Problem setting up 5Ghz security on WRT610Nv2 2.00.00.B05

Was able to set up my WRT610v2 to use WEP on the 2.4 Ghz side with the same key as my old router and my network is running fine. When I go to set up the 5Ghz side however I'm seeing a really odd problem even the Cisco tech rep I chatted with could not figure out. When I try to select the Security Mode in the 5Ghz Wireless Security section the dropdown menu only shows 3 options: Disable, WPA2-Personal and WPA2-Enterprise. The manual says that I have to use WEP throughout but that isn't listed as an option. Any idea why this should be happening? I checked the firmware version and I'm running 2.00.00.B05; the Cisco rep is trying to talk me into flashing 2.00.00.05 but could not tell me whether the "B" in the name of the version I'm running has any significance. My version does show a date on the version that precedes the copy on the website by 12 days but I can't see any reason to believe that's significant.
I will switch to WPA2 at some point when I have time to amend the other devices in the network; that just doesn't happen to be now.

Thanks for the feedback; last night after I posted this I discovered something that perhaps everyone else knows and I just missed in the documentation. Since all the devices I want to use the 5Ghz band are 802.11n I decided to set that band's Network Mode to Wireless-N only. Apparently when you do this it limits your security selections (for reasons I do not know) to WPA2 or disabled. When I went back and changed Network Mode to Mixed the security options available expanded to include WEP. I now have part of my network running WEP on that SSID, part running on the SSID for the 2.4 Ghz band.
Does anyone know if there is a difference between the firmware version 2.00.00.B05 the router shipped with and the 2.00.00.05 version available for download? The tech I spoke to last night at first didn't even seem to realize I was seeing the extra character "B" in the version and when I pointed it out the second or third time had no explanation for its being there. The downloadable version does have a date that is 12 days later than the shipped version but I don't see much significance in that by itself. If there is a real reason to reflash I'd be happy to do it but would rather not without cause.
If WEP can be used in mixed mode is there some reason it cannot be in Wireless-N only mode? Sometimes the difference between a "feature" and a bug can be obscure...

Similar Messages

PROBLEMS SETTING UP REPORTS SECURITY FEATURE

1. Trying to follow instructions to set up the Reports Security Feature.
2. Successfully run the script rwwwvins.sql
3.Hitting following Error
" Missing string(reports_security_desc) language(us) domain (wwc)sub_domain
(sec)
The portlets have similar names.
The pageORACLE_REPORTS_SECURITY has a display name of :
Missingstring(reports_security_desc) language(us) domain (wwc) sub_domain
(sec)"
4. Followed note 132625.1 with no joy. Same error.
Any help ?
null

do you mean to say that you cannot enter any passphrase on the router web ui or on the wireless computer itself ??
if its on the router , then upgrade / reflash the router's firmware...

Problems setting integrated security to false on sub reports

We can set the integrated security to false on the main report, but for some reason it is not working on sub reports. Is there an issue with this? Possibly a patch we need to apply?
I downloaded the SP0 patch for CR2008 and attempted to apply it, but it said something about doing this from control panel. I normally would expect a DOC or TXT file with some instructions on patching, but I just keep getting redirected to the business objects web site generic page when I try to get more information.

Please have a look at this White Paper. It should be quite helpful with this issue:
https://websmp109.sap-ag.de/~form/handler?_APP=01100107900000000342&_EVENT=REDIR&_NNUM=1219774&_NLANG=E
Ludek

Problems Setting Up Developer Users

I am having a problem setting up developer users and I am trying to determine if I am missing a step or if there is a configuration problem on my staging and production systems.
What I want to do should be very simple. I want to create a user that can create an application and see the information under the "Application" tab in the Navigator.
I have created the user using the following steps on 3.0.9.82 for Unix:
1. Create the user
2. Make the user a full administrator (rather than end user)
3. Make the user a member of the portal_developers group
4. Make the user's default group the portal_developers group
However, when I do this the user does not see the information under the
"Application" tab. The only way I can get the user to see the info under the
"Application" tab is to make him a member of the Portal_administrators
and/or DBA group. Both my staging and production boxes have the same result.
Does anyone have any thoughts or suggestions on what might be happening?

