Problem about ccm based silence monitor(UCCE)

Now I successfully configured the ccm based monitor.But there is still a problem.
When the supervisor is listening,there is a "du~"voice can be heard in the agent phone in every 10 seconds,and it last for 1 second.
The problem is critical cause the agent would know that he is monitored by the supervisor.
So is there anyone has the same problem with me?and how to solve it?
Sent from Cisco Technical Support iPad App

Could you post complete version details of
1. UCCE
2. CUCM
3. Is it CAD or CTIOS ? Version ?
GP.

Similar Messages

The Problem about Monitoring Motion using PCI-7358 on LabVIEW Real Time Module

Hello everyone,
I have a problem about monitoring the position of an axis. First let me give some details about the motion controller system I’m using.
I’m using PCI-7358 as controller and MID-7654 as servo driver, and I’m controlling a Maxon DC Brushed motor. I want to check the dynamic performance of the actuator system in a real time environment so I created a LabVIEW function and implemented it on LabVIEW Real Time module.
My function loads a target position (Load Target Position.vi) and starts the motion. (Start.vi) then in a timed loop I read the instantaneous position using Read Position.vi. When I graphed the data taken from the Read Position.vi, I saw that same values are taken for 5 sequential loops. I checked the total time required by Read Position.vi to complete its task and it’s 0.1ms. I arranged the loop that acquires the data as to complete its one run in 1ms. But the data shows that 5 sequential loops read the same data?

Read Position.flx can execute much faster than 5 ms but as it reads a register that is updated every 5 ms on the board, it reads the same value multiple times.
To get around this problem there are two methods:
Buffered High-Speed-Capturing (HSC)
With buffered HSC the board stores a position value in it's onboard buffer each time a trigger occurrs on the axis' trigger input. HSC allows a trigger rate of about 2 kHz. That means, you can store a position value every 500 µs. Please refer to the HSC examples. You may have to look into the buffered breakpoint examples to learn how to use a buffer, as there doesn't seem to be a buffered HSC example available. Please note that you need an external trigger-signal (e. g. from a counter of a DAQ board). Please note that the amount of position data that you can acquire in a single shot is limited to about 16.000 values.
Buffered position measurement with additional plugin-board
If you don't have a device that allows you to generate a repetitive trigger signal as required in method 1.), you will have to use an additional board, e. g. a PCI-6601. This board provides four counter/timers. You could either use this board to generate the trigger signal or you could use it to do the position capturing itself. A PCI-6601 (or an M-Series board) provides can run a buffered position acquisition with a rate of several hundred kHz and with virtually no limitation to the amount of data to be stored. You could even route the encoder signals from your 7350 to the PCI-6601 by using an internal RTSI cable (no external wiring required).
I hope this helps,
Jochen Klier
National Instruments

CCMS agents, alert monitoring, SNMP traps

Hi Guys,
I have a question. There is a requirement about monitoring. Any documenation or links will be really appreciated.
My client needs me to use CCMS agents, alert monitoring for both ABAP and JAVA stacks, SNMP traps, sending SNMP traps, interface CCMS with third party monitoring tools. Mostly, the ,monitoring is done thru RZ20.
Anybody can point me in right direction or material.
Thanks
Venky

Hi,
Check these CCMS Weblogs. Really good ones...
/people/federico.babelis2/blog/2006/04/26/ccms-rule-based-monitors-configuration-guide-for-dummies
/people/aravindh.prasanna/blog/2005/12/23/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part--1
/people/aravindh.prasanna/blog/2006/02/20/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part-3
Feel free to revert back.
--Ragu

CCMS for Table monitoring not using Message Class

We are currently using a Table content monitor in CCMS to raise alerts for an ABAP monitoring program we have written. The program inserts records in a custom ABAP table and when a row is inserted with a certain value we raise an alert through CCMS.
The data collection method is using the "Red" function module SCSM_GEN_TAB_DS_R
The alerts are generating fine but the alert text is displaying <CCMS: no default text available>. We have configure a message class and number but it is not displaying this in alert. Does anyone know what could be the problem?
Here is the parameter settings for the data collection method
1. TARGET_TABLE           ZTSPM_CH_STATUS
2. FIELDNAME              CHANNELKEY
3. FIELDVALUE             CCSTATUS
4. MAXROW                 50
5. WHERECLAUSE1           CCSTATUS = 'FAIL'
6. WHERECLAUSE2
7. WHERECLAUSE3
8. TOP_FULL_NAME
9. RESCANFROMBEGIN        REPORTTIMESTAMP
10. T100_MESS              ZXI_CNB 023
The message class/number (ZXI_CNB 023) is
"Connectivity Heartbeat failed for &1, Status: &2"
I was expexting the values from the table for fieldname (CHANNELKEY) and Fieldvalue (CCSTATUS) to be replaced in the message string.

