Prime 2.2 Power supply alarms

doing some testing in a new data centre with Prime 2.2 and wondering if there is a way to be immediately notified in the event I lose a power supply or a fan.
I thought I had all the monitoring turned on but when I pulled a power supply I had to re-sync the device before Prime knew about it and then it still never notfied me.

hey
i have issue aswell to get snmp poll working optimal so atm in pi i am working more on snmp trap and syslog as the way to get the notification.
snmp-server trap-source [interface]
snmp-server host [pi-ip] (vrf [vrf name]) version 2c [community string]
snmp-server enable traps envmon supply
secend minor issue is pi only set this a minor error so if you treshold on email notification is set to critical you wil never get and email alarm so if that is a must you must edit the servirity og the alarm og send warning email as well

Similar Messages

Prime Infrastructure 2.1 - Power supply alarms on switchs

Hi,
How can i manage to get a email if one of my power supply on a switch die (see the attached file).
I tried to activate all snmp traps possible on my switch and all i can get is configuration management events on PI.
I changed the Severity Configuration on PI for Environmental monitor detects a testpoint reaching a critical state to critical.
Any ideas?
Sorry for grammar, english is not my native language.
*** Prime Infrastructure 2.1, we will upgrade for 2.2 in few weeks***

Hello,
It's tracked by the following bug:
CSCui46231 Processing Alarm on power supply failure and Fan failure conditions
Should be resolved in PI 2.2
Ram

I keep getting an alarm on my xserve telling me power supply has failed

Raid admin shows an event that power supply 2 has failed and the audible alarm goes off on the server but the the components section in raid admin shows all ok.
also the power supplys both seem to be running ok when I look at them visually.
is this a bug or should I replace the power supply?
RT

Can you clarify what Mac and Mac OS you really have? Facetime was introduced in 2010, four years after PowerMacs were discontinued. And "iOS" is not an computer OS.
Doing "About this Mac" will show your processor type and OSX version. That should help us figure out if you need to be moved to a different forum.

