OSR 10.3 server drops into ADMIN mode

Using WL 10.3, jrockit_160_05 on RH on a 2 node cluster with the registry.war deployed to a single server within the cluster.
The server running Oracle Service Registry application will drop into ADMIN mode, but not much is logged in the server log. There were no entries in the log for over an hour prior to the server dropping out of RUNNING status, and no one is logged in ( "no active sessions" )
<May 26, 2009 11:20:26 AM EDT> <Warning> <Socket> <BEA-000450> <Socket 12 internal data record unavailable (probable closure due idle timeout), event received 17>
<May 26, 2009 1:08:05 PM EDT> <Alert> <WebLogicServer> <BEA-000396> <Server lock has been requested by <WLS Kernel>>
<May 26, 2009 1:08:05 PM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to SUSPENDING>
<May 26, 2009 1:08:05 PM EDT> <Notice> <HTTP> <BEA-101278> <There are no active sessions. The Web service is ready to suspend.>
<May 26, 2009 1:08:05 PM EDT> <Notice> <Cluster> <BEA-000163> <Stopping "async" replication service>
<May 26, 2009 1:08:05 PM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to ADMIN>
The server has to be shutdown and restarted and will run for a few days before repeating.
Has anyone seen this behavior?

I second hisaaks and mmeyers opinion.
It is much discussed but documented and widely known (and though often thought to be not necessary) prequisite for OSB clustering. Compared to WLS clustering there some limitations.
You can only have one cluster in a OSB domain, if there is more than one maneged servers you have to put them in a cluster.
Like it or not, the product requires it. IMHO it is acceptable. My guess is that one reason for it are the uniformely distributed queues used within OSB.
IMHO the real problems start, when you think about extending the cluster after creating the domain, then you have to manually set all these queues and distributed queues and JMS modules and everything that gets typically targetted for you by the domain wizzard. Or is there a solution for it yet? (Sorry to hijack your thread).
regards,
Barossa.

Similar Messages

Server stopped in ADMIN mode

Can any body help on this issue
Server is stopped in ADMIN mode and is not coming into RUNNING mode

I got the same thing. The managed Server is in ADMIN mode and the other managed server is running fine.
Both these managed servers are clustered. And the Admin Server is also running.
I resumed it and it says, the server is in an incompatible state.
How to resolve it ???
Thanks in advance

WSM Managed server starts in ADMIN Mode after upgrade to 11.1.1.7

We have just upgraded our 11g SOA Cluster environment from 11.1.1.4 to 11.1.1.7. The issue is after the upgrade, our WSM servers are starting to ADMIN state with following error.
<Sep 25, 2013 7:14:35 AM PDT> <Error> <Deployer> <BEA-149205> <Failed to initialize the application 'DMS Application [Version=11.1.1.1.0]' due to error weblogic.application.ModuleException: Failed to load webapp: 'dms.war'.
weblogic.application.ModuleException: Failed to load webapp: 'dms.war'
Caused By: weblogic.management.DeploymentException: Error: Unresolved Webapp Library references for "ServletContext@381802823[app:DMS Application module:dms.war path:/dms spec-version:2.5 version:11.1.1.1.0]", defined in weblogic.xml [Extension-Name: jstl, Specification-Version: 1.2, Implementation-Version: 1.2, exact-match: false]
at weblogic.servlet.internal.WebAppServletContext.processWebAppLibraries(WebAppServletContext.java:2750)
Our cluster environment has one Admin Server, and two of each OSB, WSM and SOA managed servers. As our WSM servers are not coming up, we are not able to start our SOA servers too.
Thank You

