No signal even if the computer says i am connected to the network wirelessly,
I HAVE A HP PAVILION MEDIA CENTER a1547c DESKTOP PC ,I HAVE CONFIGURED IT TO CONNECT TO A WIRELESS NETWORK AND IT SAYS I AM NOW CONNECTED BUT IT ALSO SAYS NO SIGNAL, WHAT IS THE PROBLEM?IT HAS A BELKIN G WIRELESS ADAPTER...EMAIL ME AT [Personal Information Removed] thanks ,it has WINDOWS XP MEDIA CENTER EDITION SERVICE PACK 2 OS.THE BELKIN WIRELESS G DESKTOP CARD #2 IS FLASHING THE GREEN LIGHT LIKE A DISCO LIGHT WHEN I TURN ON THE COMPUTER..i have diagnosed the connection, it says failure in IP,GATEWAY, DNS..WHAT IS THE SOLUTION?
My computer says I am connected to wifi, but when I go to use the Internet, I am not connected.
Usually when this occurs on one Wifi and Internet connection, the wifi router is working, but the router connection to the Internet Service Provider is broken. Resetting the modem or router/modem combination often results in a new connection to the ISP being established (baring any data caps limits, line, modem or ISP troubles)
However your mentioning it's not connecting anywhere your going on wifi or Internet, which could mean your machine has been compromised and possibly blacklisted until it's cleaned up of malware, or you tried to self solve your earlier issues and messed up your Network settings.
I tend to lesser think it's a actual hardware problem, but it might come to that eventually.
You should test the compromised/blacklist theroy by using a Ethernet cable to the modem you know has a good Internet on and powering on/off the modem. (if a router/modem combination, then no need). If you get Internet and not kicked off in a few minutes, then your machine is fine, likely messed up Network settings are too blame.
You can clear everything out by creating a New Location by editing locations and creating a new one, also by going to Airport Advanced > Airport and deleting all the previous connections to start over new. Reboot.
Connect manually to your home network and save in Keychain when it asks.
If this is all too much for you, take it to a local PC/Mac repair shop as they specialize in software/network issues.
Similar Messages
-
I was having issues with firefox so I upgraded to firefox 4. I am connected to the internet but when I open firefox or even internet explorer it says Unable to connect problem loading page. Nothing will pull up!!!
I don't know if you are still having the issue but if you are have you contacted your ISP? It sounds to me like it's more of a connectivity issue than a browser problem. I've dealt with similar things several times and in both cases it was something with the modem or an ISP setting.
I'm also wondering if it could be a Wi-Fi issue. Can you log in to your router? (It varies by brand but you would go to a site such as http://192.168.10.1. That is for Trendnet. The information for yours should be in the documentation that came with it.)
You should be able to get the router log in page to come up even if you can't connect to any websites. (Provided the network is set up correctly.)
I also would double check your connection settings (if you're connecting over Wi-Fi) or your ethernet connection. (If you're connected directly to the modem and router.)
Hopefully one of these suggestions will be helpful. -
I have tried to reset my wifi and use different wifi systems. I am in college, so I have tried to use the internet both on campus and in my home in Dallas, neither of which worked. I JUST WANT TO HAVE INTERNET.
My computer says I am connected to wifi, but when I go to use the Internet, I am not connected.
Usually when this occurs on one Wifi and Internet connection, the wifi router is working, but the router connection to the Internet Service Provider is broken. Resetting the modem or router/modem combination often results in a new connection to the ISP being established (baring any data caps limits, line, modem or ISP troubles)
However your mentioning it's not connecting anywhere your going on wifi or Internet, which could mean your machine has been compromised and possibly blacklisted until it's cleaned up of malware, or you tried to self solve your earlier issues and messed up your Network settings.
I tend to lesser think it's a actual hardware problem, but it might come to that eventually.
You should test the compromised/blacklist theroy by using a Ethernet cable to the modem you know has a good Internet on and powering on/off the modem. (if a router/modem combination, then no need). If you get Internet and not kicked off in a few minutes, then your machine is fine, likely messed up Network settings are too blame.
You can clear everything out by creating a New Location by editing locations and creating a new one, also by going to Airport Advanced > Airport and deleting all the previous connections to start over new. Reboot.
Connect manually to your home network and save in Keychain when it asks.
If this is all too much for you, take it to a local PC/Mac repair shop as they specialize in software/network issues. -
My computer says it's connected to the internet, but I keep getting a message that my computer can't find the server. Could there be a problem with my computer's internet connection?
First, unplug the modem, for at least 10 secs., then unlpug you airport/ wifi/ then try to reconnect.
