ORA-0907 error when querying XMLDB Table using XMLExists

Hi All,
Get ORA-00907 error when trying to use XMLExists:
SELECT *
FROM tnmab_agreement_xml_binary A
WHERE
( XMLExists('declare default element namespace "http://com.oocl.schema.tnm.agreementbuilder"; $XML/Agreement/ShippingPartyGroups/ShippingParties/CustomerHolder[SAP_ID="$ARG"]')
passing agreements.AGREEMENT_XML as "XML", '5000003001' as "ARG")
OR
( XMLExists('declare default element namespace "http://com.oocl.schema.tnm.agreementbuilder"; $XML/Agreement/NamedCustomerGroups/NamedCustomer/SAP_IDs/StringWrappers[Value="$ARG"]')
passing agreements.AGREEMENT_XML as "XML", '5000003001' as "ARG")
ORA-00907: missing right parenthesis
*00907. 00000 - "missing right parenthesis"*
**Cause:*
**Action:*
Error at Line: 6 Column: 176
Any help is appreciated
Thanks
Auro

XMLExists('declare default element namespace "http://com.oocl.schema.tnm.agreementbuilder"; $XML/Agreement/ShippingPartyGroups/ShippingParties/CustomerHolder[SAP_ID="$ARG"]'
passing agreements.AGREEMENT_XML as "XML", '5000003001' as "ARG")no ')' after the closing quote

Similar Messages

ORA-00054 error when loading Oracle table using Data Services

Hello,
we are facing ORA-00054 error when loading Oracle table using BO Data services
(Oracle 10g database, BODS Xi 3.2 SP3)
Test Job performs
1- truncate table
2- load table (tested in standard and bulk load modes)
Scenario when issue happens is:
1- Run loading Job
2- Job end in error for any Oracle data base error
3- When re-running the same Job, Job fails with following error
ORA-00054: resource busy and acquire with NOWAIT specified
It seems after first failure, Oracle session for loading the table stays active and locks the table.
To be able to rerun the Job, we are forced need to kill Oracle session manually to be able to run the Job again.
Expected behaviour would be : on error rollback modifications made on table and BODS stops Oracle session in a clean way.
Can somebody tell me / or point me to any BODS best practice about Oracle error handling to prevent such case?
Thanks in advance
Paul-Marie

the ora-0054 can occure depending how the job failed before. If this occures you will need the DBA to release the lock on the table in question
Or
AL_Engine.exe on The server it creates the Lock. Need to Kill Them. Or stop it..
This Problem Occurs when we select The Bulkloading Option in orclae We also faced the same issue,Our admin has Killed the session. Then everything alright.

ORA -12569 error when querying dba_change_notification_regs table

Hi,
I am getting ORA-12569 error when i am trying to execute Select * from dba_change_notification_regs from sys user .we are working on oracle 10.2 version.
Please help in resoving the issue.
Thanks In advance.
Priya

ORA-12569:     TNS:packet checksum failure
Cause:      The data received is not the same as the data sent.
Action:      Attempt the transaction again. If the error is persistent, turn on tracing and reexecute the operation.
If this doesn't resolve your issue, please see metalink 4933023.8 (problem fixed there)