Thank you- I have read through that thread and can see some resonance with my issue.
My AOL emails work VERY fast with BB, in fact almost simultaneously received on PC & Torch " ping ping!"
This issue only raised its ugly head when I had 2 Torches replaced by my insurers.
Whilst the claim was in process I used a new Curve, loaded from backup on PC to keep emails going and of course phone & web facilities. ( I use the BB to power internet via bluetooth to my PC / laptop when living on a remote island with no phone lines or power supplies) All was fine. Swapping email accounts took a few minutes with the usual password confirmations for each AOL screenname etc.
Then the new Torches came back from insurers, and I tried to swap devices. Phoning & texting is fine. Al data and contacts swap over fine.
SETUP email accounts.............stymied every time. It says repeatedly that my user name/password is invalid etc etc etc
Have tried security wipes. Have tried setting up new BB ID & passwords on PC website. All is OK until I try to setup emails on the Torches. This has used up ridiculous amounts of time- all wasted.
I love the BB phones and the fast email push......in fact I recently bought a new Sony Xperia Z1 but sent it back because of wifi coverage meant no emails on that superb phone for lots of the time.
Good old BB I said..........I always get emails wherever I am. ( Rural Scotland has very patchy radio & wifi coverage)
Was about to purchase new Z10s just to get a bigger screen, but now I am averse to buying ANY BB phone again because this present mess means I may never get emails set up again. How nuts is that?
Many thanks for all help & suggestions..........boy do I need them!!
Kind wishes from West of Scotland
Fair winds and kind landfalls

Problems Setting up my wireless network with an Xb...

Hi, I have had some problems setting up my wireless networking.
I have everything switched on and am able to go online with the laptop and the Xbox with no problems but when I try to share media with the xbox I have problems.
I have opened the ports specified in the setup from xbox on windows firewall and have no problem connection Via Ethernet cable but when using wireless the xbox cannot detect the laptop.
I have checked the network map and both xbox and laptop are connected and have enabled sharing and am running sharing software.
Below is the network map.
I have also been having problems with BT software, the free virus protection will not install, The desktop help will not launch although it shows up on task manager and the installation disk does not launch correctly it doesn't get past the loading screen.
I have had a printer on the wireless network and had no problems printing.
If anyone knows how to resolve this please help.

I have this same Motorola modem and I just verified that my 802.11n AirPort Express Base Station (AXn) can get Internet access with this modem without any issues.
When changing ISPs (or networking equipment) it's always a good idea to start from "scratch" in configuring your equipment.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Power-up the modem; wait at least 10-15 minutes.
Power-up the base station; wait at least 5-10 minutes.
Power-up your computer(s).
In this basic configuration, computers connected to the base station, either by wire or wireless (as appropriate for the base station type), should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options.

Problems Setting up a Direct Debit

has anyone experienced any problems setting up a direct debit ??
I've been a BT customer for approximately 20 years and have had the same account number. I've moved house a few times and retained the same account. My last house move wasn't so successful as after moving in and having broadband re set up again... I received a letter in the post saying I had requested a "termination" and a parcel was included to send my router back etc... plus... I'd be charged £100+ for the disconnection...
Anyway I got on the phone to BT and the advisor appologised for the mix up... and suggested I cancel my direct debit with the bank to make sure the disconnection fee wasn't taken from my account.....
Ever since then... I have not being able to set up a direct debit online or by speaking with several BT helpdesk staff. I email BT asking for an explaination - NOTHING. BT helpdesk staff assure me that the direct debit will work this time and will contact me if there is a problem... again NOTHING. I even tried writing a letter to the head of customer services... I think the name Warren Buckley rings a bell.. Someone did email me back suggesting I use the online facility.... REALLY!! Do BT not have a fault tracking database of customer issues... so they can see I've already tried to set up the direct debit online...
Anyway ..... I've just noticed this forum now... so this is my latest attempt to see if anyone senior enough at BT will be embarrassed and try and sort out my account so I can start paying my bill using Direct Debit again... I'm pretty sure all that needs to happen is to be given a new account number or an account alias that can be sent to my bank. Otherwise... I'll just carry on waiting to receive the automated message from BT saying I haven't paid and then go and pay online... But I am worried one of these automated messages will arrive the day I go on a 2 week holiday and I find myself cut off when I get home... giving me more pain....
PLEASE HELP BT ;o)
regards
DaveB