Same issue here :-)), Just playing around with policies configuration, the server was running just fine, I wanted to check if the policies are applicable during runtime even the WSM managed server is down. After restart, it started in ADMIN mode, well the solution is straight. It is exactly telling that the dms application is missing the jstl library reference
<Error> <Deployer> <iwpdcdevsoaa.iwater.ie> <WLS_WSM1> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <bcfaf10ec8fbdfc2:-26d85d29:1429ffae24c:-8000-0000000000000003> <1385663491675> <BEA-149205> <Failed to initialize the application 'DMS Application [Version=11.1.1.1.0]' due to error weblogic.application.ModuleException: Failed to load webapp: 'dms.war'.
weblogic.application.ModuleException: Failed to load webapp: 'dms.war'
        at weblogic.servlet.internal.WebAppModule.prepare(WebAppModule.java:395)
        at weblogic.application.internal.flow.ScopedModuleDriver.prepare(ScopedModuleDriver.java:180)
        at weblogic.application.internal.flow.ModuleListenerInvoker.prepare(ModuleListenerInvoker.java:199)
        at weblogic.application.internal.flow.DeploymentCallbackFlow$1.next(DeploymentCallbackFlow.java:518)
        at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:52)
        at weblogic.application.internal.flow.DeploymentCallbackFlow.prepare(DeploymentCallbackFlow.java:159)
        at weblogic.application.internal.flow.DeploymentCallbackFlow.prepare(DeploymentCallbackFlow.java:47)
        at weblogic.application.internal.BaseDeployment$1.next(BaseDeployment.java:649)
        at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:52)
        at weblogic.application.internal.BaseDeployment.prepare(BaseDeployment.java:191)
        at weblogic.application.internal.SingleModuleDeployment.prepare(SingleModuleDeployment.java:44)
        at weblogic.application.internal.DeploymentStateChecker.prepare(DeploymentStateChecker.java:154)
        at weblogic.deploy.internal.targetserver.AppContainerInvoker.prepare(AppContainerInvoker.java:60)
        at weblogic.deploy.internal.targetserver.AppDeployment.prepare(AppDeployment.java:144)
        at weblogic.management.deploy.internal.DeploymentAdapter$1.doPrepare(DeploymentAdapter.java:40)
        at weblogic.management.deploy.internal.DeploymentAdapter.prepare(DeploymentAdapter.java:191)
        at weblogic.management.deploy.internal.AppTransition$1.transitionApp(AppTransition.java:22)
        at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:261)
        at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:220)
        at weblogic.management.deploy.internal.ConfiguredDeployments.prepare(ConfiguredDeployments.java:166)
        at weblogic.management.deploy.internal.ConfiguredDeployments.deploy(ConfiguredDeployments.java:122)
        at weblogic.management.deploy.internal.DeploymentServerService.resume(DeploymentServerService.java:181)
        at weblogic.management.deploy.internal.DeploymentServerService.start(DeploymentServerService.java:97)
        at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)
        at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)
        at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)
Caused By: weblogic.management.DeploymentException: Error: Unresolved Webapp Library references for "ServletContext@384044243[app:DMS Application module:dms.war path:/dms spec-version:2.5 version:11.1.1.1.0]", defined in weblogic.xml [Extension-Name: jstl, Specification-Version: 1.2, Implementation-Version: 1.2, exact-match: false]
        at weblogic.servlet.internal.WebAppServletContext.processWebAppLibraries(WebAppServletContext.java:2750)
        at weblogic.servlet.internal.WebAppServletContext.<init>(WebAppServletContext.java:416)
        at weblogic.servlet.internal.WebAppServletContext.<init>(WebAppServletContext.java:494)
        at weblogic.servlet.internal.HttpServer.loadWebApp(HttpServer.java:418)
        at weblogic.servlet.internal.WebAppModule.registerWebApp(WebAppModule.java:976)
        at weblogic.servlet.internal.WebAppModule.prepare(WebAppModule.java:384)
        at weblogic.application.internal.flow.ScopedModuleDriver.prepare(ScopedModuleDriver.java:180)
        at weblogic.application.internal.flow.ModuleListenerInvoker.prepare(ModuleListenerInvoker.java:199)
        at weblogic.application.internal.flow.DeploymentCallbackFlow$1.next(DeploymentCallbackFlow.java:518)
        at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:52)
        at weblogic.application.internal.flow.DeploymentCallbackFlow.prepare(DeploymentCallbackFlow.java:159)
        at weblogic.application.internal.flow.DeploymentCallbackFlow.prepare(DeploymentCallbackFlow.java:47)
        at weblogic.application.internal.BaseDeployment$1.next(BaseDeployment.java:649)
        at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:52)
        at weblogic.application.internal.BaseDeployment.prepare(BaseDeployment.java:191)
        at weblogic.application.internal.SingleModuleDeployment.prepare(SingleModuleDeployment.java:44)
        at weblogic.application.internal.DeploymentStateChecker.prepare(DeploymentStateChecker.java:154)
        at weblogic.deploy.internal.targetserver.AppContainerInvoker.prepare(AppContainerInvoker.java:60)
        at weblogic.deploy.internal.targetserver.AppDeployment.prepare(AppDeployment.java:144)
        at weblogic.management.deploy.internal.DeploymentAdapter$1.doPrepare(DeploymentAdapter.java:40)
        at weblogic.management.deploy.internal.DeploymentAdapter.prepare(DeploymentAdapter.java:191)
        at weblogic.management.deploy.internal.AppTransition$1.transitionApp(AppTransition.java:22)
        at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:261)
        at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:220)
        at weblogic.management.deploy.internal.ConfiguredDeployments.prepare(ConfiguredDeployments.java:166)
        at weblogic.management.deploy.internal.ConfiguredDeployments.deploy(ConfiguredDeployments.java:122)
        at weblogic.management.deploy.internal.DeploymentServerService.resume(DeploymentServerService.java:181)
        at weblogic.management.deploy.internal.DeploymentServerService.start(DeploymentServerService.java:97)
        at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)
        at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)
        at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)
>
So search for "jstl" within the weblogic console in search bar, it is type of library, click on it and target it to the managed server where OWSM is running as weel. It was root cause in my case, somehow the library was not targeted to our WLS_WMS1 managed server. Now the server is back in RUNNING mode. Of course apply this in case of problem with SOA servers, target it to the cluster or exact nodes and it should work.
Still I don't know how the issue has been crated, I don't think that somebody removed it from deployment. Rather I think that somebody was applying patch or some artifacts to OSB or SOA managed server and this library was required as well, but as soon as we have separated WSM cluster, it was maybe assuming that it is running within OSB or SOA clusters and therefore didn't target the WSM cluster automatically. But this is just the idea :-))
Ladislav