ORA-1722 ERROR WHEN SELECTING MFG_LOOKUPS TABLE

제품 : AOL
작성날짜 : 2003-04-07
ORA-1722 ERROR WHEN SELECTING MFG_LOOKUPS TABLE.
================================================
PURPOSE
Problem Description
sqlplus 에서 mfg_lookups table을 select할때,
ORA-1722 Invalid number 에러발생
Workaround
Solution Description
=======================================================
CREATE OR REPLACE VIEW mfg_lookups(
lookup_type,
lookup_code,
meaning,
description,
enabled_flag,
start_date_active,
end_date_active,
created_by,
creation_date,
last_update_date,
last_updated_by,
last_update_login
AS
SELECT lv.lookup_type,
TO_NUMBER(lv.lookup_code) lookup_code, <==== Wrong code!!!
lv.meaning,
lv.description,
lv.enabled_flag,
lv.start_date_active,
lv.end_date_active,
lv.created_by,
lv.creation_date,
lv.last_update_date,
lv.last_updated_by,
lv.last_update_login
FROM fnd_lookup_values lv
WHERE lv.LANGUAGE = USERENV('LANG') AND
lv.view_application_id = 700 AND
lv.security_group_id =
fnd_global.lookup_security_group(lv.lookup_type,
lv.view_application_id)
=================================================================
MFG_LOOKUPS 은 view로 fnd_lookup_values의 lookup_code값을 가지고 오는
방식이나, to_number로 변환하게 되어 있어 숫자가 아닌 문자의 경우
이와 같은 에러를 발생한다.
이번 경우, 고객이 새로 등록한 Lookup code였고, code값을 숫자의 format으로
다시 등록하니 해결됨.
Reference Documents
-------------------

Yes but this is a regular operation and the INSERT is the only opportunity.
BTW, look at what else I have just found:
INSERT INTO Local_Table (a, b)SELECT col1, col2 FROM DUAL INNER JOIN Table1@remote ON (1=1) LEFT JOIN Table2@remote ON (...)
OK.

Error when querying a table through the Query Window

I am running a query on the following table in the ODT Query window - for some reason I get the error below when trying to retrieve the data - I can query the table just fine through SQL Plus - it errors out whether I use grid or text window
ERROR
Arithmetic operation resulted in an overflow.
CREATE TABLE "RF3_PROD_1"."F_EXTRACTMETRICS" ("EXTRACT_NAME" VARCHAR2(50) NOT NULL,"RUN_START_DATE" DATE NOT NULL,"RUN_END_DATE" DATE NOT NULL,"DURATION" NUMBER DEFAULT 0 NOT NULL,"EXTRACT_START_DATE" DATE NULL,"EXTRACT_END_DATE" DATE NULL,"NUM_RECS_ADDED" NUMBER DEFAULT 0 NOT NULL,"NUM_RECS_DELETED" NUMBER DEFAULT 0 NOT NULL,"STATUS" VARCHAR2(50) NOT NULL,"COMMENTS" VARCHAR2(500) NULL) TABLESPACE "EXTRACT_TAB_01_TS" PCTFREE 15 PCTUSED 75 INITRANS 1 MAXTRANS 255 STORAGE ( FREELISTS 1 FREELIST GROUPS 1 INITIAL 8388608 NEXT 516096 MAXEXTENTS 2147483645 MINEXTENTS 1 PCTINCREASE 0 )
I would have formatted it nicer - but that is the way that ODT created it :)

Christian,
I found that this happens when trying to query number fields that are reals with a large decimal value (26 decimal values and above seem to be the magic number). What is strange is that I don't get this problem when I retrieve data from the same table using the Retrieve data option (versus a query for all the data in the Query Window) so they don't seem to be utilizing the same basic code to grab and then display the data interestingly enough (I am sure you knew that). Does this allow you to replicate the issue?
Thanks,
Bryan

