Problem:Image capture with Nokia 6020

Hi,
i want an idea about the issue of "Image Capture" from midlet.
I tried my image capture application with SonyEricsson W550 it is working fine, and
I tried the same appliaction with[b] i-mate SP3(Windows CE mobile)and with Nokia 6020 ("Both are MIDp2.0 support "), the application not even loaded and the exception as javax.microedition.media.MediaException
one more thing the value of System.getProperty("video.snapshot.encodings"); become null.
Please tell me what are all the mobiles will support the ImageCapture from Midlet.
some exact (supporting)mobile models please...
Thankyou,

Hi,
The sun article says 3650 will support the MMApi options even its MIDP 1.0, then what about MIDP 2.0 devices(6020).
Somebody said even some devices may MIDP2.0, but it may not be the complete implementation device.
What is mean that .... like either supporting only audio ???

Similar Messages

IMac applications see my iPhone 5s but cannot display the photos. Last week I was using Image Capture with no problem.

I have an iMac 10.8.4 and an iPhone 5s. I recently downloaded 110 photos and 10 very short videos using Image Capture v.6.2. I plugged the phone into the iMac, all of the photos appeared in Image Capture, I selected all and sent them along to a folder on an external hd.
However, this week, attempting the same procedure, I get nothing. Image Capture sees my phone but does not display any photos, just a big blank window. Same response from iPhoto, Aperture, and Lightroom; they all recognize the phone but none of the photos appear. Insight would be appreciated! Thanks.

Hello WellShoot,
Thank you for the details of the issue you are experiencing with importing photos from your Camera Roll using Image Capture. You have taken some really good steps already to troubleshoot this issue. The article below has a few additional troubleshooting steps you can take:
iOS: Unable to import photos to computer
http://support.apple.com/kb/ts3195
Thank you for using Apple Support Communities.
Best,
Sheila M.

Issue with Image Capture with Lion

I have a Lion. My camera is a Nikon D700
I have Lightroom 3 and Lightroom 4
Recently downloaded Lightroom 4.1 connected my memory card reader to upload photos . Lightroom 3 opens and not Lightroom 4 to import the photos.
Checked Image capture application to change preferences - there is no preferences in image capture (Lion) My scanner is the only device that is shown.
Please advise how I change for image capture to open the correct Lightroom version.
thank you
Suer

Hi Frank
I have a Lexar card reader - being using it for years no problem -
I have again gone into image capture have notice the camera import process. I never had previously hat to worry about Image capture as my photo import ran smoothly with Lightroom 3 opening up automatically.
In Image capture there are options to where the photos need to be imported to. Only iPhoto option provided no Lightroom - Under "other" I typed in Lightroom 4.
However, the import process began without Lightroom 4 opening and the photos started to be imported in to the pictures folder ( this I do not want to happen) as I want Lightroom 4 to open .
However, there is no option to change from pictures folder - there is no option for Lightroom 4 , were it says "other: can I change to Lightroom 4?
As Lightroom option is not given , I chose "other" and inserted Lightroom 4 . When attaching my card reader , Lightroom 4 did not open to import only the pictures folder. Please confirm that I need to change to import to Lightroom 4 instead of the pictures folder. _
If this is so must I change the option from other to Lightroom 4 , even though I have already indicated " connecting this camera to....... see attachment.
Also I see there is an option to tick " delete after import" must this be checked?
See attachment
I have not attached the screen shot as in the reply window there is no option to do this

Using Image Capture with Epson NX420 in 10.5.8

I have not gotten around to updating my computer to Snow Leopard. My computer usually have two users with fast user switch. Usually the other user tend to have Photoshop open, so I can't use Photoshop(stupid licensing issue even though it is on th SAME computer!) in my account when I need to scan something. So I use Image Capture. I just bought new printer, Epson NX420 using Wifi.
I can't seem to get Image Capture to use the scanner wirelessly unless I use Epson's own Scan softare. I am pretty partial to the Image Capture cuz it's alot faster.
Anyway, my point is is there a way that I can get Image Capture to work with the NX420 on 10.5.8 without spending more money?

I was having this same problem, too. My MacBook Pro w/ Lion could no longer communicate with my Epson Stylus NX420, which seemed to happen randomly as the printer was working fine before.
I finally searched for the solution and found it! After downloading and installing the latest drivers on my Mac, it is now able to communicate with the printer and prints just fine.
Hope this helps.

