Nomad model# DAPAGO1 "Could not detect HDD" error

;Hello,
I see that other people have posted this question but I haven't found any answers. Apparently there was an article about this error on a site called nomadness.com, but that site is now gone. However, the fact that there was an article about it leads me to believe that there may be a solution.
Any help?
The error message I get when I turn it on is:
Critical Error
Could not detect HDD
Shutting down
Thanks

Poking around a little more I see some suggestions about this error being caused when the batteries are too low. I was actually trying to use it plugged in but without batteries. I had put it away and so I took the batteries out. If these batteries don't work can I use regular alkaline batteries? If the HDD is actually bad (I found out that the article that used to be on nomadness.com was about how to replace the HDD) I'm just going to chuck it, but I'd like to see if it can be solved by charging or replacing the batteries.
Thanks

Similar Messages

Jukebox 20 gig has "critical error" could not detect HDD shutting d

I just powered the 20 gig up, and the critical error message apeared. Is there anything I can do?

Poking around a little more I see some suggestions about this error being caused when the batteries are too low. I was actually trying to use it plugged in but without batteries. I had put it away and so I took the batteries out. If these batteries don't work can I use regular alkaline batteries? If the HDD is actually bad (I found out that the article that used to be on nomadness.com was about how to replace the HDD) I'm just going to chuck it, but I'd like to see if it can be solved by charging or replacing the batteries.
Thanks

Model entry point 'test uuts' could not be executed error -18002

Hi,
I am running a testand(2.0.1f1) sequence of labview (7.0) steps and it is working perferctly in my computer , but when installing testand and labview in another computer and I try to run my sequence the next message appears. "model entry point 'test uuts' could not be executed error -18002"
Is anyone that has an idea of what is happening here?
Thanks =)
Eren

Hi Eren,
You might try mass compiling the TestStand folders so that all VI's are at the same Version. TestStand 2.0.1f1 installs VI's that are at ver5.1.1
When you run from the Entry Point eg "Test UUTs", before the sequence executions all VI's in all the sequence contained in the sequence file are loaded in to memory.
Look at the error message again, it should be telling you which step in which sequence of the sequence file is not executable.
Hope this helps
Ray Farmer
Regards
Ray Farmer

When trying to deliver an iBook with videos I receive this error message: 'ERROR ITMS-9000: "Book contains unsupported video my book title.iBooks.OPS/assets.media/my video name.m4v. Could not detect ftyp' at Book (MZItmspBookPackage) Any suggestions?

When I try to deliver an iBook to the iBookstore I receive the folllowing error message. ERROR ITMS-9000: "Book contains unsupported video my book title_.ibooks:/OPS/assets/media/My video title.m4v. Could not detect ftyp." at Book (MZItmspBookPackage)
I have no idea what this means and would be grateful for any help.

KT,
Thank you so much for your interest and response. I think that I followed all the suggested 6 steps from the iBA user tip but to no avail. Do you know anything about this comment by dmingo which is pasted below?
'User dmingo says this about that:
After audio tracks are placed in your book, you must 'Publish' the book from iBA (using the 'File/Publish...' menu) - that means re-entering all metadata from scratch - you can't simply import the .ibooks file into iTP. If you enter another audio clip at some time, you have to do it all again. '
To me it seems to say the video clips need to be delivered separately and one at a time.
I would be grateful for any advice

Could not commit transaction Error 1 Detected During Transaction G/L Account

hi experts
when i was adding Sales Order i am getting an error as Could not commit transaction Error 1 Detected During Transaction G/L Account

Hi,
Plz find the following threads:
Transaction failure with error message \"Error -1 detected during transaction\" when update the G\\L Account D…
"Could not commit transaction: Error -1 detected during transaction"
Could not commit transaction: Error -1 detected during transaction 'Payment Methods for Payment Wizard' (OPYM)
Could not commit transaction when inserting new items

"Could not commit transaction: Error -1 detected during transaction"

hi guys,
im getting this error "Could not commit transaction: Error -1 detected during transaction" when trying to create standard document/s. i am now using B1 8.8, MS SQL 2008.
originally, my program was written for B1 2005, MS SQL 2005, and it WORKED.
we upgraded into B1 8.8, MS SQL 2008, and now my program is not working. it is now having the mentioned error upon committing transaction (vCompany.EndTransaction(wf_Commit)). tried removing transaction handling, and it WORKED. also, tried simplifying the program, instead of creating multiple documents, i modified it in just creating one document with transaction handling, and it WORKED.
initialliy, this issue seems to be related to MS SQL 2008.
please help, thanks.