Ora-00600 error when dropping a table

Oracle Database 11g Enterprise Edition Release 11.2.0.2.0 - 64bit Production
When I tried to drop a table, I got 600 error:
SQL> desc DEV.ATTR_IDX$EX
Name Null? Type
NODE_ID NOT NULL NUMBER
COL1 NUMBER
SQL> show user;
USER is "DEV"
SQL> select count(*) from DEV.ATTR_IDX$EX;
COUNT(*)
0
SQL> drop table DEV.ATTR_IDX$EX;
drop table DEV.ATTR_IDX$EX
ERROR at line 1:
ORA-00600: internal error code, arguments: [15265], [], [], [], [], [], [], [],
SQL> drop table DEV.ATTR_IDX$EX purge;
drop table DEV.ATTR_IDX$EX purge
ERROR at line 1:
ORA-00600: internal error code, arguments: [15265], [], [], [], [], [], [], [],
I guess this is because it had a parent table, which I dropped (I used "drop table <parent_table>", and it did not give me error, very strange).
SQL> select dbms_metadata.get_ddl('TABLE','ATTR_IDX$EX') from dual;
DBMS_METADATA.GET_DDL('TABLE','ATTR_IDX$EX')
CREATE TABLE "DEV"."ATTR_IDX$EX"
( "NODE_ID" NUMBER NOT NULL ENABLE,
"COL1" NUMBER,
FOREIGN KEY ("NODE_ID")
REFERENCES () ON DELETE CASCADE ENABLE
) PCTFREE 10 PCTUSED 40 INITRANS 1 MAXTRANS 255 NOCOMPRESS LOGGING
STORAGE(INITIAL 65536 NEXT 1048576 MINEXTENTS 1 MAXEXTENTS 2147483645
PCTINCREASE 0 FREELISTS 1 FREELIST GROUPS 1 BUFFER_POOL DEFAULT)
TABLESPACE "USERS"
MONITORING
Try to drop FK constraints yields the same error.
So now how can I drop this table table, any work around?
Thanks.

This is a bug. There is no Patch avaialble for this yet. This error is seen where recyclebin is enabled. Possible workaround is to disable the recyclebin.
This happens with the dictionary corruption due to inconsistency between obj$ and seg$.
This is a correct answer but still i would suggest to contact Oracle support.

ORA-06502: error when inserting into table via db link with long datatype

Folks,
I am getting the following error:
ORA-06502: PL/SQL: numeric or value error: character string buffer too small.
This occurs when an insert is done via a database link into a table that has a LONG data type for one of the columns, and the string contains some carriage returns and or line feeds.
I have checked by removing the db link, and inserting into a local table with identical column data types, where there is no error.
So this might be another db link bug?
So I need to remove the carriage returns and/or line feeds
in my pl/sql block in the page process. I have tried
l_text := REPLACE(l_text, CHR(10), ' ');
l_text := REPLACE(l_text, CHR(13), NULL);
but still getting the ORA-06502. Would really appreciate some advice here, please.
Cheers
KIM

Scott,
Time to 'fess up':
My fault sorry, the error was coming from another page process where I had allowed insufficient string length for one of the variables, and my error message did not identify the page process clearly.
This leads me to make a request for future releases, could the system error messages state which page process caused the problem?
One other thing I notice, and this might be a feature not a fault, the page processes are numbered: "Page Process: 3 of 5". However process 3 is not the 3rd one to be processed, and probably refers to the order in which they are created. Should the number reflect the process order?
Cheers
KIM

(500) Internal Server Error when create storage table use development account

Yesterday, our team suddenly cannot use storage emulator all, it always said 'can not create database' when start the emulator. Finally, we found a issue may affect this, we delete the WAStorageEmulatorDb30.mdf file in C:\Users\[User], and create manully
in localdb, and so we can start the storage emulator later.
But we still can not use it, since it always throw exception when creating Tables/Blobs/Queues, the exception like this:
Microsoft.WindowsAzure.Storage.StorageException was caught
HResult=-2146233088
Message=The remote server returned an error: (500) Internal Server Error.
Source=Microsoft.WindowsAzure.Storage
StackTrace:
at Microsoft.WindowsAzure.Storage.Core.Executor.Executor.ExecuteSync[T](RESTCommand`1 cmd, IRetryPolicy policy, OperationContext operationContext)
at Microsoft.WindowsAzure.Storage.Table.TableOperation.Execute(CloudTableClient client, CloudTable table, TableRequestOptions requestOptions, OperationContext operationContext)
at Microsoft.WindowsAzure.Storage.Table.CloudTable.Exists(Boolean primaryOnly, TableRequestOptions requestOptions, OperationContext operationContext)
at Microsoft.WindowsAzure.Storage.Table.CloudTable.CreateIfNotExists(TableRequestOptions requestOptions, OperationContext operationContext)
at WorkerRole1.TableService..ctor() in c:\Users\<user>\Documents\Visual Studio 2013\Projects\WindowsAzure8\WorkerRole1\TableService.cs:line 21
InnerException: System.Net.WebException
HResult=-2146233079
Message=The remote server returned an error: (500) Internal Server Error.
Source=System
StackTrace:
at System.Net.HttpWebRequest.GetResponse()
at Microsoft.WindowsAzure.Storage.Core.Executor.Executor.ExecuteSync[T](RESTCommand`1 cmd, IRetryPolicy policy, OperationContext operationContext)
InnerException:
And if we visit this url: http://127.0.0.1:10002/devstoreaccount1, it said Internal Error:
<error xmlns="http://schemas.microsoft.com/ado/2007/08/dataservices/metadata">
<code>InternalError</code>
<message xml:lang="en-US">
Server encountered an internal error. Please try again after some time. RequestId:e9637e04-76ad-4237-8df0-31a511e4c116 Time:2014-04-25T00:56:16.9990136Z
</message>
</error>
Any ideas of this? We still don't know what caused this whole trouble from yesterday, is it possible affect the storage emulator just by code? We were coding, not configuring anything. Strange.

