Possible dead battery on late 2007 MacBook white?

Yesterday my girlfriend put her late 2007 MacBook (running 10.5.1) to sleep and when she went to wake it up it would appear to have died/shutdown and then tried to start up. There was a whir of the DVD drive and then it started to play the boot sound and then just cut out.
On further attempts to boot it (from battery) now does the same thing. Though if the power is plugged in then it starts OK. I've tried an SMC reset, but that doesn't appear to have helped.
The MacBook was purchased in December 2007. Current battery info is as follows:
Battery Information:
Model Information:
Manufacturer: DP
Device name: ASMB016
Pack Lot Code: 0002
PCB Lot Code: 0000
Firmware Version: 102a
Hardware Revision: 0500
Cell Revision: 0200
Charge Information:
Charge remaining (mAh): 3310
Fully charged: No
Charging: Yes
Full charge capacity (mAh): 4019
Health Information:
Cycle count: 285
Battery health: Good
Battery Installed: Yes
Amperage (mA): 1073
Voltage (mV): 12535
Does all this point to a dead battery?
Cheers,
Jay

After a bit more looking it may be the same problem as described on post http://discussions.apple.com/thread.jspa?threadID=1954449&start=0&tstart=0 as we've been away for a week. Also the battery is the same model number (although not firmware) as the one listed in the info for Battery Updater 1.4.
First things first, I need to backup then upgrade the MacBook to 10.5.8 as the Battery Updater 1.4 requires 10.5.6 or later. Then try the Battery Updater and a charge to see what happens and if all else fails maybe a visit to Apple (eveb though AppleCare is long gone) as the battery is below 300 cycles which some people have got Apple to replace as a faulty battery.

Similar Messages

  • Late 2007 MacBook White Will Not Update After Installation of 10.6 Snow Leopard

    I'm wondering if anyone can help me with this problem and hopefully diagnosis it as a non-motherboard or logic board issue.
    Had 10.7.8 installed successfully for 4-6 months, upgraded from 10.6.8, the end of Snow Leopard.
    Had to force shut down computer after external hd wouldn't eject.  After restarting, computer never restarted (was stuck on Apple/spinning wheel).
    I have tried everything, PRAM reset, SMC reset, hard reset (battery out, power button 5-10 seconds), recovery mode reinstall of Lion, reinstall of Snow Leopard pre-hd format, zero hd format + reinstall of snow leopard, reinstall of original install disk 10.5 to failed software update.
    I've literally tried everything.  I'm able to reinstall base OS' but not update to recent versions either 10.5.8 or 10.6.8 to upgrade back up to 10.7.5 Lion.
    Oh, and don't tell me to do a D at start up for a hardware test, it came back with nothing wrong, and my 500gb western digital hd (1 month old) has been verified and seems to be ok and repaired permissions which there were a lot but still seemed to be ok after.
    Anyone have any advice?  Motherboards are around 400$ from MacMall.
    It'd be great not to have to throw this thing away as it's still a solid work/office computer.
    Or should I just stick to 10.6 base Snow Leopard?
    Thanks everyone!
    Chase