Hi Emmanuel........
You get this error due to the Approval Procedure.
Please check if it is activated then please deactivate it from Administration> Approval> Approval Template.......
Then try.......
Regards,
Rahul

I tried to restored my iPad1's iOS5 to factory setting. There are error messages. Now my iTunes could not detect my iPad anymore. How can I proceed from here?

Hi All,
I have problems with iOS5 installed on my iPad1.
After successfully installing the new iOS5, my iPad1 apps are jumbled up with my wife's apps. Some of my paid apps are missing.
So, i tried to restore to factory default. Now, my iTunes could not detect my iPad, and my iPad only shows the picture "to connect iPad to iTunes".
I restarted my iMac and checked that all softwares are up to date.
Please advise.
Many thanks.

If you restored from a backup, you simply restored the corrupt files again.
You could find the corrupt file through a slow process of eliminating apps and data - removing all content - and then syncing content back again - slowly adding apps back on - until the problem surfaces again - and the you could pin down the last apps or apps that you just added as being the problem apps/files. You may find the corrupt file - and you may not.
Your backups can be deleted by going to iTunes on you computer and go to Edit>Preferences>Devices. You will see your backups/backups in that window. Click on the backup and then click on delete backup - if that is what you really want to do.

IMac 24" could not detect external monitor (early 2009 model)?

I am trying to add a second monitor to my iMac through the mini Display port with a mini-Display to VGA convert cable, somehow my iMac could not detect the second monitor at all on the preference-display menu. After connected the cable and an external monitor I restarted iMac a few times, the external monitor still could not be detected.
Any suggestions? Any simple method to test if the mini Display port is working properly? My iMac OSX 10.8.5
Thanks
David

Hi,
Just tried another miniDisplay - VGA cable, it works! No need to restart iMac. Immeditely I can bring display windows to the second monitor, say, a DVD movie play to the second monitor while working on the main iMac monitor for other tasks.
David

Setup could not detect any Sound Blaster Audigy card on your system

Hi from Barcelona!
I've a Soun Blaster Audigy card (Model: SB0090)
I tried to install the Audigy software and drivers from the original product CD but Setup was unable to find Augigy hardware and halted the installation!
"Setup could not detect any Sound Blaster card on your system. Please ensure that your Sound Blaster hardware is properly installed before running this Setup program"
By the way. Manually the sound drivers can be installed working only front speakers of the 5. Creative system
I tried a clean installation of Windows XP and Windows 2000 PRO (reformatted the hard dri've) but Audigy install CD still could not find Audigy hardware.
I've changed the card to a different PCI slot with the same results!!! Damaged?
What is happening? I need a solution!! Many users have this problem to with other Sound Blaster cards and models...

ADSLNEW wrote:
It seems to be an important BUG of Creative Sound Blaster Audigy cards related with EEPROM!!!
Yes, indeed, that is my theory as well. After much ****hing and on-line research, it seems that this problem has been around since 2002. From Creative Labs point of view, it appears they view this as "pilot error" -- the user has installed the card in a system that is not fully compliant with the latest standards -- specifically Microsofts ACPI (configuration and power management). A wide variety of configurations and/or actions seem to cause the PCI subsystem ID in the Audigy EEPROM to be erroneously overwritten -- including certain older motherboards, certain older PCI cards, and perhaps other actions.
Once the subsystem ID in the EEPROM is overwritten and has garbage information, many or all of the Creative applications cease working and various sound problems can arise. Attempts to reinstall the driver or update to the latest driver consistently fail becuase of the dreaded "Setup could not detect any Sound Blaster Audigy card in your system..." error message.
There appear to be four fixes:
) Get a replacement Audigy card from Creative, but <EM>only</EM> after you perform their prescribed troubleshooting steps to prove that the card is indeed the source of the problem. Apparently, the steps include installing the card in another PC. Apparently, Creative in Europe is more willing to replace your card than Creative in the US. It's up to Creative Labs whether or not they issue you an RMA ("Return Material Authorization").
However, this fix will fail if the root causes of the EEPROM error are not corrected. Apparently, Creative Tech Support isn't always a foolproof source of guidance, so the burden is on you. The root cause MUST be corrected before the new card is installed, or the same problem will happen all over again. Eliminating the root cause may involve replacing your motherboard, replacing other PCI cards, or manual configuration (disabling ACPI).
2) Reprogramming the EEPROM. This is for advanced PC owners only, because it involves desoldering the EEPROM, programming it, and resoldering (and even lifting some pins to prevent reprogramming). There are instructions on how to do this posted in the German Creative Labs discussion board, by a Russian (!). I have links for those who are interested.
3) Removing the Creative drivers and software (using Clean Sweep procedures and third party utilities), updating again using Windows XP SP2, then physically moving the card to different PCI slots (multiple times if necessary), until ACPI Bios writes the proper information into the EEPROM. You can then reload the drivers.
Again, the root causes of the problem must be removed or your fix will only be temporary (a day or two). This solution also seems to be very dependent on the specifics of your system (motherboard, PCI cards, etc.).
4) Some people have had success in by-passing the step in the driver installation process where they check for the Audigy card subsystem ID, using a utility called CTZAPxx on the installation CD. Then then manually install each of the applications they need to use.
5) Use the open source driver from the kX Project (http://kxproject.lugosoft.com/index.php). This driver (and associated utilities) does not depend on the detailed configuration of the card (i.e. they don't check subsystem ID) and appear to work fine even with cards with corrupted EEPROM.
This driver is aimed primarily at computer music applications, and opens up the on-card signal processing capabilities. The downside is that the Audigy 2 ZS does not have all of it's capabilities supported <EM>yet </EM>(e.g. Dolby Digital decoding, S/PIF passthrough, possibly some game sound features, THX, 24-bit recording, support for Hyperthreading CPUs, etc.). But scanning over the discussion boards, the user community seems to be MUCH happier with the performance and support associated with these drivers than with Creative's.
This is the direction I'm going. I'm not a big gamer and I don't really care about the latest in home theater audio performance. Basic 5. surround sound is all I care about, and I'm much more interested in computer music capabilities.
I have also lost faith in Creative Labs as a vendor to provide the support I want and need going forward. Just imagine if the Creative Labs were running the Space Shuttle program :smileysurprised:.

