PCI-7334, Error code 7005

When I open Measurement & Automation Explorer I cannot communicate with the PCI-7334. The error I get is: 70005 (NIMC_boardFailureEreor).
What I did was to try to update the firmware. However, the following message appeared and it was not possible to proceed: "Error configuring the board for download. Please ensure that the board is in a reset state and that no other application is communicating with it".
I try to give some information that may be useful to understand the problem.
The status of the controller is:
- Ready to receive: GREEN
- Data in the return data buffer: GREEN
- Command in process: GREEN
- Pocket error: GREEN
- Power up reset: RED
- Modal error message: RED
- Hardware failure: RED
Moreover, the version of NI Motion is 6.1.2.
I read on the forum that this problem may be related to a hardware failure. Can I try to do some other checks before sending the card to repair?
Thank you,
Giuditta

Giuditta,
it's very likely, that you will have to send the board for repair. However to make sure, that you are not only facing an installer issue on the PC (which is quite unlikeyl) you may want to install a later version of NI-Motion on another PC and try to do a firmware upgrade there.
Kind regards,
Jochen Klier
National Instruments

Similar Messages

Windows 7 - Pci-to-Pci Bridge (Error: Code 10) - PCI Video Card

Before I state my issues I will list what I'm running and what I'm trying to accomplish.
I'm running Windows 7 Enterprise 64-bit edition, not the Beta or RC. I have 3 video cards in my possession (listed below).
- (PCIe) Evga GTX260
- (PCI) Evga 9400GT
- (PCI) Evga Fx5500
Out of those 3 cards I only use the GTX260 and the 9400GT. I had to 'retire' the Fx5500 because the latest WHQL (certified) drivers only provide support as far down as the "6 series" Nvidia cards. Unfortunately the Fx5500 is a "5 series" and falls below that line. I have already tried to use the GTX260 and Fx5500 in previous versions of Windows (XP and Vista), but there is no way to download and install two separate drivers for two of the same make of video card - you'll get nothing but errors. There is the option of going to a place like guru3d.com and downloading a custom supported driver that covers both the GTX260 and Fx5500, but the drivers are not certified and lack support. Therefore, I purchased and now use the 9400GT which is covered under the drivers for the GTX260 and eliminates the need for messing around with custom drivers. Also, the 9400GT has a better graphics processor and more memory than the Fx5500, so it was time to upgrade anyway.
Now that you have some background info here is my issue Whenever I install the 9400GT I get a second 'pci-to-pci bridge' entry (the other entry has no errors) that shows up under 'System Devices' in the Device Manager. The second pci-to-pci bridge entry has a yellow triangle with an exclamation mark on it that refers to a problem. When you check the properties of this device it more or less says that Windows has detected a problem (Error Code 10). The GTX260 still works and even shows up under the 'Display Adapters' as a GTX260, but no entry for the 9400GT exists. I have tried the 9400GT in both PCI slots and each time it does the same thing. If I pull out the GTX260 and ONLY run the 9400GT, I still get the pci-to-pci bridge issue, BUT I do get a picture and can boot into Windows 7 without a hitch. When I do this there is still nothing listed under the 'Display Adapters' as a 9400GT or even a VGA compatible device.
After messing around with this for 10 hours (yes, I said 10 hours) I decided to dig out my retired PCI video card (the Fx5500). When I installed this card I had no 2nd pci-to-pci bridge entry appear under 'System Devices', and the one that was listed had no yellow triangle or error codes. I then checked under 'Display Adapters' and Windows 7 had recognized it as a VGA compatible device and was asking for drivers.
I have now concluded that there is definitely no issue with the motherboard or any of my hardware (including video cards). At first EVGA Support and I had suspected that the motherboard may be bad because of all of the pre-diagnostic steps I had taken during my 10 hour ordeal. I'm not going to list everything I did because it would literally take 3 hours to type it all in. Just believe me when I say that I have tried most things including but not limited to the latest bios updates (flashed 4 times and completely reset to ensure accuracy), custom IRQ management, entire OS re-installation X2, multiple/latest chipset drivers installed, multiple/latest video drivers installed, memtest testing, complete hardware teardown and re-build (adding one device at a time), and MUCH more. The only thing I did not try was installing a different OS other than Windows 7 64-bit to see if I could replicate the issue. This is a waste of time though because lets say that I install Windows XP Pro and the 9400GT doesn't have this issue... Well, that's great, but who gives a damn about XP Pro when I have been using it for the last 9 years and when I have a full version of Windows 7 that I want to use? I'm certainly not going to run XP Pro over Windows 7 just to use this PCI video card. Second, if I install XP Pro and it still gives me the same pci-to-pci bridge error then again, I've only wasted more time because if its not going to work in either OS then Im sure as hell not going to leave XP Pro installed when I can use Windows 7.
Thanks,
piyush

Maybe stupid question now but has your posting anything to do with Toshiba and Toshiba notebooks?

