NVIDIA driver won't load after running Radio Update

I have a mega 180 pc.   I recently had some problems while installing virus protection sw.  Long story short, I got it working again and tried running radio webupdate.  I didn't know what it did but my computer rebooted and now no longer works correctly.  I have restored most functionality with the exception of the following:
  * Internet no longer works
  * NVIDIA Geforce4 MX Integrated GPU will not load!
I consistenly get the following message when I try to load the driver
    "error occurred during the installation of device"
    "The required section was not found in the INF"
Any clue what is going on here and how I get this working again? 
I have noticed a few comments that radio webupdate is a "firmware" update software that supposedly works over the internet.  How can I tell which version of firmware I have? 
If I try to re-install the firmware from "MEGA 180 Firmware 0C.zip" using a dos boot disk will this correct my problem?   
Thanks, in advance...

flash the old firmware back to the Bluebird module. i don't think there is an update for the Mega 180, the RadioWebUpdate utility was only for the 651 i believe
not sure how it would affect anything else though, but you might like to try a Repair install of Windows to see if it will fix it. there is a sticky in the Operating Systems forum with detailed instructions

Similar Messages

  • External drives won't mount after running repair permissions

    None of my external drives will mount after running disk permissions. Drives work fine on my mbpro.
    None of the external drives show up in disk utilities...
    I've try shutting down and unplugging computer. even mini zip drives won't mount.
    I'm running 10.4.11
    PPC G5 2.3Ghz
    Thanks for any help..

    Repairing Permission only deals with installer receipts and system components. Not with mounting or accessing hard drives.
    Have your run Apple DU First Aid? Disk Warrior? Only use latest version for your OS.
    Are you trying to clone your system to external and then repairing permissions? trying to boot from them?
    If cloning, make sure the "Ignore Ownership" flag is unchecked before cloning (but do repair permissions on external drives you intend to boot from, such as a Firewire drive).
    What type of cases and interface are these?

  • IBook G4 won't load after latest security update, repair doesn't work?

    Hi I had the same problem as someone else in this forum:
    "Last night I saw that my ibook G4 wanted to do a security update. I told it to do it, and the ibook has not started since. It reset itself after downloaded, but it just stays on the booting up screen, never actually booting up so I can use it. After about two hours of trying to boot up, I turned it off, and on again, and it still wont boot.
    I really need suggestions as how I can fix it. Thanks
    ibook g4 Windows 2000
    Carolyn Samit
    Posts: 8,431
    From: Alameda CA Bay Farm Island
    Registered: Aug 5, 2005
    Re: G4 wont boot after latest security upgrade
    Posted: May 22, 2009 2:51 PM in response to: voiletmay
    Click to reply to this topic Reply email Email
    HI,
    Ok... you need to boot from your install disk.
    Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
    Go to Installer menu (Panther and earlier) or Utilities menu (Tiger and later) and launch Disk Utility.
    Select your HDD (manufacturer ID) in the left panel.
    Select First Aid in the Main panel.
    (Check S.M.A.R.T Status of HDD at the bottom of right panel. It should say: Verified)
    Click Repair Disk on the bottom right.
    If DU reports disk does not need repairs quit DU and restart.
    If DU reports errors Repair again and again until DU reports disk is repaired.
    If you cannot boot from your install disk, try booting in Safe Mode
    Resolve startup issues and perform disk maintenance with Disk Utility and fsck
    If you have the original hard drive in this iBook, it was probably a 60GB drive? When you can do this, check to see how much available disk space there is.
    Right or control click the MacintoshHD icon on your Desktop, then click: Get Info. In the Get Info window, click the discovery triangle so it's facing down. You will see; Capacity and Available Make sure you have 10% available disk space, 15% is better. Not enough available drive space can cause issues like you are experiencing.
    Carolyn "
    I tried restarting it after the repair (there were some things to repair and I tried to repair twice just to make sure it didn't miss anything) but it still won't load. It says its starting the OX system, but when the blue bar reaches the end, it doesn't do anything from there. I also left it on for hours and it did nothing. My mousepad still lets me move around the mouse, the caps lock key still lights up, as the num lock key. I tried safe mode but that won't load either...any other suggestions?