Using Image Capture with HP Officejet Pro 8500 A909g

The printer/scanner shows up twice under the device list in Image Capture. Select either and I get an error message, "Scanner Session Fails to Open". The Officejet Pro works ok as a printer. It is connected to my Mac Desk Pro and to a MacBook Pro, both OS X 10.6.8, via an ethernet hub. This problem developed recently, I had no problem using the scanner in the past.

Hello srschoo,
Welcome to the HP Forums.
I see that you are having an issue when it comes to scanning.
I also see that you have attempted to run the HP Print and Scan Doctor.
One other step that we can try is to go through the steps that are listed in the following document. " A 'No Scan Options' or 'Scan settings are not set' Message Displays for HP All-in-One Printers When..."
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Problem sync iCal with Nokia N95

I´m trying to set up iSync to synchronize my iCal (MobileMe calendars) with Nokia N95 8 Gb.
Contacts is synchronizing fine but when I try to click the check-box to define which calendars I want to sync I get this message:
"Before you can synchronize your calendars, you need to open a calendar application that supports synchronization and create at least one writable calendar."
How can I create a writable calendar in iCal???
..gob...

Excellent!
Thanks Julian. I had no idea there were functions hidden behind that icon. So simple now you've shown me.
Thanks very much for your help.

Problem to synch with Nokia 6600

Hi all
I have 10.3.9 on my G5 and I syncronize my (old) Nokia 6600 (V 3.42.1) with isync, without any problem.
Now, I bot a second 6600 and there is the firmware V 5.27.0 installed. I am not able to synch with that phone.
Any idea if it would work when I update to tiger and the new isync, or do I run into other problems?
TIA
kk
G5 Mac OS X (10.3.9)

I have the same problem ,
tried using same application in 6600 and sony erricssion ,
works fine in sony but not in 6600 ,
i think there is more to fear..
the itemcommands also doesn't work
so only way is to add commands at form level ! it's strange

Image capturing with ni1409 and Jai CV-A1

I am using NI IMAQ 2.5 version.
I have done the procedures for interfacing Jai A1 camera with IMAQ 1409.
1. Download and install the camera control utility from the JAI Web site.
2. Launch the JAI A1 control utility, and click Start>>Programs>>CV-A1 Control Tool>>CV-A1 Control Tool.
3. Click the Shutter and Sync Signals button.
4. Set the Pixel Clock Out radio button to On to output the pixel clock.
Configuration Files
1. Copy the JAI CV-A1(1409).icd file into the \Data folder. Go to ftp://ftp.ni.com/support/imaq/camera_support/
camera_files/analog/jai/ to download this camera configuration file.
2. Launch Measurement & Automation Explorer (MAX).
3. Expand the Devices and Interfaces branch of the tree view.
4. Expand the IMAQ PCI/PXI-1409 branch of the tree view.
5. Right-click Channel 0: RS-170, and select Camera>>JAI>>JAI CV-A1.
6. Click Save.
When we are using the software for JAI A1, Camera control Tool interface(downloaded from JAI web site), the About window and Camera control window shows red color bar at the bottom and Communication window shows status in red color i.e. offline. I have tried to connect the camera control tool with JAI camera using the Communication window by clicking “auto” button. It is showing “no camera found”.
I have tried with both types of wire viz. BNC and NI. But the results are same.
The picture error.jpg shows the different windows those I have opened.
The window “Acquisition Error” arises when I have tried to grab the frame using NI Measurement & automation software. Rests are for Camera Control Tool software for CV-A1.

Hi again,
Please see your original thread, and use the "reply" button to create a response. Posting in multiple threads will make it more difficult to assist you in troubleshooting!
Thank you,
Robert

Image Capturing With LabView 6 (again)

how can I use my digital camera or web cam to get pictures from it?
all my cameras use Twain drivers so are there any support for Twain
in LabView?
My cameras are:
Mustek GSmart Mini II
Kodak DC-280
Michal

Michal,
You can use your cameras that have Twain drivers with LabVIEW. Although National Instruments does not directly have any tools for Twain drivers, you can make calls to the Twain API directly or you can use a toolkit which has done this for you. Graftek has a Twain toolkit for this type of application. Also, KB 16M8P2QH discusses this issue in more detail.
Regards,
JR A.
Application Engineer
National Instruments

Strange Problem capturing with Apple Intermediate Codec

We have the following problem:
We capture with a blackmagic decklink studio card (but I could reproduce the same problem using a MacBook Pro and the internal camera) with a MacPro and CS4. When capturing a live video feed (1280x720) with the apple intermediate codec (set to 29.97fps or to 59.94fps) everything seems to work just fine. But the resulting videoclips happen to be exactly ONE half of the total capture time. So if we capture in Premiere for about 1 our the clip is only 30 minutes long. If we capture for 10 sec., the clip will be 5 sec. long. It's not that the captured clips play with double the framerate. Half of the actual footage is missing.
Any suggestions?
By the way: we live in a PAL50Hz country, but our video signal that needs to be recorded comes in as a 60hz signal.

