Pda module - ao examples for 6024 E daq card

I am having trouble finding a working example of Analog Output for PDA (using a daq card 6024 E). Ni.com suggests using "PDA single point AO.VI" but I do not know how to configure channels. The website further states: "Single-point analog output is not supported in NI-DAQmx Base 1.0"
Essentially I have tried using both Configuration utility and MAX to set examples, but in both cases the example does not recognize them. Is there any other way to configure a channel?
Any suggestion will be greatly appreciated.
thanks,
-petar

Hi Petar-
I spoke with the engineer you reached over the phone and seemed to believe that you might be using the incorrect version of NI-DAQmx Base. With PocketPC you will need to use NI-DAQmx Base for PocketPC 2003. After uninstalling your current version and installing this new version you will need to also install the driver software to your PDA. This can be accomplished when connected to ActiveSync by choosing the option to install the driver to PDA in the Start>>Programs>>National Instruments>>NI-DAQmx Base folder.
You will need to create the task to be used in the NI-DAQmx Configuration Utility in Windows. First open the utility and click "Create New Task." Make sure you give it a descriptive name and choose the appropriate device type as well as selecting an analog output channel type. Click "Save and Exit" to save your choices.
You will then need to open LabVIEW and target your PocketPC 2003 device on the splash screen. Make sure that you do not open LabVIEW before saving the Task in the configuration utility or the task will not be referenced properly.
Finally, extract the zip file in this KB and open the "PDA Single Point AO.vi" and click "Run" in LabVIEW with the target set to the PDA. After a short time to build and deploy the app you should see the front panel appear on your PDA. I tested with a DAQCard-6024E with good results. Note with this example that you will need to click the "RUN" button each time you want to update the output voltage.
EDIT: I forgot to mention- if you receive a prompt for "ESeries.dll" you might have to browse to "C:\Program Files\National Instruments\LabVIEW 7.1\PDA\utilites\LVPocketPCProject\lib\DAQmxbase\ESeries.dll" to find the necessary file.
Hopefully this helps-
Message Edited by Tom W. on 07-27-2005 05:30 PM
Tom W
National Instruments

Similar Messages

Looking for examples of VI with two or more inputs for the 1200 daq-card ( PCMCIA )

Thank you , if you can help me by sending VI examples for the 1200 daq-card
, with 2 or mores inputs

You can find several examples that will work with the DAQCard-1200 at zone.ni.com/libraries/.
Then look under Data Acquisition. There are also examples that ship with
LV and NIDAQ. Look in ...\Labview\examples\daq\anlogin\.
"david frazao" wrote:
>Thank you , if you can help me by sending VI examples for the 1200 daq-card>,
with 2 or mores inputs>>

How to structure the DMA buffer for PXie 6341 DAQ card for analog output with different frequencies on each channel

I'm using the MHDDK for analog out/in with the PXIe 6341 DAQ card.
The examples, e.g. aoex5, show a single Timer (outTimerHelper::loadUI method), but the example shows DMA data loaded with the same vector size.
There is a comment in the outTimerHelper:rogramUpdateCount call which implies that different buffer sizes per channel can be used.
(the comment is: Switching between different buffer sizes will not be used)
Does anyone know what the format of the DMA buffer should be for data for multiple channels with different frequencies ?
For example, say we want a0 with a 1Khz Sine wave and a1 with a 1.5Khz sine wave. What does the DMA buffer look like ?
With the same frequency for each channel, the data is interleaved, e.g. (ao0#0, ao1#0; ao0#1, ao1#1, ...), but when the frequencies for each channel is different, what does the buffer look like ?

Hello Kenstern,
The data is always interleaved because each card only has a single timing engine for each subsystem.
For AO you must specify the number of samples that AO will output. You also specify the number of channels. Because there is only one timing engine for AO, each AO will channel will get updated at the same time tick of the update clock. The data will be arranged interleaved exactly as the example shows because each AO channel needs data to output at each tick of the update clock. The data itself can change based on the frequency you want to output.
kenstern wrote:
For example, say we want a0 with a 1Khz Sine wave and a1 with a 1.5Khz sine wave. What does the DMA buffer look like ?
With the same frequency for each channel, the data is interleaved, e.g. (ao0#0, ao1#0; ao0#1, ao1#1, ...), but when the frequencies for each channel is different, what does the buffer look like ?
In your example, you need to come up with an update rate that works for both waveforms (1 KHz and 1.5 KHz sine waves). To get a good representation of a sine wave, you need to update more than 10x as fast as your fastest frequency...I would recommend 100x if possible.
Update Frequency: 150 KHz
Channels: 2
Then you create buffers that include full cycles of each waveform you want to output based on the update frequency. These buffers must also be the same size.
Buffer 1: Contains data for the 1 KHz sine wave, 300 points, 2 sine wave cycles
Buffer 2: Contains data for the 1.5 KHz sine wave, 300 points, 3 sine wave cycles
You then interleave them as before. When the data is run through the ADC, they are outputting different sine waves even though the AO channels are updating at the same rate.