    OK, now you need to update it to 10.6.8: Download and install Mac OS X 10.6.8 Update Combo v1.1.
    Sign into the App Store with the Apple ID you used to purchase Lion. Click on the Purchases icon in the toolbar. Look for your Lion purchase in the list and click on the Download/Install button.
    I suggest for the future you read this:
    Make Your Own Mountain/Lion Installer
    1. After downloading Mountain/Lion you must first save the Install Mac OS X Mountain/
        Lion application. After Mountain/Lion downloads DO NOT click on the Install button.
        Go to your Applications folder and make a copy of the Mountain/Lion installer. Move
        the copy into your Downloads folder. Now you can click on the Install button. You
        must do this because the installer deletes itself automatically when it finishes
        installing.
    2. Get a USB flash drive that is at least 8 GBs. Prep this flash drive as follows:
      a. Open Disk Utility in your Utilities folder.
      b. After DU loads select your flash drive (this is the entry with the mfgr.'s ID and size) from the left
          side list. Click on the Partition tab in the DU main window.
      c. Under the Volume Scheme heading set the number of partitions from the drop down menu to one.     
          Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the
          partition scheme to GUID then click on the OK button. Click on the Partition button and wait until
          the process has completed.
      d. Select the volume you just created (this is the sub-entry under the drive entry) from the left side
          list. Click on the Erase tab in the DU main window.
      e. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the
          button for Zero Data and click on OK to return to the Erase window.
      f. Click on the Erase button. The format process can take up to an hour depending upon the flash
         drive size.
    3. Locate the saved Mountain/Lion installer in your Downloads folder. CTRL- or RIGHT-click on the installer and select Show Package Contents from the contextual menu. Double-click on the Contents folder to open it. Double-click on the SharedSupport folder. In this folder you will see a disc image named InstallESD.dmg.
    4. Plug in your freshly prepared USB flash drive. You are going to clone the content of the InstallESD.dmg disc image to the flash drive as follows:
      a. Double-click on the InstallESD.dmg file to mount it on your Desktop.
      b. Open Disk Utility.
      c. Select the USB flash drive from the left side list.
      d. Click on the Restore tab in the DU main window.
      e. Select the USB flash drive volume from the left side list and drag it to the Destination entry field.
      f. Drag the mounted disc icon from the Desktop into the Source entry field.
      g. Double-check you got it right, then click on the Restore button.
    When the clone is completed you have a fully bootable installer that you can use without having to re-download Mountain/Lion.
    Note: The term Mountain/Lion used above means Lion or Mountain Lion.
    As an alternative to the above (you still have to do your own download of Lion/Mountain Lion) you can try using Lion DiskMaker 2.0 that automates the process of Steps 2 through 4.

  • Bumpy battery - Late 2007 Macbook

    Hi,
    I would like to ask if anyone has noticed a weird behaviour of their batteries with the late 2007 Macbook.
    My battery still works but it has begun "shapeshifting".
    It started being a little bumpy in the middle but now the bump is being more and more noticeable: you can even have the perception it is going to jump out from the MacBook.
    On the internal side, as proof of the shapeshift, some "points" have appeared exactly in the area which is at contact with the metal-like plate as a result of
    I'm getting worried, I would not like my MacBook battery to explode while I'm on a plane or something.
    I began using it without battery but I cannot use it only as a "small desktop replacement".
    So.. anyone with the same issue?
    My best regards,
    Maurizio

    I think that the "MacBook with no battery" is faster than the "MacBook with exploding battery" option, so I'll stick with it as long as I can
    I have to agree on that
    Make sure your battery desn't leak being bumpy and all.

  • Is it possible to install a 4 GB of RAM memory to a late 2009 macbook white?, Is it possible to install a 4 GB of RAM memory to a late 2009 macbook white?, Is it possible to install a 4 GB of RAM memory to a late 2009 macbook white?

    Is it possible to install a 4 GB of RAM memory to a late 2009 macbook white?

    Maximum Memory     8.0 GB (Actual) 4.0 GB (Apple)
    Memory Slots     2 - 204-pin PC3-8500 (1066MHz) DDR3 SO-DIMM