I have tried it before, but not works.
Finally, I solved this issue by delete LocalDB instance, uninstall storage emulator and install LocalDB instance / storage emulator again, it works now. Quite strange.

ORA-28513 error when I call sp using dbms_hs_passthrough

I call sp on AS400 using ODBC Database Gateway and dbms_hs_passthrough.
If I make all params IN - all OK. If I set one or more params as INOUT or OUT - I get error message ORA-28513: internal error in heterogeneous remote agent.
declare
ProdID VARCHAR2(6);
DSC VARCHAR2(35);
TCDE VARCHAR2(6);
CLID VARCHAR2(11);
Rate NUMERIC(10,0);
WSID VARCHAR2(4);
ErrorCode VARCHAR2(1);
ErrorMsg VARCHAR2(200);
execStr varchar2(100):= 'call alibts1.ImportInsProductData(?,?,?,?,?,?,?,?)';
i binary_integer;
n binary_integer;
begin
i:=dbms_hs_passthrough.open_cursor@AS400ODBC;
dbms_hs_passthrough.parse@AS400ODBC(i,execStr);
ProdID := '000100';
DSC := 'TEST 1';
TCDE := '000003';
CLID := '001';
Rate := 41;
WSID := 'ORA1';
ErrorCode := ' ';
ErrorMsg := ' ';
dbms_hs_passthrough.bind_variable@AS400ODBC(i,1,ProdID);
dbms_hs_passthrough.bind_variable@AS400ODBC(i,2,DSC);
dbms_hs_passthrough.bind_variable@AS400ODBC(i,3,TCDE);
dbms_hs_passthrough.bind_variable@AS400ODBC(i,4,CLID);
dbms_hs_passthrough.bind_variable@AS400ODBC(i,5,RATE);
dbms_hs_passthrough.bind_variable@AS400ODBC(i,6,WSID);
dbms_hs_passthrough.bind_out_variable@AS400ODBC(i,7,ErrorCode);
dbms_hs_passthrough.bind_out_variable@AS400ODBC(i,8,ErrorMsg);
n:=dbms_hs_passthrough.execute_non_query@AS400ODBC(i);
dbms_hs_passthrough.GET_VALUE@AS400ODBC(i,7,ErrorCode);
dbms_hs_passthrough.close_cursor@AS400ODBC(i);
dbms_output.put_line(ErrorCode);
end;
In trace file I found this:
Exiting WP_SQLBindParameter, rc=0 at 2011/03/14-16:32:21
Exiting hgoprbv, rc=28513 at 2011/03/14-16:32:21 with error ptr FILE:hgoprbv.c LINE:351 ID:Out binds not allowed
nrows:0
Exiting hgoexec, rc=28513 at 2011/03/14-16:32:21 with error ptr FILE:hgoexec.c LINE:182 ID:Calling hgoprbv
Is it mean I can't use OUT params in HS_PASSTHROUGH with ODBC Gateway?

