Openboot disable NIC
Hi all. I have a Sunfire VT100 that I purchased off of eBay for training purposes. When I boot the server, I can't get past the part where it tries to resolve its IP address. I don't have the ethernet cable plugged in, b/c it would be pointless. Here is what the console says during boot:
Using Onboard Transceiver - Timeout waiting for AutoNegotiation
Status to be upd
ated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link
status. Check cable and try again.
Timeout waiting for AutoNegotiation Status
to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Setting up Network Link and Speed.
Using Onboard Transceiver -
Timeout waiting for AutoNegotiation Status to be upd
ated.
Timeout reading
Link status. Check cable and try again.
Timeout waiting for AutoNegotiation
Status to be updated. ... over and over.
From an "ok" prompt I type:
ok setenv tpe-link-test? false
Unknown option:
tpe-link-test?I'm not sure how I can get past this. Can someone point me in the right direction or tell me if there's a way to disable the NIC in openboot?
Cheers,
Edited by: spoonman on Aug 21, 2008 9:57 AM: clarify question
spoonman wrote:
Hi all. I have a Sunfire VT100 that I purchased off of eBay for training purposes. Did you install a new OS on it, or are you just trying to boot whatever was on there before?
When I boot the server, I can't get past the part where it tries to resolve its IP address. I don't have the ethernet cable plugged in, b/c it would be pointless.It may just be printing warnings about the link, but the boot halts for other reasons (needs to talk to NIS server would be a common reason).
From an "ok" prompt I type:
ok setenv tpe-link-test? false
Unknown option:
tpe-link-test?I'm not sure how I can get past this. Can someone point me in the right direction or tell me if there's a way to disable the NIC in openboot?Is there any reason not to just re-install the system?
You could do a single-user boot and remove the network from the active configuration, but who knows what else is going on with that OS.
Darren
Similar Messages
-
Disable NIC on Host but enable in VM - Hyper-V Core 2012
I have multiple NICs on my hyper-V Host.
I am running a router/firewall as a VM on this host. This is my perimeter/border protection.
The issue I am having is that one of the NICs on the Hyper-V host is dedicated to WAN connectivity for this VM. I want to somehow disable this NIC on the host but have it enabled for the router/firewall VM. Is this possible?
So logically, what I want is: Modem --> Router/Firewall VM --> rest of network (including other NICs on Hyper-V host)
Currently it is: Modem --> Hyper-V Host NIC --> Router/Firewall VM --> rest of network (including other NICs on Hyper-V host)
Obviously without doing anything, the host got assigned an IP and it had no firewall in front of it. I have since given it a static IP (10.0.0.24/255.255.255.224), but is there any way to just disable it on the host level?
Thanks!"I want to somehow disable this NIC on the host but have it enabled for the router/firewall VM. Is this possible?"
Absolutely. When you create the virtual switch on the physical NIC, one of the options is whether or not to expose it to the host operating environment. If you uncheck the box (the default is checked), the host does not have access to that NIC.
When you create an external switch, any connection to that switch will be made with a virtual NIC, including from the host. If you uncheck that box, no virtual NIC is created for the host.
.:|:.:|:. tim -
Enabling NICs in Server 2008 R2 Core
I'm looking for a way to enable the disabled NIC's on my 2008 R2 hyper-v host. Netsh cmd's only show the active interfaces and using device manager remotely is read only.
Also, is there an easy to uninstall the NIC's in Core and have Windows re-discover and re-install?
Any help here would be greatly appreciated.Hi
You could also try downloading Core Configurator 2.0 here http://coreconfig.codeplex.com/
It's a great little script that lets you do all the below.
Core Configuration tasks include:
Product Licensing
Networking Features
DCPromo Tool
ISCSI Settings
Server Roles and Features
User and Group Permissions
Share Creation and Deletion
Dynamic Firewall settings
Display | Screensaver Settings
Add & Remove Drivers
Proxy settings
Windows Updates (Including WSUS)
Multipath I/O
Hyper-V including virtual machine thumbnails
JoinDomain and Computer rename
Add/remove programs
Services
WinRM
Complete logging of all commands executed
Regards
Regards, ~P MCSE, MCITP, MCTS, MCP, CCNA -
Hello, everyone. I'm hoping this thread is in the right place.
I've been doing some research trying to understand logical switches/port profiles/etc. in VMM and have been having a hard time. Most of the articles I've found either don't go into enough detail or seem to lack proper examples. My goal is to enable NIC teaming
on my cluster hosts.
Currently, each cluster node has 1 standard switch per physical NIC. One of these NICs is trunked, and the others are not. Everything is working fine, but I'm looking to improve the infrastructure behind these hosts.
I evicted one node from the cluster to experiment with. I enabled LACP on the switch side (Cisco) and enabled NIC teaming on the server (2012 R2). The server is online and functioning, but this is where my knowledge ends. I can't create a logical switch
and add it to this host as the job fails stating that the switch can't be added since the host is already teamed. I'm a little confused about the proper process of getting a logical switch created and added to my host. Do I need to remove LACP and disable
NIC teaming on the host and then re-enable it? Am I going down the wrong path by using LACP?
Any tips and advice would be greatly appreciated. I'd also be happy to provide any additional details I may have left out.We use LACP teaming for four NICs, two teams, one Production vSwitch and one for management.
