PCI 4351 error 201003

i am trying to read a type k thermocouple signal and have recieved a number of errors when trying to set up a temperature channel
first error is 201003 this occures when attempting to run the channel configuration
second error occures ocational when i run the test panel and it is 10401. the test panel will occasionally work and i can get a temp reading from the device
i have run the diagnostics utillity and received the following message
Error -200220 occurred at an unidentified location
Possible reason(s):
Measurements: Device identifier is invalid.
Please select a DAQmx device from the pull-down menu.
------ DIAGNOSTIC UTILITY ABORTED -----
there are no devices that appear in the pulldown menu
any assistance in this matter would be much appreshiated

Both of those errors indicate that LabVIEW does not recognize the device. I would look over the "Where to Start with Your NI 4350/4351" article to make sure you have set everything up correctly and installed the proper driver software. If you're still having problems with the device, look in Measurement & Automation Explorer to see if you can communicate with the device and set up a simple temperature task. Note that you will have to use the Traditional NI-DAQ driver instead of DAQmx and your O/S (if Windows) is limited to XP and 2000.
Jake H | Applications Engineer | National Instruments

Similar Messages

NI PCI 4351 errors

I have a PCI 4351 thermocouple card and I am trying to use it under Windows XP. The following software was installed on the PC:
Card driver: ni435x_v21 downloaded from National Instruments website
NI-DAQ version 6.9.2f4
NI-PAL version 1.5.5f0
NI-VISA version 2.6.0
Labview 6.1 full version
Measurement an Automation Explorer that came with Labview 6.1
The control panel of the PC shows the card correctly installed and working without conflicts. Measurement and Automation Explorer from NI detects the card too but the card fails the test. The error code 10401 informs me that this is an "unknown device". I tried it with another PC, now using the latest version of NI-DAQ, NI-VISA, and automation explorer but the result was the same
QUESTION
Is it safe to assume that the card is toast? (It was in a drawer for a while, so that is a possibility.)

Hi nizkorod,
Thanks for contacting National Instruments. I understand you are having a problem with your PCI 4351 board. Windows seems to be recognizing it, but the card does not pass the self-test in Measurement and Automation Explorer. This definitely appears to be a hardware problem since this is happening on two separate computers with different versions of NI-DAQ. The PCI-4351 should be working on both computers, with either NI-DAQ 6.9.2 or the latest 7.x. The board isn't completely toast though and can most likely be fixed. If you would like to get this board repaired then please give NI a call at 1-866-275-6964 and we can set up a repair.
Have a great day!
Erick D.
NI Applications Engineer

Thermocouple Measurements on TBX-68T with PCI-4351

I have set up Traditional NIDAQ Virtual Channels for 2 different thermocouples. In a simple program, I wire each channel to AI Sample Channel.vi and get the temperature reading. This works fine. However, when I do this inside of a larger code where I am also reading voltage measurements on my PCI-4351 (using 435xFast.vi which I downloaded), the first thermocouple I read is always giving an erroneous error. Do I have to reset the board in some way before I take the temperature readings?

I've got just a few questions for you:
1. Are you seeing a large negative value anywhere else other than when you run your particular vi as a subvi? Test panels in MAX? Other example programs?
2. Do you have the latest drivers for your application? NI-DMM 2.3.1? NI-DAQ 7.3.1? NI-435x 1.1?
3. Have you tried reseting the board in MAX and then running your application? If this takes care of that first bad sample, you could try calling Reset Device in the Traditional DAQ function palette before starting your acquisition.
Please let me know what you can. Have a great Thanksgiving!
Logan S.