PCI 6224 error code -88302 during self test

Hello,
I'm having a problem with self testing my PCI 6224 board in my computer. I am able to run 2 different boards successfully on 2 different computers, but this computer is seeming to give me troubles.
When I open NI MAX to run self test, it gives me an error code -88302 and says issue with connection. I tried unplugging the DAQ to my circuit and running the self test again but got the same error.
How can I further trouble shoot this problem to take my next steps to resolving this?
Thanks,
Brandon Deal
Brandon Deal
RDD Intern
Solved!
Go to Solution.

Yeah, at this point it does sound like a software problem on this particular compute - most likely an issue with DAQmx. What version of DAQmx do you currently have installed? When you were trying the first troubleshooting steps I recommended, did you just repair DAQmx, or did you upgrade to the latest version of the driver? If you just repaired your existing installation, you can try upgrading to DAQmx 9.8 instead. You can download DAQmx 9.8 from the link below.
NI-DAQmx 9.8
http://www.ni.com/download/ni-daqmx-9.8/4297/en/
You can also try resetting the MAX configuration data. While it is rare for it to happen, the MAX configuration database can become corrupted, which can cause sytem issue like you're seeing. Follow the steps in the document below to reset the configuration data.
What is the Process for Resetting the MAX Database?
http://digital.ni.com/public.nsf/allkb/2C7480E856987FFF862573AE005AB0D9
At this point it's probably just a matter of pinpointing which piece of software is malfunctioning/corrupted and repairing/reinstalling it. You can continue trying to do that for this machine, or, if you do have another working machine available, you could switch to that computer - whichever is more convenient for you.
Regards,
Ryan K.

Pci to pci bridge error code 35 after installing my new graphics card

hello everyone
first of all i am not sure if in the right section of the forum to post this...if not i am sorry.
well about my problem...i ve bought this new graphics card msi geforce gt430 and a new psu which is 580 watt and yesterday i installed em both.and then i turned on my pc. the thing is windows cant detect my grsphics card.there is this yellow exclamation mark on pci standard pci to pci bridge in device manager menu.i tried uninstalling pci to pci bridges and rebooting my pc.it didnt help.i also tried updating every single driver again nothing changed.i also have one of the latest bios so i dont think it should be related to bios.i have no idea how to fix this.i am a little bit ignorant when it comes to pc hardware.i can use all the help i can get.
thanks for your helps in advance.
astinwald

Yup, wrong part of the forum.
Sven will move it next time he's here.
Pci2pci is a motherboard thing but could interfere with gfx detection.
I know you said you'd reinstalled all drivers but...
Did you get the latest drivers for your motherboard?
If that doesn't fix it I guess the next step would be a complete OS reinstall...

Error Code 10 with GPIB PCI Card

PC used: Dell optiplex GX110, lastest Bios release, Windows 2000 SP4, GPIB Drivers version 2.2, Local Admin session.
After having install the driver (without the GPIB)and plug the card, this one is automaticaly recognised by the Os.
But, after the reboot (asked by the OS to validate the installation), the GPIB card appears, in the device manager, with an error code 10 (not started)....
I tried with two (new) differents GPIB PCI Card, two OS (First time with NT4.0 SP6 Drivers 1.7 and now, Win2000 SP4 Drivers 2.2) and with two PCs Dell Optiplex GX110 !
I even tried with a "Ghost" from an other PC (also an Optiplex GX110, with the same model of GPIB Card)
-> I obtain the same error each time !
Help me please..........

Hello,
Could you give me the exact reference of the board (PCI-GPIB, PCI-GPIB+, AT-GPIB, AT/GPIB-TNT...)?
Is the error code displayed on the Windows device manager (in the properties dialog box of the device)?
What is the exact description of the error code?
A PCI-GPIB installation do not need to reboot the OS if the NI-488.2 driver is correctly installed. The board should be recognized in MAX and you must be able to scan for instruments and start I/O communication with the device from test panels in MAX.
Update me as soon as you receive another feedback.
Regards.

"Error Deleting Device" when removing PCI-7334 in MAX

I added a Virtual NI-Motion device by doing the follwoing in MAX:
Right click "Devices and Interfaces"->Create New->Virtual NI Motion Devices->Virtual 7334
Now my hardware has arrived, but when I installed the card in a PCI slot, no new devices were listed. There was only one entry, with the device status of "Device is not responding or has been removed from the system". I wanted to remove this device, but was unable to. I do the following:
Right click "PCI-7334 (1)"->Remove Device
After answering yes to the dialogue, I get a pop-up that says "Error Deleting Device". How can I get around this problem?
Thanks for the help!