Choosing the Right Power Supply

First things first. If you've got a poor-quality and/or faulty power supply, nothing else you do will work to solve your problems. Stick to the basics before you go further...The short answer is to buy a hi-powered, brand name supply, like the new ENERMAX line (430 W or higher) or ANTEC True550. Almost nothing else will do with today's computers. In over 30 years of electronic/computer service, I have found that 85% or more of problems were power-related.
If you want to know more, read on...
Choosing The Right Power Supply
If you’re reading this, there’s a good chance that one of my colleagues or I believe that you could be experiencing problems with your power supply, based upon the symptoms you mentioned in your post, and provided you with this link. Relax, you’re not alone. In 30 years of electronic and computer troubleshooting, I’d say that the majority of the electronic, mainframe, mini, and microcomputer problems I’ve diagnosed and repaired were with the basic power the problematic device was receiving. The symptoms often included random reboots, crashing, the BSOD, lockups, etc.
(As the national support technician for few major computer service companies, working US Defense contracts, I was often the person that had to fly in and correct the problem, or “walk through” the on-site technician as he closely followed my instructions. I achieved success in my career by carefully reading the manuals, knowing where to go for more information that was otherwise unavailable to me, and/or systematically troubleshooting until the problems were discovered and repaired. I never had the option of giving up.)
The most overlooked component when building or upgrading a PC is the power supply unit (PSU). Some people use their old case and PSU when they upgrade. Some use the PSU that came with their new case. Some people even buy a new PSU. And most inexperienced builders all make the same mistake: The PSU that they’re trying to use is simply inadequate for the job.
Suppose you’re upgrading to a new motherboard, CPU, ram, and video card, but still using the old case and PSU. It’s most likely that you’re upgrading in order to build a machine that is more powerful, faster, has a more colorful display, can number-crunch more quickly, play the latest games, etc. These gains in performance all have one thing in common: They require more raw power. However, have you thought about where that power comes from?
Suppose you’re building a new system with a new case and PSU. Has it occurred to you that the company that you bought the case/PSU from might make more money if they skimp on the supply, even if the supply has a large wattage rating? Most bulk power supply manufacturers don’t make good PSU’s. They use older, cheaper technology, and slap on labels that represent the PSU’s peak outputs, and not their continuous output rating. These companies are intentionally misleading you in order to sell you an inferior product. Brands I avoid when building/repairing my friends’ and family’s computers: Allied, Q-Tec, Chieftech, and many others.
For those of you who bought a power supply separately, did you know that you’re only supposed to run a power supply continuously at 30-70% (with 50% being optimal) of its continuous rating for maximum efficiency (which means less heat to you)? Most inexperienced builders either buy PSU’s that are matched to their equipment’s continuous power usage, or ones that are even less powerful than they need. Why? Because they’re trying to save money.
I mean, what’s the fun in a power supply? You don’t get any games with it, there’s no more storage, hardly ever any more bells and whistles, etc. A power supply is boring, and it’s supposed to be, because it’s supposed to provide a stable, reliable platform upon which the rest of the equipment can easily access the amount of power it needs, and when it’s needed. In almost EVERY review of powers supplies, the same point is stressed: Better safe than sorry.
But what does safe vs sorry mean? It can mean that you don’t have to waste money on the wrong PSU in the first place, but it can also mean that you don’t have to replace your expensive ram, CPU, video card, etc. NEEDLESSLY, or because your cheap PSU destroyed them. What? A cheap power supply can wreck your computer? YES IT CAN. A cheap power supply can cause thermal damage, not only from the heat it produces, but also the heat it can create in your components as well. RAM is especially sensitive to heat, and there’s RAM in your CPU, your video cards, and, well, your RAM too. A cheap switching power supply, run at its maximum, or peak, continuously can also destroy components by creating RF (Radio Frequency) signals on your power rails, signals which the components on your peripheral devices were not equipped to handle in the first place.
So this begs the question, how does one choose the right power supply? I’ll illustrate this using my own PC as the example. This is my setup that I use for video processing:
K7N2G-ILSR
Athlon 2500+ Barton @ 2125Mhz
AMD Retail Heatsink/Fan
2 - 512MB DDR333 w/Thermaltake Spreaders (slot 1&3)
MSI TV@nywhere Video Capture
ATI Radeon 9600
120GB Maxtor DiamondMax Plus 9 SATA
30GB Quantum IDE
TEAC DV-W50E DVD/CD-R/W
BTC DVD-ROM Drive
Artec CD-R/W
Using this Power Supply Calculator link:
http://www.jscustompcs.com/power_supply/
I plug in all my equipment values, but some of this can be a little tricky. For example, since I often run the CPU like an XP 3000, I choose the 3000 as my processor; it’s the same chip run at the faster rate. I also choose the ATI Radeon video card, and I select the RAM wattage for 2 sticks of DDR. I also choose every card I have, like my video capture card, but I also select the boxes for the separate cards that correspond to the functions that my ILSR provides as well (and that I use), like sound, USB, Firewire, NIC, etc. Although I use the onboard SATA controller, I don’t select the SCSI PCI card, because, in truth, I’ve probably made up for it by selecting all the other corresponding devices, including cards that the motherboard replaces. I check the boxes for the fans and drives I use, and I’m done, right?
Not yet.
I just remembered that I plan to upgrade soon, so I go back and change the values to reflect my impending changes. I mean, I want to make sure that I have enough power to begin with so that I don’t have to replace the power supply again, right?
Ok. Done. I look at the bottom and see that it tells me that I need a 468 watt PSU. So a 480 watt supply will do, right? Wrong.
Remember that, for efficiency, long-life, and less heat, you want your actual power consumption to fall between 30-70% of the PSU’s rating, so add 30% (minimum) to the 468, and you get 468 + (468*.30)= 608 Watts! Holy Cow!
However, I’d only need a 608-Watt supply if I was using all the devices at once, and I don’t. But, in truth, with video and audio processing, I often get close when I process, burn, and monitor at the same time. (Hardcore gamers also get close a lot, as they blast the sound and push that video to its limits.) So, let’s take off 10% (maximum) of 608, for a total of 541 Watts.
I need a 550 Watt supply, but not just ANY 550 watt PSU. I need a supply that can give me enough power on the critical 3.3, 5, and 12V rails combined. I also want a supply from a trusted, name-brand manufacturer, so I start hitting the many online reviews. Here are just two from Tom’s Hardware:
http://www6.tomshardware.com/howto/20030609/index.html
http://www6.tomshardware.com/howto/20021021/index.html
Read these in their entirety. I didn’t post them because they’re pretty links.
In the end, I chose Antec, because they’ve got the reputation, the recommendation, and because the Antec True550 has better specs than the rest of the 550 Watt competition. I also bought it from a reputable company I found on Pricegrabber.com, for the lowest price I could find, $95.00 shipped to my door. (In truth, I wanted two mini-redundant supplies, like the hospitals and military use, but they were too expensive.)
The result? Not only are the random reboots, crashing, the BSOD, lockups, etc., gone like magic, but I also now have “peace of mind” in that whatever might happen to my equipment in the future, I know almost for certain that the PSU is NOT the problem. I also bought an UPS, because the East Coast Blackout proved to me that even the Antec True550 isn’t going to provide me any power for emergency shutdown if it doesn’t get its power from somewhere.
Even if your problem doesn’t lie in the PSU completely, it gives you a GREAT platform for troubleshooting further. If you’re not reasonably certain that the supply is the cause, borrow one, or buy one that you can return once you’ve solved the problem. But, above all else, BUY THE RIGHT SUPPLY before you do anything else! Otherwise, you could be plugging and unplugging components, buying and blowing up expensive memory, and causing even further damage, until you give up or die.
I mean, I assume you built your own system to enjoy “more bang for your buck,” right? What’s the fun of a random reboot in the middle of Unreal Tournament 2003?
William Hopkins
Former Staff Sergeant, USAF
B.A., B.S., with Honors
The University of California, San Diego
[email protected]
P.S. It should be noted that while Enermax, ThermalTake, Zalman, Fortron, and others make great PSU’s, and I compared and considered them, the Antec still won out overall in my critical evaluation, like it did in so may others’ reviews. You’d probably be ok if you went with another reputable manufacturer as listed above, but pick a supply that gives you at least 230 watts on the 3.3 and 5V lines combined, and still meets the 30% criteria as stated above. Remember, if the manufacturers don’t give you maximum combined specs up front, they’re untrustworthy right off the bat. With power supplies, you definitely end up getting what you pay for. Don’t say nobody warned you.
P.P.S. Update! After recent developments, it looks like Enermax is the leader, but only the latest line of PSU's.