Tecra M9 - PCI Express Error at start-up

Hello Everybody ..
I own a Toshiba Tecra M9 (PTM91E-04R03TEN)
http://www.toshiba.ie/innovation/jsp/supportMyProduct.do?service=IE#tab0;
On switching on,- Its Showing the Toshiba splach screen and then "PCI Express error." on a black screen
I can't get beyond this Black Screen
and I can't get into BIOS ??..
One time it did manage to boot up fully, I left it running for a while as I save information from the HDD. but then the problem started again .
I believe this is a problem with the nvidia GPU ( Fatigue cracking on the BGA )
I have the Laptop stripted down .. and have purchased ArctiClean , Thermal Pad, & Arctic Silver for the "repair"
Should I have somebody scan the hardware and to find the troublemaker ? ..OR.. should I just reflow the GPU .
I'm technically minded .. but not a PC / Laptop technican :(..
any Instruction on how to proceed would be greatfully received ..
Should i just " bung it in the oven" and see how it goes ? :) :) .
Regards,
Peter

Hi
I found and read your other post regarding this issue and in my opinion the PCI Express error is related to an PCI device (i.e miniPCI module like WLan / Bluetooth, etc ) connected to the motherboard.
Of course I cannot say for sure that this issue isnt related to a GPU malfunction.
Usually such details can be provided only by an service engineer who checked the notebooks hardware.
Generally I dont recommend to disassemble the notebook. Its very tricky to perform such procedure and of course there is always a risk of part damage doing such procedure without any instructions.

Windows 7 - Pci-to-Pci Bridge (Error: Code 10) - PCI Video Card

Before I state my issues I will list what I'm running and what I'm trying to accomplish.
I'm running Windows 7 Enterprise 64-bit edition, not the Beta or RC. I have 3 video cards in my possession (listed below).
- (PCIe) Evga GTX260
- (PCI) Evga 9400GT
- (PCI) Evga Fx5500
Out of those 3 cards I only use the GTX260 and the 9400GT. I had to 'retire' the Fx5500 because the latest WHQL (certified) drivers only provide support as far down as the "6 series" Nvidia cards. Unfortunately the Fx5500 is a "5 series" and falls below that line. I have already tried to use the GTX260 and Fx5500 in previous versions of Windows (XP and Vista), but there is no way to download and install two separate drivers for two of the same make of video card - you'll get nothing but errors. There is the option of going to a place like guru3d.com and downloading a custom supported driver that covers both the GTX260 and Fx5500, but the drivers are not certified and lack support. Therefore, I purchased and now use the 9400GT which is covered under the drivers for the GTX260 and eliminates the need for messing around with custom drivers. Also, the 9400GT has a better graphics processor and more memory than the Fx5500, so it was time to upgrade anyway.
Now that you have some background info here is my issue Whenever I install the 9400GT I get a second 'pci-to-pci bridge' entry (the other entry has no errors) that shows up under 'System Devices' in the Device Manager. The second pci-to-pci bridge entry has a yellow triangle with an exclamation mark on it that refers to a problem. When you check the properties of this device it more or less says that Windows has detected a problem (Error Code 10). The GTX260 still works and even shows up under the 'Display Adapters' as a GTX260, but no entry for the 9400GT exists. I have tried the 9400GT in both PCI slots and each time it does the same thing. If I pull out the GTX260 and ONLY run the 9400GT, I still get the pci-to-pci bridge issue, BUT I do get a picture and can boot into Windows 7 without a hitch. When I do this there is still nothing listed under the 'Display Adapters' as a 9400GT or even a VGA compatible device.
After messing around with this for 10 hours (yes, I said 10 hours) I decided to dig out my retired PCI video card (the Fx5500). When I installed this card I had no 2nd pci-to-pci bridge entry appear under 'System Devices', and the one that was listed had no yellow triangle or error codes. I then checked under 'Display Adapters' and Windows 7 had recognized it as a VGA compatible device and was asking for drivers.
I have now concluded that there is definitely no issue with the motherboard or any of my hardware (including video cards). At first EVGA Support and I had suspected that the motherboard may be bad because of all of the pre-diagnostic steps I had taken during my 10 hour ordeal. I'm not going to list everything I did because it would literally take 3 hours to type it all in. Just believe me when I say that I have tried most things including but not limited to the latest bios updates (flashed 4 times and completely reset to ensure accuracy), custom IRQ management, entire OS re-installation X2, multiple/latest chipset drivers installed, multiple/latest video drivers installed, memtest testing, complete hardware teardown and re-build (adding one device at a time), and MUCH more. The only thing I did not try was installing a different OS other than Windows 7 64-bit to see if I could replicate the issue. This is a waste of time though because lets say that I install Windows XP Pro and the 9400GT doesn't have this issue... Well, that's great, but who gives a damn about XP Pro when I have been using it for the last 9 years and when I have a full version of Windows 7 that I want to use? I'm certainly not going to run XP Pro over Windows 7 just to use this PCI video card. Second, if I install XP Pro and it still gives me the same pci-to-pci bridge error then again, I've only wasted more time because if its not going to work in either OS then Im sure as hell not going to leave XP Pro installed when I can use Windows 7.
Thanks,
piyush