Hi Jay,
It sounds like there might have been some sort of corruption in the data file in Measurement and Automation Explorer. I recommend deleting the Data folder in the following directory:
...Documents and Settings\ All Users\Application Data\National Instruments\MAX
This will simply cause MAX to reinitialize its settings. Any saved information such as Tasks and Configurations will be lost though.
Thanks,
Wes P.
Applications Engineer
National Instruments
Wes P
Certified LabVIEW Developer

C260 Hardware Scan error code "WPE001001-HK7X6I" PCI EXPRESS-SYSTEM

I have this error on my all in one -Do i need to do anything with it - If it is related to the Card Reader Slot- then this is currently not being used.
thanks
Mike Morson

Hi daus_95gen welcome to the forum, I don`t know what the error code means, Only lenovo will know that, What i do know is that it points to your graphics hardware, But don`t panic yet lol.
My suggestion is to go to the lenovo support site, Enter your laptop series name (in your case the G400) in the search engine & see if there are any driver updates for your pc, If there are download & install them.
Once the drivers are installed run another hardware test, If all goes well you should not see another error code.
Let us know how things work out.
Catt

Two Days of Restore Error Code 6... HELP!!!

I have an iPod Touch that's about two years old. I no longer have access to the laptop that it is normally synced to, so I downloaded iTunes on the family computer. After hours upon hours of problems (not syncing, or showing that it successfully synced but getting a "no content" error once it turned back on) I thought maybe it was my iPod that was messing up and not the computer. I reset my iPod through holding down the home button and the power button, and I'm now at the screen that shows the USB cord with an arrow pointing towards the iTunes symbol.
I tried to restore on iTunes, and it will get all the way through until "verifing restore," and then I will get a pop up that says the process could not be completed because of an unknown error (error 6.)
I uninstalled iTunes and installed an earlier version of iTunes, but then my computer wouldn't even recognize my iPod. I reinstalled the latest version of iTunes and Quicktime. Still getting the same error code.
I am on an Administrator account, running Windows Vista 64 bit, and everything is up-to-date. All anti-virus and firewalls are turned off. I've followed all of the steps outlined on the Apple site, and I am down to paying $29 for a phone call to Apple. (Ha! Over my dead body!) I don't have another computer to try it on. I've used two different iPod cords (mine and the cord from another iPod), and have tried out all of the USB ports on the computer.
I'm really hoping someone could help me with this before I lose my mind.
I'm fairly computer literate, but I'm not a whiz. Please don't feel the need to break things completely down into laymans terms, but please don't use pure tech-speak(:
Diagnostics:
Microsoft Windows Vista x64 x64 Home Premium Edition
Service Pack 2 (Build 6002)
HP-Pavilion NC686AA-ABA a6700y
iTunes 10.4.1.10
QuickTime 7.7
FairPlay 1.12.20
Apple Application Support 2.0.1
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.1.2
Apple Mobile Device Driver 1.57.0.0
Bonjour 3.0.0.2 (333.2)
Gracenote SDK 1.9.1.485
Gracenote MusicID 1.9.1.102
Gracenote Submit 1.9.1.133
Gracenote DSP 1.9.1.43
iTunes Serial Number 00B3B0A00BAFB508
Current user is not an administrator.
The current local date and time is 2011-09-28 18:09:41.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is supported.
Video Display Information NVIDIA, NVIDIA GeForce 6150SE nForce 430
**** External Plug-ins Information **** No external plug-ins installed.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name:     {154BA537-EF26-4015-BE91-6ACFA30865E5}
Description:     USB Wireless 802.11 b/g Adaptor
IP Address:     0.0.0.0
Subnet Mask:     0.0.0.0
Default Gateway:     0.0.0.0
DHCP Enabled:     Yes
DHCP Server:
Lease Obtained:     Wed Dec 31 17:00:00 1969
Lease Expires:     Wed Dec 31 17:00:00 1969
DNS Servers:
Adapter Name:     {3BF6C369-3C76-4358-997A-8DE3B494BFE8}
Description:     NVIDIA nForce 10/100 Mbps
Ethernet IP Address:     192.168.254.3
Subnet Mask:     255.255.255.0
Default Gateway:     192.168.254.254
DHCP Enabled:     Yes
DHCP Server:     192.168.254.254
Lease Obtained:     Wed Sep 28 17:12:00 2011
Lease Expires:     Wed Sep 28 17:11:59 2011
DNS Servers:     192.168.254.254
Active Connection:     LAN
Connection Connected:     Yes
Online:          Yes
Using Modem:     No
Using LAN:     Yes
Using Proxy:     No
SSL 3.0 Support:     Enabled
TLS 1.0 Support:     Enabled
Firewall Information
Windows Firewall is off.
ZoneAlarm Firewall is installed.
Connection attempt to Apple web site was successful.
Connection attempt to browsing iTunes Store was successful.
Connection attempt to purchasing from iTunes Store was successful.
Connection attempt to iPhone activation server was successful.
Connection attempt to firmware update server was successful.
Connection attempt to Gracenote server was successful.
Last successful iTunes Store access was 2011-09-28 17:14:05.
**** CD/DVD Drive Tests ****
No drivers in LowerFilters.
UpperFilters: GEARAspiWDM (2.2.0.1),   E: TSSTcorp CDDVDW TS-H653Z, Rev 4403 Drive is empty.
**** Device Connectivity Tests **** iPodService 10.4.1.10 (x64) is currently running. iTunesHelper 10.4.1.10 is currently running. Apple Mobile Device service 3.3.0.0 is currently running. Universal Serial Bus Controllers: Standard OpenHCD USB Host Controller. Device is working properly. Standard Enhanced PCI to USB Host Controller. Device is working properly. FireWire (IEEE 1394) Host Controllers: VIA OHCI Compliant IEEE 1394 Host Controller. Device is working properly. Most Recent Devices Not Currently Connected: iPod touch (2nd generation) running firmware version 4.2.1 Serial Number:     8K9436WJ75J **** Device Sync Tests **** No iPod, iPhone, or iPad found.