Hey Mark!
I had a question about this topic. I had the problem, that method doesn't work. The following parameters have been set:
1. TARGET_TABLE           ZMON_ERROR
2. FIELDNAME              EF
3. FIELDVALUE             EV
4. MAXROW                 50
5. WHERECLAUSE1           EV='AU01'
6. WHERECLAUSE2
7. WHERECLAUSE3
8. TOP_FULL_NAME
9. RESCANFROMBEGIN
10. T100_MESS
Rescanfrombegin and Messageclass have not been set, because I read, that there are many problems.
In Technical Export Monitors under DataSupplier theres an alert:
Internal Error in method SCSM_GEN_TAB_DS_R, Error: SELECT, SY-SUBRC = 0.
I think the problem is the WHERECLAUSE, but it doesn't matter if I change everything. Do you know any solutions, maybe?

A problem about calling Labview vi in VB

Hi all:
I meeting a problem about data transfer and parallel operation between VB and Labview.
Actually, I want develop a VB program, in which, the Labview VI can be called and corresponding parameters can be transferred to Labview. and then, I also can operate my system by VB program at same time. something like parallel operation (VB and Labview program).
But the question is :
1. If I use "Call" method of ActiveX in VB, and the LabVIEW subvi is not stopped (for example, a loop structure), I can not do parallel operation on VB program. The error message is "other application is busy" which is attached below. The sample codes is also attached.
2. I tried to use other methods like "OpenFrontPanel" and "Run", but I am not sure how to transfer the parameter??
3. Then I tried to use "SetControlValue" to set the parameters, but there is a error " := expected", which is very strange, because the statement I wrote is followed with the help documents [ eg: VI.SetControlValue ("string", value)], why it is still need a "=" ??
Does anybody know something about it? Thanks a lot
Message Edited by hanwei on 11-07-2008 03:18 PM
Attachments:
vb_labview_error_message_1.JPG ‏14 KB
VB_to_LV.zip ‏10 KB

I sure hope OP has solved it by now.
/Y
LabVIEW 8.2 - 2014
"Only dead fish swim downstream" - "My life for Kudos!" - "Dumb people repeat old mistakes - smart ones create new ones."
G# - Free award winning reference based OOP for LV

The problem of function-based reuse

I read the quoted text as follows from a book authored by a Microsoft developer. I googled and found a lots of quotes of it, but did not find any explanation.
============
With languages like C, the basic unit of reuse is the function. The problem with function-based reuse is that the function is coupled to the data it manipulates. and if the data is global, a change to benefit one function in one reuse context damages another function used somewhere else.
============
C uses libraries widely,which is of function-based reuse. Can anybody kindly give me a scenario when this problem happens?
Java is typically object-based reuse, and I admit that my question is not a Java one. But I feel it would help to understand more about the concept or benefits of design of Java language. So, thank you to allow me to post this question here,
Edited by: 799160 on Sep 30, 2010 12:38 PM
Edited by: 799160 on Sep 30, 2010 12:57 PM