Ok, as an electrical engineer...I have to step in here! LOL
First, these amp rating are for 2 +12 rails. That is why you see a protection of around 15-18A on the +12 rail. That means each Rail is allowed up to 18A lets say for the new Enermax 1.2 version like the one I have.
Now, Lets say 18A for 12V....well as you know the Abit NF7-S uses the 12V for powering the CPU.
Lets say you have a Barton like me and you want it stable at around 2.4-2.5Ghz. You will have to put lets say around 2V to the cpu to get it stable at that kinda speed, specially if you have high FSB like I do. So 12V * 18Amps = 216W ....well the converter on the NFS-7 is really bad, its loss on the step down convertion is probably around 25% along with the PSU lost cuz its not running at 25oC (another 15%)....you will actually only get around 100-120W for the CPU.
Now, if you go into Sandra and see how much a Barton eats up at 2.4Ghz you will see its around 110Watts.
So, if you wanna push more, dont even think about it! Prime Power test fails and your +12 rail will drop as low as 11.60 Volts.
Now, lets say you got yourself a AMD 64 bit chip and you wanna overclock it....I bet it will need more than 110Watts.
So, what im saying is, dont buy nothing less than a 500 Watt PSU!
You really need around 20-22 A on the main +12 along with really really good cooling on the case and PSU so it is running at a 100%.
http://forums.amdmb.com/showindex.php?s=&threadid=287828
i found this quite interesting especially the bit re the power loss turning the 12v into 1.6v or what ever cpu needs