Hi,
Well I did some googling...and I would bet that the problem is the 50hz vs 60hz...
Unfortunately most if not all info I got that even BRUSHES on this subject with the sort of material you're dealing with is the opposite....where they are in 60cycle land with pal stuff....rather than in pal land dealing with 60hz ...
This is a lot of misc stuff but if you get a little bit of info from various posts and make some notes you might be able to get an idea how to solve the problem...
In particular I was looking at how frames are flagged and new frames are created later ...( toward very end of these posts - the last four or so )
Also noted some timecode reading that was "doubled"....so if your deck thought you had a specific length and then it read the timecode doubled, it would be your problem in a nutshell... have you checked the last frame you captured and compare that timecode to the overall length ??
anyway, here is a TON of stuff to breeze through...good luck...
THIS IS EDIUS RELATED..so keep in mind re: specific presets etc
Steve Sherrick
03-03-2008, 11:14 AM
Hi chaps,
Can I just confirm that the SDI/HDMI outputs are only live in build 14? I'm on 13 and going SDI - HDLINK - DELL24" gives me nothing. I'm in PAL land so have tried switching between 50hz and 59hz in camera.
So do I need build 14 or is it something else?
Cheers
Jeff Brown
#708
I'm in NTSC land but that same setup gives me picture just fine. Which Dell model is it? Is everything set up right from the camera side?
Jeff Brown
03-04-2008, 12:42 PM
Hi Steve,
I believe so. Set to Preview in th viewfinder settings, plugged in on preview mini sdi, cam set to 50hz..
Anything I'm missing?
Cheers
To counter this, the AJ-HD1400 offers two modes specifically for this called '25(SD)' and '25(HD)'. They output the 25fps signal with new timecode on a 50Hz carrier (only over SDI/Analogue the Firewire doesn't work in that mode).
It only works with 25fps material too, any other 'offspeed' rate has to be dealt with separately with the deck operating in 59/60 mode.
When operating in either of these 25 modes, the deck generates new 25fps timecode from the tape (although our tests have indicated that it is frame accurate of multiple playback passes).
Basically, Varicam, while a very nice idea, has only ever been properly designed to work in a 60Hz environment. It is pretty much a nightmare in 50Hz environments.
I think I may have found the cause of the problem.
For some reason when I started my project it had a Device Control profile set to 720p50 (rather than the 1080i50 that the deck is operating in).
What this seems to have done is double the frame number on any clip it encountered. So if I took a clip with in marked at 01:02:40:22 and dropped it in the Log and Capture tool the In Point that FCP decided to look for was 01:02:40:44 (which isn't going to exist on a 25fps timecode obviously).
Since you are using Pal
Go :
Generic OHCI HD 50hz -> 960x720 25p over 60p
Because if I am right you can't do Pal over 60hz but you can do PAL over 60P at 50hz.
( but I could be wrong)
But the other problem is that you are using an ntsc profile to capture pal recorded footage.
50 hz 960x720 over 60P yields a frame rate of 25 progressive
60 hz 960x720 59.94p yields a frame rate of 59.94 progressive which is far from your original footage . Mostly used for countries using natively ntsc
Neither myself, nor Ricksta (I don't think) are using NTSC-rate profiles.
The Preset setting I've been testing with is:
Generic OHCI HD 50Hz 960x720 25p over 60p
Indeed, I've just tried what Rick mentioned, and with the deck in 59.94Hz operating frequency, I can capture with all three 720p 59/60 input settings. This is technically wrong however, as the tape has been recorded at 60Hz. But like I said before, until Rick hears from the big geeks at Panasonic about this, I don't know what the real outcome of that difference in frequency is.
I've also tried a 50p over 60p project setting (as 720p50 is what I will be editing with in Avid) - but, predictably, this works but gives me double-speed footage. Which, while amusing, isn't a lot of help for me