If it it does not not work, reconnect your modem, then reconnect your network utilites, use assistance. -
My computer says it is connected to internet but it does not load the webpage
my computer says it is connected to the internet, full bars but it does not load the webpage when i click on safari
If you are connected wirelessly it is possible to have full bars, but your wireless router connection to the Internet could be the problem. Try restart your router.
-
my ipad2 is unable to find wireless network(s). while at home I am able to connect my MacBook and iPhone to network but am unable to connect iPad. I have restarted the device multiple times and even reset the network and all settings but still no luck
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
My ipod keeps searching for network, even when the network info is all set properly. It has suddenly started doing this. Also, buffering forever... I have tried to reset the network few times, but not working.
Hello Nazer_502,
I would be concerned too if my iPhone was acting this way. It sounds like it is overheating and not holding a charge. I recommend following the steps listed below when experiencing an issue like this:
Battery life seems short
Click ( www.apple.com/batteries/iphone.html) for tips on how to prolong iPhone's battery life.
Try turning iPhone off and then on again.
Connect iPhone to iTunes and restore iPhone.
If the screen shows a low-battery image, the battery is low on power and needs to charge for up to ten minutes before you can use it.
When charging iPhone, make sure to leave it charging until it is fully charged. You'll know the battery is fully charged when the battery icon in the upper-right corner of the screen looks like this .
Note: When charging using a computer, don't connect iPhone to a keyboard. Also, the computer must be turned on and not in sleep or standby mode. If iPhone is connected to a computer that's not turned on or is in sleep or standby mode, the iPhone battery may drain.
You can find the full article here:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Thank you for using Apple Support Communities.
Best,
Sheila M. -
my ipod touch 2nd generation wont connect to itunes. my computer says it is connected, but has no drivers. what does this mean and how do i fix it?
Start here. See the driver topic first.
iOS: Device not recognized in iTunes for Windows -
Why isnt my itouch not connecting to the wifi? everytime I try to connect to a network and i put in the password it says "unable to connect to this network" why isnt working?! the password is correct and everything. I just dont understand why its not working. Someone please help me! thanks
Did it ever work with this WiFi system?
Do other devices work with this WiFi system? -
hi..
i've got problem with my iphone 4s gsm factory unlocked it won't connect to a wifi. i tried to hold the power and home button even reset the network setting but ended with i am not even can turn the wifi on. does any body can helpme?See this: http://support.apple.com/kb/TS1559
If you carefully follow all of the instructions in this tip and none of them restore WiFi then your radio chip has failed and you need to get the phone replaced by Apple. -
Can you not sync wirelessly with a desktop PC on a wired network, while your iPhone is on the network wirelessly??
I also thought that this was the case, but that is incorrect. Please see my previous post below:
I was having the same problem with an iPhone 4 and Windows XP. I finally fixed the issue! I read several posts over the past month telling me to make sure that both the PC and iPhone were on the same network. I thought that both were on the same network; however, I was using my "Guest network" to connect my iPhone to my Airport Base Station. In order for both devices to be on the same network, the first 3 numbers of both IP addresses must match. For example, if the PC's IP address is 199.167.1.X, the iPhone's IP address must be 199.167.1.Y. I signed onto my password-protected network from the phone just to see what IP address it would use. As soon as I logged on, my iPhone started to sync wirelessly. I don't know if this will work for anyone else, but I would suggest comparing the IP addresses of your PC and iPhone before doing anything else. For those posting that the PC and iPhone must be on the same Wireless network, my PC is hard-wired to the Airport Extreme and it still works!