I use labview 8.0 and i can not run daqmx driver for pcmcia 6062e daq card

i use labview 8.0 on window xp .when i installed a PCMCIA daq card 6062E, i could not run daqmx driver.It is fine to see that the traditional version is working well.When i install daq card sometimes it is working well with traditional driver but mostly i see error on reading an analog input from PCMCIA daq device.An error called 'base adress' occures .I use last version of driver that is daqmx 8.0.1. and i have installed this correctly but again i could not see any signal on the test panel for daq-mx driver.I don't know what is the problem.Also when i install PCMCIA daq card Please reply this message.I need your helps.
Thanks

Hello,
Thanks for your reply.I will try to answer your questions.
I have checked the Device Mananger and I have seen that the device is detected by Windows XP. For another question the card shows up under both NI-DAQmx Devices and Traditional NI-DAQ (Legacy) Devices consistently in the Measurement & Automation Explorer.I use a way that I reset the driver for traditional NI-DAQ in MAX,and then i reset the device for NI-DAQmx driver in MAX and again i tried to run the test panel of DAQmx driver but again i saw a wrong signal or noise signal on the test panel i could not see the sinusoidal signal that i connected. i do get the test panels to run with the card using the DAQmx driver, But could not run the DAQ diagnostic utility.The error was as i specified below.
03.05.2006 09:49:35
Results saved to: C:\Documents and Settings\serkan\Desktop\Diagnostic Results.txt
Selected Device: Dev1
Device Type: DAQCard-6062E
Serial Number: 107509E
Device Support: (PASS)
NI-DAQmx Version: 8.0 (PASS)
Device Reset: (FAIL)
Error -50002 occurred at an unidentified location
Possible reason(s):
The specified device is not a valid device. The operation could not be completed as specified.
------ DIAGNOSTIC UTILITY ABORTED -----
And for your last question i can say that i have used the DAQ card on other laptops.But the results were the same.İ hope to see your reply
Thanks,
Serkan Buhan
Electrical-Elecronics Engineer
Researcher
TUBITAK-BILTEN

Method for accessing multiple DAQ cards

Hello, I am trying to access two analog-input cards in a "ping-pong" type fashion with LabVIEW 7.1.
The two cards are PCI-6052E DAQ cards (call them "B" and "C"). What I'd like to do, is get data in this fashion: B/ai0, C/ai1, B/ai2, C/ai3, B/ai4 ..... etc. However when I try to do this I get this error :
"Error -200558 occurred at DAQmx Create Channel (AI-Voltage-Basic).vi.
Possible reason(s):
One task cannot contain multiple independent devices.
Create one task for each independent device.
Device: B
Device: C"
So my question is, IS there a viable way to do this? I have attached my .vi that contains the trouble. Any help would be GREATLY appreciated! Thanks!
Attachments:
Surrogate.vi ‏251 KB

One task cannot span multiple devices. Your problem is that your physical channels in DAQmx Create Channel reference two different devices. You cannot create tasks like that. If you want to ping pong between devices, you'll have to do it with single point reads like this:
B/ai0 >> DAQmx Read Single Channel Single Sample
C/ai1 >> DAQmx Read Single Channel Single Sample
etc...
Hope this helps.
Regards,
Erin

Need for sugestion about DAQ Card for load cell

Hi.
I have a AT-MIO-16XE-50 DAQ card. But, I guess it doesn't work with load cell since it dosen't have output. So I need your regomendation about what DAQ card I should use. Also, if I need to use strain gage conditioner, recomende to me.
Thanks
Jee

I couldn't find any information about a DAQ 512, but I did find info about a DAQCard-512 and DAQCard-500. If you meant one of these boards, then you will need NI-DAQ 6.9.3. That is the latest version of NI-DAQ to support these boards. Post again if you need additional assistance.

Are there any examples for using a CAN card via XNET on a real time system?

I am programming a real time application and I have a PXI 8512 card. My first order of business is to get 5-byte messages from transducers that are broadcasting at 10 Hz on known message IDs. There are no CAN/XNET samples in my "realtime" CVI sample folder. I have found some in the nixnet folder but they are Windows based so I have to hack a lot of stuff out of them.
Thank you.
Michael Chadwell
Department of Engine and Vehicle R&D
Southwest Research Institute

In other words, I just need to do something very similar to this with no user interface:
NOTE: See attachment
Michael Chadwell
Department of Engine and Vehicle R&D
Southwest Research Institute
Attachments:
CAN Bus Monitor.jpg ‏83 KB

How to use the "Clear PDA Chart .vi" in LabVIEW 7.1 PDA module?