I have asked a moderator to provide assistance, they will post an invite on this thread.
They are the only BT employees on this forum, and are a UK based team of people, who take personal ownership of your problem.
Once you get a reply, if you click on their name, you will see a screen like this. Click on the link as shown below.
Please do not send them a personal message, as they may not be on duty for a long time, and your message will not be tracked properly.
For your own security, do not post any personal details, on this forum. That includes any tracking number you are give.
They will respond either by phone or e-mail within 5-6 working days.
Please use the tracked e-mail, to reply, not via the forum. Thanks
This is the form you should see when you click on the link. If you do not see this form, then you have selected the wrong link.
When you submit the form, you will receive an enquiry number, so please keep a note of it
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Problems setting up a Domain - javax.management.InstanceNotFoundException

I am having problems setting up a Domain. The following steps summarize
what I have done.
1. Created FooDomain in d:/bea/wlserver6.0/config and created
appropriate config.xml, startup scripts, security, etc... (FooDomain
boots ok)
2. Moved console.war to bea/wlserver6.0/config/FooDomain/applications
3. Connected to FooDomain via console (works ok).
4. Defined machine FooMachine (happens to be localhost)
5. Defined new server FooServer (in addition to default myserver) and
assigned it to FooMachine.
6. Created a new directory d:/managedServers/FooServer (note - outside
installation directory)
7. Created directories d:/managedServers/FooServer/logs &
d:/managedServers/FooServer/applications
8. Copied sample startManagedServer.cmd from mydomain to
d:/managedServers/FooServer & modified appropriately.
9. Ran startManagedServer.cmd (Note: I was able to connect to the
Administration Server ok)
The problems are as follows. (From the console - pointing to the
Administration Server for the FooDomain)
1. I am unable to configure a DefaultWebApp_FooServer to be located at
d:/managedServers/FooServer/applications. I get the following exeption:
javax.management.InstanceNotFoundException:
FooDomain:Name=DefaultWebApp_FooServer,Type=WebAppComponent.
2. I get a similar error when trying to set FooServer log locations to
d:/managedServers/FooServer/logs
Any ideas as to why? This then begs the question, what if FooServer was
on a different physical server altogether. How would I define the
location of the DefaultWebApp and logs.
Thanks
jay ()

If you want your application work, think my way. At least, all my teammates have used this method to build their development environment. If you are more interested to debug for Weblogic, contact your support representative. The tools from Administration console look very nice, but not function as you want (e.g., the tool to convert version 5.1 application to version 6, even monitor tools). Administration console is very nice to be used to configue the parameters for a domain, but not so trustful and not for application setup in my own experience and that is why I suggest you use mydomain and DefaultWebApp_MyServer as templates. By the way, I did modify config.xml manually to change the default web application entry, etc, to what I want.
Jay Zammit <[email protected]> wrote:
I did not modify config.xml manually. In fact, I am able to boot both the Administration Server & Managed Server. The problem happens when using the Administration console to assign my logs and Default Applications directory to the d:/managedServers/FooServer/logs, and d:/managedServers/FooServer/applications/DefaultWebApp_FooServer directories. Try it yourself. Go to the Configurer WebApp option and type in a fully qualified directory such as d:/managedServers/FooServer/applications/DefaultWebApp_FooServer
and see if it works on your system.
thanks
jay ()
Xiang Rao wrote:
One suggestion. Use the default domain mydomain as a template. Just make a copy of "mydomain" in folder config and rename the copy to whatever you like. Use some help tools to search all files (non-binary files) in new domain for key word "mydomain" and replace these words with your new domain name. To build an application, just rename the DefaultWebApp_MyServer to what you like and search "DefaultWebApp_MyServer" in all files (non-binary files) in your new domain and replace these words with yournew application name. Note you need to modify the scripts accordingly. Then you can run "startWeblogic" in your new domain directory to start your new domain. Other parameters should be configured by Administration console. If you manually modify configuration files, you could expect some bad news without reason.
Jay Zammit <[email protected]> wrote:
I am having problems setting up a Domain. The following steps summarize
what I have done.
1. Created FooDomain in d:/bea/wlserver6.0/config and created
appropriate config.xml, startup scripts, security, etc... (FooDomain
boots ok)
2. Moved console.war to bea/wlserver6.0/config/FooDomain/applications
3. Connected to FooDomain via console (works ok).
4. Defined machine FooMachine (happens to be localhost)
5. Defined new server FooServer (in addition to default myserver) and
assigned it to FooMachine.
6. Created a new directory d:/managedServers/FooServer (note - outside
installation directory)
7. Created directories d:/managedServers/FooServer/logs &
d:/managedServers/FooServer/applications
8. Copied sample startManagedServer.cmd from mydomain to
d:/managedServers/FooServer & modified appropriately.
9. Ran startManagedServer.cmd (Note: I was able to connect to the
Administration Server ok)
The problems are as follows. (From the console - pointing to the
Administration Server for the FooDomain)
1. I am unable to configure a DefaultWebApp_FooServer to be located at
d:/managedServers/FooServer/applications. I get the following exeption:
javax.management.InstanceNotFoundException:
FooDomain:Name=DefaultWebApp_FooServer,Type=WebAppComponent.
2. I get a similar error when trying to set FooServer log locations to
d:/managedServers/FooServer/logs
Any ideas as to why? This then begs the question, what if FooServer was
on a different physical server altogether. How would I define the
location of the DefaultWebApp and logs.
Thanks
jay ()