Maybe stupid question now but has your posting anything to do with Toshiba and Toshiba notebooks?

Solaris 10 on Sun Ultra 40 --PCI system error on /bus/device/function 0048h

Everytime I boot to Solaris 10 (08/07) I get the following message at the top of my screen:
PCI system error on /bus/device/function 0048h
The system boots up successfully, but I find this error to be particularly annoying. I have no third-party cards plugged into any PCI slot.
Why am I getting this error. Is the BIOS just giving me a bogus error?
Any help would be appreciated.
Thanks.
Robert

Hello,
I even got the same Problem with an Ultra 40. After powering off and on the system during the last 3 days, now i got an error mesage, "CPU3 can not be started"
cleared the CMOS and now i am back on "PCI System Error on Bus/Device/Function 0048h" the system is running with the latest 1.7 Bios update.
First of all I tried to flash the system back to an lower version but the flashsoftware seems not to support this operation have to make own boot media with the flashprogramme and flash by forced the 1.0 or 1.2 version.
regards
Monchichi

Measuring temperature with PCI-4351 & TC-2190

Hi,
I am a new LabView developer. I have a PCI-4351 data logger card and a TC-2190 thermocouple chassis. I cannot communicate with the 4351 cuz I don't know how. I've set up a channel with MAC and the hardware test works okay, but I can't find the right object to grab the measurement when I'm creating the vi. Do I use NI-DAQmx or VI Logger functions to take simple instantaneous temp. measurements?
Is there some example code I can start with? I tried to run the ni_435x_thermocouple.vi example that I downloaded from the developer zone, but there are several sub-vi's not loaded on my machine (eg: AI Hardware Config.vi) that it tries to find upon launch. Looks like a vestiges of LabView 5 that aren't there anymore. Is there an easier way for this LabView 8 user?
Sincerely,
Jack Santori
410-471-6262

Hi Jack,
The PCI-4351 only has support for the Traditional NI-DAQ functions and not NI-DAQmx. It sounds like you don't currently have those drivers installed on the system, and this is why the Traditional NI-DAQ function AI Hardware Config.vi cannot be found.
If you are running Windows 2000 or XP, the most current version of the Traditional DAQ drivers available for download is 7.4.1 and they can be downloaded here. If you are not using one of these operating systems, Traditional DAQ driver versions for another OS can be found here. Example programs are a great place to start, and the Developer Zone includes a wealth of information. Installing the Traditional NI-DAQ drivers will also include example programs that you can open and run in LabVIEW 8.0 by going to Help>Find Examples.
Regards,
Andrew W
National Instruments

Pci device error

After re-installing xp with sp2 im getting pci device error in the ctrl panel and cannot get any sound from my pavilion2020ca. I,ve tried all the drivers in hp site to no avail. Any help would be grateful.

