Printing Paper Question--Are Creases OK?

I'm sorry because I'm sure I should ask this question in the forums of the Canon MX870 printer, because that's my device, but I really would like your opinions here. I like to recycle paper through my printer (old office paper and junk mail that still has one clean side for example) for printing needs around the house that typically just get read a time or two and then tossed. No need for archival quality printing and pristine paper.
I am just wondering if it is OK to use previously folded paper in my printer? I get lots of junk mail that has a couple of creases in it but still has a clean side that can be used for printing. Might the creases hurt the inkjet mechanism in my printer? I don't want to take the risk of damaging my printer just to recycle a few extra sheets of paper here and there.
Thanks for the input,
Steve M.

Thanks Bruce. That sounds promising. I might be helping my printer stay clean if I use creased paper in it! I'll definitely try to look that up in my documentation.
Regards,
Steve M.

Similar Messages

HP Photosmart 2610 All in One Printer Paper feeds OK but the software and sensors are a problem

HP Photosmart 2610 All in One Printer Paper feeds OK but the software and sensors are not allowing paper to feed until several steps are taken first.
(I am using Windows 7. I also use the virtual XP mode and mostly MS Office 2003 docs).
I have had this printer for several years and love it. Before I toss it out, I thought I would check if I could get it to work properly before I buy another printer. Note: I did put in a new HP black cartridge (because it was out of ink) but the printer was not working properly for several days before I changed the cartridge. The printer was at step 5 before ink change.
Lately, each time I turn on my printer, I have to go through the same routine
1. The printer wants to align the cartridges so I push OK
2. The paper feeds into the printer and stops at the exact place to start printing.
3. Error message appears that it is out of paper. So I press OK to continue.
4. It says "aligning print cartridges" runs through 2 sheets of blank paper without trying to do anything and then states "cartridge alignment failed" "Press OK to continue"
5. Screen is now normal and it appears it is going to work.
6. It makes no difference if I used the copy function OR when I send a print job from the computer, the paper feeds into the printer and stops at the exact place to start printing but nothing happens.
7. Error message appears that it is out of paper. OR that it is the wrong size paper. I pull the paper that was at the proper place to be printed from the printer and then the error message says "Paper jam. Press OK to continue"
8. I press OK. The printer will then quickly feed in and eject 2 sheets of paper before it will actually start printing the print job. It will work fine after this as long as I print from the same document.
9. If I want to print a different document then I have to start all over again at step 6 to get the printer to work. If I shut the printer off I have to go back to step 1.
What I have already tried
A. Uninstalled and reinstalled the printer driver direct from HP web site. I have done this several times with both the basic driver download and the complete package download.
B. I have done a partial reset by unplugging the printer, and then re-plugging the printer while pushing the "# and 3" buttons while turning on the printer. I have done this several times. Each time it will work fine until I try a different document of turn off the printer.
C. I have downloaded the HP Print and Scan Doctor and used it several times. It states that "everything checks out OK"
D. I have downloaded the HP Hardware Diagnostic Utility 4.0 but it does not work with my printer.
E. I have cleaned all the rollers and blown air throughout to make sure there were no bits of junk in the paper's path or blocking a sensor.
F. I have tried different brands and weights of paper (all 8½ x 11) but nothing works.
Most of the problems started when I added the printer to the virtual machine so I could print XP files. This may just be a coincidence because the printer has the same problems when I use the copy function without the computer being on.
Thanks for looking at my issues. Any help would certainly be appreciated.

I just tried using Notepad as you suggested and had the same result. Paper feeds in stops at proper place and error message "out of paper"
I just put in two new HP ink cartridges because the other two were low and I was told that this might be the problem.
I seem to remember that the HP 2610 shows 2 "ink icons" in the lower left corner. One for black and one for color. The ink icons would change from completly full to just an outline as the amount of ink went down. Currently the black ink icon is missing
This is a very frustrating problem because the printer works great after doing a few steps to get around the problem. The fact that the problem reoccurs any time anything is changed is the major problem
Most of the problems started when I added the printer to the Windows 7 virtual machine so I could work with Windows XP programs. This may just be a coincidence because the printer still has the same problems when I use the copy function without the computer even being on.
I want to thank you for all of your efforts. Perhaps this is a unique problem that will never be solved and it is best to take my losses and buy a new printer. As a last chance, if possible, could you refer my post to someone who is an expert with the HP 2610 printer.

Where are printer paper profiles stored in Mavericks?

In previous versions of OS X, I could find where my printer paper profiles were stored. I have some test paper profiles that don't work and I want to delete them but I can't find them in Mavericks 10.9.2 I have done a search for their name but apparently they are hidden although they show up in Photoshop and the Printer dialog box. What and where is the folder I need to look in? Thanks for your help.