This is what I got out of reading the quote you posted:
I suppose something like the following could happen:
You (being a general person) have been given a class to modify. You look at the code for the first time and it has a bunch of methods and some class variables in it. Some of the methods use the class variables. How can you be sure if you change the functionality to change a class variable in one method won't affect the other methods when they are used? This problem can be solved by learning what everything does, how it interacts and the correct way to use it. But then again, if you don't think about it and just make changes...Oops!
Perhaps another abstract example would make sense:
Imagine a calculator that could be used by 2 people at the same time? I bet it'd come up with some funny answers :)
I wrote up a short example of this, hopefully it makes some sense:
public class SuperBigProgram
     private int globalVar;
     public static void main ( String[] args )
          new SuperBigProgram();
     public SuperBigProgram()
          System.out.println("I'm a super big program.");
          globalVar = 0;
          //Let's pretend these series of events occur during the program:
          doItHighChanceActivity(); //1
          doItHighChanceActivity(); //2
          doItHighChanceActivity(); //3
          //Whoops super rare event occured!
          doesNotHappenALot();
          doItHighChanceActivity(); //4????    but is really 5.
      * This happens A LOT!
     private void doItHighChanceActivity ()
          superUtilityMethod();
          System.out.println("globalVar: " + globalVar);
      * This utility method does some awesome utility stuff for our Super Big Program.
      * This changes some global data.
     private void superUtilityMethod()
          globalVar++;
      * This does not happen a lot, if at all.
     private void doesNotHappenALot()
          //Hey I don't happen a lot but I'm reusing this really cool utility method that contains global data...
          //Code reuse for the win!
          superUtilityMethod();
}Here is the output:
I'm a super big program.
globalVar: 1
globalVar: 2
globalVar: 3
globalVar: 5
Edited by: kilosi on Sep 30, 2010 1:22 PM

Hello apple I have the problem with my iPhone and my friends have this problem too. My iPhone have the problem about calling and answer the call. When I use my iPhone to call I can't hear anything from my iPhone but the person that I call can answer it bu

Hello apple
I have the problem with my iPhone and my friends have this problem too.
My iPhone have the problem about calling and answer the call. When I use my iPhone to call I can't hear anything from my iPhone but the person that I call can answer it but when answer both of us can't hear anything and when I put my iPhone to my face the screen is still on and when I quit the phone application and open it again it will automatic call my recent call. And when my friends call me my iPhone didn't show anything even the missed call I'm only know that I missed the call from messages from carrier. Please check these problem I restored my iPhone for 4 time now in this week. I lived in Hatyai, Songkhla,Thailand and many people in my city have this problem.
Who have this problem??

Apple isnt here. this is a user based forum for technical questions. The solution is to restart, reset, and restore as new which is in the manual after that get it replaced for hard ware failure. if your within your one year warranty its replaced if it is out of the warranty then it is 199$

Problem with File Based replication in Weblogic Express 10

Hi,
          We have Web application (exploded war) file deployed on Weblogic Express 10, to a Cluster of three Managed Servers (all three on different physical machines).
          We are using File based session persistance in weblogic.xml
          We have a shared location for all the three servers where we will be sharing the Session data.
          When we start the application, its works fine and is very fast, but after sometime the application slows down.
          Troubleshooting the Issue we found that its a problem with file based replication. By using File based replication every user session is stored in form of directory inside shared directory. So after sometime thousands of directories are created inside the shared directory where the session information is stored. So when we access the application, its waiting for lot of time with Message Session Monitor .... (this is because its browsing through the shared session storage directory for lot of time for session information as it has lot of directories) and finally after a long time like 10 mins we get the Application Home Page.
          When we clean up all the saved sessions inside shared directory, the application works fine, But we will see the same sometime later may be after 3 or 4 hours when the shared session directory has lot of session information stored in it.
          Is there a way to clean up the saved session information on file system as soon as that user session is closed by using file based replication.
          We cannot used Inmemory replication as our Appl doesnt support it.
          Please advice as it is a major show stopper in our Production Mirror env.
          Weblogic Consultant

It is possible to reduce number of live session by configuring very low timeout-secs weblogic.xml. Default is 60 minutes.
          More details are here..
          http://e-docs.bea.com/wls/docs100/webapp/weblogic_xml.html#wp1071982
          Jayesh
          Yagna Sys