    *" I also left it on for hours and it did nothing. "*
    Your iBook needs to go in for repairs.
    Carolyn

  • Safari won't load after latest software update

    After the latest software update from Apple, Safari won't load. I've deleted the p.list and run OnyX to clean the system. It still won't load. This is a pain as Safari is my default browser and I have to get into Safari to change that. Has anyone else had this problem and fixed it?
    Thanks!
    Quicksilver G4   Mac OS X (10.4.5)   1.5Gb RAM

    Welcome Pauline;
    Actually you can change your default browser from within Mail, just go to Mail preferences and set the default browser to whatever you want. Unless you have cloned your system (before the update)which I heartily recommend,
    you may have to use Pacifist to extract Safari from
    the 10.4 installation package.
    Hope this helps,
    Miriam

  • My Toshiba external hard drive won't mount after OSX Mavericks update. Please help.

    Two days ago I updated to Mavericks 10.9.3 and prior to this, my Toshiba 1TB external hard drive worked perfectly well. Since the update, my hard drive will no longer mount. It shows up in Disk Utility but will not let me 'mount', 'verify disk' or 'repair disk' through Disk Utility. My sister has an identical Macbook Pro which she has not updated to Mavericks. I have tested my hard drive on her laptop and it works just fine. Can anyone tell me how to fix this? Do I need to reformat my hard drive (and if so, will that clear everything on my hard drive?) or is there a simple fix?
    Thank you for any assistance you can offer!

    Reset the NVRAM/PRAM and Reset the SMC, then try again.

  • Hard drive won't mount after running disk utility repair

    I have an iMac with a 320gb hard drive. It will not mount. The small horible wheel started sining so I retared. It could not find the start-up disk. I restared with the CD, after doing this twice the disk was visible in disk untility. I have ran this 3 times and it says the node is incorrect and it cannot be reapired by Disk Untility. It will not mount.
    Is there any other way to save the disk so I can get my files off.
    Any help is welcomed

    You would need the Firewire cable. If you get one then you can use Target Disk Mode - Transferring files between two computers using FireWire to transfer your files to another drive.

  • Internal hard drive won't mount after running Tech Tools Pro 5

    HELP.
    We have an imac 2ghz Intel Core 2 running OS 10.6.8.
    I ran Tech Tools Pro 5 to rebuild directory, optimize files, optimize volume. It ran over nightbut seemed to hang up optimizing the volume.
    Now the HD doesn't mount.
    I've tried a few fixes. Including running disk utility from a CD. The disk utility says the directory is okay but doesn't see the HD to verify or repair permissions.
    I've tried zapping the pram and safe boot, neither of which worked.
    I've been able to use the computer by booting from an external start up hd.
    Oddly, I ran a Time Machine back up prior to running TTP, but for some reason the only back up I see is from 3 months ago.
    Not sure why the recent back up didn't happen, but were missing some very important recent docs.
    I downloaded a trial version of Stellar Pheonix Mac Data Recovery and it seems to be able to see all of the data on the main HD.
    I'm wondering whether or not to spend $100 for full version to attempt to restore content of HD to an external.
    If I do this, I assume I'll have to erase the HD and reinstall data from the Stellar Pheonix collection, hoping that it's all intact.
    Does anyone have any other suggestions to get the HD mounted????

    Hi, never "Optimize" a drive before Repairing it AND having a backup clone to boot from.
    I assume I'll have to erase the HD and reinstall data from the Stellar Pheonix collection, hoping that it's all intact.
    No, I don't think you want an erase at all, you want a freah external drive to recover to first off.

  • Gmail won't load after Snow Leopard Update (safari 4.0.3)

    When I try and access gmail I get the following
    Safari can’t open the page.
    Safari can’t open the page “https://www.google.com/accounts/ServiceLogin?service=mail&passive=true&rm=false& continue=http%3A%2F%2Fmail.google.com%2Fmail%2F%3Fui%3Dhtml%26zy%3Dl&bsv=zpwhtyg jntrz&scc=1&ltmpl=default&ltmplcache=2” because Safari can’t establish a secure connection to the server “www.google.com”.
    Firefox loads gmail fine. I've do not have google gears installed and I've reset safari several times now. www.google.com wouldn't open at first, but after the rest it loaded. Gmail has not.
    Thanks in Advance

    After I installed Gears for Snow Leopard It worked fine.
    http://mailplaneapp.com/download/google_gears/
    Hope it will fix your problem as well.

  • The built in dictionaries I had downloaded before won't load after the ios8 update.