~/Library/ColorSync/Profiles

I need to print save the date magnets that are 8.5x5.5 but I can't seem to align the printer / paper

I need to print save the date magnets that are 8.5x5.5 but I can’t seem to align the printer / paper to print correctly!! HELP!

Please read this post then provide some details. What printer model? What operating system? What program are you using to print?
How thick are the magnet sheets? I would expect most printers would have trouble feeding this material.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP D5460 printer. Colors are bad on photo paper.

HP D5460 printer. Colors are bad on photo paper,, OK on plain paper. New genuine HP cartridges. It used to work fine. Have tried aligning print head. Have tried "automatic" and "best" for print quality. Doesn't matter.
Vista 64 bit OS

Besides using genuine HP ink cartridges, check this document:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=bpu03037&cc=us&dlc=en&lc=en
007OHMSS
I was a support engineer for HP.
If the advice resolved the situation, please mark it as a solution. Thank you.

When I print a selected area of web page, it doesn't fit to the paper. The end of each page are cut off. Is there any solution?

When I print a selected area of web page, it doesn't fit to the paper. The end of each page are cut off.
I'm very sure my printer is set cirrectly.
Can't Firefox shrink to fit when I want to print a selected area of web pages?
This has never occurred in IE.

File >Page Setup -- check your margins, I have set size to 85% which is probably left over from some problem. Also check your printer that it is correctly set to the size of the paper.

HP Photosmart Premium C310a Printer paper alignment and paper feed problem.

Standard Info:
HP Photosmart Premium C310a Inkjet All-in-one Printer.
Windows 7 Home Premium
No reported errors messages except for paper jams.
No changes were made to the system before the problems began.
My Info:
I am very proficient with computers and electronics. I would first like to say that this printer has very vibrant inks and its ColorSmart/sRGB ICC profile is pure magic. The high DPI ratings have turned out to be accurate so far and the printer prints beautiful images.
Problems:
The problem I am having is with the printers paper feed rollers. They are not scrolling the paper through the printer accurately and consistantly. There have also been two paper jams when using multipurpose everyday paper. When printing high res artwork using HP Advanced Photo Paper I was using HP Photosmart Essentials to create an 8"x10" picture on the 8.5"x11" paper and the first 35-40 prints came out accurately but then, before any paper jams or other problems the 8x10 pictures began to not center correctly on the paper. Then the top of the 8x10 picture started slanting to the right on the paper and extending too close to the right edge of the paper. The entire 8x10 picture is no longer printing 8x10 (the left side of the picture is just over 8" tall and the right side of the picture is printing just under 8", same thing with the top and bottom edges of the image) and is not centering properly on the paper. I just had my second paper jam last night which I clicked the "cancel print" button on the front of the printer touch display to eject the paper. Immediately after, everything began printing very close to the left edge of the paper and prints at an angle down the sheet no matter what it is that I print or what paper it is printed on. I have tried using the auto alignment feature on the printer several times and it does not help.
Questions:
Is this printer purchased on 09/25/2011 from hp.com (with no extended warranty) still under a regular warranty?
If I send it in for repairs will HP be able to fix these problems?
Is there any way that I can adjust the scrollers myself to fix the problem?
Is the new C510a more reliable than the C310a in this field?
I need a backup printer for my art business, I would like to purchase an HP C510a, but am concerned I will have the same problems with the new one.
If anyone can help, please respond. I cannot go on with these problems any longer.
Thank you for your time,
Nanette

Thank you for your quick response Bob. Your answer was helpful, but did not solve my problem. I have cleaned the printer exactly as your response has suggested, but there has been no change, and I was not able to find any dirt, scum, dust, or anything at all wrong with the rollers.
Here are a few pictures of some 8"x10" pictures that I just printed on 8.5"x11" HP Advanced Photo Paper:
These 8"x10" images are supposed to be centered on the paper, but are FAR from centered or dimensionally accurate to 8"x10".
This last image shows really well how the top of the 8"x10" image slants downward from left to right as well as approaches too close to the right edge of the paper.
Is this a problem that I can fix on my own?
If I send the printer to HP for repairs will they be able to fix this problem or will they just clean the printer scrollers and send it back thinking it is fixed?
I really need help with this problem, because right now, the printer is not useable.
Thank you for your help.
-Nanette