As you've linked the docu - check out
2.3 Known Restrictions
which states:
* Does not support stored procedures
Reason for this restriction is we have no control over the foreign ODBC drivers and the function it has implemented. As you've also already figured out it works for your MS SQL Server connection, but fails for the iSeries which is indicating an issue with the driver or its implementation.
And that's the reason why it is documented as a known restriction and if you want to call a foreign procedure you have to use the dedicated foreign database gateway (if it is available) - for example DG4MSQL for MS SQl Server and DG4DRDA for DB2 databases on IOS, LUW and z/OS.

ORA-00604 ORA-00904 When query partitioned table with partitioned indexes

Got ORA-00604 ORA-00904 When query partitioned table with partitioned indexes in the data warehouse environment.
Query runs fine when query the partitioned table without partitioned indexes.
Here is the query.
SELECT al2.vdc_name, al7.model_series_name, COUNT (DISTINCT (al1.vin)),
al27.accessory_code
FROM vlc.veh_vdc_accessorization_fact al1,
vlc.vdc_dim al2,
vlc.model_attribute_dim al7,
vlc.ppo_list_dim al18,
vlc.ppo_list_indiv_type_dim al23,
vlc.accy_type_dim al27
WHERE ( al2.vdc_id = al1.vdc_location_id
AND al7.model_attribute_id = al1.model_attribute_id
AND al18.mydppolist_id = al1.ppo_list_id
AND al23.mydppolist_id = al18.mydppolist_id
AND al23.mydaccytyp_id = al27.mydaccytyp_id
AND ( al7.model_series_name IN ('SCION TC', 'SCION XA', 'SCION XB')
AND al2.vdc_name IN
('PORT OF BALTIMORE',
'PORT OF JACKSONVILLE - LEXUS',
'PORT OF LONG BEACH',
'PORT OF NEWARK',
'PORT OF PORTLAND'
AND al27.accessory_code IN ('42', '43', '44', '45')
GROUP BY al2.vdc_name, al7.model_series_name, al27.accessory_code

I would recommend that you post this at the following OTN forum:
Database - General
General Database Discussions
and perhaps at:
Oracle Warehouse Builder
Warehouse Builder
The Oracle OLAP forum typically does not cover general data warehousing topics.

Why am I getting an ORA-04052 error when I try to compile a Procedure?

Hi,
The following procedure I'm getting an ORA-04052 error when I try to compile the following procedure.
CREATE OR REPLACE PROCEDURE APPS.Find_String (
pin_referenced_name IN dba_dependencies.referenced_name%TYPE)
IS
cursor cur_get_dependancy
is
SELECT distinct owner, name, type
FROM [email protected]        -- prod.world
WHERE lower(referenced_name) = lower(pin_referenced_name) --'ftbv_salesrep_all_1d'
   AND referenced_type <> 'SYNONYM'
   AND owner <> 'SYS'
order by name;
v_owner varchar2(40);
v_name   varchar2(50);
v_type   varchar2(40);
    BEGIN
       dbms_output.put_line(upper(pin_referenced_name)||' is found in the following objects.');
       dbms_output.put_line(' ');
       dbms_output.put_line(RPAD('OWNER', 30, ' ')||RPAD('NAME', 60, ' ')||RPAD('OBJECT TYPE', 30, ' '));
       dbms_output.put_line('-------------------------------------------------------------------------------------------------------------------');
        FOR i IN cur_get_dependancy
        LOOP
            v_owner := RPAD(i.owner, 30, ' ');
            v_name := RPAD(i.name, 45, ' ');
            v_type := RPAD(i.type, 30, ' ');
            dbms_output.put_line(v_owner ||v_name|| v_type);
        END LOOP;
END find_string;I'm using the link [email protected]. The procedure compiles for other database links used in the cursor including the one commented to the right of the code 'prod.world'.
What's even stranger is that I took the SELECT statement
SELECT distinct owner, name, type
FROM [email protected]        -- prod.world
WHERE lower(referenced_name) = lower(pin_referenced_name) --'ftbv_salesrep_all_1d'
   AND referenced_type <> 'SYNONYM'
   AND owner <> 'SYS'
order by name;out of the procedure and ran it on the command line using the @pinp.world link, the SQL statement ran just fine. But when I tried to compile the above procedure with that exact same SQL statement with the exact same link I get the following string of errors.
ORA-04052: error occurred when looking up remote object [email protected]
ORA-00604: error occurred at recursive SQL level 1
ORA-02068: following severe error from PINP
ORA-03113: end-of-file on communication channelHow can the link work just fine in a regular SQL statement but then cause an error when its compiled in code that otherwise compile just fine when using any other link or even just a plain database. Does anyone have any suggestions?