We create the management team on the HyperV host first, add it into VMM then push out a team FROM VMM for the switch. The trick is to create a port profile (using algorithm Hyper-V Port and Teaming Mode LACP.) bind this port profile to your logical network(s).
then create your virtual switch and select uplink mode TEAM. and add in your uplink port profile.
Once you have done this you can then right click the host (in VMs and Services) Properties and navigate to virtual switches. Add a new Virtual Switch (New logical switch) then you will be able to add multiple adapters to the switch.
Hit apply and it *should* team for you.
If you need further clarification I can send screen prints and exact steps on tuesday when i'm back in the office. -
Server 2012 R2 slow performance over all
This is a DELL PowerEdge R820 / 256GB RAM / 4TB onboard storage configured as Remote Desktop Services Host /TS... running QuickBooks, MS Office 2010 STD, Symantec EndPoint Protection (basic antivirus installation ONLY)... 1 month old server... SUPER fast,
super powerfull.... Part of an AD in SBS 2008 Premium... single NIC card 4 ports / 3 ports disabled. single IP... no VLANS... server is able to resolve ANY pc, DNS record with no problems... able to resolve DC by name, able to receive GP, able to update, able
to do everything that I can think of.... EXCEPT... anything I open, word, excel, QuickBooks, IE.... takes forever to open... after the application is open is fast but to open anything takes 3-4 minutes.... open ticket with Symantec all looks good, created
lots of exceptions for antivirus/real time scanning, open ticket with QuickBooks: files look good application was removed and reinstalled to be sure all was done correctly... check the binding order for the disabled NIC; the active one is TOP option, no errors
at all in event viewers for system, application, setup, no errors at all in DELL management tool, no hard drive errors, no controllers errors.... this server is replacing an old dell poweredge 2008 STD with 24GB RAM... the old DELL opens the same applications
way faster than the new one... same Quicken version; old server opens Quicken in seconds, new one 3-4 minutes..... Real time monitoring NEVER goes above 1% for CPU and 3% for memory utilization.... one more thing... removed antivirus 100% restart... same performance
without antivirus.....
Any ideas will be great as of how to troubleshoot the slow performance....
Thank you!Hi,
As Sam suggested, please check if there any issue occurred in hard drive.
On current situation, please also refer to following steps and troubleshoot, then check if we can find more
clues.
Please check if you have installed all necessary updates for the Windows Server 2012 R2.
Please
perform a clean boot to check if there has software conflicts.
Please use Resource Monitor to troubleshoot and check if we can find some more details.
Using Resource Monitor to Troubleshoot Windows Performance Issues Part 1
Using
Resource Monitor to Troubleshoot Windows Performance Issues Part 2
If any update, please feel free to let me know.
Hope this helps.
Best regards,
Justin Gu -
TS 140 Windows Server 2012 R2 install failure error 0x80070570
Recently bought 2 TS140 70A4001PUX servers with Xeon E3 1245 v3 attempting to install eval version of server 2012 R2 (latest on site April refresh) and keep getting the following error at around 62% in the getting files ready for installation:
Windows can not install required files. The file may be corrupt or missing. Make sure all files required for installation are available, and restart the installation. Error code: 0x80070570
I have seen web search results for various MS OSes that indicate this is due to bad memory, corrupt installation media or download, Nic cards, BIOS settings etc.
To rule out memory ran memtest for hours with no errors against the crucial 32GB mem 2 (CT2KIT102472BD160B) also tried installing against the 4GB mem that came with the system. I think I have done enough to rule out the memory.
Installation media, I downloaded the ISO from Microsoft's eval site three different times using Firefox, Chrome and IE burned the image to DVD 2 different times and tried numerous times using Rufus on an 8GB USB stick in different USB ports. I’ve tried installing the datacenter version with both GUI and server core options. Next thing I’m going to try is to install Server 2012 from an older ISO that I have used successfully many times in the past will update later though I would prefer to install fresh from R2.
I also have the Lenovo 1GBPS Ethernet I350-T2 Server adapter by Intel for ThinkServer. I have tried installing with it inserted and with it removed, also with nothing even disabling the on board Nic in the BIOS. Same result.
The SSD drive I have is the Samsung 850 Pro 128GB. After the failure I am able to mount this drive on another machine and see that a significant amount of files get copied to it so I ruled out the sata cable. I also tried with another no SSD WD HD with the same result. I even break out at install run dispart and clean the partitions.
Excerpts from setupact.log on SSD:
2015-03-24 13:58:37, Info [0x0606cc] IBS Calling WIMApplyImage (flags = 0x180)...
[800] [UncompressFile994) -> file corrupted in block at offset 000000541283B3F2] G:\Windows\System32\DriverStore\FileRepository\netelx.inf_amd64_82d20ebbcbf8b5af\netelx.PNF (Error = 1392)
2015-03-24 13:59:54, Error [0x0606cc] IBS WIMApplyImage failed; hr = 0x80070570[gle=0x00000570]
2015-03-24 13:59:54, Error [0x0600a1] IBS DeployImage:Image application failed; hr = 0x80070570[gle=0x00000057]
For BIOS settings I have reverted back to defaults tried IDE instead of AHCI and also tried CSM support enabled and disabled, NIC both enabled disabled.
Any suggestions would greatly be appreciated.
Thanks.
Solved!
