Ports for applications (RTMT,CIPC ect)

Hi all,
I need to open ports in vpn connection for CIPC ,RTMT , historical reporting, and Jabber .
Anyone knows which port I need to open ?

Table 6 Signaling, Media, and Other Communication Between Phones and Cisco Unified Communications Manager of the following link provides the port usage details
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/port/10_0_1/CUCM_BK_T537717B_00_tcp-port-usage-guide-100/CUCM_BK_T537717B_00_tcp-port-usage-guide-100_chapter_01.html
For RTMT, 8443 is the port that the application will use to listen to the server by default. However, it is configurable as per the RTMT admin guide
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/service/8_0_1/rtmt/RTMT/rtinst.html
HTH
Manish

Similar Messages

Open port for application

Hi
I have just installed Yosemite OS X 10.10.1 and realised one of the application stopped synchronising data with my iPhone 4. I have asked the technical support for help and been told that application needs Bonjour and ports from 49152 up to 65535 to work. I have used Network Utility and found out that ports are blocked and nothing get through to my router. This is why applications on iPhone and Mac cannot see each other.
I have tested syncing by temporally disabling the firewall in Mac and applications eventually got connected.
My question is, how to open, if I can, a specific range of ports for an individual application in Mac? In future, I would simply like to avoid disabling the firewall as not very secure work around.
Kind regards.
Zb

Why do you even have the firewall enabled? If you have NAT enabled to distribute local IP addresses, then you don't need the firewall unless you are being specifically attacked/hacked.
You would need to specifically open ports via Airport Utility or remove whatever you are protecting from the firewall.

Why does port scan show an open port for application I've never had?

I don't currently and never have used Bacula to backup my Macbook, but for some reason when I do a portscan it often shows a Bacula file daemon being open on port 9102. It also comes up in Netstat as listening, even with my firewall blocking all unnecessary connections, sharing turned off (all), and an Airport ex in front of it also secured. I also cannot find any related files etc. on my machine after a thorough search. Despite my best google and support searches, I couldn't find anyone with the same problem. Is this reason for concern? Either way why would it be there despite it not being ever used on my Mac? I am not well versed in networking, only know enough to get myself in trouble, so thanks in advance for any help.

Ok, I ran a port scan on 9102 and it show it's not responding, but assigned to (bacula-fd)
So what it appears to be is Bacula ( a legitimate program) uses this port, much like Screen Sharing uses port 5900, not necessarily that it's installed on your machine.
It's not uncommong to have open ports, it's so if you ever install the program or use a service it can gain access through the Firewall. You can change that of course to close up everything except certain ports for certain programs.
Now that the firewall is App based, if you don't have the app listed, how do you deny it access?
Well if the program isn't installed on the machine, it can't respond if the port is open or closed.
Simply enable your Firewall and allow the programs you do have and want to access your machine to connect in the Advanced settings.
There is also NoobProof and WaterRoof if you need a GUI/simplicity to enact more complex features of the command line firewall. Block IP addresses and everything. However read up before you mess around, Apple has everythign set up nicely and there are very few successful attacks on Mac's.
If you don't know what your doing, you can actually do more harm opeing up your machine to poential attack.
If your more paranoid, then install LittleSnitch, it's a outgoing firewall and notification software with pop-up window to allow/deny on a per program or request basis. You'll be quite shocked how much is going out in the background without your knowledge.

Connection ports for Applications

Hi everyone
I have a question, we are installing BO but the consultants are connected via VPN, we have communications issues and I don't find the ports for:
WebIntelligence
Dashboard Desing (Crystal Xcelsius)
Information Desing Tool
Someone knows where can I find the ports?
Best regards

Hi Gilberto,
I'm assuming you're still getting this issue...
You'll need to lock down a number of the Processing servers in the CMC, so that they use a specific port. Once this is done, then you'll have to open those ports on the firewall.
The following servers will need the request port, as it's called, setting in the CMC:
CMS - Uses 6400 for the initial handshake
Input/Output FRS
Webi Processing Server
Dashboard servers
I'm assuming that you are using BI 4.x, so you will also need to set the request port for the Adaptive Processing servers that you should have split out.
If this doesn't work, then it could be something that denied/stopped via the VPN, i.e.: if you use a jump server or something along those lines.
Let me know how you get on.
Cheers,
Kevin