IdeaPad B590A - dropped into sleep mode when lid was covered and requests a password

Hello, dears! Sorry if I missed the section, I'm a newcomer
I bought my Lenovo IdeaPad B590A with Windows 8 a week ago. Having used it a bit I happened to cover the lid. My notebook turned into the sleep mode. It requests a PASSWORD now, but I have no idea what password?
Thus, now I have 2 screenviews upon Restart: 1) Screen with LENOVO sign and 2) screen with a profile photo (empty), the number " 1" and the line for a password. But I did'n created a password.
Some people recommended that I use Restart and then press F8 button for a 'safety regime' opening for Windows. The problem is the notebook does not show the Windows screen - only Lenovo screen and Rquesting password screen.
Is there any chance to remove this password request so that I could enter finally?
I'd be grateful for any advice,

Hi Ekaterina,
Welcome to Lenovo Community Forums!
I’m sorry to hear that your B590A Laptop is waking up on a Password prompt which you have not created, but let me inform you that without creating the password for the current user account the popup will not be prompted at the startup. As it is displaying password for a Single user, I strongly suggest you to perform OSRI (Operating System Re-Install) using OKR (One Key Recovery) by clicking on OKR button provided in the computer, below is the link to download the User Guide for the steps to perform OSRI and refer page no. 1 to locate the OKR button and page no. 27 for the steps to perform OKR.
NOTE: Please backup the data in the computer before performing OSRI, as the data will be completely erased.
User Guide Lenovo B590
Hope this helps!!!
Do post us back for further queries.
Best Regards
Shiva Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Booting into recovery mode and Web service in 10.7 server

I have two servers: Server A is running 10.6 server and server B is running 10.7 server. Both are on the same LAN at a data center. My questions are as follows:
1 - is there a way to restart server B into recovery mode remotely? (and not using a KVM)
2 - if server B was booted successfully into recovery mode is there a way to screen share with it from server A? If so how would this be done?
3 - can Apple Remote Desktop reboot a 10.7 machine into recovery mode and still continue to see its screen?
4 - in the Server app of 10.7 server there is a default website setup in the Web service. it doesn't seem possible to edit any of the information for this default website, is this true?
5 - is there any way to get the Web service in the 10.7 Server Admin tools? it is missing among many other services.
Thanks

Probability is very high that you have a hardware failure. You should get an external bootable drive (or startup with a bootable DVD if you can) JUST to prove that it's not the motherboard, but probably the hard drive that's failed.