Problem about space management of archived log files

Dear friends,
I have a problem about space management of archived log files.
my database is Oracle 10g release 1 running in archivelog mode. I use OEM(web based) to config all the backup and recovery settings.
I config "Flash Recovery Area" to do backup and recovery automatically. my daily backup schedule is every night at 2:00am. and my backup setting is "disk settings"--"compressed backup set". the following is the RMAN script:
Daily Script:
run {
allocate channel oem_disk_backup device type disk;
recover copy of database with tag 'ORA$OEM_LEVEL_0';
backup incremental level 1 cumulative copies=1 for recover of copy with tag 'ORA$OEM_LEVEL_0' database;
the retention policy is the second choice, that is "Retain backups that are necessary for a recovery to any time within the specified number of days (point-in-time recovery)". the recovery window is 1 day.
I assign enough space for flash recovery area. my database size is about 2G. I assign 20G as flash recovery area.
now here is the problem, through oracle online manual, it said oracle can manage the flash recovery area automatically, that is, when the space is full, it can delete the obsolete archived log files. but in fact, it never works! whenever the space is full, the database will hang up! besides, the status of archived log files is very strange, for example, it can change "obsolete" stauts from "yes" to "no", and then from "no" to "yes". I really have no idea about this! even though I know oracle usually keep archived files for some longer days than retention policy, but I really don't know why the obsolete status can change automatically. although I can write a schedule job to delete obsolete archived files every day, but I just want to know the reason. my goal is to backup all the files on disk and let oracle automatically manage them.
also, there is another problem about archive mode. I have two oracle 10g databases(release one), the size of db1 is more than 20G, the size of db2 is about 2G. both of them have the same backup and recovery policy, except I assign more flash recovery area for db1. both of them are on archive mode. both of nearly nobody access except for the schedule backup job and sometime I will admin through oem. the strange thing is that the number of archived log files of smaller database, db2, are much bigger than ones of bigger database. also the same situation for the size of the flashback logs for point-in-time recovery. (I enable flashback logging for fast database point-in-time recovery, the flashback retention time is 24 hours.) I found the memory utility of smaller database is higher than bigger database. nearly all the time the smaller database's memory utility keeps more than 99%. while the bigger one's memory utility keeps about 97%. (I enable "Automatic Shared Memory Management" on both databases.) but both database's cup and queue are very low. I'm nearly sure no one hack the databases. so I really have no idea why the same backup and recovery policy will result so different result, especially the smaller one produces more redo logs than bigger one. does there anyone happen to know the reason or how should I do to check the reason?
by the way, I found web based OEM can't reflect the correct database status when the database shutdown abnormally. for example, if the database hang up because of out of flash recovery area, after I assign more flash recovery area space and then restart the database, the OEM usually can't reflect the correct database status. I must restart OEM manually to correctly reflect the current database status. does there anyone know in what situation I should restart OEM to reflect the correct database status?
sorry for the long message, I just want to describe in details to easy diagnosis.
any hint will be greatly appreciated!
Sammy

thank you very much, in fact, my site's oracle never works about managing archive files automatically although I have tried all my best. at last, I made a job running daily to check the archive files and delete them.
thanks again.

A switch on/off problem about the relay in a loop

hi group:
I am developing a project based the Ni-sci-1160. Now I meet a problem about switch on/off in a loop.
for example: I creat a loop, and continually check a boolean. if the boolean is true, then the realy is closed, otherwise the relay is open. The problem is when I make the boolean is true, the corresponding relay is not always on, but just on-off, on-off,on-off. I don't know why? Is there any good idea to fix it?
the easy example codes is attached here , thanks for you help.
Attachments:
relay_problem.vi ‏19 KB

Try moving that first DAQmx function out of the while loop. Since it is called switch set and Reset, I'm guessing it is resetting the status of the switch every iteration of the while loop which probably means setting it back to false. It looks like an initialization type of function which means it should only be run once.

I've got the problem about sharing the screen

Hi, i bought iMac 21.5 (Late 2013), i'v upgraded it to the Mavericks. I've got the problem about sharing the display, i have thunderbolt to hdmi adapter and while i plug it to my TV, it doesn't work, it has no signal on TV, can someone help me ?? Thank Yo

Hello Gukakila
Start your troubleshooting with the article below. Try out the cable on a different tv or monitor to see if it shows up there. You may also need to reset the SMC and Parameter Ram.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
Regards,
-Norm G.