Go to Solution.In case anyone is interested the Server 2012 R@ eval ISO I had issues with is the following file:
9600.17050.WINBLUE_REFRESH.140317-1640_X64FRE_SERVER_EVAL_EN-US-IR3_SSS_X64FREE_EN-US_DV9.ISO
I am also reporting this to MS. -
DC on VM Restored after crash - Does Not allow PCs to Join Domain, or Domain Users to Log in
We currently had a RAID array crash and rebuilt our main server which housed VMs for our Web and DC.
The main server was restored from a bare-metal backup from 6 months prior to the latest backup of the VMs (not sure if pertinent)
Since the Restore, Domain computers cannot access file shares on the main server or VMs - "unspecified network error
0x80004005
Removed the main server from the Domain to re-join it due to some issues with logging in (even with a Domain Admin account) - Found that any PC removed from the domain was no longer able
to rejoin - Receive (Network path was not found error)
Domain Users cannot log in to their computers - Error reads "The trust relationship between this computer and the domain has been lost" - Domain Admin accounts can log in without
problem.
Have been working on it for two weeks and tried most of the things that I have found in others questions for related
DCDIAG results (run on DC VM) - More errors appear if run on the Server (Locator DcGetDcName(GC_Server_Required) call failed, error 1722 (same for PDC, TIME, GOOD_TIME, and KDC)
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
Home Server = DC1
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site-Name\DC1
Starting test: Connectivity
......................... DC1 passed test Connectivity
Doing primary tests
Testing server: Default-First-Site-Name\DC1
Starting test: Advertising
......................... DC1 passed test Advertising
Starting test: FrsEvent
There are warning or error events within the last 24 hours after the
SYSVOL has been shared. Failing SYSVOL replication problems may cause
Group Policy problems.
......................... DC1 failed test FrsEvent
Starting test: DFSREvent
......................... DC1 passed test DFSREvent
Starting test: SysVolCheck
......................... DC1 passed test SysVolCheck
Starting test: KccEvent
......................... DC1 passed test KccEvent
Starting test: KnowsOfRoleHolders
......................... DC1 passed test KnowsOfRoleHolders
Starting test: MachineAccount
......................... DC1 passed test MachineAccount
Starting test: NCSecDesc
......................... DC1 passed test NCSecDesc
Starting test: NetLogons
......................... DC1 passed test NetLogons
Starting test: ObjectsReplicated
......................... DC1 passed test ObjectsReplicated
Starting test: Replications
......................... DC1 passed test Replications
Starting test: RidManager
......................... DC1 passed test RidManager
Starting test: Services
......................... DC1 passed test Services
Starting test: SystemLog
A warning event occurred. EventID: 0x80040022
Time Generated: 01/15/2015 19:32:28
Event String:
The driver disabled the write cache on device \Device\Harddisk0\DR0.
A warning event occurred. EventID: 0x80040022
Time Generated: 01/15/2015 19:32:28
Event String:
The driver disabled the write cache on device \Device\Harddisk0\DR0.
A warning event occurred. EventID: 0x80040022
Time Generated: 01/15/2015 19:32:28
Event String:
The driver disabled the write cache on device \Device\Harddisk0\DR0.
A warning event occurred. EventID: 0x000003F6
Time Generated: 01/15/2015 19:32:52
Event String:
Name resolution for the name DC1.Home.xxx.com timed out after none of the configured DNS servers responded.
An error event occurred. EventID: 0xC00038D6
Time Generated: 01/15/2015 19:33:25
Event String:
The DFS Namespace service could not initialize cross forest trust information on this domain controller, but it will periodically retry the operation. The return code is in the record data.
A warning event occurred. EventID: 0x00000420
Time Generated: 01/15/2015 19:33:29
Event String:
The DHCP service has detected that it is running on a DC and has no credentials configured for use with Dynamic DNS registrations initiated by the DHCP service. This is not a recommended security configuration.
Credentials for Dynamic DNS registrations may be configured using the command line "netsh dhcp server set dnscredentials" or via the DHCP Administrative tool.
A warning event occurred. EventID: 0x00002724
Time Generated: 01/15/2015 19:33:33
Event String:
This computer has at least one dynamically assigned IPv6 address.For reliable DHCPv6 server operation, you should use only static IPv6 addresses.
A warning event occurred. EventID: 0x000727AA
Time Generated: 01/15/2015 19:36:34
Event String:
The WinRM service failed to create the following SPNs: WSMAN/DC1.Home.xxx.com; WSMAN/DC1.
A warning event occurred. EventID: 0x00001695
Time Generated: 01/15/2015 19:59:52
Event String:
Dynamic registration or deletion of one or more DNS records associated with DNS domain 'Home.xxx.com.' failed. These records are used by other computers to locate this server as a domain controller (if the specified
domain is an Active Directory domain) or as an LDAP server (if the specified domain is an application partition).
A warning event occurred. EventID: 0x00001695
Time Generated: 01/15/2015 19:59:52
Event String:
Dynamic registration or deletion of one or more DNS records associated with DNS domain 'DomainDnsZones.Home.xxx.com.' failed. These records are used by other computers to locate this server as a domain controller
(if the specified domain is an Active Directory domain) or as an LDAP server (if the specified domain is an application partition).
A warning event occurred. EventID: 0x00001695
Time Generated: 01/15/2015 19:59:52
Event String:
Dynamic registration or deletion of one or more DNS records associated with DNS domain 'ForestDnsZones.Home.xxx.com.' failed. These records are used by other computers to locate this server as a domain controller
(if the specified domain is an Active Directory domain) or as an LDAP server (if the specified domain is an application partition).