OK Justin,
Here's the query by itself run in another database using the @pinp.world link and querying the dba_dependencies table in the pinp.world database. As you can see the query using this link works just fine returning the requested rows. I can't figure out why the compiler is having an issue with essentially this same query when I try to compile it in a cursor in TOAD. Also this is the database (dev1.world) that I'm trying to compile this Procedure in.
By the way I'm in an Oracle 9.2.0.6 database and TOAD v9.2.
SQL> conn apps/apps1@dev1
Connected.
SQL> SELECT distinct owner, name, type
2    FROM [email protected]
3   WHERE lower(referenced_name) = lower('ALL_USERS')
4     AND referenced_type <> 'SYNONYM'
5     AND owner <> 'SYS'
6   order by name;
OWNER                          NAME                           TYPE
PUBLIC                         ALL_USERS                      SYNONYM
XDB                            DBMS_XDBUTIL_INT               PACKAGE BODY
XDB                            DBMS_XDBZ0                     PACKAGE BODY
SYSTEM                         MVIEW_EVALUATIONS              VIEW
SYSTEM                         MVIEW_EXCEPTIONS               VIEW
SYSTEM                         MVIEW_FILTER                   VIEW
SYSTEM                         MVIEW_LOG                      VIEW
SYSTEM                         MVIEW_RECOMMENDATIONS          VIEW
SYSTEM                         MVIEW_WORKLOAD                 VIEW
ORASSO                         WWCTX_API                      PACKAGE BODY
PORTAL                         WWCTX_API                      PACKAGE BODY
ORASSO                         WWEXP_UTL                      PACKAGE BODY
PORTAL                         WWEXP_UTL                      PACKAGE BODY
PORTAL                         WWPOB_API_PAGE                 PACKAGE BODY
PORTAL                         WWPOF                          PACKAGE BODY
ORASSO                         WWPRO_PROVIDER_VALIDATION      PACKAGE BODY
PORTAL                         WWPRO_PROVIDER_VALIDATION      PACKAGE BODY
PORTAL                         WWSBR_EDIT_ATTRIBUTE           PACKAGE BODY
PORTAL                         WWSBR_FOLDER_PORTLET           PACKAGE BODY
PORTAL                         WWSBR_USER_PAGES_PORTLET       PACKAGE BODY
ORASSO                         WWUTL_API_PARSE                PACKAGE BODY
OWNER                          NAME                           TYPE
PORTAL                         WWUTL_API_PARSE                PACKAGE BODY
PORTAL                         WWUTL_EXPORT_IMPORT_LOV        PACKAGE BODY
ORASSO                         WWUTL_LOV                      PACKAGE BODY
PORTAL                         WWUTL_LOV                      PACKAGE BODY
PORTAL                         WWV_CONTEXT                    PACKAGE BODY
PORTAL                         WWV_CONTEXT_UTIL               PACKAGE BODY
PORTAL                         WWV_DDL                        PACKAGE BODY
PORTAL                         WWV_GENERATE_UTL               PACKAGE BODY
PORTAL                         WWV_GLOBAL                     PACKAGE
PORTAL                         WWV_MONITOR_DATABASE           PACKAGE BODY
PORTAL                         WWV_PARSE_AS_SPECIFIC_USER     PACKAGE BODY
PORTAL                         WWV_PARSE_AS_USER              PACKAGE BODY
PORTAL                         WWV_SYS_DML                    PACKAGE BODY
PORTAL                         WWV_SYS_RENDER_HIERARCHY       PACKAGE BODY
PORTAL                         WWV_THINGSAVE                  PACKAGE BODY
PORTAL                         WWV_UTIL                       PACKAGE BODY
PORTAL                         WWV_UTLVALID                   PACKAGE BODY
38 rows selected.
SQL>Let me know what you think.
Thanks again.