Power supply voltage upper-non-recoverable

Hello,
One of our customers is seeing the following errors occur intermittently across all 4 power supplies in their chassis. They are running 2.0(2q). The chassis is powered via an APC UPS and PDUs, and there are no power events or alarms from within the APC InfraStruxure tools. Has anyone else seen these errors in 2.0(2q) or is this error indicating a voltage fluctuation from the UPS?
Sent: Monday, April 30, 2012 6:26 AM
To: ITNotify
Subject: System Notification from PFS-UCS-A - environment:major - 2012-04-30 12:26:39 GMT-00:00 Recovered : Power supply 4 in chassis 1 voltage: upper-non-recoverable
<?xml version="1.0" encoding="UTF-8" ?>
<soap-env:Envelope xmlns:soap-env="http://www.w3.org/2003/05/soap-envelope">
<soap-env:Header>
<aml-session:Session xmlns:aml-session="http://www.cisco.com/2004/01/aml-session" soap-env:mustUnderstand="true" soap-env:role="http://www.w3.org/2003/05/soap-envelope/role/next">
<aml-session:To>http://tools.cisco.com/neddce/services/DDCEService</aml-session:To>
<aml-session:Path>
<aml-session:Via>http://www.cisco.com/appliance/uri</aml-session:Via>
</aml-session:Path>
<aml-session:From>http://www.cisco.com/appliance/uri</aml-session:From>
<aml-session:MessageId>1232:SSI15420KDL:4F9E84FF</aml-session:MessageId>
</aml-session:Session>
</soap-env:Header>
<soap-env:Body>
<aml-block:Block xmlns:aml-block="http://www.cisco.com/2004/01/aml-block">
<aml-block:Header>
<aml-block:Type>http://www.cisco.com/2005/05/callhome/environment</aml-block:Type>
<aml-block:CreationDate>2012-04-30 12:26:39 GMT-00:00</aml-block:CreationDate>
<aml-block:Builder>
<aml-block:Name>UCS 6248 Series Fabric Interconnect</aml-block:Name> <aml-block:Version>5.0(3)N2(2.02q)</aml-block:Version>
</aml-block:Builder>
<aml-block:BlockGroup>
<aml-block:GroupId>1233:SSI15420KDL:4F9E84FF</aml-block:GroupId>
<aml-block:Number>0</aml-block:Number>
<aml-block:IsLast>true</aml-block:IsLast>
<aml-block:IsPrimary>true</aml-block:IsPrimary>
<aml-block:WaitForPrimary>false</aml-block:WaitForPrimary>
</aml-block:BlockGroup>
<aml-block:Severity>6</aml-block:Severity>
</aml-block:Header>
<aml-block:Content>
<ch:CallHome xmlns:ch="http://www.cisco.com/2005/05/callhome" version="1.0">
<ch:EventTime>2012-04-30 12:26:39 GMT-00:00</ch:EventTime> <ch:MessageDescription>Recovered : Power supply 4 in chassis 1 voltage: upper-non-recoverable</ch:MessageDescription>
<ch:Event>
<ch:Type>environment</ch:Type>
<ch:SubType>major</ch:SubType>
<ch:Brand>Cisco</ch:Brand>
<ch:Series>UCS 6248 Series Fabric Interconnect</ch:Series> </ch:Event> <ch:CustomerData> <ch:UserData> <ch:Email>[email protected]</ch:Email>
</ch:UserData>
<ch:ContractData>
<ch:SiteId>2089409</ch:SiteId>
<ch:ContractId>90874841</ch:ContractId>
<ch:DeviceId>UCS-FI-6248UP@C@SSI15420KDL</ch:DeviceId>
</ch:ContractData>
<ch:SystemInfo>
<ch:Name>PFS-UCS-A</ch:Name>
<ch:Contact>IT Department</ch:Contact>
<ch:ContactEmail>[email protected]</ch:ContactEmail>
<ch:ContactPhoneNumber>+18018442180</ch:ContactPhoneNumber>
<ch:StreetAddress>1420 South 500 West, SLC UT 84115</ch:StreetAddress> </ch:SystemInfo> </ch:CustomerData> <ch:Device> <rme:Chassis xmlns:rme="http://www.cisco.com/rme/4.0">
<rme:Model>UCS-FI-6248UP</rme:Model>
<rme:HardwareVersion>0.0</rme:HardwareVersion>
<rme:SerialNumber>SSI15420KDL</rme:SerialNumber>
</rme:Chassis>
</ch:Device>
</ch:CallHome>
</aml-block:Content>
<aml-block:Attachments>
<aml-block:Attachment type="inline">
<aml-block:Name>sam_content_file</aml-block:Name>
<aml-block:Data encoding="plain">
<![CDATA[
<faultInst
ack="no"
cause="voltage-problem"
changeSet=""
code="F0391"
created="2012-04-30T06:25:39.162"
descr="Power supply 4 in chassis 1 voltage: upper-non-recoverable"
dn="sys/chassis-1/psu-4/fault-F0391"
highestSeverity="critical"
id="218782"
lastTransition="2012-04-30T06:26:39.630"
lc=""
occur="1"
origSeverity="critical"
prevSeverity="critical"
rule="equipment-psu-voltage-threshold-non-recoverable"
severity="cleared"
status="modified"
tags="network,server"
type="environmental"/>]]>
</aml-block:Data>
</aml-block:Attachment>
</aml-block:Attachments>
</aml-block:Block>
</soap-env:Body>
</soap-env:Envelope>

Brad,
It looks like the system is running into following defects which is still under investigation.
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtx90410
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtz59519
Please open a TAC service request so that we can help you out.
HTH
Padma

Power supply or logic board failure

First time post, long time Mac user (since 1983). My older iMac G5 1.8 GHz Power PC (ALS) occasionally fails to start when I press the power button or the internal power button on the logic board. The only solution is to unplug/plug the external power cable where it meets the power supply housing (not at the outlet). None of the capacitors seem to be bulging on the logic board, LED1 always lights up, LED2-4 fail when there is a problem but are normal after unplug/plug routine. Noticed that there was no internal Lithium battery where one is supposed to be, but this has been the case for 5 years, so this is probably not the issue. I suspect the power supply. It's an old iMac with plenty of leg left and will be used as a second computer in the home. Any ideas? I don't have a volt meter, but am willing to get one if the test points are easy to get to (I'm not an electronics wizard).