A warning event occurred. EventID: 0x00000420
Time Generated: 01/15/2015 20:20:21
Event String:
The DHCP service has detected that it is running on a DC and has no credentials configured for use with Dynamic DNS registrations initiated by the DHCP service. This is not a recommended security configuration.
Credentials for Dynamic DNS registrations may be configured using the command line "netsh dhcp server set dnscredentials" or via the DHCP Administrative tool.
A warning event occurred. EventID: 0x00002724
Time Generated: 01/15/2015 20:20:25
Event String:
This computer has at least one dynamically assigned IPv6 address.For reliable DHCPv6 server operation, you should use only static IPv6 addresses.
......................... DC1 failed test SystemLog
Starting test: VerifyReferences
......................... DC1 passed test VerifyReferences
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test
CrossRefValidation
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test
CrossRefValidation
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Running partition tests on : Home
Starting test: CheckSDRefDom
......................... Home passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Home passed test CrossRefValidation
Running enterprise tests on : Home.xxx.com
Starting test: LocatorCheck
......................... Home.xxx.com passed test LocatorCheck
Starting test: Intersite
......................... Home.xxx.com passed test Intersite
All PCs can ping the DC, and get name resolution. Checked IPs, DNS on both WS and DC (DC points to its own IP address with no other DNS), Forwarders for DNS appear to be working,
as normal DNS name resolution and internet access works on all PCs. Have tried disabling NIC card and installing another NIC. All searches keep pointing back at the same things that I have tried. I feel like I am missing something stupid.
Please helpThe backup you used is too old. That is why your clients are experiencing trust relationship failures: the computer passwords are no longer matching so they are failing to connect to AD. You need to disjoin and join them again.
I understand that this is the only DC you have so please make sure that the DC is not multihomed, that it points to its private IP address as primary DNS server and 127.0.0.1 as secondary one. Also, you might need to rebuild your SYSVOL folder if you keep
getting the SYSVOL errors: https://support.microsoft.com/kb/315457?wa=wsignin1.0
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile -
Hi,
Just a few days back when i was surfing the net and the computer suddenly restarts and I get this Blue Screen and at the end it says,"Beginning to Dump Physical Memory". I restarted the computer and then no error message. The next
day when to try to ON the computer i get this PXE-e53 No File Name Received and with some realtek external Controller stuff on top. I shut downed the computer. Next day no errors. I started surfing the net about this
PXE-MOF problem and found out that The Boot Device Priority in BIOS would solve it. I tried it and it was fine for that time only.
Next day I ON the PC -same error, restart it(works) and again surf the net and found out that I have to Disable NIC configuration and check the cables of HDD. When i went and searched in the BIOS and couldn't find NIC. But did find a Boot To Network in the
Boot Tab and i disabled it. It removed 'Ethernet' from the Boot Device Priority. I save it and restart the PC and this time I get a message " Boot Failure. Press Any Key To Continue". I restarted and enable Boot to Network in BIOS and I get the PXE
error again.I Restarted the PC and restored Defaults in BIOS but same error(PXE).
Next day I asked my Dad to open the PC and check the cables. He opened it and removed the two cables attached to the HDD (Hard Disk Drive) and then he removed the dust from the HDD and put everything back into place. We ON the PC and it finally worked....................
I go to the bedroom and when I return I see this irritating Blue screen again ( the same one at the start). We restart it and no effect- I get the same PXE error. When i put a usb and on the computer an error comes saying," Disk Error Please click to
Restart "
The thing is I cannot replace or format the hard disk since it has some important files and I don't have backup for them :( so what do I do???
Would doing a repair using Windows XP CD work? or would changing the OS work?
Please tell me what to do
I want to know what is causing it and what do I have to do to repair the fault and what should I do to prevent it in future?
My Computer Configurations
Windows XP Professional Service Pack 2
2.00 GB Ram
Intel Dual Core 2 e7400 2.80 GHz
PLEASE HELP ME
And ya im planning to change the OS only after recovering my filesHere is what I recommend:
Ask a friend to help you manufacture an
Ubuntu boot CD.
Change your BIOS boot order so that the machine boots off this CD.
Save your important files to flash stick.
Furthermore:
Spending time and effort on a Windows XP machine seems a little pointless, seeing that Microsoft will cease supporting this operating system a few weeks from now.
Files that are not backed up regularly are lost files. It is only a matter of time. Lots of people ignore this rule until they suffer a major catastrophe. You're probably safe this time but you might want to use this incident as an incentive to set up a
robust backup scheme (unless you prefer to wait for the big disaster such as a disk crash). -
8.1 can't shut down after installing itunes
I recently reformatted and did a clean install of window's 8.1
I have done all updates, both windows and drivers and the machine is very smooth and stable.
After installing iTunes the computer will no longer shut down, it displays the logging off / shutting down screen but then just reboots.
I have attempted numerous resolutions to no avail, i.e. disabled NIC as bootable device, disabled the hybrid boot feature & flashed and tweaked some BIOS settings.
The computer will not even shut down when I give the command "shutdown /s /t 0"
I only had Windows Office and iTunes installed on the computer and suspecting that iTunes may be the culprit, I uninstalled it and now the computer shuts down without any issue.
