Oracle9i installation on Sun cluster not showing the cluster config screen
Hi All,
We are trying to install Oracle 9i RAC on a 2 node Sun cluster. The oracle installer never shows up the cluster configuration screen. However if we run the preInstall checker script from oracle (Installprecheck.sh) , it reports that it has indeed detected the cluster. Can anyone please help us out of this predicament.
-Kishore
Hi Kishore,
I 'm assuming the following:
. Sun Cluster 3.1 will be used to support Oracle 9i RAC
. Oracle is being installed on a file system instead of raw devices
To answer your question, a clustered file system must be present in order for Oracle 9i RAC Installer to recognize that a cluster exists before it displays the cluster configuration screen at the beginning of the installation.
Prior to QFS 4.2, Sun did not support a clusteed file system. All Oracle RAC systems for Solaris were raw device based. You're in luck now because Sun has released Sun QFS 4.2 which support a clustered file system.
Similar Messages
-
11gr1 DB console not showing the cluster instances
Hi All,
11.1.0.7 DB with DB console deployed.
1). EM upload agent command works but on DB console, I am not able to see the cluster instances...
any config file I need to review?
I don't see any errors....the emctl dbconsole commands all work fine.Hi,
Run the following command to check if the cluster instances have been discovered:
<Database Home>/bin/emctl config agent listtargets
If necessary, see Support note 578011.1 for instructions on using emca to add an instance to DB control.
Regards,
- Loc -
Privilege command: the show run does not show the running-config
Hi,
Whenever I login using "user1" I can successfully authenticate however when I ussue the show run for user1. The only thing that I can see are the following:
R4#show run
Building configuration...
Current configuration : 13 bytes
end
R4#
I have put the command on the router as follows:
~~~~~~~~~~~~~~~~~~~~~
aaa new-model
aaa authentication login ACS group tacacs+ local
aaa authentication login NO-AUTH none
aaa authorization exec ACS group tacacs+ local
aaa authorization exec NO-AUTH none
aaa authorization commands 1 ACS-1 group tacacs+ local
aaa authorization commands 1 NO-AUTH none
aaa authorization commands 10 ACS-10 group tacacs+ local
aaa authorization commands 10 NO-AUTH none
aaa authorization commands 15 ACS-15 group tacacs+ local
aaa authorization commands 15 NO-AUTH none
username user2 privilege 15 password xxx
username user1 privilege 10 password xxx
tacacs-server host 10.50.31.6
tacacs-server directed-request
tacacs-server key xxx
privilege exec level 15 show
privilege exec level 10 show running-config
line con 0
exec-timeout 1000 0
authorization commands 1 NO-AUTH
authorization commands 10 NO-AUTH
authorization commands 15 NO-AUTH
authorization exec NO-AUTH
login authentication NO-AUTH
line aux 0
authorization commands 1 NO-AUTH
authorization commands 10 NO-AUTH
authorization commands 15 NO-AUTH
authorization exec NO-AUTH
login authentication NO-AUTH
line vty 0 4
authorization commands 1 ACS-1
authorization commands 10 ACS-10
authorization commands 15 ACS-15
authorization exec ACS
login authentication ACS
end
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Regards,
LorenzLorenz
I believe that the answer is that in implementing privilege levels Cisco designed the show run command so that if you do not have capability to change something that it will not show up in the show run. I believe the logic is that from a security standpoint if you are not authorized to change it you should not be able to see it in the config. So in your case if user1 is not able to change anything then they will not be able to see anything in show run.
HTH
Rick -
forumnotifier
I forgot to ention I upgraded to windows 8.1bigredden
What is the video card/graphics card that your computer uses? If it is NVIDIA GeForce, you are probably involved with the Premiere
Elements 10/NVIDIA GeForce issue which forces the user to roll back the driver version to about May 2013. Since your computer
operating system is Windows 8.1 (assumed 64 bit), there may not be a NVIDIA GeForce driver version that goes back to May 2013
for your computer operating system.