Could not detect Sound Blaster Audio Card on xp sp2 Sys

I have Audigy Platinum and trying to install to a recently re-installed windows xp sp2 system. On my previous install everything was working fine and now I am looking to install the newest drivers and the error comes up [color="#ff3300">"could not detect Sound Blaster Audio Card on system". The strange thing is windows recognizes the card and will install it's drivers, but when I go to install the latest driver update I get the error. In addition, I also tried to run the install from my original disk.
I also?un-installed the devices showing? in the windows device manager, then tried and the same error, I even tried it in safe mode. Any ideas?Thanks and Advance,Mikel

Yes i think the real lesson here is not to buy creative,. i have the same problem with their junky card, so i guess ill just have to take buisness somewhere else. if you all do the same perhaps the threat of them going out of buisness will have them deal with their problems. if not atleast we saved others the headache of learning this lesson.

::"setup could not detect any sound blaster audigy on your system

Hej!
Har ominstallerat WinXP PRO och tappade bort ljudet helt! Datorn kan se ( via Windows update) att det ?ren ljudenhet installerad men kan inte hitta drivrutiner, gick d?refter in p? er sida och provade f?rst med manuell nedladdning men d? kommer ett felmed upp som lyderkonstigt t?nkte jag..Provade erat eget autodetect program men d?r hittade programmet r?tt!!
Produkter i ditt system:
Sound Blaster Audigy 2 ZS
Laddade ner och k?rde programmet och d? f?r jag medd IGEN!!....
Allts?:
Era program hittar mitt kort f?r att sedan INTE hitta mitt kort...
HJ?LP

mrbergman wrote:
Hej!
Har ominstallerat WinXP PRO och tappade bort ljudet helt! Datorn kan se ( via Windows update) att det ?ren ljudenhet installerad men kan inte hitta drivrutiner, gick d?refter in p? er sida och provade f?rst med manuell nedladdning men d? kommer ett felmed upp som lyder:"setup could not detect any sound blaster audigy on your system"..konstigt t?nkte jag..Provade erat eget autodetect program men d?r hittade programmet r?tt!!
Produkter i ditt system:
Sound Blaster Audigy 2 ZS
Laddade ner och k?rde programmet och d? f?r jag medd::"setup could not detect any sound blaster audigy on your system".. IGEN!!....
Allts?:
Era program hittar mitt kort f?r att sedan INTE hitta mitt kort...
HJ?LP
Hejssan
I think you understand english good enough (som ni alla svenskar brukar g?ra (b?ttre ?n vi finskar i alla fall)) so I just give a link to another thread on this forum.
This issue you're having, is quite common for Creative Audigy carrds (perhaps with OEM models mostly) if you just search this forum.
You can use those instructions to get some drivers installed to your card. Install drivers first and then all the Creative software you need.
You need WinRar being installed into your system to get driver package extracted. You can download it from http://www.winrar.de/edownload/winrar.html
Here is the link
.jtp