I have since read several threads about iTunes and shutdown/restart issues with 64 bit versions of Windows although I have not found anyone else with my exact issue.
Is anyone aware of a resolution for this?
For now I will need to install iTunes so I can sync my phone and then uninstall so I can shut down!Fingers crossed there will be an update for this, I was lucky that my install so was new that there weren't very many things that could have caused it because I don't think it would have ever occurred to me that iTunes was the issue.
I literally tried every other possibility before waking up in the middle of the night and realizing that the problem started right after I installed iTunes.
I have had issues with Apple software in the past where I attempt to disable it from launching automatically when I boot the computer and it will simply create another entry for itself in the startup list.
If I disable that one it makes another, and another and another.... It's like the freaking Apple hydra.
The want me to know how much I need them! lol -
after installing hyper-v,when i choose external network option,it disables nic card feature and all the features of nic card go to the virtual swich which i create to connect that with external network.how to solve this problem,please,help.
Hi SUBHRAJITPYNE,
" It disables nic card feature and all the features of nic card go to the virtual swich which i create to connect that with external network
Do you mean the original configuration of physical NIC was migrated in to the new external Vswitch after you created a new external Vswitch , right?
I want to say it is normal , because the option " allow management operating system..." was checked by default .
If you do not want hyper-v host to access outside via this physical NIC you can uncheck this option.
Hope this helps
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Can't start imported VirtualBox appliance on Arch host with errors
(I have been referred here from this thread in the VirtualBox forums because it is suspected that the problem is Arch-specific)
I've installed latest VirtualBox 4.0.4 via pacman in a fully updated Arch Linux system.
Then, I successfully imported the Zero Effort Groupware (ZEG) 1.3.5 appliance (which is an Ubuntu guest virtual machine) into VirtualBox. I followed all the instructions on the appliance's website to do so.
When I try to start the virtual machine I get:
VBoxManage startvm ZEG-1.3.5
Waiting for the VM to power on...
VBoxManage: error: The virtual machine 'ZEG-1.3.5' has terminated unexpectedly during startup with exit code 1
VBoxManage: error: Details: code NS_ERROR_FAILURE (0x80004005), component Machine, interface IMachine, callee
I also tried running it headless and got:
VBoxHeadless --startvm "ZEG-1.3.5" &
[1] 1073
[penyuan@nycticebus ~]$ Oracle VM VirtualBox Headless Interface 4.0.4_OSE
(C) 2008-2011 Oracle Corporation
All rights reserved.
VRDE server is listening on port 3389.
Error: failed to start machine. Error message: Failed to open/create the internal network 'HostInterfaceNetworking-en0: Ethernet' (VERR_INTNET_FLT_IF_NOT_FOUND).
Failed to attach the network LUN (VERR_INTNET_FLT_IF_NOT_FOUND).
Unknown error creating VM (VERR_INTNET_FLT_IF_NOT_FOUND)
[1]+ Done VBoxHeadless --startvm "ZEG-1.3.5"
I don't know what to make of it, I would appreciate any help you can provide as soon as possible. Thanks!
P.S. Here is what "VBoxManage showvminfo ZEG-1.3.5" shows:
BoxManage showvminfo ZEG-1.3.5
Name: ZEG-1.3.5
Guest OS: Ubuntu
UUID: 506a8072-2b85-4ac6-bd91-ff37406ebe73
Config file: /home/penyuan/VirtualBox VMs/ZEG-1.3.5/ZEG-1.3.5.vbox
Snapshot folder: /home/penyuan/VirtualBox VMs/ZEG-1.3.5/Snapshots
Log folder: /home/penyuan/VirtualBox VMs/ZEG-1.3.5/Logs
Hardware UUID: 506a8072-2b85-4ac6-bd91-ff37406ebe73
Memory size: 1024MB
Page Fusion: off
VRAM size: 12MB
HPET: off
Chipset: piix3
Firmware: BIOS
Number of CPUs: 1
Synthetic Cpu: off
CPUID overrides: None
Boot menu mode: message and menu
Boot Device (1): DVD
Boot Device (2): HardDisk
Boot Device (3): Not Assigned
Boot Device (4): Not Assigned
ACPI: on
IOAPIC: off
PAE: on
Time offset: 0 ms
RTC: UTC
Hardw. virt.ext: on
Hardw. virt.ext exclusive: off
Nested Paging: on
Large Pages: off
VT-x VPID: on
State: powered off (since 2011-04-04T01:37:14.000000000)
Monitor count: 1
3D Acceleration: off
2D Video Acceleration: off
Teleporter Enabled: off
Teleporter Port: 0
Teleporter Address:
Teleporter Password:
Storage Controller Name (0): IDE Controller
Storage Controller Type (0): PIIX4
Storage Controller Instance Number (0): 0
Storage Controller Max Port Count (0): 2
Storage Controller Port Count (0): 2
Storage Controller Bootable (0): on
Storage Controller Name (1): SATA Controller
Storage Controller Type (1): IntelAhci
Storage Controller Instance Number (1): 0
Storage Controller Max Port Count (1): 30
Storage Controller Port Count (1): 1
Storage Controller Bootable (1): on
IDE Controller (1, 0): Empty
SATA Controller (0, 0): /home/penyuan/VirtualBox VMs/ZEG-1.3.5/ZEG-1.3.5-disk1.vmdk (UUID: 7046c046-ae41-4bfe-9a52-9dd389bb8cf2)
NIC 1: MAC: 080027CC69E3, Attachment: Bridged Interface 'en0: Ethernet', Cable connected: on, Trace: off (file: none), Type: 82540EM, Reported speed: 0 Mbps, Boot priority: 0
NIC 2: disabled
NIC 3: disabled
NIC 4: disabled
NIC 5: disabled
NIC 6: disabled
NIC 7: disabled
NIC 8: disabled
Pointing Device: PS/2 Mouse
Keyboard Device: PS/2 Keyboard
UART 1: disabled
UART 2: disabled
Audio: disabled
Clipboard Mode: Bidirectional
VRDE: disabled
USB: disabled
USB Device Filters:
<none>
Available remote USB devices:
<none>
Currently Attached USB Devices:
<none>
Shared folders: <none>
VRDE Connection: not active
Clients so far: 0
Guest:
OS type: Ubuntu
Additions run level: 0
Configured memory balloon size: 0 MBskunktrader wrote:The error message seems to suggest that the module vboxnetflt is not loaded