AIX 5.3 to 6.1 Upgrade (32 to 64 bit porting for application)

Hi,
We are facing a porting issue while trying to compile a binary as 64 bit using the 64 bit Oracle client library.(libclntsh.a).
Warning while linking with the 64 bit library is as below:-
(ld): resolve
ld: 0711-228 WARNING: Duplicate symbols were found while resolving symbols.
The following duplicates were found:
Symbol Source-File(Object) OR Import-File{Shared-object}
.bcopy {apps/oracle/product/11.2.0/client_1/lib/libclntsh.a[shr.o]}
** Duplicate ** moveeq.s(/usr/lib/libc.a[moveeq_64.o])
Kindly suggest a solution for the above asap.
Regards,
Dipjyoti Ghosh

Hi,
Finally got the solution for the problem faced.
Since many of the system calls viz : memcpy,strcpy internally use the bcopy function which is part of libc.a as well as libclnstsh.a.
Hence re-ordering the compiler flags for libraries putting -lc before -lclnsth resolves the issue since the bcopy is able to resolve its definition to libc.a.
One more similar issue is related to functions present in libCrt.o which result in undefined symbols incase the flag -brtl is being used along with libclntsh.a library of oracle.
In this case removing -brtl flag resolves the issue. -brtl is not used in cases compilation is clean and used incase undefined symbols are found
at runtime. More about this flag can be found
@ http://publib.boulder.ibm.com/infocenter/comphelp/v7v91/index.jsp?topic=/com.ibm.vacpp7a.doc/compiler/ref/ruoptbrt.htm
@ http://en.wikipedia.org/wiki/Runtime_library
@ http://www.fortran-2000.com/ArnaudRecipes/sharedlib.html
Thanks Deependra for your inputs.
Thanks and Regards,
Dipjyoti Ghosh

How to forward/open ports for WRT54G?

Hi. I recently bought a WRT54G because my old router was destroyed by lightening and thunder. I have managed to set it up, and got the interent itself to work with static IP adress (192.168.1.101 for my PC).
However, even though I have tried to forward/open ports for applications like uTorrent and DC++ as well as Limewire, I have no luck. When I test if the ports are indeed opened, I get the result that they are not. Here are how my port forward setting looks like for utorrent. The port in the settings image is of course the same as in uTorrent.
http://www.pictub.com/quickupload/01/untitled-1mb4wd.jpg
I can't seem to open any ports, even though I have followed tutorials like the ones at portforward.com. I have the latest firmware for my router, as I flashed it when I got it. Help .

Yes, I did .
Anyways, look what I found in the uTorrent FAQ:
1.7 Special note for users with Linksys WRT54G/GL/GS routers, there are severe problems with them when running any P2P application
To fix it, they say one has to flash with a unofficial firmware, but I will rather get the money back and buy another router tomorrow. Thanks for the help anyways .

APEX SSO and Load balancing: Could not determine workspace for application

We had a single HTTP Server serving APEX in a 10.2.0.2 database configured with SSO to be used by the developers. APEX has been registered as a partner application and the login url has been CA Siteminder protected so that the SM_USER details are forwarded in the header for the application to use for authorization. Everything is fine so far.
Now we have added a HTTP Server on another host and have it all set up for APEX and its pointing to the same database. APEX_ADMIN access works as normal, but applications previously using SSO now get the following error after entering the URL.
Expecting p_company or wwv_flow_company cookie to contain security group id of application owner.
Error ERR-7620 Could not determine workspace for application ().
Using HTTP Watch I find that the application is not even trying to redirect to the login page.
What is wrong here?