How to stop B2B listener polling when SOA server in Admin Mode

Hi ,
I recently came across this situation like my B2B FTP listener is polling and deleting file when my SOA server is Admin Mode.
Can anyone help me to stop that polling when server is in Admin Mode ?
Thanks,
Saba

thanks for quick reply...
the "catch (IOException e) {... } " block in Server already catches this exception, and as there is no other code but printing the exception, the method run() is quitted (no need to terminate the loop). However, the thread is NOT terminated even after that. To make it sure, I added a public variable and accessed it from Handler at the end of the code, after sd.resetSock(); !!!
You told that it doesn't stop because of the way I coded it, isn't it the traditional way of setting a listener socket? If no, may be recoding the listener would be much better...

How can I select shutdown & close the display w/o going into sleep mode?

I have learned to wait untill the MBP full shuts down before closing the display. In the past I have pressed shutdown closed the display only to find out later the MBP goes into sleep mode before fully shuting down. When I reopen the display the computer finishes the shutdown process or worse the battery is dead.
I would like to select shut down, close the display and walk away while the computer completes the shutdown process.
Is there any setup options or apps. that will allow this?
Thanks, Joe
(new to the mac)
MBP Mac OS X (10.4.6)

Well hello there, and welcome to Macintosh.
Unfortunately you can't change anything to stop this from happening. The shutdwn process goes about its business killing processes and applications that have been running. The sleep process interrupts ALL business going on in the OS, and puts the machine into low power mode, as it is not aware of the nature of the running processes (in this case, the shutdown process), knowing only that they must be slept and the machine dropped into sleep mode. You gotta wait it out before you close the lid.
I would suggest sending a message in OS X feedback requesting this as a feature!
If you find this response helpful or if it solves your issue, please click the appropriate icon in the header of this reply.

Sup720 booting into rommon mode

new sup720 drops into rommon mode. config reg is 2102 and boot system command points to right image located in sup-bootflash:

You might need to upgrade your ROMMON. We did with our brand new Sup720's. Below is the procedure we use. Please pardon the formatting. If you see "invalid ..." after the "show rom slot n sp" you need to load ROMMON code (available from Cisco's downloads). Good luck.
ROM Upgrade (650x)
1 sh rom slot 5 sp Display current ROM settings
2 copy tftp:c6ksup3-rm2.srec.8.4.2 sup-bootflash:c6ksup3-rm2.srec.8.4.2 TFTP the file to the 650x
3 upgrade rom slot 5 sp pref region[1 | 2] Command to switch regions to boot ROMMON from. Upgrade that too or leave at old version.
4 upgr rom slot 5 sp file sup-bootflash:c6ksup3-rm2.srec.8.4.2 Upgrades current preferred ROMMON region
5 repeat step 3 for other region After successfully upgrading to the new version do the other one too.
6 reload Reload (once for each ROMMON region) to test
rommon invalidate F1 Command to invalidate a ROMMON region

IPhone keeps going into recovery mode while playing mp3's through Ford SYNC

Hi There,
I have a 2008 Ford Focus with the SYNC iPod connectivity. I have the latest SYNC software update installed in my car.
Twice now while playing songs via the USB connection with SYNC, my phone has suddenly dropped into recovery mode when it finishes playing a playlist.
Can anyone offer a solution ? It is really annoying having to restore my phone all the time

Ooops sorry about that. It must've been 8.1.2 then? I honestly don't remember.. I wasn't paying attention when I updated since I regularly do it for my iPad, other phones. Anyway, whatever is the latest version of the iOS, it got me stuck in recovery mode.
really sorry about the 8.2 Info

Ios8 ipad sometimes goes into airplane mode

My ipad 2 with 3G capability has taken to dropping into airplane mode without any instruction from me. No obvious pattern.
Have also experienced on some occasions, again no obvious pattern, a message telling me that no wireless network cover was available when I was in an area of excellent phone coverage and my ipad is set to use phone coverage by default if no wireless coverage is available. The display did not indicate any phone coverage however and disabling wireless coverage changed nothing.