1. I added vboxnetflt to the modules list in rc.conf, is there somewhere else I should add it?
2. Just to be sure, I did "modprobe vboxnetflt" then tried to run the virtual machine, but still got:
Oracle VM VirtualBox Headless Interface 4.0.4_OSE
(C) 2008-2011 Oracle Corporation
All rights reserved.
VRDE server is listening on port 3389.
Error: failed to start machine. Error message: Failed to open/create the internal network 'HostInterfaceNetworking-en0: Ethernet' (VERR_INTNET_FLT_IF_NOT_FOUND).
Failed to attach the network LUN (VERR_INTNET_FLT_IF_NOT_FOUND).
Unknown error creating VM (VERR_INTNET_FLT_IF_NOT_FOUND)
What could be the problem? Thanks. -
[SOLVED] Virtualbox list usb devices is empty.
I moved from virtualbox_bin(AUR) to virtualbox(community), and remove /proc/bus/usb entry in /etc/fstab, after that the usb doesn't work. I can check 'Enable USB 2.0 (EHCI) Controller' in Virtualbox settings, but can't find any available usb devices.
$ pacman -Qs virtualbox
local/virtualbox 4.1.22-1
Powerful x86 virtualization for enterprise as well as home use
local/virtualbox-additions 4.1.22-1
The official all-in-one VirtualBox Guest Additions ISO/CD image
local/virtualbox-ext-oracle 4.1.22-1
Oracle VM VirtualBox Extension Pack
local/virtualbox-hook 2.1-1
mkinitcpio hook to compile the virtualbox modules
local/virtualbox-modules 4.1.22-1
Kernel modules for VirtualBox
local/virtualbox-source 4.1.22-1
VirtualBox kernel modules source
$ VBoxManage list usbhost
Host USB Devices:
<none>
$ ls /dev/usbbox
ls: cannot access /dev/usbbox: No such file or directory
$ groups
log kvm network video audio optical storage users vboxusers guten input libvirt davfs2 virtftp
$ lsusb
Bus 001 Device 002: ID 0424:2513 Standard Microsystems Corp. 2.0 Hub
Bus 001 Device 003: ID 05ac:8509 Apple, Inc. FaceTime HD Camera
Bus 002 Device 002: ID 0424:2513 Standard Microsystems Corp. 2.0 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth)
Bus 001 Device 005: ID 05ac:0252 Apple, Inc. Internal Keyboard/Trackpad (ANSI)
Bus 002 Device 003: ID 05ac:8242 Apple, Inc. IR Receiver [built-in]
Bus 002 Device 004: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
Bus 001 Device 008: ID 05ac:821a Apple, Inc. Bluetooth Host Controller
Bus 002 Device 005: ID 046d:c05a Logitech, Inc. Optical Mouse M90
Bus 002 Device 008: ID 0951:1624 Kingston Technology DataTraveler G2 4GB Pen Drive
Bus 002 Device 007: ID 413c:2003 Dell Computer Corp. Keyboard
Last edited by GutenYe (2012-09-17 12:38:58)I am having the same problem and have tried "everything" and still cannot get it to work.