Epson R2880 - Will not print - paper sizes

I am having major problems with trying to print to a R2880. I have recently purchased it and have had problems with printing to it from the beginning. Sometimes it works but mostly it doesn't.
The Epson driver is 6.2 which is the latest. I am running Leopard. Do not want to upgrade to SL cause what I read shows FCS2 does not run on it.
Keeps on telling me that the "Paper source selected in the printer doesn't macy the paper loaded in the printer" which is of course bollocks.
I have tried the solution offered by a previous post which was to got to the print preview and then Cmd - P and then choose the right paper. Worked fine on an A4 but when I did the same for a 10 x 15 cm no go.
It suddenly started working the other day but when I chose a selection of 10 x 15's (varied portrait / landscape aspects) to print it did not orientate them correctly. The paper was installed in a portrait arrangement yet not one of the photos printed on the page correctly.
What a waste of time this printer and Aperture are.
Can anyone help on this most frustrating problem. I have had this printer for a few months and have only managed to print a handful of photos !
Regards

Hi Colin,
The R2880 is a little finicky when it comes to paper source. A couple of questions:
• What paper are you using? What size? Are you using the back tray or the main tray? I had a ton of problems with the back tray and that very error. I now always use the main tray, but it depends on the paper you use since certain types can only be loaded in the back.
• Are you making sure the preset you choose is for +sheet feeder+ and not +roll paper+?
The Preview solution you read about is probably mine and was brought on by SL. Fortunately 10.6.2 fixed that problem but I've still had the paper source error come up a couple of times - I need to open the print settings for the preset I want to use and save it again (it's as though it needs to be reminded that it should use the sheet feeder, even though that setting is saved right there in the preset).
My first thought was that your problem might have to do with the non-conventional paper size, but I also make custom 16x12 prints on 13x19 paper and don't have problems at all.
I'm guessing it's probably a combination of settings and paper type...

Black Bars on printed paper - PLEASE HELP -PICTURE INCLUDED.

Where even I print, black bars on papers appear on the printed paper making it impossible to read whats printed.
I will include a picture
Printer details -
Canon Lasershot LBP 2900
PICTURE OF BLACK BARS ON PRINTER -

1. Open Premiere Elements 8.0.1 and set the project preset (new project dialog) = PAL AVCHD Full HD1080i25.
2. In the program, Edit Menu/Preferences/General, have a check mark next to "Default Scale to Frame Size".
3. Right click the Edit Mode Monitor, select Magnification, and have the set on "Fit".
4. Using Premiere Elements' Get Media/Files & Folders, import your AVCHD 1920x 1080 16:9 video into the program. (You will see your video in the Organizer.)
5. Drag your video from the Organizer to the Timeline. Are you seeing a 4:3 version of it in the Edit Mode Monitor?
6. If so, click on the Project Tab in the row below the active Organize (Blue) Tab to bring up the Project Media View.
7. In the Project Media View, right click your video in the list to bring up the Interpret Footage dialog.
8. In the Interpret Footage dialog, under Pixel Aspect Raio, dot the "Conform to:" and change the setting = Square Pixels (1.0). After you click OK to that, see what your video now looks like in the Edit Mode Monitor.
Miscelleanous
1. You can also use the Interpret Footage dialog for Frame Rate considerations.
2. Although the gspot read out does not give a reading for PAR (Pixel Aspect Ratio), the PAR can be calculated from the SAR and DAR values given since PAR = DAR/SAR and, in your case, 1.778/1.778 = 1.0. The DAR is Display Aspect Ratio and the SAR is Storage Aspect Ratio.
3. What is the duration (seconds, minutes, hours) of the video that you have been trying to use in Premiere Elements 8.0.1. You are working with AVCHD which is a very resourve demanding format, and it appears that you have 2 GB RAM installs that probably translates in much less available and you do not say how much free hard drive space your computer has. But, if the video in question is only of a few seconds duration, we should be able to work through this pixel aspect ratio issue.
courtesy of AT Romano...

HP LaserJet 200 color M251nw prints, but images are blurred.

Laserjet200 (HP LaserJet 200 color M251nw) prints, but images are blurred; sometimes the entire page and other times just the right half. Staples tech said the drum could be bad. Can this be corrected? Using W7 ultimate OS.

Hi @jimmanning ,
I see by your post that the images are blurred. I would like to help you.
Run a calibration on the printer.
On the printer touch the wrench, system setup, print quality, color calibration calibrate now.
Print a Diagnostics Page to see if you have the same results. Trying to determine if it is a hardware or software issue.
Go to Setup, Reports, arrow down and select Diagnostics Report.
I have provided a document with more steps for running a cleaning and checking print driver settings.
Troubleshooting Print Quality Issues.
Remove the toner and check to see if there is any toner on drum.
Make sure the paper type is selected to the media that you are using, not the default setting unspecified.
Please provide the following information so I can assist you better.
What were the results of Diagnostics Page and Print Quality Page?
Are you using Genuine HP Toner?
What are the Ink levels?
Was there any damage on the toners?
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

How do you change the page format to print a larger area?