This Question can be best answered by someone who had the Same error pop up, but I'll try my best. You have an iPod touch 2nd Generation and you don't have anymore warranty for it. I hope you didn't jailbrake it or did something illegal with it like putting a new software on it that should not be on there. Here we go:
Go to your Friends house or anybody else you know that has iTunes on their Computer. Don't sync your iPod!
Try to restore the iPod, or try to put it as new iPod so it'll delete everything but you'll have your iPod problem fixed

Lenovo 3000 N100 Network issue / Wireless Stack initialization failed, error code 117

Hi,
Lenovo 3000 N1000 with 1GB Ram, Win XP SP2, purchased in May 2006. WLAN network with WPA-PSK key worked without any issues so far and is still accessible with PC.
After transferring music via from my notebook to my mobile Bluetooth all network adapters seem to be disconnected. Neither Access Connections (AC) nor Windows can find any wireless network. Also if I try to configure any LAN, WLAN with Windows I get the message that all network adapters have been removed. However I cannot spot any issue in the device manager as all parts are shown to be working OK.
This is what I've done so far:
1) Checked Radio switch ---> on
2) FN +F5 --> connection on
3) Uninstalled AC, downloaded and installed most actual version (5.00 Build 7VCX32WW)
4) Installed new version for wireless driver for Intel(R) PRO/Wireless 3945ABG (version 12.0.0.82)
Still, even if I uninstall AC to check if WLAN is working at all, Windows gives the error message that all network components have been removed.
Diagnose Tool gives the following output:
"Wireless Stack initialization failed, error code 117"
Logfile:
Description : Intel(R) PRO/Wireless 3945ABG Network Connection
Type : Wireless LAN Adapter
DriverVersion : 10. 5. 1. 59 ----> why is the old driver version??????????
PNPID : PCI\VEN_8086&DEV_4227&SUBSYS_10118086
SupplicantVersion : AEGIS Protocol (IEEE 802.1x) v3.5.3.0
ERROR AcSvc( SYSTEM(Prvlg).1108.4580) [9/3]11:04:15:703 CAcGolan::GetRadioStateInDriver: Golan API GetRadioState() missing!
Hope this is enough information for anyone of you in order to suggest any solution. As I could see from previous threads some of you experienced similar problems in the past and could fix them somehow. However I couldn't find anyone with exactly the same problem.
Thanks much in advance for any advice you might have.
Flo

Hi
I have this problem also with my Lenovo 3000 V200.
Sometimes when I boot up the PC it will connect to the network and everything works just fine.
At other times, after boot, the "wireless stack initialization failed, error code: 118" problem occurs
and the only way to solve it seems to be a PC restart. Nothing else I do will bring the network up.
If I study the Networking tab in Task Manager it indicates that no adapters are available (wired eth.
access also fails). At a few occations connectivity have failed alltogether (i.e. a reboot have not solved
the problem). Last time this occured I had to reinstall the complete system (from a previous backup)
to get networking up.
I have tried different versions of Access Connections (5.02, 5.12, 5.21) and the same problem occurs
at seemingly random instances in time. This is obviosly a problem with the Access Connections software
since the Wireless networking works fine when I let windows manage it...
Anyone with a fix?
/Fredrik

FS - Error code 3006 from SQL-Query

Hello world!
Can someone inform me which possible errors in a query cause the following error message after the query is activated?
Internal Error (3006) Message [131-183]
Until now I had only error code 1003, which signals syntax errors etc. in the query.
By the way: Does anywhere exists a list of error codes/messages occuring in SAP B1?
Thank you!
Frank Romeni