Welcome To Discussions - If resetting the SMU, which is in effect what you are doing, solves the problem and the caps look ok, then the prime suspect would be the power supply unit. They are not expensive, check out [synaptech.com] for prices or[welovemacs.com] whcih will also give you instructions on how to replace it.
It would probably be a good idea to replace the battery it's CR2032 3 volt lithium button, easily obtainable at Radio Shack or similar places.
Let us know how you make out,

Storage Tek 6140 - Power supply event

Goodmorning,
I found an event during my routine checks relating to a tray power supply.
The event is:
Severity:              Major
Date:              14-Jan-2010 4.02.14
Actionable:      No
+Description:      Jan 14 04:02:14 GALAXY Tray.3 (Power Supply): [ID 0x280D] NOTICE: Drive tray component failed or removed      +
Data:              Drive tray component failed or removed
Component:      Tray.3 (Power Supply)
Type:              Log
Info:
Event Code:      57.20.461
Aggregated      Yes
As a probable cause I have this info:
This event was triggered by a logfile entry that a component has
failed.
A corresponding StateChangeEvent should have also been triggered.
And as a recommended action I have:
+1. Follow the Recommended Action in the corresponding+
StateChangeEvent.
+2. If no StateChangeEvent is present. Follow the appropriate Service+
Procedure for replacing the indicated component.
After this log, another info is mentioned in CAM events:
Monitor device event:
Severity:              Minor
Date:              14-Jan-2010 9.26.45
Actionable:      No
Description:      Finished monitoring run for device. Completed with 0 event(s).
Data:              Monitoring device GALAXY
Gathering log messages for GALAXY
No events created for GALAXY
Creating health messages for GALAXY
Saving GALAXY data...
Finished saving GALAXY data.
+     +
Component:      GALAXY
Type:              MonitorDeviceEvent
Info:
Event Code:      57.69.16
Aggregated      No
Galaxy is the name of my storage tek. I checked the health status of the tray and it is OK. Also led status is green.
I would say if the first event can be alarming also after the second event.
Thanks

Hi.
1. Disk should be work normal. In case failure - should be replaced by hotspare automaticaly.
2. You can't clear this alarm. You cant' install base FW on this disk. ( CAM can't do downgrade FW).
For clear alarm you can install latest CAM + patches and Install Baseline FW on Array ( Arrays).
I don't remember from CAM 6.6 or 6.7 CAM don't set alarm in case disk firmware mismatch.
3. CAM don't have own password database. It use system password database. Change password for user on system where CAM is installed.
( In case Solaris - passwd <username>
Regards.

Power Supply in LMS 4

I'm new on this version and I don't know how to create a Monitor/Alarm to detect that a power supply has gone down. I want to send a message.
What do you suggest?
Thanks in advance.

The Fault Monitor component of LMS 4.0 will automatically poll and detect a failed power supply. That appllies to both internal and external (RPS) power supplies.

Error NEXUS 5000 power supply - %NOHMS-2-NOHMS_ENV_ERROR

hi all,
i get, after i allready changed the power supply, the same error message again.
2010 Mar 24 20:03:53.271 L4DE8NSY523 %NOHMS-2-NOHMS_ENV_ERROR: Module 1 temperature sensor PS-1 failed.
2010 Mar 24 20:04:23.333 L4DE8NSY523 %NOHMS-2-NOHMS_ENV_ERROR: Recovered: Module 1 temperature sensor PS-1 failed.
2010 Mar 24 21:38:27.285 L4DE8NSY523 %NOHMS-2-NOHMS_DIAG_ERR_PS_FAIL: System minor alarm on power supply 1: failed
2010 Mar 24 21:38:57.299 L4DE8NSY523 %NOHMS-2-NOHMS_DIAG_ERR_PS_RECOVERED: Recovered: System minor alarm on power sup
ply 1: failed
i do not find the error explanation in the error message decoder. now i guess that not the power supply is defect but the NEXUS 5010 itself. am i right ? please advise !
Cisco Nexus Operating System (NX-OS) Software
kickstart: version 4.1(3)N1(1)
system: version 4.1(3)N1(1)
regards Reinhold.

also see http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/release/notes/Rel_4_0_1a_N1_1a/Nexus5000_Release_Notes_4_0_1a_N1_1a.html
for open caveat: CSCtb56755
it is also a cosmetic issue.