  • Late 2007 MacBook Pro intermittent black screen

    I have this very odd issue with an intermittent black screen on a late 2007 MacBook Pro (4GB/320GB 7200rpm) Mac OS X 10.6.8 v1.1
    Apologies for the length of the post.
    In cycles separated by a few days to a week, the screen will flicker to black, initially very briefly, then for longer periods until it is black continuously, where it stays from a few hours to a couple of days then it flickers to normal, again very briefly then with longer intervals until it is steady and normal. It can then be fine for a week or more.
    When the screen is working, it's perfect; no lines, stripes, colour shift or any difference to what one would expect. When it is black, the backlight is still operational (and dimming when on battery power) but there is no image - all pixels are solid black. Shining a torch on/through the screen does not reveal any image. When mirrored, the external monitor shows the brightness adjustment moving up and down in response to the key presses but it has no effect on the internal screen.
    My external display (Eizo) is always functional no matter what the built-in one is doing and is completely solid at all times.
    There is no correlation to temperature (I have SMC fan control), sleep, restart, fan speed, power source or anything environmental. The MacBook is on a fan stand for most of the time. External connections make no difference. If the fault is present before changing any of these factors, it is there after.
    I am aware that this machine has known vulnerabilities with GPU and display issues but none present quite like this. I have performed the usual trawl on the net and I now know more than I ever wanted to about attempts to fix it.
    Software remedies attempted:
    Resetting PRAM and power manager.
    No sleep image file (never used this option). I deleted the old swap files that were there in any case but this unsurprisingly did nothing.
    Resetting the display settings via keyboard commands or Sys Prefs.
    Screen savers and settings are not implicated.
    Nothing whatever in the console logs that I can see.
    TechTool Pro gives video RAM a clean bill of health and all other components pass including tests on the HD with TTP and DiskWarrior.
    Safe boot and booting from systems on backups seem to have no effect but one safe boot restored the screen briefly - I think it was a coincidence.
    I updated the OS from 10.6.6 to 10.6.8 while this fault was coming and going and it made no difference. I usually prepare the machine for updates by running the cron jobs, repairing permissions etc.
    In expectation of suffering this fault when the external monitor was not connected, I installed iScreen on the MacBook and use my iPad as a supplementary display and that works well too. Having all three operating, when the internal is functioning, is quite fun.
    Hardware tests:
    I removed the upper plate holding the keyboard and the interior of the machine was very clean with only some small dust accumulations in the fans, which were removed. There was no sign of any discolouration, corrosion, or other unpleasantness on the PCBs. All connectors and wiring looked good.
    Every part of the logic board, cables and connectors were percussed, gently deflected and spray freezed, both while the fault was present and not (machine running) with no effect.
    Display back was removed and the LCD board given the same treatment. No changes.
    Display cable disconnected at both ends and tested for continuity (probe resistance accounted for) and consistency with a Fluke 87 multimeter - passed OK. On a scope, active signals and power were present on all the pins when the display was working but the fault did not occur during this test, which might have been interesting.
    No apparent shorting of the display cable but without removing it this cannot be proved.
    Problem not affected by hinge position, pressure on any part of the display, twisting, percussing etc.
    Used compressed air to blow out the connectors which were reseated carefully.
    After all this, the machine remains in exactly the same state, cycling between operational and black with various flickering stages as it comes and goes.
    All I can deduce is that as the external monitor has always been OK, the GPU itself is probably working fine and the fault is more likely in the LCD panel electronics. I doesn't feel like a software issue to me but heck, I don't know what is going on.
    Does anyone have any experience of something like this?
    Thanks,
    Joel.

    Thomas,
    Thanks for your post and I'm sorry you have suffered the same problems.
    My trust levels are not very high because it's clear there is some systemic display problem with this model, which is why Apple are fixing them. As I mentioned, we have no idea if the replacement boards are any different to the originals. From your experience it would look like they are not and my suspicion is that it is very unlikely that Apple made a new batch of these logic boards a long time after the model was discontinued. If anyone has evidence to the contrary, I stand to be corrected.
    As you say, the difference between our two faults appears to be that a physical deformation of some part of the machine does something with yours but never did with mine. At one point I felt that a short in the internal display cable seemed like the best explanation for the problem but it looks like it's more complex than that because of the behaviour of our external displays and subsequent strange booting behaviour.
    If, as I have read, the soldering of the GPU was faulty and leads to progressive failure of the graphics sub-system, then all kinds of strange behaviours could arise and produce the intermittent problems we have seen. Micro-fractures of the chip interconnects would suggest that tiny movements might change the presentation of the fault. If soldering really is the issue, then keeping the machine as cool as possible will extend the life of the connections. Consequently mine will sit on a fan-stand for the rest of its days, which is no problem because it just had Win 7 installed on it and I don't want to be seen in public with it in that state ;-)
    All we can conclude is that a logic board swap fixes the problem for some indeterminate period, so the problem is on that board. Whether it is a design fault with the NVIDIA chip itself or a manufacturing fault with the board is not clear but we can probably forget LCD panels, cables, sleep issues, power supplies and all the other peripheral issues unless there is yet another design issue that causes the GPU to fail.
    Are you intending to present your machine to Apple for another go at a fix?

  • Scrollbars always on after upgrading Late-2007 MacBook

    After upgrading my wife's white Late-2007 MacBook, I noticed the scrollbars are always on and not like my MacBook Pro where they fade in and out. I don't think it is because her trackpad is not multi-touch.
    Does anyone know why this happens?
    Thanks in advance!