Error codes and their description can be found in SDK help files
I have pasted them below for your ref
-39
End of File
-43
File not Found
-47
File is Busy
-50
File Cannot Open
-51
File Corrupted
-99
Division by Zero
-100
Out of Memory
-101
Print Error
-103
Print Canceled
-104
Money Overflow
-111
Invalid Memory Access
-199
General Error
-213
Bad Directory
-214
File Already Exists
-216
Invalid File Permission
-217
Invalid Path
-1001
Data Source - Bad Column Type
-1003
Data Source - Alias Not Found
-1004
Data Source - Value Not Found
-1005
Data Source - Bad Date
-1012
Data Source - No Default Column
-1013
Data Source - Zero/Blank Value
-1015
Data Source - Integer Overflow
-1016
Data Source - Bad Value
-1022
Data Source - Other File Not Related
-1023
Data Source - Other Key Not In Main Key
-1025
Data Source - Array Record Not Found
-1027
Data Source - Value Must Be Positive
-1028
Data Source - Value Must Be Negative
-1029
Data Source - Column Cannot be updated
-1100
Data Source - Cannot Allocate Environment
-1101
Data Source - Bad Connection
-1102
Data Source - Connection Not Opened
-1103
Data Source - DB Already Exists
-1104
Data Source - Cannot Create Database
-1200
Data Source - Data Bind General Error
-2001
Data Source - Bad Parameters
-2003
Data Source - Too Many Tables
-2004
Data Source - Table Not Found
-2006
Data Source - Bad Table Definition
-2007
Data Source - Bad Data Source
-2010
Data Source - Bad Data Source Offset
-2013
Data Source - No Fields In Table
-2014
Data Source - Bad Field Index
-2015
Data Source - Bad Index Number
-2017
Data Source - Bad Alias
-2020
Data Source - Bad Alias
-2022
Data Source - Bad Field Level
-2024
Data Source - Not Matching Data Source
-2025
Data Source - No Keys In Table
-2027
Data Source - Partial Data Found
-2028
Data Source - No Data Found
-2029
Data Source - No Matching Field
-2035
Data Source - Duplicate Keys
-2038
Data Source - Record Lock
-2039
Data Source - Data Was Changed
-2045
Data Source - End of Sort
-2049
Data Source - Not Opened for Write
-2056
Data Source - No Matching With Current Data Source
-2062
Data Source - Bad Container Offset
-3001
Query - Field Not Found
-3003
Query - Bad Data Source
-3004
Query - Bad Token
-3005
Query - Token After End
-3006
Query - Unexpected End
-3008
Query - Too Long Query
-3009
Query - Extra Right Parenthesis
-3010
Query - Missing Right Parenthesis
-3012
Query - No Operation Code
-3013
Query - No Field In Comparison
-3014
Query - Bad Condition
-3015
Query - Bad Sort List
-3017
Query - No String
-3018
Query - Too Many Fields
-3019
Query - Too Many Indexes
-3020
Query - Too Many Tables
-3021
Query - Reference Not Found
-3022
Query - Bad Range Set
-3023
Query - Bad Parsing
-3025
Query - Data Bind is Missing
-3026
Query - Bad Input
-3027
Query - Progress Aborted
-3028
Query - Bad Table Index
-3032
Query - General Failure
-3033
Query - Empty Record
-3036
Query - Bad Parameter
-3037
Query - Missing Table in List
-3040
Query - Bad Operation
-3041
Query - Bad Expression
-3042
Query - Name Already Exists
-3044
Query - Time Expired
3001
Form - Is Not Initialized
3002
Form - Bad Data Source
3003
Form - Exceeded Data Sources Limit
3006
Form - Invalid Form Item
3007
Form - Exceeded Forms Limit
3009
Form - Too Many Saved Data
3012
Form - Invalid Form
3015
Form - Cannot Get Multi-Line Edit
3016
Form - Bad Item Type
3017
Form - Bad Parameter
3023
Form - No Message Callback
3029
Form - Item Is Not Selectable
3031
Form - Bad Value
3033
Form - Item Not Found
4007
Grid - Invalid
4008
Grid - Bad Size
4009
Grid - No Data
4011
Grid - Invalid Parameters
4013
Grid - Not Super Title
4014
Grid - Super Title 2 Exits
4015
Bad Item Unique ID
4016
Grid - Bad Data
4017
Grid - Column is Already Folded
4018
Grid - Column is Already Expanded
4019
Grid - Line Exists
4020
Grid - Not Enough Data
4022
Grid - Super Title Exists
4027
Grid - Row Is Not Collapsible
8004
Status Bar - No Such Info
8005
Status Bar - Info Occupied
8006
Status Bar - No Message Bar
8007
Status Bar - Progress Stopped
8008
Status Bar - Too Many Progress
5001
Graph - Invalid
5002
Graph - Bad Form Item
5005
Graph - Bad Parameters
-7008
Form not found
-7000
Invalid Form
-7031
Form - Reserved /Illegal form Unique ID
-7032
Form - Invalid Mode
-7006
The item is not a user defined item and cannot be manipulated in such manner
-7005
Invalid table name
-7004
XML batch load failed
-7003
Menu operation Add failed
-7002
Function not supported
-7001
Invalid Item
-7034
Could not clear item in group
-7033
Out of boundaries
-7020
This method cannot be invoked by a Cell object
-7019
Invalid form unique ID. Should not begin with an F_ prefix
-7018
Invalid Field Value
-7017
Invalid Field Name
-7016
This datasource object is not a user-defined object
-7015
Invalid Column
-7014
A Column object with the specified unique ID already exists in the system.
-7013
The string value entered should be less then 10 characters.
-7012
An Item object with the specified unique ID already exists in the system.
-7011
The string value entered should be less then 11 characters.
-7010
A form with the requested unique ID already exists in the system.
-7009
The string value entered should be less the 32 characters.
-7040
Cannot Load XML File
-7051
Unexpected usage of the specified XML TAG.
-7050
This action type is not valid or not implemented yet.
-7043
Cannot load the Menu resource from the specified XML file.
-7042
Cannot load the Item resource from the specified XML file.
-7041
Cannot load the Form resource from the specified XML file.
-7071
Failed to create the items group.
-7070
UID
-7069
Failed to change the form current pane level.
-7068
Failed to change the form color.
-7067
Failed to change the Form mode.
-7066
Failed to fix the form default button.
-7065
Failed to change the form Visible state.
-7064
Could not change the form title.
-7063
The change of form dimensions has failed
-7062
Unknown Form attribute
-7061
XML batch resource update is not supported yet.
-7060
Reached Max Number of user data sources.
-7094
Failed to add the items child objects.
-7093
Failed to batch add the items
-7092
Failed to bind the item to the data source
-7091
Wrong Item Attribute
-7090
Unknown Field Type
-7114
Type of Column is Not Supported.
-7113
Failed to add the column child objects.
-7112
Failed to add the new columns.
-7111
Failed to bind the column to a data source
-7110
Invalid column attributes
-7133
The specified menu position is not valid
-7132
Invalid menu type
-7131
Failed to add the menu object
-7130
The specified menu already exists.
-7030
Invalid Row Number
-7029
Operation not supported on system form.
-7028
Out of boundary of DB data source offset.
-7027
The menu item is not a user defined menu item and cannot be manipulated in such manner.
-7026
Menu item was not found
-7025
Unknown Form State
-7024
Failed setting form bounds
-7023
Invalid Target
-7022
Could not commit action because the item is currently in focus.
-7021
Operation could not be set on extended edit text item.
-7200
Your connection string doesn't much UI development work mode.
-7201
The specified connection string is not valid.

