POS Interface

Hi Friends
I am working on Batch Valuation. Using Standard IDOC WPUUMS for sales posting from POS. The standard IDOC do not have Batch field and In have enhanced it to insert batch number in article and billing documents. But still batch number is not getting updated for the purpose of cost price that is condition type VPRS. Standard sales order, delivery and billing process is picking batch level cost price. Can you please let me know any exit for sales inbound processing which can pass batch number in standard table MBEW to get correct valuation for VPRS during inbound processing.
Regards
Gautam Anand

Hello,
The standard POS interface idocs do not include the batch number because it is not relevant nor necessary for the POS sale transactions however, The batch number could be included using an enhancement segment.
Idoc type WPUBON it is possible to have the batch number using E1WPB02-SERIENNR, after which userexit "EXIT_SAPLWPUE_102" can be used the field e1wpb02-seriennr into g_t_imseg-charg. Using the enhancement
segments for WPUMMS you should also be able to add the batch number.
Goodluck.
Suhail Shaik

Similar Messages

Handling of Down payments / advance payments retail POS interface

Hi all,
Does anyone know if there´s a best practice to handle down payments with POS interface?
thanks in advance
Mariana

Hi Mariana,
Pl use the following link:
help.sap.com/bp_retailv1470/documentation/EN/Store%20Business%20Offline%20EPOS_EN_PRES_V147.ppt
IDOC for down payment is WPUTAB01.
Entries will be as follows:
If a customer is making a down payment of Rs.1000/-
Cash a/c DR 1000/-
Customer or Site CR(Retail Stores if u dont maintain individual customers) 1000/-
When sales are closed say for example Rs.10000/-
Cash a/c DR Rs.9000/-
Customer or Site DR Rs.1000/-
Sales CR Rs.10000/-
In SAP u need to create a Special G/L with Indicator A and this special G/L will be assigned to your main a/c in Tcode OBXR.
F-29 Post Customer Down Payment ,F-32 Clear Customer ,F-39 Clear Customer Down Payment are the FICO transactions which will be used. Pl contact yr FICO
consultant for further details.
Hope this helps you.
Regards,
Mani

POS Interface with SAP

Hi,
We are currently using SAP ECC6.0, not on IS Retail.
As we have quite a few POS machines being used in the business, we would like to interface POS with ECC6.0.
Is there any third party tools available in the market for achieving this solution?
Thanks
Ram.

Hi Ram
SAP offers regarding POS integration to IS Retail basically two options:
- POS DM (see http://wiki.scn.sap.com/wiki/pages/viewpage.action?pageId=113246846)
- classic POS interface direct in ECC (WPUBON/WPUFIB/WPUTAB IDoc's for POS transactions)
You want to interface directly in to a non IS Retail ECC system.
Question is what do you want to interface only financial postings or also goodsmovements?
How are the stores represented in SAP (customers/plants?)
The transaction logs (TLOG) info from the POS should be converted to a IDoc that will represent you functional needs on the ECC side.
For this mapping SAP offers SAP PO (proces orch), formally know as PI (or before that XI).
There are also several middleware solutions from third party vendors that can work with SAP.
In such a tool you have to map the TLOG to the desired IDoc you want to use in SAP.
(IDoc could also e replaced with a BAPI/RFC for instance).
Regards
Bob

POS interface without IS Retail

Hello everyone,
We have ECC6.0 but do not have IS retail. There are some retail business in the organization, so we are trying to build a POS interface with development. Does anyone has experience with that? Does anybody know how the AR should be posted with all the sales data uploaded from POS?
Thanks a lot for the help!

To,
Dear Colleague,
The objective can be achieved by using SAP Middleware and you have to define Business Object, IDOC, BDOC, and sites and you have to activate all parameters as same as in both Source system and Target system,
Also try Groupware, FTP Server, TREX, for further compatibility as per your business process.

POS Interface with no POSDM!! Possible?

My client is planning to implement standard POS interface in IS Retail. I have worked several times with POSDM in order to post the Sales, Financial and Inventory Data into SAP, but all used standard POSDM. The client does not have POSDM license and just wants to post the sales and financial data.
Can this be done with standard POS Interface by posting WPUBON01, WPUFIB01 Idocs straight in IS-R?