    If you have Mountain Lion, use "System Preferences > General > Show scroll bars > When scrolling".  I don't have any machines left with Lion to see if the preferences are different.
    "automatically based on input device" means the scroll bars dissappear if a trackpad which supports scrolling gestures is present (and no mouse is present).  Non-multitouch trackpad is probably treated as a mouse in this case.
    Hope this helps...

  • LATE 2007 MACBOOK STILL CRACKING

    I have a late 2007 13 inch macbook that I bought about two months ago. About a month after I got it, the bottom case started splintering around the ports, followed shortly by a hairline crack perpendicular to the escape key. I took it to a Mac store and they told me it was accidental damage. I called Mac and talked to a specialist and the specialist told me they would fix it if i sent it in.
    Everything was fixed for free by mac. I have now had it for about another month and another crack has developed around the battery on the bottom case. Is anyone else having this problem with their Late 2007 Macbook? I thought these problems were resolved. I am also having palm rest discoloration...this isn't supposed to still happen either...is it?
    Please comment.

    I have had this issue twice with my Macbook which I bought in August 2007, the first time was less then 2 weeks after I had my machine so they replaced it with a brand new machine, the second time was just recently and they claimed that the damage wasn't covered by my Applecare. However the second time the cracks occurred I had brought my Macbook in to fix a crack in the palmrest (the second time I have had to fix this, thankfully that damage is covered as it is a well known issue with the Macbooks), the hairline cracks on my macbook weren't there before I sent my notebook in but when I recieved it there were hairline cracks near the ports, on one of the back hinges, and on the front edge... plus there were gaps where the keyboard/trackpad piece meets the bottom part of my Macbook. So it was obvious that the repairs were done shoddy, and I politely but firmly demanded that they fix the damage which was caused by them... so thankfully they sent it in to fix the casing, hinge, and to remount the keyboard/trackpad piece properly. I am hoping this will be the end of my cracking issues but within a year I have had to bring my laptop in 4 times due to cracking case issues... and I treat my notebook very gently. Thankfully I haven't had any issues with discoloration, but I wish Apple would fix the cracking issues on these lovely machines.

  • Late-2007 Macbook constantly crashing

    I have a Late-2007 Macbook (the plastic one) which runs 10.7.5. For the past month and a half, I will be on my computer and suddenly everything stops working. Webpages stop loading, I can't switch or quit out of programs, etc. Then suddenly, my computer crashes. When it crashes, the whole computer goes black but you can hear that it's still on. To turn the computer back on, I have to hold down the power button to shut the computer off completely. When I turn it back on, everything works as normal. This has been happening about once every two or three days, except once or twice it has gone a week without crashing. I verified and repaired the computer's harddrive using the disk utility application, however that did not help. Also, it's happened when I had open a number of different programs so it doesn't appear that it could be an application causing it to crash (for example, it's crashed while I've used Google Chrome and another time when I've used Firefox so that doesn't seem to be the issue) Has anyone had this problem and/or know a possible solution?
    Thank you in advance!

    I have a Late-2007 Macbook (the plastic one) which runs 10.7.5. For the past month and a half, I will be on my computer and suddenly everything stops working. Webpages stop loading, I can't switch or quit out of programs, etc. Then suddenly, my computer crashes. When it crashes, the whole computer goes black but you can hear that it's still on. To turn the computer back on, I have to hold down the power button to shut the computer off completely. When I turn it back on, everything works as normal. This has been happening about once every two or three days, except once or twice it has gone a week without crashing. I verified and repaired the computer's harddrive using the disk utility application, however that did not help. Also, it's happened when I had open a number of different programs so it doesn't appear that it could be an application causing it to crash (for example, it's crashed while I've used Google Chrome and another time when I've used Firefox so that doesn't seem to be the issue) Has anyone had this problem and/or know a possible solution?
    Thank you in advance!

  • Late 2007 Macbook Pro: DVI to VGA Adapter

    I lost my DVI to VGA Display Adapter for my late 2007 Macbook Pro and can only find adapters for the PowerBook G4. Will this adapter work for my Macbook Pro?
    Thanks!