A large part of the problem I'm facing here is to do with the Varicam format. It will record any framerate from 1-60fps. It has to operate and a system-frequency of 59.94Hz or 60Hz. That is what Rick and I are referring to. The limitation I face is that the Varicam format is not widely supported for PAL-based rates (25/50) as it requires communication with a deck operating in an NTSC-based system frequency (either 60Hz or 59.94Hz). This difference (between project/timeline framerates, and deck operating frequencies) is enough to ensure that IEEE1394/Firewire/OHCI capture is not possible in these modes in Final Cut Pro, Avid (any version) or any other NLE I have found.
We realise that the framerate and frequency we're working in has to be 50-based, and we're not making any mistakes in that respect.
So far Edius is the only NLE on the market, that I have been able to find, that supports Firewire capture from 60Hz DVCPro HD material in a 50Hz based framerate.
When you have captured the file in that project select a clip in the bin press alt+enter go to video info and tell me what the framerate is .
In a 50p over 60p project, when I capture footage shot 25p over 60 with the 'Constant Rate' capture profile I get a clip in the bin that is 50fps, but that plays at doubletime - which is what I'd expect.
I can change the framerate in the properties to 50fps, and it plays at the correct rate, but I'm not happy with the way to refactors the timing in that mode. It seems to create interpolated frames to fill the gaps, which provide an unusual appearance that I don't really like.
At present if I capture into 25p over 60p project, then import the resulting 25p footage into Avid, Avid doubles up the frames to produce 50fps material.
Some clarification here. The Varicam does indeed record at a constant 60fps. If the frame rate is set to 25fps for example it simply flags the active frames. This flag is carried in the vertical interval data. The reason for this system, is as suggested, it is very difficult to vary the speed of tape in a helical scan recording system. With the advent of solid state recording that Panasonic introduced in the AG-HVX200 it is now possible of course to only record the active (native) frames and this would be called 25pn for example.
Originally with the Varicam you used to use a device called a Frame Rate Converter. This box contained a hard drive with HD-SDI I/O. It would recognize the active "flagged" frames in the incoming signal and buffer them through the hard drive and then play them out at the correct frame rate.
More recently NLE's such as Avid, FCP and Edius have incorporated this flagged frame recognition and perform the extraction automatically. Thus when I tested a 25fps Varicam ingest on a 25 Frame timeline I am getting realtime playback. If I had recorded at 50fps and I placed that on a 25 frame timeline I would have very smooth half speed. Also the newer DVCPRO HD decks such as the AJ-HD1700 and AJ-HD1400 have the ability to decode "on-speed" frame rates such as 30fps, 25fps and 24fps.
The issue that Dylan is facing is that the NLE's will not accept a firewire input at 60Hz, they only accept it at 59.94, this is a .001 frequency difference and should be negligible. The other alternative is to ingest via HD-SDI via a Black Magic or AJA Kona card etc. These boards also support the variable frame rate function.
I hope that this helps clear things up a little.
Rick Haywood
Manager Broadcast & Display Systems
Panasonic New Zealand Ltd.
Further to what Rick is saying... The issues with most NLEs for PAL users is the disparity between the 59.94/60Hz operating frequency of the deck and the 50Hz based framerates the applications are working with in PAL framerates.
As for the constant 60fps - it is indeed recording 60 images per second to a tape, but as I said before, only a certain number are unique - only the flagged frames. In 25fps, the camera samples the sensor 25 times a second and records that frame to tape. Essentially you get frame 1 recorded for 2 frames, frame 2 recorded for the next three frames, frame 3 recorded for 2 frames, etc... The first frame with each unique image is 'flagged'. To rebuild the recorded framerate, only the flagged images are captured.
The big bonus of Edius for me here is that it can capture the PAL framerates from the 59.94Hz deck over Firewire directly. Something that Avid and FCP are unable to do.