Problem with replication based on materialized view

Problem with replication based on materialized view...
Given:
1. Source: S-1
2. Targets: T-1, T-2
3. DB links: from T-1 to S-1, from T-2 to S-1
Required replicate table TBL on S-1 to T-1, T-2 via db links.
On S-1 was created materialized view log with PK on TBL. On T-1, T-2 were created mat.views as "on prebuilt table refresh fast on demand". In case of get "ORA-12034: materialized view log younger than last refresh" or initial load - perform complete refresh. Initial load on T-1 takes about 1 hour, on T-2 - about 12 hours. Refresh is executed via job with minutely interval. If refresh is running then it is not performed.
Problem: after initial load on T-1 performs fast refresh, but on T-2 raised ORA-12034 and complete performs again.
What's wrong?

34MCA2K2, Google lover?
I confess perhaps I gave a little info.
View log was created before MV.
It was the first initial load.
No refresh failed.
No DDL.
No purge log.
Not warehouse.
There is no such behavior for MVs on another sites.
P.S. I ask help someone who knows what's wrong or who faced with it or can me follow by usefull link.
P.P.S. It's a pity that there is no button "Useless answer"

UCCX 8.0(2) SPAN/RSPAN based VOIP Monitoring

Hi Alll,
UCCX 8.0(2) High Availability (both servers are co-located in data center, where agents and supervisors are in building across the street over fibre)
SRND for UCCX 8 describes that it supports SPAN and/or RSPAN based voip monitoring, which is a requirement for my client as they have CAD Agents running on Citrix thin client and Supervisors on Thick client PCs.
However I am struggling to find a way to achieve this solution for my client with UCCX 8.x, UCCX 7 we would not have had this problem as you can configure 2nd NIC adaptor on UCCX server to be configured as VOIP Monitoring server port/IP under PostInstall and sniff all traffic for all Agent phone devices as configured under CDA.
Desktop Monitoring is not supported for thin client environment. Customer may eventually purchase QM/WFM, but for now we urgently require the essentials of agent monitoring on UCCX.
Please has anybody successfully had this configuration described above achieved? or have any ideas?
Thank you,
Yavuz

Have you been able to get a response to this post? I am running into the exact same issue with an upgrade to UCCx 8.0. SPAN on the 2nd NIC isn't allowed, and now the customer has lost functionality.
Thanks,
Ben

CCMS and PMI monitoring

Hi,
   I do have some doubts regarding CCMS and PMI monitoring..
   As of now we are plannig to configure CCMS.But i want to know about PMI.. when it comes to the picture in monitoring.
   How PMI is different from CCMS ? and which one is the better option to monitor
   Please clarify me...
Regards,
Sandeep

Hi,
Check the thread for details Re: Role of CCMS & PMI in Runtime Workbench?
Thanks!

CCMS in Component Monitoring

I haven't had to use this part of XI before and was just wondering what it is for. There's CCMS button when you run the runtime workbench and go into component monitoring.

Hi paul
refer the below links u will get everything about CCMS
http://help.sap.com/saphelp_nw2004s/helpdata/en/80/942f3ffed33d67e10000000a114084/frameset.htm
The Computing Center Management System (CCMS) performs tasks in the following areas:
1. System monitoring across the entire landscape
2. Determining and displaying statistical data
3. System management (for example, starting and stopping SAP systems, configuration, printing, background processing, resource management, and database administration)
The Alert Monitor is the central tool with which you can efficiently administer and monitor distributed SAP NetWeaver solutions or client/server systems
/people/aravindh.prasanna/blog/2005/12/23/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part--1 -- ccms 1
/people/aravindh.prasanna/blog/2005/12/24/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part-2 -- ccms 2
/people/aravindh.prasanna/blog/2006/02/20/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part-3 -- ccms -- 3
CCMS ALERTS
/people/sap.user72/blog/2005/11/24/xi-configuring-ccms-monitoring-for-xi-part-i
/people/sap.user72/blog/2005/12/05/xi-grmg-customizing-for-xi-ccms-heartbeat-monitoring-part-ii
/people/aravindh.prasanna/blog/2006/02/20/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part-3
http://help.sap.com/saphelp_nw04/helpdata/en/45/e32b64f87c6f74e10000000a1553f6/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/90/4e313f8815d036e10000000a114084/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/28/83493b6b82e908e10000000a11402f/frameset.htm
<b>Pls rewards if useful</b>

Problem about ccm based silence monitor(UCCE)

Similar Messages

Maybe you are looking for