Do you have ZE or DV 2020ca? If you have DV2020 have you installed Microsoft UAA driver?
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

PCI 4351 cjc with SCB-68

Is it possible to enable cold junction compensation using a PCI 4351 board with a SCB-68 terminal block?
I have searched around and tentatively concluded that it is not possible. Under the "accessory" option in MAX SCB-68 is not an option, and TBX-68 does not have a checkbox for temperature compensation.

Hello Craig,
National Instruments recommends the following accessories that are designed to be used with the NI 435x for thermocouples/CJC: the cold-junction sensor is on analog channel 0 on the TC-2190, TBX-68T, and CB-68T accessories. Additionally, the NI TBX-68T (used with NI 435x devices only) is the correct acccesory which includes a built-in cold-junction compensation sensor and autozeroing circuitry (compared to TBX-68).
Best regards,
Ali M
Applications Engineer
National instruments

PCI Express Error - Qosmio G40-10Z

Yesterday i turned on my laptop and i got a black screen with the message "PCI Express Error"
I immediately started searching the web what this error might be and i discovered that it's a known problem with some Toshiba laptops.
http://www.nvidiadefect.com/qosmio-pci-express-error-t383.html
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=49108
http://www.nvidiadefect.com/toshiba-qosmio-g40-12c-t1149.html
Just a few of the many topics i found about this error.
I bought my laptop January 2009 as a demo model from a dutch store called Qplaza http://www.qplaza.nl/
Don't think i have any warranty beside the warranty i got from that store (2 years) but there are a few things i don't understand.
From what i understand is that there even was a lawsuite about this problem and that there indeed was a problem with the nvidia 8600 chips. But then why won't Toshiba or Nvidia fix the laptops with those problems?
From what i have read my laptop would have to go to special repair service to replace my motherboard and i will have to pay for that myself.
And that is IF they can fix my laptop.
I started searching the internet what the price costs might be but the answers didn't make me a very happy woman :-(
Isn't there another way to fix this problem?
And aren't there places where you can buy a suitable motherboard for this laptop?
Can anybody please help me?? My laptop was working perfectly and without any warning..poof...can't get it to work anymore.

Dear Debzel,
As the proud owner of an attractive piece of scrap with G40 stamped underneath, due to what is almost certainly the same fault as you have, I have been through the customer service route and found that they are not going to officially recognise that the n-vid fault exists on our laptops and will only offer you a repair at your cost.
Due to the conspicuous lack of messages on this forum regarding this inherent fault, I suspect that this message may be quickly removed from the site. Having taken advice from the chap who runs the n-vid defect website, I realise that the only way forward is to take on Tosh legally. The consumer has strong rights in the UK as I suspect is parallel in Holland (assuming that's where you're based). I would be willing to send you my letters, based on templates from the defect website and Consumer Direct (phone them if you're i the UK and get it from the horse's mouth that your product should have lasted longer than it did - 08454 04 05 06), but with some information about my personal situation added.
You also have to send a copy to the credit card company that you used when making the purchase, if that was the case, as this puts you in a stronger position. If you didn't use a CC then that's a shame but not the end of the road, you can still take them on and by all reports, you should be successful as the PC is very young for the price you would have paid. The other repondent to your post must work for Tosh, which is why they were so unhelpful.
Kind regards,
steve oram at bt inter net dot com.

Panic[cpu11]/thread=2a100449cc0: pcisch-0: Fatal PCI bus error(s)