Thanks for the input, you are possibly correct. I had not considered that possibility - my reservation is that it has happened on 3 occasions since changing over to ios8 and never prior to that that I can recall. Time will tell. Thanks again.

Aaa authorization (device doesn't always go into enable mode)

When I log into the 4500 switch with my domain account, I get priv 1 only and have to “enable” with the local enable password to get to priv 15. How do I set this up to get directly to enable? The ACS 5.1 is setup with a authorization/shell profile for Priv 15, no problems there.
2821-RTR2#show run | incl aaa
aaa new-model
aaa authentication login default group tacacs+ local enable
aaa authentication login CONSOLE local-case line
aaa authorization exec default group tacacs+ none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common
4500 that drops into enable mode
4500-SW1#show run | incl aaa
aaa new-model
aaa authentication login default group tacacs+ local enable
aaa authentication login CONSOLE local-case line
aaa authorization exec default group tacacs+ none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common

On the non-working device enable:
debug aaa authen
debug aaa author
debug tacacs
and post the results.
Also, on ACS 5.1 review the details for the authen/author on both the working and non-working devices and see if the desired shell profile is picked for the non-working device.

TACACs+ commands not dropping me into enable mode

Hi All,
I've just comfigured the following on a router running IOS 15. All my other devices are running the old tacacs commands but thought I'd try the new CLI version.
It works, e.g get prompted for username/password and authenticates against our AD Server (integrated with ACS4.2). I get into the router but into usermode.
My other devices drop me straight into Priv Mode. Only difference is the the new commands v the old commands but I can't see anything that is different in relation to putting me into Priv mode.
Any ideas?
aaa group server tacacs+ ABC_ACS
server name ABC_TAC
tacacs server ABC_TAC
address ipv4 172.27.10.10
key secretkey
aaa authentication login ACS_List group ABC_ACS line
aaa authorization exec ACS_List group ABC_ACS if-authenticated
aaa accounting exec ACS_List start-stop group ABC_ACS
aaa accounting commands 15 ACS_List start-stop group ABC_ACS
line vty 0 4
password test
authorization exec ACS_List
accounting commands 15 ACS_List
accounting exec ACS_List
login authentication ACS_List
length 0
transport input ssh

Make sure you defined the username with a static privilege level of 15 otherwise it will not be able to pass the enable authentication.
If ACS 5.x or higher go to the policy elements: Shell Profile and make sure you have one assigned for a static maximum privilege of 15 and most important that its applied into a access-policy rule

TS3742 My apple after the startup and holding p+r + control+ option goes to a screen with a locked padlock and a space for me to type I've entered my admin password but nothing seems to happen and it can't get my iMac into safe mode or anything this is al

My iMac at start up goes to the apple logo with the spinning symbol under neath it.
After a while it goes into a screen with a prohibited symbol.
I can't boot it into safe mode or single user mode only thing I can do is press the control, option and p,r keys and that leads me to a locked screen with a bar under neither it for me to type a password or something I've tried my admin password many times and nothing happens
WHAT DO I DO

Sounds like you have a firmware password set.
As you can't do that accidentally, you surely must know the password (which is different from your admin password)?

SCOM 2012 - Use Powershell to put specific server and contained objects into Maintenance Mode