calpoly@arch:~$ cat /etc/group | grep vboxusers
vboxusers:x:108:calpoly,root
calpoly@arch:~$ lsusb
Bus 004 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 05ac:12a0 Apple, Inc. iPhone 4S
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 046d:c52f Logitech, Inc. Unifying Receiver
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
calpoly@arch:~$ sudo pacman -Qs virtualbox
local/virtualbox 4.3.6-3
Powerful x86 virtualization for enterprise as well as home use
local/virtualbox-guest-dkms 4.3.6-3
VirtualBox Guest kernel modules sources
local/virtualbox-guest-modules 4.3.6-4
Guest kernel modules for VirtualBox
local/virtualbox-guest-utils 4.3.6-3
VirtualBox Guest userspace utilities
local/virtualbox-host-modules 4.3.6-4
Host kernel modules for VirtualBox
local/virtualbox-host-modules-lts 4.3.6-5
Host kernel modules for VirtualBox
calpoly@arch:~$ sudo VBoxManage controlvm windowSeven usbattach 609c101d-ef6a-401a-ad15-306f3e7bc8ae
VBoxManage: error: The USB device with UUID {00000010-0030-0000-90f9-0560b57f0000} is not currently attached to the host
VBoxManage: error: Details: code NS_ERROR_INVALID_ARG (0x80070057), component USBProxyService, interface IHost, callee nsISupports
VBoxManage: error: --------
VBoxManage: error: Could not load the Host USB Proxy service: VERR_NOT_FOUND
VBoxManage: error: Details: code Unknown Status 0x4005 (0x4005), component Host, interface IHost
VBoxManage: error: Context: "AttachUSBDevice(usbId.raw())" at line 973 of file VBoxManageControlVM.cpp
calpoly@arch:~$ sudo VBoxManage showvminfo windowSeven
Name: windowSeven
Groups: /
Guest OS: Windows 7
UUID: 609c101d-ef6a-401a-ad15-306f3e7bc8ae
Config file: /root/VirtualBox VMs/windowSeven/windowSeven.vbox
Snapshot folder: /root/VirtualBox VMs/windowSeven/Snapshots
Log folder: /root/VirtualBox VMs/windowSeven/Logs
Hardware UUID: 609c101d-ef6a-401a-ad15-306f3e7bc8ae
Memory size: 2048MB
Page Fusion: off
VRAM size: 128MB
CPU exec cap: 100%
HPET: off
Chipset: piix3
Firmware: BIOS
Number of CPUs: 2
PAE: off
Long Mode: off
Synthetic CPU: off
CPUID overrides: None
Boot menu mode: message and menu
Boot Device (1): DVD
Boot Device (2): HardDisk
Boot Device (3): Network
Boot Device (4): Floppy
ACPI: on
IOAPIC: on
Time offset: 0ms
RTC: local time
Hardw. virt.ext: on
Nested Paging: on
Large Pages: off
VT-x VPID: on
VT-x unr. exec.: on
State: powered off (since 2014-02-11T12:16:18.000000000)
Monitor count: 1
3D Acceleration: off
2D Video Acceleration: off
Teleporter Enabled: off
Teleporter Port: 0
Teleporter Address:
Teleporter Password:
Tracing Enabled: off
Allow Tracing to Access VM: off
Tracing Configuration:
Autostart Enabled: off
Autostart Delay: 0
Default Frontend:
Storage Controller Name (0): IDE
Storage Controller Type (0): PIIX4
Storage Controller Instance Number (0): 0
Storage Controller Max Port Count (0): 2
Storage Controller Port Count (0): 2
Storage Controller Bootable (0): on
Storage Controller Name (1): SATA
Storage Controller Type (1): IntelAhci
Storage Controller Instance Number (1): 0
Storage Controller Max Port Count (1): 30
Storage Controller Port Count (1): 1
Storage Controller Bootable (1): on
IDE (1, 0): Empty
SATA (0, 0): /media/disk/VirtualBox OS X HDD/windowSeven.vdi (UUID: 5c44157f-350a-467c-a988-b4cfb8635fd5)
NIC 1: MAC: 0800279A3907, Attachment: NAT, Cable connected: on, Trace: off (file: none), Type: 82540EM, Reported speed: 0 Mbps, Boot priority: 0, Promisc Policy: deny, Bandwidth group: none
NIC 1 Settings: MTU: 0, Socket (send: 64, receive: 64), TCP Window (send:64, receive: 64)
NIC 2: disabled
NIC 3: disabled
NIC 4: disabled
NIC 5: disabled
NIC 6: disabled
NIC 7: disabled
NIC 8: disabled
Pointing Device: PS/2 Mouse
Keyboard Device: PS/2 Keyboard
UART 1: disabled
UART 2: disabled
LPT 1: disabled
LPT 2: disabled
Audio: enabled (Driver: ALSA, Controller: HDA)
Clipboard Mode: Bidirectional
Drag'n'drop Mode: Bidirectional
VRDE: disabled
USB: enabled
EHCI: enabled
USB Device Filters:
<none>
Available remote USB devices:
<none>
Currently Attached USB Devices:
<none>
Bandwidth groups: <none>
Shared folders:
Name: 'music', Host path: '/media/disk/music' (machine mapping), writable
VRDE Connection: not active
Clients so far: 0
Video capturing: active
Capture screens: 0
Capture file: /root/VirtualBox VMs/windowSeven/windowSeven.webm
Capture dimensions: 1024x768
Capture rate: 1024 kbps
Capture FPS: 25
Guest:
Configured memory balloon size: 0 MB
calpoly@arch:~$ sudo modprobe vboxdrv
calpoly@arch:~$ sudo modprobe -a vboxguest vboxsf vboxvideo
modprobe: ERROR: could not insert 'vboxguest': No such device
modprobe: ERROR: could not insert 'vboxsf': No such device
calpoly@arch:~$ sudo modprobe vboxnetflt
calpoly@arch:~$ sudo modprobe vboxsf
modprobe: ERROR: could not insert 'vboxsf': No such device
calpoly@arch:~$ sudo VBoxManage list usbhost
Host USB Devices:
<none>
Have rebooted and reinstalled virtualbox multiple times to no avail.
It is important to note that my iPhone used to sync with iTunes on Windows 7 in Virtualbox, but then I removed the USB filter and did some updates and now it no longer works.
I have spent many more hours than I care to admit on this problem, so please, any help is welcome.