Hi there, another new to mac and new to numbers guy.
I'm trying to find the windows equivalent to change page format.
I want to reduce the blank border surrounding my table and print a larger area. How do you reduce the blank border that prevents you from printing up to the paper edge?
cheers

Page margns in Numbers are set in the Layout Inspector.
Open the Inspector and click the Layout button.
Edit the four margin settings as you wish. Reduce the (page) header and footer settings to zero if you don't want to include running headers or footers on your pages.
Note that margins will be limited by the capabilities/settings of your printer. Printing to the edges of the paper usually requires a choice to be made in the Print dialogue as well as for the document itself.
Regards,
Barry

Help with printing photos on photo print paper with Desk-jet 3050A

Hello I am in need of some advise regarding my desk-jet 3050A printer, the problem is that I cant seem to print pictures on to my glossy photo print paper; I can print pictures onto standard A4 plain paper but the pixels have blurred slightly.
I cant seem to find any accurate advise regarding which photo printer paper is compatible with my printer and how to actually print a picture onto both plain paper/photo paper at a good quality, any help would be appreciated, let me know if you need anymore information. Thanks
Chris
OS: Windows 7 Home Premium 64-bit
Make: HP Desk-jet e-All-in-one Printer
Model: J611a series 3050A
Product serial No: {Removed for privacy}
FPU No: CR231-64001

Hi,
What exactly is going wrong? and with the link below you can find the specs of the printer. Under paper handling the sizes and paper weight that are supported are listed.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02105426&tmp_task=prodinfoCategory&cc=us&dlc=en...
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Although I work for HP my posts and replies are my own
Please mark the post that solves your problem as "Accepted Solution"

Canon pixma pro 9500 having problems with my print out. colors are glazed and missing colors

canon pixma pro 9500 having problems with my print out. colors are glazed and missing colors
i have prfiled the mac and printer wiht colormunki and uplodated the profile sucessfully
i set the printer to correct icc profile
print out comes out same with glazed colors and missing tones/colors
however when i use the same printer on windows and with light room, following same icc profile, colormunki calibrated profile, the print our are excellent.
i have also tried using printer manage profile using the Mac and Aperture and get same poor prints
can you please assist and thanks

I've a Pro9000 and also use Colormunki successfully.
When I use Colormunki, I calibrate both of my monitors and the printer/paper combination. Colormunki saves the generated profiles to the correct places -- I don't load or change any profiles after that as that would mess-up what the Colormunki had just done for me, and this would likely mess-up the prints.
Though I double-check the settings in the print dialogue, the choice for the printer handling things is already grayed-out. Colorsync handles it all just fine.

Iphoto 9.6.1 deleted printer paper choices (Canon Pro 100)

Hello,
I fear the iPhoto 9.6.1 update may have other issues with printers beside freezing, and would appreciate any suggestions -- otherwise, I'm passing on some information.
Using a MBProRet 15" with OS X 10.10.2 and a Canon Pro-100 hardwired connection (not wi-fi), I have installed iPhoto 9.6.1 yesterday and, today, in addition to suffering some printer freezes, I no longer have all the Canon paper choices that were available with the Print command pre 9.6.1 -- fine art paper, platinum, luster, matte, and all the others are gone, deleted, just not there any more in iPhoto. The Canon paper choices are still available in Aperture 3.6 (and even MS Word 14.4.8!). I have not installed any printer software updates recently.
Unfortunately, I didn't realize this until I had spent some 5+ hours earlier today re-organizing my library which will be lost if I restore the library from TM. Since I can still print quality paper from Aperture it's not a total disaster, but ... an aggravation.
Hopefully this isn't a sign of what's to come with the New & Improved Photos. Is there a permanent Opt-Out available?

Try the directions in this Apple document: OS X Yosemite: Reset the printing system

CHECK PRINTING PAPER

HI SIRS
JUST FOR KNOWLEDGE I WANT TO KNOW THAT WHO GIVES CHECK PRINTING PAPER?
IS BANK PROVIDING THE SAME PAPER? WHAT DETAILS WE NEED TO FILL IN THAT?
IF THE PAYMENT DOCUMENT IS MORE THAN 1 THEN HOW WE MANAGE?
THANKS IN ADVANCE!!!!!

Hi,
Please use Lowe Case..
Pre Printed Cheque Stationary is issued by bank. It can be of a format as required by your client. ie: it can be either only the cheque which is continous or Cheque *** advice which is again continous.
Now, your second question, as to what happens, when the advic eis more than one page, in that case, any spill over from the main page is printed on a separate sheet of paper.
In F110 where you maintain Variant, you have the option of ticking what you want the system to print.. Cheque Summary, Cheques and Payment Advice.
Do let me know if you need any further clarity..
Regards,
SAPFICO

Printing Paper Question--Are Creases OK?

Similar Messages

Maybe you are looking for