Please let us know the name of your computer's video card/graphics card. If you have a card other than NVIDIA GeForce, then
we can explore other troubleshooting strategy to resolve you issue.
Please read the Announcement at the top of this forum that details the issue and describes the how to resolve with the driver
roll back (if possible). The following is a copy/paste of that Announcement for your convenience.
Premiere Elements 10 NVIDIA Video Card Driver Roll Back
If you are a Premiere Elements 10 user whose Windows computer uses a NVIDIA GeForce video card and you are
experiencing Premiere Elements 10 display and/or unexplained program behavior, then your first line of troubleshooting
needs to be rolling back the video card driver version instead of assuring that it is up to date.
Since October 2013 to the present, there have been a growing number of reports about display and unexplained workflow
glitches specific to the Premiere Elements 10 user whose Windows computer has a NVIDIA GeForce video card. If this
applies to you, then the “user to user” remedy is to roll back the NVIDIA GeForce video card driver as far as is necessary
to get rid of the problems. The typical driver roll back has gone back as far as March – July 2013 in order to get a working
Premiere Elements 10. Neither NVIDIA nor Adobe has taken any corrective action in this regard to date, and none is
expected moving forward.
Since October 2013, the following thread has tried to keep up with the Premiere Elements 10
NVIDIA reports http://forums.adobe.com/thread/1317675
Older NVIDIA GeForce drivers can be found
http://www.nvidia.com/Download/Find.aspx?lang=en-us
A February 2014 overview of the situation as well as how to use the older NVIDIA GeForce drivers for the driverroll back
can be found http://atr935.blogspot.com/2014/02/pe10-nvidia-video-card-roll-back.html
We will be watching for your follow up.
Thank you.
ATR -
Installer is not showing the correct Nodes in RAC
Hi Experts,
We are in the process of upgrade oracle database from 9.2.0.3 to 9.2.0.8 in RAC. While installing the 9.2.0.8 patch set it is not showing the correct database nodes, instead of it showing production database nodes, but we are doing doing it in test machine.
Test Machine hostname:
db1
db2
Prod machine hostname
prod1
prod2
it showing the prod1 and prod2 only.
please suggest us to solve this
Note:
We copy the oracle_home from prod to test for test database cloning.
Thanks
R.SundaravelThen it is highly likely your RAC cluster is not correctly configured.
Open an SR at metalink as the Cluster Verify tool does not exist for your old version. -
I have installed a new drive on my mac book and more ram but the snow leopard install asks which to install the system on but then does not show the drive.
do I have to partition it and name it first. -- if so just one partition?Do this:
Drive Preparation
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
When formatting has completed quit DU and return to the installer. Complete the OS X installation. -
My creative cloud desktop app does not show the programmes installed
My creative cloud desktop app does not show the programmes installed so I cant update lightroom or any other programme, have unistalled and reinstalled but no change
Hi Roni-
If you updated the desktop installer and the screen is blank: try this:
Rename the opm.db file.
Close the Creative Cloud application if it's running.
Navigate to the OOBE folder.
Windows: [System drive]:\Users\[username]\AppData\Local\Adobe\OOBE
Mac OS: /User/<username>/Library/Application Support/Adobe/OOBE folder
Rename the opm.db file to opm_old.db
Launch Creative Cloud
(help finding hidden files on mac:http://helpx.adobe.com/x-productkb/global/access-hidden-user-library-files.html.) -
Upon launch of Lightroom after initial installation a warning came up that said lightroom needs to create temporary files and cant open. Then it opened and the catalog i imported will not show the images. How can I give permission? Running windows 8.1 64 bit. I have avast virus software.
Upon launch of Lightroom after initial installation a warning came up that said lightroom needs to create temporary files and cant open. Then it opened and the catalog i imported will not show the images. How can I give permission? Running windows 8.1 64 bit. I have avast virus software.
-
My gen 4 ipod shuffle is not showing the green light when I switch it on (Green area shown). But when I plug it into the computer there initial orange blink and then solid orange. What wrong with it and how can I fix it.