APEX has been registered as a partner application as described in
http://www.oracle.com/technology/products/database/application_express/howtos/sso_partner_app.html
In the meantime I found metalink document 368746.1 which describes the cause of this problem. Please read carefully what I wrote, it all works when the the new APEX web server is turned off in the server farm on the load balancer and directed through the original web server. When running regapp.sql the hostname in the listener token was using the virtual hostname. This works fine if the request comes from the original APEX server which proofs that there is nothing wrong with the installation and set up of SSO. When directing the request to the new APEX web server the APEX_ADMIN page still works only existing work spaces using SSO don't seems to work anymore resulting in a error as described in the subject.
As for metalink document 368746.1 naming the causes of this error:
- there are no duplicate entries in WWSEC_ENABLER_CONFIG_INFO$
-LISTENER_TOKEN clearly works for requests coming from the first web server
-theoretically the web server listener port could be changed from 7777, but port 80 needs to be maintained here as production is mimiced as far down as possible.
Is there some cache table which can be cleared? How is it that the flows schema (apex engine) can not find the work space when the request comes from a new web server which can however access the APEX_ADMIN pages.
anyone?

Open ports for all in LAN

Hi, a few days ago I bought a wireless router WRT160n. I want to ask how to open some port for all in LAN(3 clients). For example all in LAN have PeerToPeer application for torrents. I want to open port for example 20202 for all. Now I open port from menu Applications & Gaming->Single Port Forwarding, but I must set port for each user IP address.
Can somebody tell me how to open port for all in LAN without to config for each computer?
Thanks in advance.

Hi gv. I read more about UPnP and the WRT160n User Guide. In section Administration>managment int wrote that UPnP is Enabled by default in my router it is corect. I Setup mu PeerToPeer(eMule) TCP/UDP ports to 20202 and check option "Use UPnP to setup ports". I test and close this port on my router configuration for my computer on "Single Port Forwarding", but in eMule the port is still block. Can you explain why it did not work. For UPnP it says that if Enable it allow users with Windows ME and XP automatically to gonfigure Router ports
Thanks in advance!
Best Regards.

Forwarding port for Counter-strike: Source is not working

With my linksys router (Model WRT54G)I tried forwarding my port for a Counter-Strike: Source server. My friends tried it after I tried forwarding the ports and it did not work. It looks like this: |Application|Start|End--|Protocol|Ip-Adress------|Enabled| |CS1--------|1200-|1200-|Both----|192.168.1.[105]|Check--| |CS2--------|2700-|27015|Both----|192.168.1.[105]|Check--| |CS3--------|27020|27039|Both----|192.168.1.[105]|Check--| I can get on the server but my friends can not. And yes, I did uncheck "Block Anonymous Internet request". Message Edited by Iridium on 08-16-2007 07:37 PM Message Edited by Iridium on 08-16-2007 07:38 PM
Message Edited by Iridium on 08-16-2007 07:38 PM

Is the IP address 192.168.1.105 really the IP address of the server in your LAN?
Moreover, check what kind of modem you have. Follow the instructions here. If the IP address on the status page is a private IP address and the IP address on whatismyipaddress.com is different then your modem does routing too and you have to configure port forwarding there as well.

Connection to serial port for communication RFID

HI,
I have occurred problem in communication to serial port for accessing the RFID
through Serial Port COM1 or COM2 . I got garbage values of Card .
Please give me the code for accessing serial port and indicter the cadr is detected by RFID and read the data on card.

EHAG microchip 13,56 MHz dual reader and Mifare 1KB contactless smartcard.
I've succeed to retrieve the data from the transponder (card) but it just only once when i click the button from my application. My question is how do i retrieve the data continuously from the card for every few milliseconds?
sorry for my language.

Creating new logical ports for WSDL with several port types not working

Hi all,
I am trying to integrate some BODS webservice into the BPM. I am using CE 7.2 Kernel Version: 7.20.3710. When I am trying to assign a provider system in the application configuration I get following error:
The provider system successfully found the needed service, but its wsdl is without webservice policy. Thus the generated client configuration might not work because of different configurations between service and client (most probable a difference in the security settings). Either assign a provider system with access to wsdl with policy or manually create the client configuration.
The regarding provider system is using a communication profil where the authentication method is set to "none". Normally this configuration should work, but it isn't.
So I started to create new logical ports for each port type. But then I get the error:
Port type name of loaded WSDL does not match the port type name of the Service Reference.
I checked already the port type names in the WSDL but they are 100% the same. What I found was that the configuration is always trying to use the first port type in the WSDL. So I am not able to configure the other port types in the service group.
I also tried to do the same thing using a WSDL with just one port type and surprise it is working...
I hope somebody can help me out
Thanks in advance
Andy