DFM - Power Supply Failed Detection on 4500s

Running DFM 3.2.0 under LMS 3.2 for Windows 2003 Server Enterprise.
DFM has been pretty good about detecting power supply failures but recently I came across one power supply failure it didn't detect. This was on a 4506 running cat4500-ipbasek9-mz.122-53.SG.bin. Could there be a bug in detection of power supply failures with this firmware version?
Also, polling for power supply failures a configurable option in DFM?
Thanks,
David

Yes, the device is known in DFM (I did a re-import just in case)
Device Status             = Known
Device Type               = Switches and Hubs
Aliases                       = N/A
Containments              = N/A
DFM Processing          = Active
Time Last Discovered = 01-Feb-2010 12:28:43
Import Time Stamp       = 01-Feb-2010 12:19:56
    *** Data Collector Status Information ***
Error Code                   = N/A
Error Message             = N/A
The power supply condition isn't reflected in the alerts.
Could it be that if the power supply is off to begin with when it does it's discovery, it doesn't register an alarm?

SNMP power supply monitoring an XR 12404

I'm trying to monitor basic health status of the Power Supply on a 12404. However, I cannot find the relevant information from the ENTITY MIB or it's Cisco extensions.

Thanks Joel. Here is the output from a walk of entPhysicalDescr:
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1 = STRING: "Cisco 12404 80Gbps fabric"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2 = STRING: "Line Card/RP slot "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.3 = STRING: "Cisco 12000 Series Performance Route Processor 2"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4 = STRING: "host__PLIM_V7_HDD_5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5 = STRING: "host__PLIM_V6_1.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.6 = STRING: "host__PLIM_V4_1.3V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.7 = STRING: "host__PLIM_V5_1.8V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.8 = STRING: "host__PLIM_V3_2.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.9 = STRING: "host__3.3V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.10 = STRING: "host__5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.11 = STRING: "host__Mbus5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.12 = STRING: "host__InletTemp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.13 = STRING: "host__HotTemp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.14 = STRING: "Line Card/RP slot "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.15 = STRING: "Cisco 12000 Series - Multi-Service Blade "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.16 = STRING: "host__12V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.17 = STRING: "host__0.75V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.18 = STRING: "host__1.2V_MPU"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.19 = STRING: "host__1.2V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.20 = STRING: "host__1.25V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.21 = STRING: "host__1.25V_IXP1"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.22 = STRING: "host__1.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.23 = STRING: "host__MB_PLL_1.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.24 = STRING: "host__1.8V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.25 = STRING: "host__2.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.26 = STRING: "host__3.3V_DB1_AUX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.27 = STRING: "host__3.3V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.28 = STRING: "host__5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.29 = STRING: "host__Mbus5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.30 = STRING: "host__HotTemp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.31 = STRING: "host__InletTemp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.32 = STRING: "Line Card/RP slot "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.33 = STRING: "Cisco 12000 Series - Multi-Service Blade "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.34 = STRING: "host__12V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.35 = STRING: "host__0.75V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.36 = STRING: "host__1.2V_MPU"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.37 = STRING: "host__1.2V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.38 = STRING: "host__1.25V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.39 = STRING: "host__1.25V_IXP1"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.40 = STRING: "host__1.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.41 = STRING: "host__MB_PLL_1.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.42 = STRING: "host__1.8V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.43 = STRING: "host__2.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.44 = STRING: "host__3.3V_DB1_AUX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.45 = STRING: "host__3.3V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.46 = STRING: "host__5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.47 = STRING: "host__Mbus5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.48 = STRING: "host__HotTemp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.49 = STRING: "host__InletTemp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.50 = STRING: "Line Card/RP slot "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.51 = STRING: "Cisco 12000 Series SPA Interface Processor- 401"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.52 = STRING: "Shared Port Adapter(SPA) Bay"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.53 = STRING: "2-port Gigabit Ethernet Shared Port Adapter_V2"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.54 = STRING: "Shared Port Adapter(SPA) Port Slot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.55 = STRING: "Shared Port Adapter(SPA) Port Slot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.56 = STRING: "Shared Port Adapter(SPA) Bay"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.57 = STRING: "Shared Port Adapter(SPA) Bay"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.58 = STRING: "Shared Port Adapter(SPA) Bay"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.59 = STRING: "host__DtrCard_Tcam3"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.60 = STRING: "host__DtrCard_Tcam2"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.61 = STRING: "host__DtrCard_Tcam1"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.62 = STRING: "host__DtrCard_1.2Vs2"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.63 = STRING: "host__DtrCard_1.2Vs1"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.64 = STRING: "host__DtrCard_Wwolf"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.65 = STRING: "host__DtrCard_PLL"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.66 = STRING: "host__DtrCard_0.75V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.67 = STRING: "host__DtrCard_1.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.68 = STRING: "host__DtrCard_1.8V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.69 = STRING: "host__DtrCard_1.25V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.70 = STRING: "host__DtrCard_2.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.71 = STRING: "host__DtrCard_Sonet"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.72 = STRING: "host__DtrCard_3.3V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.73 = STRING: "host__DtrCard_12V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.74 = STRING: "host__MB_Tcam3"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.75 = STRING: "host__MB_Tcam2"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.76 = STRING: "host__MB_Tcam1"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.77 = STRING: "host__MB_1.2Vsupply2"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.78 = STRING: "host__MB_1.2Vsupply1"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.79 = STRING: "host__MB_CPU_1.3V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.80 = STRING: "host__MB_PLL_1.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.81 = STRING: "host__MB_0.75V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.82 = STRING: "host__MB_1.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.83 = STRING: "host__MB_1.8V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.84 = STRING: "host__MB_1.25V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.85 = STRING: "host__MB_2.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.86 = STRING: "host__MB_3.3V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.87 = STRING: "host__MB_12V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.88 = STRING: "host__Mbus5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.89 = STRING: "host__InletTemp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.90 = STRING: "host__HotTemp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.105 = STRING: "spa0__3.3V_AUX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.106 = STRING: "spa0__12V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.107 = STRING: "spa0__1.2V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.108 = STRING: "spa0__1.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.109 = STRING: "spa0__2.5V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.110 = STRING: "spa0__3.3V"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.111 = STRING: "spa0__DownStream_Temp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.112 = STRING: "spa0__UpStream_Temp"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.113 = STRING: "GE SX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.114 = STRING: "GE SX"
The "sh power status power-supply" isn't available, but I do have the following:
#show env power-supply detail
                      48V       Current
R/S/I     Module      (V)           (A)
0/24/*    PEM1         52             8
          PEM2         52             8
    Total Power Supplies:                  2200W
        PEM Description Watts
        PEM1 Smart AC    1100
        PEM2 Smart AC    1100
    Redundant Power Supplies:              1100W
    Worst Case Power Used:                 1125W
     Slot Description                                        Max Watts
        0 Cisco 12000 Series Performance Route Processor            60
        1 Cisco 12000 Series - Multi-Service Blade                 250
        2 Cisco 12000 Series - Multi-Service Blade                 250
        3 Cisco 12000 Series SPA Interface Processor-              240
       17 GSR 12404 Consolidated Fabric/Alarm Card                 117
       24 Alarm Board(404)                                         208
    Worst Case Redundant Power Available: None
    Worst Case Total Power Available:      1075W