I got this panic when i do some testing on SUN cluster. Anybody could give me some suggestions?
Any comments are welcome.
Environment information:
SunOS arcsun48kh232ed1 5.10 Generic_118833-24 sun4u sparc SUNW,Sun-Fire
Sun Microsystems sun4u Sun Fire 4800
Solaris 10 (Sparc) ( patch latest 10_recommended_patch_cluster)
scate version: 1.4.1
sun cluster 3.1 u4 ( patch 120500-12)
SUN volume manager( with Solaris 10)
Crashed information:
bash-3.00# Dec 5 20:18:03 arcsun48kh232ed1 ip: WARNING: The <if>:ip*_forwarding ndd variables are obsolete and may be remove d in a future release of Solaris. Use ifconfig(1M) to manipulate the forwarding status of an interface.
Dec 5 20:18:03 arcsun48kh232ed1 last message repeated 3 times
Dec 5 20:19:32 arcsun48kh232ed1 DEV_STRESS: dev_stress_start: INFO: dev_stress successfully started
Dec 5 20:19:33 arcsun48kh232ed1 DEV_STRESS: : INFO: dev_stress_monitor successfully started
Notifying cluster that this node is panicking
SUNW-MSG-ID: SUNOS-8000-0G, TYPE: Error, VER: 1, SEVERITY: Major
EVENT-TIME: 0x457644ee.0x63a71d (0x1a01a2d86e0)
PLATFORM: SUNW,Sun-Fire, CSN: -, HOSTNAME: arcsun48kh232ed1
SOURCE: SunOS, REV: 5.10 Generic_118833-24
DESC: Errors have been detected that require a reboot to ensure system
integrity. See http://www.sun.com/msg/SUNOS-8000-0G for more information.
AUTO-RESPONSE: Solaris will attempt to save and diagnose the error telemetry
IMPACT: The system will sync files, save a crash dump if needed, and reboot
REC-ACTION: Save the error summary below in case telemetry cannot be saved
ereport.io.pci.sserr ena=1a01a29b42002c01 detector=[ version=0 scheme="dev"
device-path="/ssm@0,0/pci@18,700000" ] pci-status=4280 pci-command=146 pci-pa=
0
ereport.io.pci.rserr ena=1a01a29b42002c01 detector=[ version=0 scheme="dev"
device-path="/ssm@0,0/pci@18,700000" ] pci-status=4280 pci-command=146 pci-pa=
0
ereport.io.pci.sserr ena=1a01a29b42002c01 detector=[ version=0 scheme="dev"
device-path="/ssm@0,0/pci@18,700000/pci@2" ] pci-status=4290 pci-command=147
ereport.io.pci.sec-sta ena=1a01a29b42002c01 detector=[ version=0 scheme="dev"
device-path="/ssm@0,0/pci@18,700000/pci@2" ] pci-sec-status=a80 pci-bdg-ctrl=
23
panic[cpu11]/thread=2a100449cc0: pcisch-0: Fatal PCI bus error(s)
000002a100471e70 pcisch:pbm_error_intr+158 (300001d9bc0, 134cc00, 30000bbfdc8, 30000bbfdc8, 0, 300001d9580)
%l0-3: 00000300001c95b8 0000000000000000 000000000196a800 000000000196a800
%l4-7: 0000000000000001 000000000196a800 0000030000205830 0000000000000000
000002a100471f50 unix:current_thread+170 (0, 300031e8a98, 0, ffffffffffffffff, 300001c95b8, 8)
%l0-3: 00000000010076e4 000002a100449021 000000000000000e 0000000000000633
%l4-7: ffffffffffffffff 00000300061793d8 000000000000000b 000002a1004498d0
000002a100449970 unix:disp_getwork+38 (30003b74000, 18ab7c8, 180c000, 180c000, 0, 0)
%l0-3: 00000300001c95b8 ffffffffffffffff 00000300001c9580 00000300001c9680
%l4-7: 00000300001c9680 0000000000000000 00000300001c9680 0000000000000000
000002a100449a20 unix:idle+d4 (182bc00, 0, 30003b74000, ffffffffffffffff, 4, 182ac00)
%l0-3: 00000300031e8a98 000000000000001b 0000000000000000 ffffffffffffffff
%l4-7: 00000300031e8a98 ffffffffffffffff 00000000018ab7c8 00000000010554bc
panic: entering debugger (continue to save dump)
Welcome to kmdb
kmdb: unable to determine terminal type: assuming `vt100'
Loaded modules: [ crypto cpc sd ptm ufs unix krtld s1394 sppp wrsmd ipc nca
genunix ip sgsbbc logindmux wrsm isp usba specfs ssd nfs md random sctp ]
[11]>
Message was edited by:
sky.ma