In my iPAQ application, I try to use the LabVIEW 7.1 PDA module's "Clear PDA Chart .vi" to clear the graph. But I do not know how to do it. I always get error when I call it.
My code is attached. The code is to draw a sin wave and then clear it.
Attachments:
sin.vi ‏69 KB

Hi,
I verified the behavior that you reported. I got error code 260055065 on running the VI. It does not matter if you wire a control ref or tabbing order number to the Clear PDA Chart.vi.
This is a known bug and LabVIEW PDA developers are already working on it. Hopefully it will be fixed in the next release of the PDA module. Thanks for bringing this to our attention.
Regards,
Ankita A.
National Instruments

Upgraded to 8.2.1 now I have a version mismatch for the PDA module ver. 8.2

I just recieved a new laptop. I installed LV 8.2.1, then PDA module 8.2. Programs will not build. I get a "Mismatched Versions of Labview and the PDA module" error. Help.

Hello,
I was able to reproduce this version mismatch error on a test PC with LabVIEW 8.2.1 and PDA 8.2. This is expected behavior. Also, Matt called in on the phone, and I directed him to his internal sales representative to be shipped 8.2.1 of the PDA module.
I suspect the reason why I was not encountering this on my own PC was that I had already upgraded my LabVIEW Touch Panel Module to 8.2.1 but not PDA yet.
For all people reading this, the ultimate answer is that the PDA version number should match the LabVIEW version number.
Best regards,
-Sam F, DAQ Marketing Manager
Learn about measuring temperature
Learn how to take voltage measurements
Learn how to measure current

Anyone worked on LabVIEW PDA module for Pocket PC?

LabVIEW 7.1 PDA Module is claimed having the new features:
* DMM support for helps you build portable instruments using a PDA
* Tab controls, graph zoom, and additional control customization improve development of professional applications for PDAs
Does anyone has any working example for the ZOOM and for DMM4050? The NI website's example for DMM does not work for LabVIEW 7.1 PDA Module.

Installing the driver for the NI PCMCIA-4050 is a little more complicated than other installations. You will have to follow the exact procedure stated in the "NI 4050 for PDA Readme.htm" file. I pasted the important information here:
Installing PDA files:
Place nirlpdriver.dll and NI4050DLL.dll in the \Windows directory
Place the NIRLP 4050.exe in the \Windows\Start Menu directory
Installing LabVIEW support:
Copy the LabVIEW\NI4050 folder into the C:\Program Files\National Instruments\LabVIEW 7.1\vi.lib\PDA folder
Copy the ni4050.mnu file into the C:\Program Files\National Instruments\LabVIEW 7.1\user.lib folder
Installing LabVIEW examples:
Copy the LabVIEW\Examples\NI4050 folder into C:\Program Files\National Instruments\LabVIEW 7.1\examples\PDA
Getting Started
Before the NI-4050 will be recognized by the PDA, you must run the NIRLP 4050.exe. This EXE will install the registries needed by the PDA to recognize the hardware as well as a test routine which allows you to verify that the device is properly installed.
Once the device has been tested, you are ready to begin building your own LabVIEW PDA application with the NI-4050.
If you are new to developing PDA applications with LabVIEW, read the LabVIEW PDA Module User Manual.pdf for getting started. You can find the manual by going to Start>>Program Files>>National Instruments>>LabVIEW 7.1>>Module Documents>>LabVIEW PDA Module User Manual.
There are several examples which come with the NI4050 for PDA. You can find these examples in the C:\Program Files\National Instruments\LabVIEW 7.1\examples\PDA\NI4050 directory.
When building code for your PDA which includes the NI4050, make sure to manually add the NI4050DLL.lib file in the LabVIEW 7.1\vi.lib\PDA\NI4050\Include directory. To do this, in LabVIEW go to Tools>>Build for PDA and then select the “Source Files” tab, press the Add File button and browse to the NI4050DLL.lib file.
Without these actions, your application will not work. Make sure that you install the NI PCMCIA-4050 driver AFTER an optional NI-DAQmx Base install.
Please let me know if you are still having issues after following all the directions from the readme-file.
- Philip Courtois, Thinkbot Solutions

How to setup PDA module for wince

I want to develop a PDA that with some measurements or analyze function, so i choose the Labview for PDA module.
My hardware is ARM s3c2440(Samsung), OS is WinCE5.0. Software: LabView7.1
I have developed the VIs for PDA module on the Pocket PC. I remember that I had to install EVC++ and Pocket PC SDK before I setup the PDA module.
So I thought after I installed the EVC++ and the SDK for my 2440 board, I could setup the PDA Module as before. However, I found that the installation still have to find the Pocket PC SDK.
How can I setup the PDA module with my 2440's SDK?
Another question, can I develop the Labview PDA module in the enviroment of ARM s3c2440+embedded Linux(qtopia)?
Thanks for have read this question, waiting for your guides.