I am still trying to develop what I thought was going to be an easy script, to put a specific server and all it's contained objects into maintenance mode in SCOM 2012.   Not a group, but just one specific server and all it's stuff.
My script to START maintenance mode has two parameters:
1. The FQDN. So for example: server1.contoso.com
2. The amount of minutes to put into maintenance mode
Then it does the following to START maintenance mode:
Import-Module OperationsManager
$Instance = Get-SCOMClassInstance -Name $FQDN
If ($Instance)
$newEnd = ((Get-Date).AddMinutes($minutes))
Start-SCOMMaintenanceMode -Instance $Instance -end $newEnd -Reason "PlannedOther" -Comment "Comments here"
This seems to work from what I can tell. I know that when you schedule maintenance mode manually in SCOM, there is an option to apply to "Selected objects and all their contained objects". I do not know if that is occurring based on
my code above.   But I think that is what I want to happen.   I just want all monitoring and alerting for the specified server to stop.   So if you think I need to change the above code so that it gets all the "contained
objects" please let me know.
The second part, which I know for a fact isn't fully working, is intended to stop maintenance mode for a server.
My script to STOP maintenance mode has only one parameter:
1. The FQDN. So for example: server1.contoso.com
Then it does the following to STOP maintenance mode:
Import-Module OperationsManager
$Instance = Get-SCOMClassInstance -Name $FQDN
If ($Instance)
$MMEntry = Get-SCOMMaintenanceMode -Instance $Instance
If ($MMentry)
#basically sends an end time of 1 minute from when the script is run
$newEnd = ((Get-Date).AddMinutes(1))
Set-SCOMMaintenanceMode -MaintenanceModeEntry $MMEntry -EndTime $NewEnd -Comment "Removing from Maintenance Mode"
This part does seem to work partially.   It does remove the server from maintenance mode. However, I suspect that it's not removing all the "contained objects" from maintenance mode because when I run the script to stop maintenance
mode on a server, the little maintenance mode icon in SCOM does go away but the overall light for the server stays set to "Not Monitored".   It never turns back to the green checkbox and says "Healthy".   When I start
and stop maintenance mode manually I can see that the green Healthy checkbox comes back. But when I try to run my above code to do it via script, it stays at "Not Monitored" instead.
Can someone help me out here? Looking for answers to two questions:
1. Does my Start maintenance mode code look ok? Will that put a server and all it's contained objects into maintenance mode?
2. What do I need to hadd to my Stop maintenance mode code, so that it correctly stops maintenance mode on the server and all its objects and everything starts to be monitored again?
Thanks in advance! Please let me know if you need any more information in order to be able to help me!

Hello, thanks for your response. Unfortunately, it does not appear that the link you provided works.
As far as not including "selected objects and all their contained objects" I am wondering if there is a way for me to tell for sure. One thing I found was that if I run this script and put the server into maintenance mode, then I go into
SCOM and click on Edit Maintenance Mode for that server, it shows me the details.   It has some comment, and my selected reason, based on the code I posted above.   It also DOES have "selected objects and all their contained objects"
selected at top. So it seems to me like it is working correctly, and does contain all the objects.   If you think that 'Edit' screen would be inaccurate for some reason, please let me know. Or if you know of a way for me to check and
confirm, please let me know that as well.
As for REMOVING it from maintenance mode, I did eventually find a line of code that I think works. Here's what my code looks like now:
Import-Module OperationsManager
$Instance = Get-SCOMClassInstance -Name $FQDN
If ($Instance)
$MMEntry = Get-SCOMMaintenanceMode -Instance $Instance If ($MMentry)
$Instance.StopMaintenanceMode([DateTime]::Now.ToUniversalTime(),[Microsoft.EnterpriseManagement.Common.TraversalDepth]::Recursive);
When I use the above code to STOP maintenance mode, the green checkmark does reappear for the server, and everything seems to be being monitored again.   Unlike before, where the maintenance mode icon would go away, but it would never change back
to saying 'Monitored' again. So I think that changing that one line to stop maintenance mode seems to have done the trick.
So I guess my last concern now is just putting in maintenance mode initially, as I was talking about above. If you still think the 'Edit Maintenance Mode' screen is not a good indicator of what my code does, please let me know.

HT201263 i forget my passcode.now when i put my phone into recovery mode it connects to i phone software update server and sftware starts download but after much time of download error=-39 occurs

now when i put my phone into recovery mode it connects to i phone software update server and sftware starts download but after much time of download error=-39 occurs

my itune keep showing message that i tune is downloading software for my phone. but downloading for several minutes it displays message that i tune cannot connect to my phone because it is locked with a passcode. first entre the pass code.
on the other hand phone is started with a message on screen phone is disabled.

OSR 10.3 server drops into ADMIN mode

Similar Messages

Maybe you are looking for