Cannot Complete KB2919355 Update, Error Code : 0xc0000001

Hello,
I encountered the MS KB2919355 update problem last year, and did not succeed in installing this update. I returned to the problem a few days ago and made some progress, however full installation is still elusive.
I have a HP m7-J010DX notebook, E0K83UAR, Intel Core i7-4700MQ CPU, Win 8.1x64
All other Windows & HP updates are installed.
I followed the advice in another message, and performed the following operations,
------------------------------------------------- KB2919335 Installation Procedure
1. download and install
KB2959977 2.8MB (Jan/11/2015, already installed)
KB2938439 19.6MB
KB2937592 303KB
KB2934018 126.4 MB
KB2932046 48 MB
2. Next, resetting Windows Update components
WindowsUpdateDiagnostic.diagcab (downloaded and ran, fixed two things)
3. The next step is performing a System File Check
CMD as Admin: "sfc /scannow"
Result: (I fixed this later, see below)
Windows Resource Protection found corrupt files but was unable to fix some
of them. Details are included in the CBS.Log windir\Logs\CBS\CBS.log. For
example C:\Windows\Logs\CBS\CBS.log. Note that logging is currently not
supported in offline servicing scenarios.
3b.
Found the following command,
CMD as Admin: "Dism /Online /Cleanup-Image /RestoreHealth"
The restore operation completed successfully.
The component store corruption was repaired.
Went back to step 3 ("sfc /scannow") and now received
"Verification 100% complete.
Windows Resource Protection did not find any integrity violations."
4. Next, please remove KB2919355
CMD as Admin:
"dism /online /remove-package /packagenameackage_for_KB2919355~31bf3856ad364e35~amd64~~6.3.1.14"
(funny symbol should read "colon capital-p")
5. The WinSxS folder also has to be cleaned.
CMD as Admin:
"dism /online /cleanup-image /startcomponentcleanup /resetbase"
6. Restart computer and then run the offline installer:
Windows8.1-KB2919355-x64.msu (KB2919355 690.8 MB)
7. Restart computer during the process whenever it is required.
Updating Computer
...30% complete
Do not turn off your computer.
This is when a problem occurred...
circling dots moved to LHS of screen, computer restarted,
"Your PC ran into a problem and needs to restart
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED
Error Code : 0xc0000001"
Used,
F8
"Option 5 : Safe Mode with Networking"
after restart,
"we couldn't complete the updates
undoing changes
Don't turn off your computer"
After a further restart the computer returned to logon.
I would appreciate advice on how to proceed in order to complete installation of this update.
Thank you.