ORA-03115 error when calling a Stored Procedure

Hi All,
I'm in the process of porting a Pro/C app from NT to Linux. I've installed 8.1.5 on our Linux box and patched it up to 8.1.5.02.
It all kind of works ok, except that I'm sometimes getting ORA-03115 errors when the app calls a stored procedure. The call in question looks like this:
EXEC SQL BEGIN DECLARE SECTION;
VARCHAR resprows[50][3998];
int numret = 0;
int numrows= 50;
int done= 0;
unsigned long resp_id = 0;
EXEC SQL END DECLARE SECTION;
EXEC SQL AT DB_NAME EXECUTE
BEGIN pkg_something.getdata(
:resp_id, /* IN */
:numrows, /* IN */
:done, /* OUT */
:resprows, /* OUT */
:numret /* OUT */
END;
END-EXEC;
The stored procedure basically uses the resp_id value to select rows from a table;
in each row there is a VARCHAR2(4000) column which it copies into the hostarray resprows.
There may be anything from 1 to numrows returned from the SP.
Initially, the resprows rows were defined to be size [4000]. Unfortunately, this caused ORA-02005 errors - I then changed the size to [3998], which seemed to fix the 02005's (although I'm unclear as to the reasons why).
Now I'm getting the 03115 errors when calling the SP. The oracle manual is not very helpful on what this error means.
This all works chipper on NT.
Any ideas?
Thanks in advance,
Nigel.
PS: The database the app is talking to is still hosted on NT.
null

Histon FTM wrote:
ORA-04063: package body "LAZARUS.LAZARUS" has errors Above, obviously conflicts with the statement that follows:
>
The procedure and package have both compiled without errors and the statement on its own works fine in SQL*Plus.I suggest you take a look in the USER_ERRORS view to see, what the errors are.
And just checking:
You have schema called LAZARUS, which holds a package named LAZARUS, which holds a procedure called POPULATEGRIDPOSITIONS?
Edited by: Toon Koppelaars on Oct 1, 2009 5:55 PM

ORA-22813 error when deleting spatial objects in LIVE

Hi,
We are getting an ORA-22813 error when attempting to delete a spatial object from a version-enabled table in workspace LIVE. The spatial object to be removed has a SDO type of multipolygon. The geometry information consists of 4 rings with a combined ordinate count of 4120. The statement used to delete the row is:
delete from tableA where tableA.id in (select tableA.id from tableA where tableA.id = 3);
The error occurs only on a 10g R1 Oracle instance (10.1.0.5.0) with Workspace Manager version 10.1.0.7.1. The delete operation succeeds without problems on a 10g R2 (10.2.0.2.0) instance with Workspace Manager version 10.2.0.3.1. The statement is also executed successfully on the 10g R1 instance if the table is not version-enabled.
Any help on this would be appreciated.
Thanks

Hi,
I would recommend filing a TAR in this one. The only ora-22813 error involving workspace manager and geometry columns that I know about involves queries that need to sort data for which the size of the geometry column was >30k. Does the execution plan for the delete statement involve any kind of sort? However, this is an old 9.2 bug, that I believe was fixed for all 10.1 and newer releases.
Does the same error happen if you do not use the subquery?
Regards,
Ben

Ora 12154 error when trying to add a database to VS Server Explorer

Hi Everyone,
I get the Ora 12154 error when trying to add a database to VS Server Explorer.
How do I get around this problem.
The database service is running and I can connect to the database with pl/sql.
I can also tnsping the database and that is also ok.
Looks like a problem with the odp.net software.
I am running the 32 bit Oracle 11g on a Windows7 Home Premium 64 bit PC.
I am new to this stuff so please help me step by step.
Thanks.
Emad