What power supply do you recommend?

Well i've been having quite a few problems with my upgrade of late and I suspect that it maybe due to my "oldish" power supply. I have an Enermax 350W power supply.
What do you guys/gals advise that I get?

OMG, I think I just had my first low_12V_amp_PSU_symptom!
http://techrepublic.com.com/5100-6255_11-1041735.html Told me something about bad (or too low powered PSU's):
The symptoms
Just about any intermittent problem can be caused by a faulty power supply. I normally look there first when the symptoms are a little weird. Common power-related symptoms include:
* Any power-on or system startup failures or lockups
* Spontaneous rebooting or intermittent lockups during normal operation
* Intermittent parity check or other memory-type errors
* HDD and fan simultaneously failing to spin (no +12V)
* Overheating due to fan failure (!)
* Small brownouts that cause the system to restart
* Electric shocks that are felt when the case is touched
There are also some obvious clues that should lead you to suspect a faulty power supply. These include:
* A system that is completely dead (nothing happens when the system is turned on)
* Smoke
* Circuit breakers popping when the PC is turned on
My problem was: CPU.temp @ 81 oC in CoreCenter that sounded the alarm and eventually shut down the pc. (First I didn't notice the alarm, I was checking out SimCity4 and thought it was part of the game )
Since the +12V rail handles the power of HD-motors and fans (http://www.cooltechzone.com/index.php?option=content&task=view&id=444&Itemid=0&limit=1&limitstart=1), I'm now afraid the CPU-fan didn't catchup when I increased the CPU load because it did not have the +12V power to do so!? Is this possible at all?
Maybe I'll follow SAB's advice and go through the hassle of changing my Zalman PSU for a Tagan TG480-U01 480 watt at my webshop....