Hello Korawees,
I was researching the issue you are describing and had a recommendation. The device is very simple, so the software troubleshooting for it is pretty limitted so I think you shoud restore the iPod shuffle and re sync the content. That way, if it is a software issue, this will fix it. Here is the article named Restoring iPod shuffle to factory settings found here: http://support.apple.com/kb/HT1481.
Before Starting
It is important to understand the difference between "update" and "restore." Update does not affect your settings or songs, it simply installs updated software that controls iPod shuffle. Restore erases the disk and restores iPod shuffle to its original factory condition with updated software. If you only need to update iPod shuffle, this should be done on the computer where music is normally synced. Updating on another computer will result in all songs being removed from iPod shuffle.
Warning: Because Restore erases all songs and files on iPod shuffle, make sure to back up any files you've saved on iPod shuffle. Your songs, podcasts, and audiobooks can be synced back to your iPod shuffle if the items are part of your iTunes library.
How to restore iPod shuffle
Ensure that you have an active Internet connection as new versions of iTunes and iPod Software may need to be downloaded to your computer.
Download and install the latest version of iTunes if you do not already have it installed.
Open iTunes, and then connect iPod shuffle to your computer.
After a few moments, iPod shuffle will appear in the Devices section on the left side of the Tunes window.
Select iPod shuffle under Devices and you will see information about it appear in the main iTunes window under the Summary tab/button for iPod shuffle (3rd and 4th generation) or the Settings tab/button for iPod shuffle (1st or 2nd generation).
The Version section tells you whether iPod shuffle is up to date or needs a newer version of the software.
Click the Restore button. You will be presented with one or more restore options that may prompt iTunes to automatically download the latest iPod Software. The 4-possible restore options are:
Restore Option 1: Restore - Restores with same iPod Software version already on iPod.
Restore Option 2: Use Same Version - Restores with same iPod Software version already on iPod even though a newer version is available.
Restore Option 3: Use Newest Version - Restores with the latest iPod Software currently on your computer.
Restore Option 4: Restore and Update - Restores after downloading the latest iPod Software on your computer.
If you are using a Mac, a message will appear prompting you to enter an administrator’s name and password.
A progress indicator will appear on the computer screen indicating that the restore process has started. Do not disconnect iPod shuffle during the restore process.
After the restore process is complete, the iPod shuffle's status light will flash orange continuously. The iPod Setup Assistant window will appear asking you to name your iPod and choose your syncing preferences as you did when you connected your iPod shuffle for the first time.
When you come to step 7, I recommend Restore Option 4.
Take care,
Sterling -
I tried installing an update to QuickTime. An error occurred and it wouldn't install. I tried removing the QuickTime program, but a window appeared telling me that a fatal error ccurred during installation and I could not remove the program. Now what?
I tried removing the QuickTime program, but a window appeared telling me that a fatal error ccurred during installation and I could not remove the program.
I think we'd better see if some other application (other than QuickTime itself) has dropped old QuickTime componentry in the system files on the PC. (If there's a version mismatch between the old componentry and the "QuickTime proper" componentry, that can create those symptoms.)
So we'll go looking for the older QuickTime componentry in the most common locations for it to be stashed.
First we'll need to change some view options on the PC.
1. Open My Computer from the desktop or Start menu.
2. In the Tools menu, click Folder Options.
3. Click the View tab.
4. In the "Advanced settings" pane under "Hidden files and folders" make sure that the "Show hidden files and folders" option is selected, and the "Hide extensions for known file types" option is unchecked.
5. Click OK.
Now in My Computer, open your C drive.
Open the "Windows" folder.
Open the "system32" folder.
What files and/or folders can you see in there with QuickTime in the file/folder name? (In a standard installation of QuickTime, you should see precisely two files ... QuickTime.qts and QuickTimeVR.qtx ... and no QuickTime folders whatsoever.) -
Not showing the Data in VC application
Hi I have developed the application in VC.
It is showing the data some times , it is not showing the data. Can u please let me know what is the problem.
when i checked using the Test Data service . It is showing the data. Then i have developed step by step, in between the time i use to run the application , it was showing the data. finally i have assigned to some role and user id. then also it is showing the data.