I read elsewhere that using the Advanced Options/Automatic Repair procedure could fix the installation.
I tried this, it did not work, and now the situation is worse. The error report has changed to,
The boot config data for your PC is missing or contains errors
File : \EFI\Microsoft\Boot\BCD
Error code : 0xc000000f
The "Press F8 for Startup Settings" option no longer appears, and I can no longer get back to the log in screen and use the computer.
I still have Troubleshoot options,
1. Refresh your PC
2. Reset your PC
3. Recovery Manager (leads to USB based HP Recovery Manager
after about 110sec of blue screen)
4. Advanced Options
4. Advanced Options leads to,
1. System Restore
2. System Image Recovery
3. Automatic Repair
4. Command Prompt
5. UEFI Firmware Settings
Every option that I have tried has failed. I do no appear to have a restore point set (though I thought that I did) so I cannot restore to an earlier date.
F9 Boot Device Option/Boot Manager shows.
1. OS boot Manager
2. USB Hard Drive (UEFI)
3. Boot From EFI File
4. Notebook Hard Drive
5. USB Hard Drive
3. Boot from EFI File leads to a three options the first of which is,
NO VOLUME LABEL, [Acpi(PNPxxxx, 0)/Pci(yyyy)/Usb(zz, 0)/HD(Part1, Sig00000000)]
and thus eg.(there are other folders), EFI\Boot\en-gb\bootx64.efi.mui for the USB Recovery Drive which leads back to USB Drive Recovery Manager.
There are also two other options, one for the main SSD that will no longer boot, and the other for the computers second drive (the original HDD) that has an earlier version of a booting drive C: (I cloned from the HDD -> SSD and use the HDD as a backup drive, however I left the original partitions in place).
If I try to boot from the earlier data on the HDD (I did not really expect this to work completely) I get to the login screen, and an earlier password initially appears to be accepted, I get a brief Welcome, and then "The password is incorrect. Try again."
I have a recent file backup and am figuring out a way to make a current file backup.
I then plan to attempt a minimized image recovery or system recovery, unless I find a way to return to the login screen.
Any suggestions ?
Thank you.

HP recovery could not restore computer error code 0xe0ef000e

I bought a nice Solid State drive. Unfortunately it is not possible to upgrade my system to new hard drive. It fails every time with HP recovery could not restore computer error code 0xe0ef000e. This is after removing everything... graphics card, ram, cd drive... nothing is plugged in except the keyboard, monitor and mouse.
Windows 8 strikes again. Does anyone have any suggestions about how to actually use the recovery disks to reinstall windows 8 onto a new solid state drive. I hate this computer and wish I would have never bought it actually. It's been nothing but crap from day one.

It's the HP 500-023w desktop. I ended up just buying a Winodws 8.1 OEM disk and installing that on the SSD. The recovery tool is a bit useless. Reading through various forum posts it seems I would have ended up spending hours trying to figure it out or else buying the recovery disks from HP. Just paying $89 for an OEM disk is a good deal by comparison since at the very least the computer has no bloatware on it now.
What a hugely unnecessary hassle really. Now if only I could get this heap of junk to boot with a PCI-e graphics card installed I might actually be able to use it with two monitors. Good grief.

Odd error originating from NI-5411 (Error code: BFFA0002) when trying to load arbitrary waveform

Hello everyone.
We have some equipment (PCI NI-5411) that is misbehaving in an odd and new way. When trying to load an arbitrary waveform onto the AWG (using a library call to the "niFgen Write Binary 16 Waveform"), it produces an error. The error code is "BFFA0002", but I haven't been able to find any information that can show what this error code provides. Previously, we had some problem when the system wouldn't find the file and produces an error even though the file is there. After changing our code so the file access is attempted several times, the problem was resolved. However, that doesn't work in this case and we do not know here the problem is.
This is a pretty much shooting wild and hoping that something falls down, but if anyone could provide me with information about the error code or another probable error source I would be highly grateful.
Thanks in advance!
With best regards,
Niclas

Hi Niclas,
That error code suggests that a file cannot be opened. This error is defined in IVI as IVI_ERROR_CANNOT_OPEN_FILE.I don't think we return this error code from the NI-FGEN driver.
You mentioned that you have an issue with finding a file. Is that file specific to your application? How is it being open or used? What API do you use to open that file?
For NI-FGEN specific error code (and generic IVI error codes), you can query the error message by calling niFgen_error_message function or niFgen Error Message.vi.
Thanks,
- Liusdi