Is My Power Supply Failing?

I installed Battlefield 3 on my 2008 MacPro under BootCamp and I could only play two minutes into the first mission as the screen goes blank, I get a sort of 'zap' noise and the computer reboots. I stopped playing that game and installed Modern Warfare 3 which I played all the way through in Standard mode. I few days ago I tried to replay it in Expert mode and the same thing happened. It seems as if this happens when the video card (a GTX285) is stressed. I contacted EVGA and they said it may be a failing power supply and suggested I try a different power supply which is not practical.
Is there any way I can check my power supply by somehow putting on test and stressing it?
Thanks
Alan

Did you install the latest Nvidia driver? EVGA Precision?
Thermal fan control under Windows is pretty much lacking and your system, esp. FBDIMMs can also get warmer than you want.
And make sure your aux power cables are both good first.
Sure you can run a number of Windows stress tests. PRIME, Intel
http://forums.tweaktown.com/gigabyte/30530-latest-overclocking-programs-system-i nfo-benchmarking-stability-tools.html

XFX 8800GT in a Mac Pro - how to connect to the power supply

I want to install a XFX Geforce 8800GT in a 2008-Mac Pro (running Vista only; no boot camp). Where can I get the necessary power cable to connect the card to the Mac?
I know that there are two non-standard(?) 6-pin power connectors on the main board, which are meant to connect those “booster cables” to. I know that these cables are available via mail order (e.g. from ATI for approx. $13). I also know that Apple’s support is not very helpful with questions around non-supported hardware.
*Here’s the problem:* Instead of two 6-pin molex connectors this card has only one, but requires the use of a special Y adapter to connect to two 4-pin molex plugs (as seen here: http://www.com-tra.de/img/p/06759_o.jpg).
*My question:* What is the proper way to connect this graphics card to the machine? Is there a matching cable available somewhere? Could I perhaps simply use two booster cables and a 6-pin molex Y-adapter? What about getting the power from somewhere else, e.g. optical drives?
Any help is much appreciated!

It depends on whether XFX's GeForce 8800 GT is overclocked and what the demands of the fan assembly might be.
It's really easy to find out. When I just connected one power feed to Radeon HD 3870 X2, it didn't show up to Vista 64 (while the Radeon HD 2600 XT which was also installed was clearly recognized).
I shutdown, added the second power lead, and powered up. This time it showed up.
Also, sometimes you will get an audible alarm if the card is deficient on power - especially if it's the only GPU installed.
In the case of the HD 3870 X2, instead of a "Y" connector, I used both Apple proprietary power feeds that were connected to the motherboard's PCIe 6 pin power sources. You can use an external power source (like an ATX power supply) if you run short of power sources but then you can't put the side cover on.

T400 shake display when plug power supply s.o winxp

Hello everybody
Days ago I installed windows XP prof to thinkpad T400 , I used driver Intel Display Driver for Windows XP and ATI Display Driver for Windows XP but sometimes when plug power supply suddenly display start shake. please help me about of this
thanks a lot

Ok, as an electrical engineer...I have to step in here! LOL
First, these amp rating are for 2 +12 rails. That is why you see a protection of around 15-18A on the +12 rail. That means each Rail is allowed up to 18A lets say for the new Enermax 1.2 version like the one I have.
Now, Lets say 18A for 12V....well as you know the Abit NF7-S uses the 12V for powering the CPU.
Lets say you have a Barton like me and you want it stable at around 2.4-2.5Ghz. You will have to put lets say around 2V to the cpu to get it stable at that kinda speed, specially if you have high FSB like I do. So 12V * 18Amps = 216W ....well the converter on the NFS-7 is really bad, its loss on the step down convertion is probably around 25% along with the PSU lost cuz its not running at 25oC (another 15%)....you will actually only get around 100-120W for the CPU.
Now, if you go into Sandra and see how much a Barton eats up at 2.4Ghz you will see its around 110Watts.
So, if you wanna push more, dont even think about it! Prime Power test fails and your +12 rail will drop as low as 11.60 Volts.
Now, lets say you got yourself a AMD 64 bit chip and you wanna overclock it....I bet it will need more than 110Watts.
So, what im saying is, dont buy nothing less than a 500 Watt PSU!
You really need around 20-22 A on the main +12 along with really really good cooling on the case and PSU so it is running at a 100%.
http://forums.amdmb.com/showindex.php?s=&threadid=287828
i found this quite interesting especially the bit re the power loss turning the 12v into 1.6v or what ever cpu needs

Prime 2.2 Power supply alarms

Similar Messages

Maybe you are looking for