Setup could not detect any Sound Blaster Audigy 2 on your Sys

Here's the deal. I have used my Soundblaster Audigy 2 Platinum without incedent for a long time with the following box:
Asus A7V333
XP 800
.5 GB DDR 2700
I changed cases, but all of the components remained the same. Everything else went like clockwork, but no Audigy.
So I did a clean and replace of the drivers, however, I had no Audigy CD. I ordered the CD from Creative, but it looks to be a CD for the Audigy 2 XS...will this work for the Audigy 2 Platinum?
So when I go to run the CD, I get the following error:
Setup could not detect any Sound Blaster Audigy on your system.
Please ensure that your Sound Blaster Hardware is properly installed before running this Setup program
Setup will now exit.
I didn't change slots and the IRQ is still the same.
I can provide any additional documentation, i.e. screen shots of device manager, et al. to anyone interested in helping.
Also, if you li've in Chicago, I will get you drunk.
I am so irritated with this thing... I remember it being a pain in the @$$ to install the first time, but not like this.
Cheers,
-rob

Okay I ended up fixing this problem myself seeing as a lot of these forum topics just come to a dead end with no real resolution.
Let's get 'Creative' ...
I removed the reg entry hkey_local_machine/software/creative tech, removed all drivers, programs, and anything that even smelt faintly of creative.
Just to make sure I ran the CTZAPXX.exe on the cd and removed drivers again there also.
Then upon a swift reboot I used CTZAPXX.exe to install the drivers, ran the cd, unchecking the option at the bottom of the 'custom' install list to install windows drivers (as it had already been done)
Now I'm back in business
Though, all through the ages I've never had a creative soundcard, which hasn't given me trouble at some stage, man I even have shameful memories of my AWE64... Lift your game creative, you've got a great product line, just a pity the shoddy drivers sometimes let them down.
This post may be a little outdated, but it's really intended for all you googlers out there I really hope this fixes your problem!

"Adobe Captivate could not detect a recording device ..."

Adobe Captivate shows my Snowflake USB microphone but doesn't record sound from it. When I choose Calibrate I get "Adobe Captivate could not detect a recording device". However, I can record from the microphone in all my other apps (Rosetta Stone, Sony SoundForge, etc.), so I know it's not a hardware issue.
When I go to "Sound" in Vista Pro's "Sound" option on control panel the Microphone is chosen as the default recording device, and I see the bars moving up and down when I talk.
What can I do to get "Captivate" to see the Mic?
A temporary workaround I found is to plug the Microphone into my laptop, then select SPDIF in as the input source. Captivate still gives the "... could not detect a recording device..." error, but the sound records anyway. This is kludgy, however.

Hi there
You may well just be out of luck. I heard Captivate 2 and Vista Pro used together. I don't believe Captivate was fully compliant with Vista until version 3. So that may explain things.
Unless someone pops in with a better idea, you should be able to record the audio separately, save as WAV or MP3 and import into your slides.
Cheers... Rick
Helpful and Handy Links
Captivate Wish Form/Bug Reporting Form
Adobe Certified Captivate Training
SorcerStone Blog
Captivate eBooks

Error: the backup disk image "/Volumes/Data/David's MacBook Air.sparsebundle" could not be accessed (error -1).

okay all of a sudden my TC 2 TB is not backing up.
O/S Lion
macbook air late 2011 model
error: he backup disk image “/Volumes/Data/David’s MacBook Air.sparsebundle” could not be accessed (error -1).
i don't see a sparse bundle file by name per se anywhere.
Also what is new: as soon as time machine auto kicks off or I manual kick it of, it opens a new window which contains one folder (my backup fies from other days) the files are "there", but I cannot successfully back up now?
i don't see a sparse bundle file by name per se anywhere.
Also what is new: as soon as time machine auto kicks off or I manual kick it of, it opens a new window which contains one folder (my backup fies from other days) the files are "there", but I cannot successfully back up now???

New 2 tb time capsule with air extreme built in. I can surf the net wirelessly through this device. And it had been backing up all along then a few days ago it stopped and reported that error.

The backup disk image "/Volumes/3TB Seagate Expansion Drive-1/Toby's MacBook Air.sparsebundle" could not be created (error (null)).

Hi all,
Recently moved into a new place and now have my external HDD plugged into my iMac as a backup.
Just went to backup my MacBook Air, which has used the drive previously, but always through USB.
Now trying to backup wirlelessly so I do not need to remove from my iMac, but got this message:
The backup disk image “/Volumes/3TB Seagate Expansion Drive-1/Toby’s MacBook Air.sparsebundle” could not be created (error (null)).
Have tried to reset without success. Any suggestions?
Thanks

You might want to consider starting a new discussion. Since this one is marked solved, less people are likely to look at it. You can link to this one.
The same error message? Try hooking your backup drive to your computer and run Disk Utility Repair Disk and Repair Permissions.

Nomad model# DAPAGO1 "Could not detect HDD" error

Similar Messages

Maybe you are looking for