Problem updating the Firmware on a PCI-7334

About me: I am pretty new to the Labview/NI landscape so I may be missing something here! That said im very technically aware in general and believe I understand what is going on here.
Background: This NI PCI-7334 board has been taken from currently unused project stock so current physical condition of board is not really known (ie was not recently working) although it appears to be in good physical order.
Attempting to setup a new Labview 7 Express development environment on new PC hardware with a clean build of Windows XP Pro SP1 along with 1 x IMAQ PCI-1411 and 1 x IMAQ PCI-1408.
Attempting to update the PCI-7334 with the latest firmware in NI Motion 6.1.2. I select the option "Update All Firmware Sectors" f
rom the firmware tree by right mouse clicking. It starts off with the buttonless (ie No Cancel Button) file transfer progress dialog box. But after about 30 seconds I keep getting the error "Error configuring the board for download. Please ensure that the board is in a reset state and that no other application is communicating with it."
Existing Firmware versions are listed in NiMAX as:
68331 - 6.00.3012
DSP - 6.00.3008
FPGA1 - [BLANK*]
FPGA2 - [BLANK*]
*Listed in tree without a version
Unusually under the General listing I get "0" for the device serial number!
When I go into the "Status" area and choose the "Reset Device" option I eventually get these status lights (red):
Ready to Receive
Power Up Reset
Modal Error Message
0x80 Move Complete Status
I have tried removing all other cards from the PC to ensure there is not a compatability issue.
At this stage it would appear that it is a hardware problem so I was wondering what options I have available to g
et this card repaired. Is repair by NI economically viable or is a new puchase a better approach? IE are repairs done at a fixed price or based on materials and labour?
Please advise!
Thanks, Rod.
Attachments:
NI_PCI-7334_Firmware_Update_Error.zip ‏115 KB

I agree with your diagnostics. It looks like something went wrong during the last firmware update. The only solution for this problem is to send the board for repair.
NI has fixed prices for repairs which are much cheaper than buying a new board. Please contact your local NI branch for details.
Best regards,
Jochen Klier
Applications Engineering Group Leader
National Instruments Germany GmbH

Controling a sigma koki motorrized stage via a PCI 7334

Hi everyone,
I am trying to control a sigma koki motorized stage via a PCI 7334.
The motor is a stepper motor.
For information, here is the connection diagram of the stage via the driver (SG55M on the diagram) to the controler:
http://www.sigma-koki.com/english/D/SteppingMotors/Diagram/Diagram/Diagram.html
I ran a selftest on the motor using the driver and everything is going well.
As a first step of my design, i would just like to control the motor without any feedback, and without limit switch options.
I am using a 1:1 connector CB68LPR from NI to connect the driver to the PCI 7334. Doing this, i provide CW and CCW signals from the PCI to the driver as well as the inhibit signal. Thus, I come up using the pins 1,35, and 6 of the 68pins connector. Looking at other threads posted on NI, I believe those connections are enough to observe a simple move of my motor isnt it?
When i try out within MAX to test a movement using the 1 D interactive feature, my stage doesnt move.
MAX is confingured as followed:
> only axis1 enabled
> CW, CCW stepper mode
> limit and home switch disabled
> inhibit output setting enable
> ADC, PWM, ENcoder disabled since i dont use them so far
Those parameters are initializing the pci.
Is there other parameters that i should look at and which could prevent my motor to work?
While doing this first step, I monitor the signals from the PCI via oscilloscope and clock pusles are ok.
It is the first time i try to control a stepper motor using a PCI so i read the documentation to be found on Ni website, and i may just have forgoten something, but i cant see what...
Do i need to provide some additional signals? Or just with CW, CCW, and inhibit is ok?
If you find any comments or recommendations, they are welcome
Cheers ^ - ^

Hello Gegurissi,
To test the motor with a minimum configuration, you can connect CW, CCW, and digital ground lines to the driver.
It looks like that there is no ground connected to the motor, so please make sure that they are connected to the ground of the driver, too.
For the MAX settings, it seems fine, but the settings have to be saved and the board has to be initialized before the motor is moved.
In 1-D Interactive feature, please make sure that a value is entered in the "target position" section and click "apply" button.
Also, are there any error messages when you move the stage?
One last thing I would like to mention is that it is strongly recommended to use Universal Motion Interfaces (UMI) and Motion cables for the NI motion controllers.
The UMI devices are powered, such that they can provide necessary power to encoders, limit switches, etc.
If you have any questions, please let me know.
National Instruments Japan
Satoko Yuda

PCI-7334, Error code 7005

Similar Messages

Maybe you are looking for