My Setup:
iPhone 4 (running IOS 5.0.1)
Dell PC (running Windows XP SP3) (no wireless network card)
Airport Exteme Base Station (5th Generation & updated firmware) -
Shut down computer now won't connect to my network
the computer has been connected to my wireless network for a few days, then last night i shut down the computer and when i started it back up this morning, it could not connect to my network and gave me an error saying "There was an error joining the airport network "__"." (where __ is the name of my network) Other computers in the house are working just fine, what can i do to fix this? (i've tried restarting and shutting it down again and that didn't work)
the computer has been connected to my wireless network for a few days, then last night i shut down the computer and when i started it back up this morning, it could not connect to my network and gave me an error saying "There was an error joining the airport network "__"." (where __ is the name of my network) Other computers in the house are working just fine, what can i do to fix this? (i've tried restarting and shutting it down again and that didn't work)
-
Epson Artisan 800 can't scan over the network (wireless)
Hi,
I installed the Artisan 800 all-in-one drivers and software. I can print wirelessly. I looked up Epson scanning setup help. When I open Epson Scan Settings.app, click on "Network", but all the buttons are disbled (unclickable). Therefore, I cannot click "Add" and all the subsequent steps. I tried adding the app to the "incoming allowed" list in Firewall, disabled the Firewall entirely, but to no avail. Funny thing is, it was working a couple of months ago when I had the printer new, but since then I have installed a couple of OS X updates (I believe I had 10.5.5 when it was working). In the intervening period, I also messed around with the OS X supplied Printer drivers (deleted a whole bunch of files, not sure if some required files were deleted), and I noted that the recent 10.5.7 update (and possibly 10.5.6 before) did not restore those files. However today I uninstalled all the Epson drivers/files using the A800 supplied CD, and reinstalled everything. I even tried installing the scanner files from Epson's webpage. Nothing worked. Please suggest something!i had a similar problem -I connected by printer to an iMac via a network cable to a Time Machine 802.111 router. Could print but not scan. I could only get the scan functions working by setting up the wireless connection on the printer. But then I could not print until i reconnected the network cable between the printer and the TIme capsule. Tel support from Epson seemed more confused than me!
Should I have to have the printer networked by cable as well as wireless? That seems silly. I must be missing a step in one of the setups. -
Ok. I have a new macbookpro which I love. However, we can't get it to print. We just got Comcast with a modem and wireless router. We can all get into the net wirelessly (4 of us). My son set our PC to share the printer, gave it a name and got his PC to work through it. Mine kept pausing (it's been a week now). Finally connected directly to the printer and it immediately went out and found the drivers (for all HP photosmart series) and installed them (I think they are installed. At least they are listed under drivers in the print/fax section). We then did a test print with it hooked up and it worked. Back to wireless and it keeps pausing or telling me it can no longer communicate with the printer. Tried going back and printing while connected to the cable and it didn't work. Several pages of one liners with gibberish on it (some words like fax, document it) but then it failed. I did tell it the wrong model of printer the other day and there is a picture of it under the real printer (which is listed by the name we gave it on my pc). But I know have the correct driver and it shows it in the bar under the driver listing. The other picture of the wrong model is not highlighted and I don't know how to delete it). It just keeps pausing and telling me I'm no longer connected to the printer. BTW, It tells me the printer is ready and shows the name prior to trying to print. We've tried everything including many suggestions from others. Any suggestions? I find it strange I was able to print yesterday while connected directly and tonight it failed (otherwise the printer is working for others). THANKS SO MUCH! Frustrating to say the least but I'm NOT giving up. Carol
I should add that it's an HP photosmart 4280.I found it online and it shows the Mac 0SX operating system.
-
Successful internet connection, but keeps saying im not connected to a network
I have printed out the Wireless Network Test Results and its says no problems found , successful setup, but when I try to use the efax or any other apps on the printer it keeps telling me "No connection , your printer is not connected to a network" , Please help , and also not sure if pc is 32 or 64 bit.
Hey , Welcome to the HP Support Forum. I see that you're unable to use eFax with your HP Photosmart 7515 e-All-in-One Printer. I would like to help. I have located an article from HP might restore this feature for you. Click here and work through Solutions Two through Three. If you'd like more direct assistance you can call our Cloud Services at 855-785-2777. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html Let me know if this works out for you. If I have helped you resolve the issue, feel free to give me a virtual high-five by clicking the 'Thumbs Up' icon below and clicking to accept this solution. Thank you for posting in the HP Support Forum. Have a great day!
Maybe you are looking for
-
as i write this i have just restored my gf's computer back to default factory setings and cleaned the HD she has a horrible habbit of downloading anything and everything something tells her to download it her most recent actions caused her to dl a vi
-
Another thing that happened recently is someone tried to reset the password of my Apple ID. Since i have erased my phone, will the thief be still able to use the phone? If i remove my phone from my Apple account will he be able to use it then? Note:
-
Search and replace a clickbox for a transparent button?
Is it possible to replace all click boxes for transparent buttons in a project? Why? Because you can style a transparent button. You cannot style (as far as i know) a clickbox. Ton.
-
Itunes reports file could not be found
Whenever I try to synch my iPod, iTunes does two things: 1. It reports several "file not found" errors; the filenames look like they were possibly pictures (and maybe this is connected to #2, below) 2. It reports that Drive H: is unavailable...whic
-
Hello, I have a question about List of values. I have a bex query which has a variable on selection screen so when i try to build a webi report on top of it and try to preview it, it doesn't auto populate the list of values in the box. is it supposed