Depending on how the clients connect use the IPv6 prefix of their 6to4, Teredo, and/ or IP-HTTPS tunnel. Just keep in mind that it could become a long list...
My Blog: http://www.petervanderwoude.nl/
Follow me on twitter: pvanderwoude

Do I need to use DAQmx Base for PDA module or DAQmx will work just fine?

Hi All,
Does PDA module work only with DAQmx Base or DAQmx as well?
hellolv

Hi hellolv,
The PDA module currently only works with DAQmx Base. If you've never used DAQmx Base before, it is actually very similar to DAQmx, and there are lots of examples out there to get you started. I recommend searching through our Example Code Library.
Thanks,
Justin M.
National Instruments

Daq down counter example for pci-mio-16e-4 wanted

Hi!
I am searching for an example vi of a down-counter for
ttl pulse trains.
thnx,
Holger

Thanks for that, but that was also my first idea. Unfortunaly there is no
example for an DOWN counter in that directory. they all count up.
i want to count incoming a ttl-pulse-train and terminate that train(by
dio-line) when
counted exactly a certain number of counts. if i check the counts (600Hz)
each time by software, there seems to be no chance to terminate the train
at the desired number of pulses and thatfore i will have to use the daq card
on board counter. and my idea is, that a down counter (which is specified in
the
manual) would do it.
my question therefore is, if anyone has ever used a DOWN counter, because
i have no idea how to realise it/how to use the daq-included down-counter
vi, which
i don´t realy understood
i am thankful for any reply!
bes
t regards,
holger
"Nirmal Sharma" schrieb im Newsbeitrag
news:[email protected]..
> Hi,
> there are numerous examples which you can find at this path:
> C:\Program Files\National Instruments\LabVIEW 6.1\examples\daq\counter
>
> or Goto Find examples in Labview launching Panel -> Hardware Input and
> Output -> DAQ -> Counters
>
> If you are using DAQ card, Goto ->Count buffered edges or count Edges.
>
> Hope this works. Your feedbacks are welcome.
>
> Best Regards,
> Nirmal Sharma

In the NI-5640R Instrument Driver API Examples for the Modulation Toolkit what is the mode of operation of the DAC/DUC(AD9857)

In the NI-5640R Instrument Driver API Examples for the Modulation Toolkit what is the mode of operation of the DAC/DUC(AD9857)

In the single tone mode AD9857 would not take any digital data. It ganerates the sinusoidal wave using DDS present inside.
Message Edited by Vinny ICS on 05-25-2009 05:04 AM

Error for LabVIEW PDA Module Version 8.5

Hi all
I am face on with problem when i try to do the LabVIEW PDA Module Version 8.5 Tutorial which is include in labVIew software package.All my lincence status also activated and do install all the accessories that i need.I follow all the steps by tutorial sheet.But i still face on with problems, so now i would like to uninstall my LabVIEW software and reinstall again.The error is as shown in attach file. i want to know is there any problem if i uninstall my software? If anyone can show me why the error is? The technician said even though the error come out, just close and wait for about 5 min.After 5 min already the emulator will be come out.But mine haven't comeout.So please any one can show me?
Thanks a lot
Best Regards
Nyan Lin
PS: The tutorial that i do is as shown in attach file.
Attachments:
PDA_Getting_Started.pdf ‏452 KB
error14.JPG ‏119 KB
error8.JPG ‏131 KB

Hi Stephan
Thanks for giving your time for me. I am a new LabVIEW PDA Module user.And I have to do it because of my final year project.I am student from Nanyang Polytechnic (Singapore). I never use labVIEW software and LabVIEW PDA Module software before.This is my first time. The software that i have is LabVIEW Version 8.5. So as what you say is i need to reinstall my the whole LabVIEW PDA Module and all start again? Then i know that for PDA Module i need to download Virtual PC2007.But what else i still need to install? The Window Mobile 5.0 emulator and the rest softwares is it include in the LabVIEW PDA Module software package? If not, please let me know which software i still have to download? Then i go and check the software status that i have and the lincense status is as shown in attach files.Thanks for giving your time and help me.
With Regards
Nyan Lin
Attachments:
Software status.JPG ‏72 KB
Lincense.JPG ‏98 KB

Pda module - ao examples for 6024 E daq card

Similar Messages

Maybe you are looking for