Next day after i run the application , it is not showing the data. displaying the message .
"No Data Found".
But when i run the BAPI at the back end R/3 it is giving the data properly.
Can u tell me what might be the problem
REgards
VijayHi Krishna,
check the logs in the NWA. It seems that your connection is broken down sometimes, maybe a timeout. How many records does your data service return?
Check it with external debugging of the BAPI, when you can reconstruct the error.
Best Regards,
Marcel -
Field Explorer in Crystal Reports does not show the same names as Bex Query
Hi
I have crystal reports, I can retrieve data from BW Bex Query. But in the field explorer it does not show the names as in the Bex query designer.
In the Bex query designer a field will have the following technical name 0Debitor and the description is Customer.
It shows in crystal reports in the field explorer twice as D[0DEBITOR]D and D[0DEBITOR]D. It also does not seperate key figures and characteristics.
I would like it to display the field explorer as shown in this blog.
/people/ingo.hilgefort/blog/2008/02/19/businessobjects-and-sap-part-2
Thanks in advanceHi,
take a look here:
/people/ingo.hilgefort/blog/2008/02/19/businessobjects-and-sap-part-2
make sure you are using the MDX Driver and what happens is that you will see several fields per characteristic. example: one for the key, one for the description, several if modelled for the display attributes
Ingo -
I lost my iphone and my macbook pro does not show the icloud in system pref. how do i get icloud on my mac?
iCloud is only available in Lion, 10.7. You will have to upgrade to Lion in order to get into iCloud. If you transfered a .mac or .me address to iCloud through mobile me, or you have another device iCloud enabled, then you can log into the iCloud.com website.
-
Why this query does not show the result?
Why the query with the schema prefixed does not show the result and the query without schema display the correct results?
SQL> select data_object_id,object_type from dba_objects where object_name='HR'.'JOBS';
select data_object_id,object_type from dba_objects where object_name='HR'.'JOBS'
ERROR at line 1:
ORA-00933: SQL command not properly ended
SQL> select data_object_id,object_type from dba_objects where object_name='HR.JOBS';
no rows selected
SQL> select data_object_id, OWNER, object_type from dba_objects where object_name='JOBS';
DATA_OBJECT_ID OWNER OBJECT_TYPE
69662 HR TABLE
OE SYNONYM
SQL> SELECT USER FROM DUAL;
USER
SYSHi,
the column object_name refers to a object_name which is 'JOBS', the column owner refers to the owner 'HR', the value isn't stored together, so you have to select the two columns. It is the same behaviour as every other table/view. Have a look at the values in the view DBA_OBJECTS.
Herald ten Dam
Superconsult.nl -
Report does not show the main section while calling from forms 6i
Hi
I am running report from report from forms 6i but is does not show the data in main section, where as the data in the header section is ok.
But when i run the same report independantly from report builder it show the both header and main section with relevent data.
pl solve the matter
thanks in advancecan you tell me more about this, you might check if you are using different users when you call this report or if the user has all privileges to see all tables in this report
Maybe you are looking for
-
Iphone 4 does not sync video's
i have an iphone 4 16gb ios 6.1.3 and i downloaded some new video's from youtube on my pc. with dvd videosoft. and automaticly (as always) itunes opened and they where in my libary. so i created a new playlist for these video's and i started synchron
-
1. how Do I solve this issue. 2. How do I ensure that i do not lose my playlists along with the songs. 3. What is the procedure needed to be followed.
-
I lecture for a living. My old G4 connected to LCD projector worked great; image displayed on computer monitor is same as that projected by LCD. However my new MacBookPro connected to the LCD projector displays washed out images, as if I designed my
-
Error occurred in deployment step 'Install app for SharePoint': Das Querladen von Apps ist auf dieser Website nicht aktiviert. I am new to sharepoint app development. When i am trying to deploy my developed app in sharepoint i am getting the above er
-
Is there anyway to make the 'Check Spelling as You Type' under Edit always stay on? Seems that I lose it when I fully quit Safari. Help!