Hi Andy,
Please check this Link: https://cw.sdn.sap.com/cw/docs/DOC-45012
Regards,
Naresh B

Inconsistent prob when adding listeners to serial ports for sending AT cmds

I have an app that sends and receives SMSs from two different cell phone carriers (lets say verizon and sprint by example).
For that matter i have two cell phones, exactly the same model, one from each carrier, connected to the PC serial ports, COM, COM6 and COM7 being aware that they are available.
-The application communicats with the phones through the a serial communication API and sending AT commands.
-The application can send messages correctly from both phones within the same transaction, this is, i click in send message and the message is sent from both phones.
The problem is when receiving, getting the SMS received by the phones:
-When i have ONE phone connected to the PC it work properly for both phones.
-When i have BOTH phones connected, only Carrier1 phone receives properly.
When checking, i just find out that the problem rises when i try to add the listeners (see code comments below).
When both phones connected there seems to be a problem that i cant figure out, and may be its a conceptual misunderstanding from me.
I attach the code if you can help me,
thank you,
fernando
// class fields
private static String PORT_CARRIER1;
private static String PORT_CARRIER2;
private static CommPortIdentifier portId;
private static Enumeration portsList;
private static SerialPort carrier1SP;
private static SerialPort carrier2SP;
private static InputStream carrier1_input;
private static InputStream carrier2_input;
private static OutputStream carrier1_output;
private static OutputStream carrier2_output;
// ... all the code below is from the app method where everything is initializated
portsList = CommPortIdentifier.getPortIdentifiers();
while(portsList.hasMoreElements()){
     portId = (CommPortIdentifier) portsList.nextElement();
     if(portId.getPortType() == CommPortIdentifier.PORT_SERIAL){
          // try to open ports
          try{
               if(portId.getName().equals(PORT_CARRIER1))
                    carrier1SP = (SerialPort) portId.open("SMS", 5000);
               else if(portId.getName().equals(PORT_CARRIER2))
                    carrier2SP = (SerialPort) portId.open("SMS", 5000);
               else System.out.println("Error " + portId.getName());
          }catch(PortInUseException piue){
               System.out.println("Exception while opening serial ports: "+piue.getMessage());
               continue;
          // try to open input streams
          try{
               if(portId.getName().equals(PORT_CARRIER1))
                    carrier1_input = carrier1SP.getInputStream();
               else if(portId.getName().equals(PORT_CARRIER2))
                    carrier2_input = carrier2SP.getInputStream();
          }catch(IOException ioe){
               System.out.println("Exception while opening input streams: "+ioe.getMessage());
               continue;
          // try to open output streams
          try{
               if(portId.getName().equals(PORT_CARRIER1))
                    carrier1_output = carrier1SP.getOutputStream();
               else if(portId.getName().equals(PORT_CARRIER2))
                    carrier2_output = carrier2SP.getOutputStream();
          }catch(IOException ioe){
               System.out.println("Exception while opening output streams: "+ioe.getMessage());
               continue;
          // adding listeners
          try{
               if(portId.getName().equals(PORT_CARRIER1))
                    carrier1SP.addEventListener(new ListenerPuerto(this, carrier1_input, "CARRIER1"));
               else if(portId.getName().equals(PORT_CARRIER2))
                    carrier2SP.addEventListener(new ListenerPuerto(this, carrier2_input, "CARRIER2"));
          }catch(TooManyListenersException tmle){
               System.out.println("Error while adding listeners: " + tmle.getMessage());
               continue;
          // Adding specific event to listeners
          if(portId.getName().equals(PORT_CARRIER1))
               carrier1SP.notifyOnDataAvailable(true);
          else if(portId.getName().equals(PORT_CARRIER2))
               carrier2SP.notifyOnDataAvailable(true);
          // Setting params to serial communication
          try{
               if(portId.getName().equals(PORT_CARRIER1)){
                    carrier1SP.setSerialPortParams(9600, SerialPort.DATABITS_8, SerialPort.STOPBITS_1, SerialPort.PARITY_NONE);
                    carrier1 = true;
               }else if(portId.getName().equals(PORT_CARRIER2)){
                    carrier2SP.setSerialPortParams(9600, SerialPort.DATABITS_8, SerialPort.STOPBITS_1, SerialPort.PARITY_NONE);
                    carrier2 = true;
          }catch(UnsupportedCommOperationException uscoe){
               System.out.println("Error while setting params for serial communication: " + uscoe.getMessage());
               continue;
          // ... nothing else important ...thanks in advance