    When I had tried to define a word through the built in dictionaries on my iPad, nothing appeared as a definition. I went to the manage option to see if I needed to download the dictionaries again, but the dictionaries that I've already installed had these circles on the right that refused to fill up... i.e. They wouldn't load. I've tried downloading the other dictionaries I hadn't downloaded before to see if it was the overall downloading proble but nope, those download hella fine so... Help??????

    They'll be more updates. Try the rese belowt and if that doesn't work be sure to leave feedback to Apple.
    Press and hold both the home and power buttons 10-15 seconds till the Apple logo appears. Release both buttons. Wait 15-20 seconds till your iPad starts on it's own.
    http://www.apple.com/feedback/

  • IPhoto won't load after Mountain Lion update

    Since upgrading to Mountain Lion, my iPhoto will not open. The error message says I need to update my library in Aperature. I've opened the Library in Aperature but I get the same message when trying to open iPhoto again. Is there a way to reinstall iPhoto? Will that even help? 

    I had the same issue with each of iPhoto, Google Chrome, and the Kindle app.  Saw on another thread w/r/t the iPhoto issue, a recommendation to re-install Mountain Lion.  I did that, and now all 3 of those programs are working just fine.

  • Driver won't load

    I created a new boot cd with the BroadCom 57xx driver on it but the driver
    won't load. When I type the command in to load the driver it says that the
    file doesn't exist. If I change to the path it says it is getting the file
    from and load the file from there it loads. Is there anything I can do to
    get it to load at boot from the CD without having to load in manually?

    Aaron,
    It appears that in the past few days you have not received a response to your posting. That concerns us, and has triggered this automated reply.
    Has your problem been resolved? If not, you might try one of the following options:
    - Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
    - Check all of the other support tools and options available at http://support.novell.com in both the "free product support" and "paid product support" drop down boxes.
    - You could also try posting your message again. Make sure it is posted in the correct newsgroup. (http://support.novell.com/forums)
    If this is a reply to a duplicate posting, please ignore and accept our apologies and rest assured we will issue a stern reprimand to our posting bot.
    Good luck!
    Your Novell Product Support Forums Team
    http://support.novell.com/forums/

  • My apps won't load after updating to iOS4.3.2. What to do?

    My apps won't load after updating to iOS4.3.2. What to do?

    Yes, I tried that (thanks for the suggestion, though!). In my music app, when I click on certain songs, the screen moves to try to start the song, but then it bounces back to the menu screen without playing the song. On many albums, when I click on the first song, a song about halfway through the album will start to play rather than that first song. My other apps seems to be fixed, but not the music function.

  • Lightroom 5 won't load after 30 day trial of Lightroom3 error.

    I tried the 30 day trial of Lightroom 3 that I got with the Photoshop Elements 10 when I got my new computer.  The Lightroom loaded one picture and said I had an error and would try to find a solution.  I bought Lightroom5  and tried to install it and it keeps going back to the error of Lightroom 3 trial.  I tried to delete all programs associated with Lightroom and reinstall, but nothing happens.

    it just reads "Lightroom-Opening Catalog:New Years Day 2014 031.JPG.Ircat   assertion failed!
    New Years day 2014 is a folder and 031 is the picture in the folder that I tried to enhance in the 30 day free trial of Lightroom 3.  I bought Lightroom 5 from B &H and it appears to be hung up on the Lightroom 3 trial.
    kglad <[email protected]> wrote:
    kglad http://forums.adobe.com/people/kglad created the discussion
    "Re: Lightroom 5 won't load after 30 day trial of Lightroom3 error."
    To view the discussion, visit: http://forums.adobe.com/message/6048439#6048439

  • Mac won't boot after the latest update. It is loading the update and suddenly shuts down

    My MacBook Pro won't boot after a minor update. The update was all fine and my Mac acted like it used to but when I tried to boot my Mac it just loads the the update then goes back to the Apple logo and then shuts down.
    I hope that someone has got a solution because I do not want to restore my Mac for the 4th time.....

    Hello JonasHallund,
    We've an article that contains information and steps that can help get your MacBook Pro to boot again.
    Troubleshooting: My computer won't turn on
    http://support.apple.com/kb/TS1367
    Cheers,
    Allen

  • Old emails won't load after upgrade to Mountain Lion

    old emails won't load after upgrade to Mountain Lion

    See if anything in here will fix it:
    1. Hold down the Command and Option keys as you click the iPhoto icon.
    The Photo Library First Aid window opens:

Maybe you are looking for