Hi J. B.
I have a question related to this. After you told me about the //host:1521/database alias I tried it in a VB 2008 program and it worked and returned data. At least I know that it can be used in a VB program without issues. I just now need to be able to add a connection with the Server Explorer.
Anyway here is the VB coding I used. I'm new to this and still learning:
Imports Oracle.DataAccess.Client ' Visual Basic ODP.NET Oracle managed provider
Public Class Form1
' String to connect to the database.
Dim strConnectionString As String = _
"Data Source=//emad-pc:1521/emadeva;User ID=scott;Password=tiger;" '
' Associate the connection string with a connection object.
Dim objOracleConnection As New OracleConnection(strConnectionString)
' SQL query for returning data rows.
Dim strSqlQuery As String = _
"Select dname, deptno " & _
"From dept " & _
"Where deptno = 10" '
' Command object to make this query work.
Dim objOracleCommand As New OracleCommand(strSqlQuery, objOracleConnection)
Private Sub Form1_Load(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles MyBase.Load
' Identify what type of command is being used.
objOracleCommand.CommandType = CommandType.Text
Try
objOracleConnection.Open()
' Set up a Data Reader and load it with data.
Dim objOracleDataReader As OracleDataReader = _
objOracleCommand.ExecuteReader()
objOracleDataReader.Read()
' Convert the department number to a string.
lblDepartmentNumberFromOracle.Text = _
CStr(objOracleDataReader.Item("deptno"))
Catch ex As Exception
MessageBox.Show(ex.Message, "Error")
End Try
End Sub
End Class
I still want to thank you for the help you are providing.
Truly,
Emad

Error ODS activation - sql error when accessing a table.

Hi,
sometimes occurs an error by activation ODS. I have proces chain and when is loaded second packet an error occurs. In monitor>>
-RSMPC 128, datapacket 3 is wrong, with status number 9
-RSMPC 131
-RSDRO 108 - communcation error (sql error when accessing a table)
In sm21>
-sql error when accessing a table
-The exception, which is assigned to the class 'CX_SY_OPEN_SQL_DB', was
either                                                      caught nor passed along using a RAISING clause, in the procedure <b>"UPDATE_ATAB"</b>   "(FORM)"
Since the caller of the procedure could not have expected this exception
   to occur, the running program was terminated.
The reason for the exception is:
The database system recognized that your last operation on the database
would have led to a deadlock.
Therefore, your transaction was rolled back
to avoid this.
ORACLE always terminates any transaction that would result in deadlock.
The other transactions involved in this potential deadlock
are not affected by the termination.
I have BW 3.5.
Thank You very much.

There are a few different scenarios that I can think of where this might come up that all involve what might resulting in parallel (concurrent)processes:
Loading packets in parallel - that is there are X number of processes loading packets concurrently. This could be set in your IMG settings system wide or in the InfoPackage for just this datasource.   You seem to indicate that you don't have this.
Database parallel processing - RSAMDIN - ORA_PARALLEL_DEGREE ( there was a different RSADMIN parm for older versions - forget what SP the change came with).
You have multiple InfoPackages for the datasource, each loading what should be a different range of data, and they run atthe same time.
You could be loading from two different datasources to the ODS at the same time.
If any of these are true, I would look at bumping the INITRANS setting up. Your DBA will probably need to do this for table and its indices. There is a Note - 831234 that allows you to create a parameter in RSADMIN that will specify a INITRANS value (e.g. 20) rather than using the default. The ODS would need to be activated to pick this new setting up for the table to be altered.
You could also look at the Processing settings for the InfoPackage and change to PSA first, then target to see if that helps.
Or if you are loading from two different datasources at the same time, you might adjust your schedule so that doesn't happen.
Pizzaman

ORA-0907 error when querying XMLDB Table using XMLExists

Similar Messages

Maybe you are looking for