Thinking of a java application as its what I am most
comfortable with, but also thinking of having an
apache server, and using jsp pages or servlets...
because I hate formatting things in a java frame..
have never quite mastered that! Any thoughts on what
I should use?I'd prefer a Swing GUI for a maximum of controls. If you have any problems regarding layout, you can post concrete questions here (or even better: the Swing forum).
And my main stumbling block would be how do I send
signals to the green light from the computer? How do
I get signals from the light beams to the computer?
How do I use a serial port (for eg) from a java app.There's an additional library for serial I/O, it's named javax.comm ... should be downloadable somewhere on the java.sun.com site.

What is the best way to port complete applications from DEV - Test - PRD?

Hi,
One of my customers recently asked me, Supposing I do the complete integrations and modelling in SOA Suite on the DEV Environment. Then,
What is the best way to port complete applications from DEV -> Test -> PROD ??
Also, since the URLs in use in the DEV environment would be very different from other environments, what is the easiest way to maintain them, and to build in Access Control mechanisms ?
Best Regards

Hi AJ,
Nice PDF !
Though the PDF does give a basic idea as to how we can go about the deployments using ANT and EM in Test and Prod, it doesn't really give extensive details. For eg. ANT would obviously need huge ANT scripts to be written for migrations to multiple Test servers, etc.
Similarly, when we talk about EM, does it mean each of the services has to be manually deployed on Production ?
I am sure we would be looking more towards a fully automated solution. No ?
Best Regards
Nitin

What is the best way to port complete applications from DEV - Test - PROD

Hi,
One of my customers recently asked me, Supposing I do the complete integrations and modelling in SOA Suite on the DEV Environment. Then,
What is the best way to port complete applications from DEV -> Test -> PROD ??
Also, since the URLs in use in the DEV environment would be very different from other environments, what is the easiest way to maintain them, and to build in Access Control mechanisms ?
Best Regards

It has been discussed here in detail-
SOA 11g Composite Deployment across multiple Instances: Best Practice
since the URLs in use in the DEV environment would be very different from other environments, what is the easiest way to maintain them, and to build in Access Control mechanisms ?You may use deployment plan for this purpose. For access control, you may use Role Based access of Weblogic and EM. Please refer -
http://download.oracle.com/docs/cd/E17904_01/integration.1111/e10226/appx_roles_privs.htm#BABIHDFJ
Regards,
Anuj

Port for uTorrent - WRT54GC

Hi,
I need one more help.
I want to release ports for uTorrent.
I have a WRT54GC router.
I successfully logged in, and clicked on Applications and gaming, and I think there I should typed ports in the tab Port range forwarding.
Since I'm not good at that stuff, and it's my first time doing it. I want to know what numbers are for Start and End port for uTorrent, or where can I find it. I have uTorrent 2.0.3 and I only found the current port (for incoming connections) in Setup guide. In Preferences and elsewhere I didn't find anything with 'port' in it.
As for the Protocol I would go both (TCP and UDP), IP address is the same, and will check Enabled. I only don't know the Start and End port.
Thanks in further and I appreciate the help!
Thanks,
Aleks
Solved!
Go to Solution.

Or should go on the tab Port range triggering. If so, what are the numbers of Triggered range and Forwarded range?

Ports for applications (RTMT,CIPC ect)

Similar Messages

Maybe you are looking for