Hi Raj,
My client is asking for POS to POSDM integration using SAP standard services (not IDOC or BAPI). You have mentioned using standard in your previous integrations. Can you please provide more information on the POS to POSDM that you have done so far. I have no knowledge in this integration. Any documentation or links that you can provide will be great.
Thanks in advance.
Regards,
Srinivas

Idoc erros.......POS interface.......

Hi All,
Using transaction WPER for POS interface i can see the errors associated with idocs, not processed due to errors. My requirement is to capture same error messages and show in output of my report against idoc number
Can anybody tell me from which table or function module , i can capture these error messages.?
Table EDIDS doesnt contain same error messages.
Regards.

Hi Micky,
Exact error messages showing in WPER can't be extracted from EDIDC and EDIDS tables.....
Regards.

Reg timeslot in POS interface

Hi i have pos oc3c/sdh interface. I would like enable 8 timeslot. can anyone help to do this.
regards,
kamalnath

What sort of device is the pos interface on?

Maximum Bandwidth on ML-1000-2 POS Interface

I have an ML-1000-2 card on Cisco 15454 ONS, I want to set up IP between two ONS with STM-4 SDH between them. I wand to map the STM-4 to the POS interface on the ML-1000-2 card. Will this POS take the STM-4? If yes, what is the maximum STM bandwidth I can map to the POS interface on the ML-1000-2?

I wand to map the STM-4 to the POS interface on the ML-1000-2 card. Will this POS take the STM-4.
Yes you can map STM-4. But u can use only if u have XC-10G cross-connect card
If yes, what is the maximum STM bandwidth I can map to the POS interface on the ML-1000-2
You can map both port to a STM 16 rate. Each port to STM 8bandwidth.
info from cisco
The new Cisco IOS-based ML-1000-2 card is used for Gigabit Ethernet (1000
Mb/s) when the XC-10G cross-connect card is in use. It supports Layer 2 and
Layer 3 services and provides up to 2.4 Gbps of transport bandwidth, software
provisionable in transport bandwidths from 50Mbps to the ports full line rate, in
STS1, STS3c, STS6c, STS9c, STS12c and STS24c.

Check Light Levels on 7300 POS Interface

Is there a way to check the incoming light levels of SM fiber link to a POS interface on the router itself?

Not that I'm aware of. The card itself has the Carrier/Alarm LED that should be Green if/when a valid SONET signal is detected on the incoming line.
To measure the optical power level though, I believe you need to disconnect the fiber and use an Optical Power meter.
The higher end SONET cards (e.g, those used in the 15400 series) have built-in power signal level measurement but then you pay a lot more for those.

Connection between CRS 1 POS interfaces and 7600 POS Interfaces

Hi,
I am trying to connect a CRS 1 POS interface to a Cisco 7609 POS interface and i keep geting the following alarms, and the line protocol i s down on both device ends
RP/0/RP0/CPU0:at_crs_01#LC/0/2/CPU0:May 1 10:42:47.363 GMT0: spa_oc48[245]: %L2-SONET_LOCAL-4-ALARM : SONET0/2/0/2: SLOS cleared.
Please help!!
Attached are the configurations on the Devices

Hello Obiora,
if the two are connected in back to back: one side provide the clock with
clock source internal
the other side should take the clock from line
clock source line
I would change one of the two in clock source line
Hope to help
Giuseppe

POS interface using JCo

Hello,
We're currently developing a JCo based interface to integrate a java based POS with SAP ERP. What are the relevant BAPI's to be used in order to implement an inbound (upload sales data) and outbound (download article data and prices) interface?
Thanks in advance for your response.

Hello,
We're currently developing a JCo based interface to integrate a java based POS with SAP ERP. What are the relevant BAPI's to be used in order to implement an inbound (upload sales data) and outbound (download article data and prices) interface?
Thanks in advance for your response.

Profitability analysis activated in POS Interface, performane/tuning issue?

