sure reupdate using the below instructions and archive for a proper fpt flash. If you used Win8 feature (fastboot) before the first update be aware taht you need to set anything again after an update (e.g. enabling safeboot) as everything is set to default.
>>Use the MSI HQ Forum USB flasher<<
A.) Download the attached archive (E7817IMS_660.rar.rar) and place it on your desktop. Do not decompress.
B.) Download and install the Forum flash tool.
C.) Insert your FAT32 formatted usb stick.
D.) Make sure that all win 8 options are disabled. (Fast Boot etc) Also make sure the legacy USB is enabled.
E.) Start the forum flash tool and select option 1. Then point the tool at the compressed archive we downloaded earlier. Then to your USB Flash Drive.
F.) Boot to the USB
G.) Now follow the directions and let the tool flash
H.) After flashing reinstall ME drivers in Windows: http://download.msi.com/dvr_exe/intel_amt90_mb.zip

MSI 770T-C45 won't post after flashing BIOS with M-FLASH

After flashing AMIBIOS 8.3 to v8.7 with M-FLASH via USB stick I can't get any post.
Had I read this forum before I wouldn't have done it, but here I am.
Fan starts, LEDs are off, no beeps at all, power button does nothing. Black screen.
After force flashing (yes, I am THAT stupid) the prompt said it would reboot in 5 seconds and after that nothing.
Here's my setup:
Board: MSI 770T-C45
Original Bios: v8.3
Flashed Bios: v8.7 (flashed with M-FLASH)
VGA: EVGA NVIDIA GeForce GTX 660
PSU: Enermax FMAII EG465AX-VE 460W
CPU: AMD Phenom x4 9650
MEM: Kingston DDR2-667 4x2GB KVR667D2N5/2G
HDD: SAMSUNG 840 SSD 250GB
OS: Windows 8 Pro 64bit
I tried every CMOS clearing method found in previous posts and threads (including this and this.)
1. Unplugged from power, waited 5 minutes, removed the battery (5mins), changed jumper position (5min), switched it back (5min), plugged it in (5min) and powered up with and without USB stick in the hub next to network hub with old BIOS (v8.3) inside. Pressed CTRL+HOME, anything, not a single message or beep or LED flashing.
Also I removed all RAMs and kept one in the first socket. Nothing.
I really don't know what to do next. What seems to differ from other users is LEDs non working, what does that mean?

The problem here is that after update 8.6 the m-flash module was updated, so yes your mobo is a brick, but there is still hope for it. I had the same situation a few days ago with the exact same model and was able to recover it by following the steps on listed on the below posts:
https://forum-en.msi.com/index.php?topic=133578.0
https://forum-en.msi.com/index.php?topic=129989.0
It may seem complicated at first, but trust me its not at all.
Anyways you probably already have another mobo, send it for RMA or used it as frisbee, but it may come handy for some other doing the same noob flashing as we did

Previous image flashes on the screen occasionally when opening safari. Even after clearing history and cache.

Occasionally an image from a previous website appears briefly when opening safari. I'm afraid it might do it with a site that has private information and other individuals use this ipad. Is this a problem fixed in the updates to the iOS or something different entirely. The image flashes sometimes even after clearing history and cache.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

BFG 7800GS OC and MSI 6702E problem, no video signal after post

Okay this problem has me stumped and the techs at BFG are thinking there is a conflict problem with my mobo and this card.
Heres the case:
I got 1 - BFG 7800GS/OC and I installed it in my MSI 6702E (K8T Neo2 F/FIR). The system runs its POST fine and it gets to the OS selection screen. Right after that (where it should load windows) the screen goes black and the screen acts like its looking for a signal on its digital or analog feeds (a small window appears on my screen indicating signal on which port and for me its on the digital).
This is what I've tried so far:
1) I unistalled NVIDA drivers
2) Tried booting to safe mode
3) I bought an Antec SmartPower 2.0 PSU 500W (see http://www.antec.com/us/productDetails.php?ProdID=26500 for specs)
4) repeated steps 1 and 2 with new PSU
5) Updated to 9.3 BIOS
6) Confirmed VIA drivers version is latest (5.10a)
7) Got another BFG7800GS OC and repeated steps 1 and 2
8) Bought another PSU its a BFG 650W (see http://www.bfgtech.com/power_supply_650W.html for specs)
9) repeated steps 1 and 2 with 1st and 2nd 7800GS
I have tested the cards in another AGP system and the cards work perfectly. I've talked to the BFG tech support and they feel their could be a conflict with the mobo, but I'm at a loss to find any info on that in these foums.
Note that both PSUs have 12v rails that are rated combined >20 Amps
My system Specs:
Athalong 64 3200+
K8T Neo2 F/FIR
2 - 512 MB Kingston DDR 400
2 - 256 MB DDR 400
1 - Seagate 200GB HDD
1 - WD 80 GB HDD
1 - TDK DVD +/- RW
SB Audigy 2 ZS Gamer
PNY 6800 - soft modded to GT with extra Vertex Shader enbled

I can't boot into safe mode, normal mode, vga mode. The computer only POSTs and then gives me the OS selection, which I then choose and thats it.... black screen. No sound, no video then eventually my screen goes into power saving mode. I don't even get the windows logo screen.
My previous system worked great minus the declineing game performances. I'm simply replacing the softmodded PNY 6800 to this new BFG 7800 GS. I know the video card working is not the issue since I had it working perfectly in another PC. So no this is not a new build.
Yeah so the deal on those 2- 256 MB DDR 400 ram sticks is that there is no visable brand name. There is a sticker on it indicating its stats and a little logo of some company I don't recognize. The RAM sticks themselves have a silver colored heat spreader, but I don't think that has anything to do with the situation. The RAM in this computer is top notch and its been stable for over a year.
I'm really at a loss here on what the problem might be, but I have to imagine there is some issue going on with the AGP bus. I've tried messing with the BIOS settings and setting fast writes to off, AGP to 4x, aperature to 256 mb then back down to 32 mb. All those settings result in the same symptoms.
Man this is really perplexing since it seems others have this same board wih this card running fine. Since I can't seem to find anyone with a similar issue.

No signal after successful Bios and ME flash

Similar Messages

Maybe you are looking for