    Yes, all of those DVI+A to SVGA/VGA adapters for Macs are the same. I have adapters from the titanium G4, aluminum G4 and intel MBP and they all have DVI and came with adapters that function the same.

  • Late 2007 MacBook Pro S-Video adapter no output.

    I've troubleshooted everything I can, so hopefully one of you can help me!
    My Fiancé's mom has a late 2007 MacBook Pro running Mountain Lion. She has an older tv, so I was wanting to mirror the display so she can watch Netflix on her TV.
    After digging around on the Internet, other users said the APPLE M9267G/A adapter solved this problem without the need for a converter box, or upscaler. Needless to say, it doesn't work..
    I've tested the cable, port on the computer, and they both work. I've tried running just the yellow Composite video out instead of the S video through the video in on the TV, and a VCR... Nothing.
    I used my old Powerbook 1.67, which has an S Video out to the TV, and it works perfect. When I plug the adapter into the Powerbook's Dual Link DVI port, same port as the MacBook Pro, it doesn't work..
    I chose S-Video, even though the TV has Component inputs, because other forums said it wouldn't work without an expensive converter box.
    They said this would be the solution.
    Does anyone have any suggestions?
    Thanks!

    Same problem, though with an early-2008 MBP. Things worked fine with 10.6.x and as soon as I went to 10.9 the external display stopped working.
    The first time I plug in the adaptor (whether or not there is a video cable attached) the screen goes black and nothing shows up on the external screen. When I unplug the adaptor, I get the display back on the MBP but it's at low resolution and it has put me at the general login screen. When I put the adaptor back in the second time, it essentially locks up the display to where it is black and no key presses or adaptor removals brings the display back. I have to reset the MBP by holding down the power button. I submitted a bug report too, but have no faith Apple will do anything. Big fail, Apple.

  • What can i upgrade to and how? late 2007 macbook pro

    I am running tiger 10.4.11 can i go straight to mountain lion or do i need to install all 4 in between leopard snow leopard lion and then mountain lion i have a 13" late 2007 macbook pro thank you

    Yes. Snow Leopard requires at least 1GB of RAM; the Mac App Store will check compatibility before allowing Mountain Lion to be purchased.
    (88252)

  • Late 2007 Macbook pro 15inch Mavericks update?

    I have a late 2007 Macbook pro 15inch which I love. Can it be updated to mavericks or must I bid it a fond farewell?
    Thank you!

    Your Mac originally came with 2 GB of RAM.  Mavericks will run in that amount but will be slower than if you have 4 GB or 6 GB.  If after you upgrade you want more speed see OWC (macsales.com) or Crucial.com for memory upgrades.  They are inexpensive.

  • Late 2007 MacBook Pro - Fresh install

    I have a late 2007 MacBook Pro. I want to do a fresh install. Is it best to use the original discs, which would take me back to tiger, or can I just use a new retail copy of Snow Leopard?
    Will that retail copy of Snow Leopard hold all the proper drivers for the late 2007 mbp?

    I just did a fresh install of Snow Leopard on my late 2007 MPB (I bought it in Jan 08 and it shipped with Leopard). Worked out fine, only difference is the Retail Snow Leopard doesn't bundle the iLife applications like the originals did. Other than that it went very smoothly.

  • HT1338 Serial # W87*****Z67 OS 10.7.4 is my late 2007 MacBook Pro (black) but when attempting to purchase X Lion upgrade I get message that hardware is not supported. But X Lion tech spec says mid to late 2007 Macbook pros supported. Any thoughts?

    Serial # W87*****Z67 OS 10.7.4 is my late 2007 MacBook Pro (black) but when attempting to purchase X Mountain Lion upgrade I get message that hardware is not supported. But X Mountain Lion tech spec says mid to late 2007 Macbook pros supported. Any thoughts?
    <Edited by Host>

    See  babowa Post Here... on Compatibility...
    https://discussions.apple.com/thread/4136749?tstart=0

  • Streaming content to Apple TV from Late 2007 MacBook Pro without AirPlay

    What is the method of streaming content to a third-generation Apple TV from a late 2007 MacBook Pro?  This Mac doesn't support AirPlay.
    If this feature is not supported by Apple, what are some third-party options?

    Use AirParrot > http://www.airparrot.com

Maybe you are looking for