Agreed, seems like a PCI bus error.
Data flowing through SB4 didn't like something, so cpu11 barked out a complaint.
Perhaps it was something passing to or from your storage
or to and from the other partner pair.
Install Explorer, as per Public Infodoc 82329,
run it to gather a system configuration snapshot,
and then go open a support case with Sun.
At the very least, you'll find it was simply a result of a typo
in the modifications you were making to your configuration.
Best to let Sun Techsupport figure this out for you.

Error-201003

Greetings. I am getting error-201003 each time I run my code. I have copied the DAQ assitant sub-vi from another vi where it is working perfectly. I feel that this should rule out ni-daqmx settings as my problem. Has anyone had a problem like this before?
Attachments:
Labview Throttle Controller_tab control_buttons_usb.vi ‏123 KB
CSV import.vi ‏15 KB
Button Selection.vi ‏11 KB

Hi Pushrod,
What hardware are you using? Can you attempt to recreate the DAQ Assistant from scratch in the VI you are wanting to run? Check to make sure you are still referencing your DAQ device in the right Dev identifier.
Kyle A.
National Instruments
High Speed Digital I/O Product Support Engineer - R&D

What device I have to connect with my PCI - 4351 to mesure a strain gauge signal?

Hi,
I have a PCI - 4351 with a TBX-68T messuring some termocouples signals, but I want to mesure a strain gauge too, what devices I have to connect my PCI - 4351 to make it possible?
Thanks.
Rafael.
U.F.R.J. Engineering student.
Brazil.

Q: what do i have to do to connect my devices to my jetpack??
A: Jetpacks are wireless only devices. You need to open up your computers wireless network list and select the network being broadcasted by the Jetpack. Once you find the network then connect to it by entering the WiFi password provided on the back of the Jetpack.
Q: what's the phone # for ???
A: VZW is a phone company. Every device that connects to the VZW network has a phone number associated with it that allows it to dial in. Although your Jetpack uses a phone number there is no need for you to have to enter or use it on anything other than for billing purposes.
Q: it appears that my tablet has already picked up the jetpack as a connection. is that it ???
Yes. The Jetpack should be broadcasting some kind of unique network name. The default network name (SSID)should be on a white sticker on the back of the Jetpack.
Q: I have another device at a different location. how do I get that device connected to the jetpack ??
A: Jetpacks have a very limited range. You need to bring your devices within the wireless radius of the Jetpack in order for them to connect to it. Normally a jetpack can only reach 1 room away from its current position, they are not as powerful as a normal home wireless router.

Pci controller error

Hye guys really need assistance!!!
My laptop cannot boot up to windows, always shows pci controller error and auto restart..
Any idea??
This question was solved.
View Solution.

Have you checked with win 7 OS alternatively please provide the exact error code.
I'm an HP Employee.
The opinions expressed here are my personal opinions, not of HP.
Make it easier for other people to find solutions, by marking an answer “Accept as Solution” if it solves your problem.

NI PCI-4351

Hi,
We have NI PCI-4351 working in Windows 98.
We are exploring to move to Windows 7 and CVI.
Has anyone this combination and how did you get on?
Thanks
Simon

Simon,
1-
Compatibility-wise see here. It says the NI-435x driver is not supported in Win7.
You might have to re-code the app with DAQmx, which is supported.
2-
Probably your Win98 machine is an old one. So, another a major source of problems might be the timings.
Your current application might have been running without problems because it is somehow "tuned" for that computer.
The new faster computer will be doing things much faster and in multiple cores.
You might run into some race conditions due to some thread timing issues.
Hope this helps,
S. Eren BALCI
www.aselsan.com.tr

PCI 4351 error 201003

Similar Messages

Maybe you are looking for