Image capture bug

I'm using Image Capture with a Canon S400. Image Capture was set to download all photos automatically and delete after.
I've never had much luck with this approach. Unfortunately I'm a slow learner and only now have vowed never to use the app again. Basically, it downloads the first couple photos okay and then speeds through the rest of the photos at light speed (clearly, something has went wrong.) Indeed, the rest of the photos cannot be read by any application- they are invalid JPEG files even though they are about the right size. And they've been removed from the card and are gone forever. I'm using the factory USB cable from the camera the the keyboard USB port. Hardware is either a MacBook or intel iMac. Both have the same problem.
What gives? One might be inclined to point to the camera or CF card but in fact both are fine. I can use a CF card reader fine with my iMac, and everything also works great with my Windows XP box.
At the absolute least, Image Capture should be updated to NOT delete photos from the camera unless the resulting JPEG passes some type of minimal validity check. OS X is instantly aware of the fact that the image files are corrupted (no thumbnail can be generated) so it shouldn't be that difficult.
Sigh. I'm really starting to long for the stability of my iBook. I defended Apple as long as I could but with the MacBook in for repairs right now and various stability issues running OS X on the Intel platform, I realize now that there really are some serious issues right now.

I'm having a similar bug on an eMac with the same camera (plus an Olympus E-300). Yes, dragging the jpegs off the card works, but you lose the thumbnails that Image Capture creates. I've researched previous questions here, and believe I've found all the preference files (that I have trashed several times over). No luck - I keep having this problem.
I really don't want to give up on Image Capture, since it retrieves camera information, too. But this is really an irritating bug!
Any suggestions..?

Where are temporary files created for "image capture"?

Hi all
I have been using image capture with no problem whatsoever, until recently. I was scanning a big file and while it was saving it or something I closed the lid of the computer and interrupted the scan. Now the scanner can do a preview but is no longer able to "scan" the file that i see perfectly through preview. I think that the problem is that there is a corrupt temporary file somewhere that needs to be manually deleted. If you know where such files are stored or if you have a better idea, please let me know.

You may be on to the correct solution. I've seen this problem with a big printing job that a user had to cancel and then had to "go in" and delete the print job before they could print again. On the Mac, there is something called CUPS (something Unix Printing System) and it has a role in printing and I believe faxing. It "might" play a role in scanning through Image Capture but I'm not sure. Anyway give it a look and see if there is an incomplete scan job in there that you can delete.
Note: this looks like a website URL but it leads to CUPS on your Mac.
http://127.0.0.1:631/jobs/
This may not be applicable to scanners but it's worth a look.
Regards,
Steve M.

Image Capture scans to Pictures folder

I'm using CanoScan LiDE 200, with Image Capture, with scans going to iPhoto.
But the scans are also saved in Pictures folder.
How to stop the scans go to Pictures folder ?
Thanks!

correction to my post above:
.....the location to which IC scanning is iPhoto. That's no problem, it's checkmarked.
What happens is that both, the 'Pictures' folder small window opens when scanning, and you can see how a tiny thumbnail is being added there, and iPhoto opens.
It's not the "Pictures" folder that opens(in addition to iPhoto, which is checkmarked), but a small window that says: "Scan Results".
On the bottom a button "clear". Pressing "clear", removes the thumbnails from "scan results", but they're still in "Pictures" folder.

How do i get mavericks image capture to see a networked scanner?

we have a networked scanner, an imac & a mac mini. prior to upgrading the imac to mavericks from snow leopard [mini is still on snow leopard], neither had any issues using image capture with the scanner. since upgrading the imac to maverics, when i start up image capture, it does not see the scanner as a shared device, even though it is seen in the system pref/printer-scanner app. i have to reboot the imac to get the image capture to see the scanner. i am in the middle of scanning hundreds, if not a thousand, of old photos & this is a PITA.

Assuming the iTunes and AppleTV are set for Home Sharing, navigate to the iTunes library listing under Computers on AppleTV - there should be a new Rentals row along with Music, TV Shows etc.
The movie must download fully to iTunes before becoming available. Also check it's still in iTunes and hasn't expired due to playing it inadvertently too soon.
AC

Image Capture & ICC profiles

Is it possible to use Image Capture with my scanner and have it embed something other than the sRGB colour profile when scanning colour photographs? I'd like it to embed AdobeRGB instead. In most other respects I prefer it for scanning photos to Epson Scan and VueScan.

Hi G-Man,
It's probably something in the Preferences folder; Users/herusername/Library/Preferences. Start by removing com.apple.ImageCaptureApp.plist and trying again. If that doesn't do it drag the entire Preference folder to the desktop, log out and back in. Launch it again and if it works you can either reset preferences for all System Preferences and apps or drag the preferences files a group at a time back to the new Preference folder in Library and test Image Capture each time. That way you can narrow it down to the one offending preference file.
John

Problem:Image capture with Nokia 6020

Similar Messages

Maybe you are looking for