We are about to golive with a SAP retail system. All purchases made by customers in store are sent into SAP via and idoc via the so called POS (point of sales) Interface.
A reciept received via an idoc creates material docs, invoice docs, accounting documents, controlling documents, profit center docs and profit ability analysis documents.
Each day we recive all receipt from each store collected in one idoc per store.
When deactivate our profit ability analysis an average store are posted in about 40 seconds with sales from an average day. When we post and profit ability analysis are activated the average time per store are almost 75 seconds.
How can simple postings to profit ability analysis increase the posting time with almost 50 %? Is this a performance/tuning issue?
Best regards
Carl-Johan
Point will be assigned generously for info that leads to better performance!

which CO document does the system creates : CCA document ?
on which cost centre ? PCA document ?
What is the CE category of the CE used for posting the variance ?

Change Remote Hostname on POS Interface

Hi,
After exaust search on the internet about how to change the Remote hostname feature on the Path Trace Buffer (J1), I didnt find the solutions. The Concern is that my customer want to See on their side with do show controller the Remote Hostname as other End Hostname, and not the PE locally connected to him.
Can anybody please help me to figure out this in order to hide the MPLS PE structure and let the CE's see each other Remote Hostname and other Remote features to be the order remote CE, instead of local PE? Eventually this is to emulate pure SDH over MPLS.
Please help.
PE-1#show controllers pos1/0
POS1/0
SECTION
LOF = 0          LOS = 0                            BIP(B1) = 0
LINE
AIS = 0          RDI = 0          FEBE = 0          BIP(B2) = 0
PATH
AIS = 0          RDI = 0          FEBE = 0          BIP(B3) = 0
PLM = 0          UNEQ = 0
LOP = 0          NEWPTR = 6625       PSE = 9517        NSE = 0
Active Defects: None
Active Alarms: None
Alarm reporting enabled for: SF SLOS SLOF B1-TCA LAIS LRDI B2-TCA PAIS PLOP PRDI B3-TCA
Path triggers active (no delay)
Framing: SDH
APS
COAPS = 0          PSBF = 0
State: PSBF_state = False
Rx(K1/K2): 00/00 Tx(K1/K2): 00/00
S1S0 = 02, C2 = 16
CLOCK RECOVERY
RDOOL = 0
State: RDOOL_state = False
PATH TRACE BUFFER: STABLE
Remote hostname : blad810
Remote interface: POS7/1/0
Remote IP addr : 57.35.27.113
Remote Rx(K1/K2): 00/00 Tx(K1/K2): 00/00
BER thresholds: SF = 10e-3 SD = 10e-6
TCA thresholds: B1 = 10e-6 B2 = 10e-6 B3 = 10e-6
Clock source: line
Cheers.

Fabric ping timeouts occur when the Gigabit Route Processor (GRP) detects that a ping request is stuck in the ToFab queue (towards the switch fabric) of the Cisco Cell Segmentation and Reassembly (CSAR) application-specific integrated circuit (ASIC). This ASIC is responsible for slicing the packets into Cisco Cells before sending them through the switch fabric to the output line card (LC). Fabric ping failures occur when either a line card or the secondary GRP fails to respond to a fabric ping request from the primary GRP over the switch fabric.
http://www.cisco.com/en/US/products/hw/routers/ps167/products_tech_note09186a00800943b2.shtml

SAP Retail - XI - POS Interface

Hi,
Can anybody share the document of
SAP Retail - XI - POS(Point of Sale)
Here POS is the third party system
Thanks in advance,
Balaji

Hi,
Check these for Retail-POS
https://websmp109.sap-ag.de/~sapidb/011000358700001136952007D/MasterGuide_Retail_Dec07.pdf
http://help.sap.com/erp2005_ehp_03/helpdata/EN/12/08414a470311d1894a0000e8323352/frameset.htm
Regards
Seshagiri

Does DPT card support normal POS interface.

we have a DPT ring , router is GSR12016, DPT card is 1-Port OC-48c/STM-16c long-reach/OC48/SRP-LR-SC-B=.
recently we want to remove the ring,we want to reuse this DPT card, but we don't have enough DPT card, we have normal POS (SDH)card, can we connect this DPT card to normal POS card(don't support DPT ring).
Thank you!
Tom

POS and DPT work in different way so cannot connect a DPT card to POS card which doesnot support DPT.

POS Interface

Similar Messages

Maybe you are looking for