Last edited by Kg4XmtUSyxd8B9M7Ex&&KXZGF (2014-02-11 12:33:00) -
Windows 2003 Server reboot but not unexpected, couldnt find the trigger for reboot
Hi All,
I have windows 2003 Server 32 bit,std. Which is getting rebooted every 2 days once at 5 AM. I couldnt find the cause for the reboot. Need
I dont see anything in system log apart from event 6006 (event log service stopped).
Enabled advanced Auditing , nothing suspecious found.
No scheduled task or job.
Antivirus scan is clean, no internet access to the box.
Its Virtual machine, all other VM's hosted on ESX server (where the machine with issue hosted) are working fine.
Removed all users admin rights.
Disabled NIC to check if the reboot intiatation happening from network, however server still reboots at 5.
Run process monitor and saved the file at 4:59:38 AM (just before the reboot), nothing supecious found.
Its used for build , various versions of Visual Studio is installed on the box and other tools are installed too.
However could not find a reason or log to find what is causing these reboot.
Need a direction on troubleshooting this urgently.
In application event log i see below.
The description for Event ID ( 0 ) in Source ( Poweroff ) cannot be found. The local computer may not have the necessary registry information or message DLL files to display messages from a remote computer. You may be able to use the /AUXSOURCE= flag to
retrieve this description; see Help and Support for details. The following information is part of the event: ExitWindowsEx executed succesfully!.
The description for Event ID ( 0 ) in Source ( Poweroff ) cannot be found. The local computer may not have the necessary registry information or message DLL files to display messages from a remote computer. You may be able to use the /AUXSOURCE= flag to
retrieve this description; see Help and Support for details. The following information is part of the event: Initiating FORCE REBOOT.Hi,
I agree with Dave Patrick, please confirm there have any software trigger the Windows restart API, and please refer the following hotfix scenario applied to your environment
or not.
More information:
You may experience an abnormal shutdown on a Windows Server 2003-based computer after the Windows logon screen saver starts
http://support.microsoft.com/kb/916719/en-us
Why Windows NT Reports 6005, 6006, 6008, and 6009 Event Log Entries
http://support.microsoft.com/kb/196452/en-us
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
How do I stop Automatic Graphics Switching setting automatically reverting
Macbook Pro 15" Mid 2010
OS X 10.7.4
I have a recurring problem where my screen (built in or external monitor/projector) will just go blank at random times. It is an unrecoverable situation and I have to do a hard power reset to get working again.
After testing several theories without success I struck upon one that showed promise. The blanking tended to occur when I was in Lion Fullscreen mode, or using a gesture to start expose - so I figured maybe it was a graphics switching issue.
So I went into System Preferences and disabled 'Automatic graphics switching'. I then ran trouble free for several days (I was typically crashing 1-2 times a day)
Then several days later it happened again and I thought I was back to square one. However, a colleague suggested I check the graphic switching setting to see if something had changed it back, and sure enough it was re-enabled.
Now I find myself in a constant battle with the system to keep disabling the 'Automatic graphics switrhing' in System Preferences.
I have tried setting it and locking it, but sooner or later it reverts.
I need to know if it is possible to force it to stay disabled.Nice pace both of you - cheers.
I have downloaded and installed now (cos I implicitly trust all links in forum responses )
Oddly enough, since typing my original question this morning (local time) and installing this little utility this afternoon, the setting had once more reverted to 'enabled' - when I selected discrete in the app it crashed my macbook again, but slightly differently from before in that I got a blue screen (felt like windows again ) rather than a blank powered off one.
Anyway, I have restarted now, and set it again - I'll stick with it for a few days and return with likes/+1/stars etc if it all pans out.
Cheers again. -
Hyper-V teaming cannot failover
I have created two NIC teaming, one for a 147 subnet and one for a 192 subnet,
And used these two teaming in a Hyper-V virtual switch
But when I disable one of the NIC in the 147 team, some VM will loss connection,
It seems to me that the VM originally using the disabled NIC cannot failover to the remaining active NIC.
Anyone have any idea about what might be wrong? Thank you very much.Hi Kevin,
It shouldn't happen , Please try another combination of your physical NICs , such as team members "slot7port1"and "slot7port4" for "external-147" teaming.
Also please try to configure a standby NIC then check if it can failover .
Any further information please feel free to let us know .
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.
Maybe you are looking for
-
I am using Labview 2012 (64 bits) on a Windows 7 OS. The error code is R6031 - Attempt to initalize the CRT more than once. This indicates a bug in your appilcation.
-
RH Linux VIP configuration not working for Oracle 10g RAC installation
Hi all, I am trying to setup my test cluster on Oracle 10gR2 and Red Hat Linux 4. I have the public and private networks working fine and setup. However, after I setup the two VIP addresses, I cannot even ping these two virtual IPs from Linux. CRS in
-
How to retrieve photos that were deleted from trash
I deleted important Jpeg photos from iphoto and then emptied the trash.I have used FileSalvage and Odin software but they have proved ineffective as i have 32,000 + Jpegs in the hard drive.Any recommedations for a program with the ability to preview
-
Wanted: Recommendations for Oracle/Java Web Hosting
I'd like to make some Java/JSTL servlets that access an oracle database. Can someone recommend a hosting service? I'm most familiar with the open source products like JBoss and Jetty and tomcat. Thanks Siegfried
-
I need to run a FORM in PC00_M37_TRM0 transaction. How do I configure this application to run it? tks, Marcos Ferreira