Problems setting up WRT54G2 router

I'm having problems setting up my Linksys WRT54G2 router. I want my mac laptop (iBook G3 running OSX) to use a wireless connection, and the home computer (running Windows XP) to stay connected to the modem.
I originally tried to set up the router by connecting it via ethernet to my laptop (and by ethernet to the modem), and went into the 192.168.1.1 address to configure it. The internet works fine on my laptop when connected to the wireless by ethernet but it can't connect wirelessly (it has an original airport card fitted, at first I thought I might need to upgrade the firmware but I ran a software update and one didn't come up). I then realised that I would need to MAC clone from the PC, that is connected to the modem? I tried to do this today, but I couldn't access the 192.168.1.1 address from the PC. I have tried resetting the router, and disabling the firewall but still can't access it. This PC also has anti-virus software running too - could this be the problem, or am I setting it up wrong? Thanks.

If you are trying to Setup your Router with the setup disk, Then you can exit from the setup and configure your Router manually. Before you configure your router, you need to Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your router, wait for 60 seconds and re-connect the power cable.....
You need to connect your Modem to Linksys Router on Internet Port and your Computer to Linksys Router on Port No.1.
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link
Here are the Wireless Settings which you can set on your router, once done you can try connecting your MAC computer to your Wireless network and check if you are Online from MAC computer.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
-Here select manual configuration...Wireless Network mode should be mixed...
-Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Wide-40MHz and change the Wide channel to 9 and Standard Channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on save settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select AES...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2307 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

PROBLEMS SETTING UP EMAILS AS DEVICE REFUSES TO RECOGNISE PASSWORD AND/OR USER NAME

PROBLEMS SETTING UP EMAILS AS DEVICE REFUSES TO RECOGNISE PASSWORD AND/OR USER NAME
My 9800 ( I have 2 - one spare ) is driving me nuts- will not let me set up email accounts from my other Curve model.
Repeatedly told that either user name or details are wrong, yet they are RIGHT on website.
Exasperated
Help please??
Fair winds and kind landfalls

Thank you- I have read through that thread and can see some resonance with my issue.
My AOL emails work VERY fast with BB, in fact almost simultaneously received on PC & Torch " ping ping!"
This issue only raised its ugly head when I had 2 Torches replaced by my insurers.
Whilst the claim was in process I used a new Curve, loaded from backup on PC to keep emails going and of course phone & web facilities. ( I use the BB to power internet via bluetooth to my PC / laptop when living on a remote island with no phone lines or power supplies) All was fine. Swapping email accounts took a few minutes with the usual password confirmations for each AOL screenname etc.
Then the new Torches came back from insurers, and I tried to swap devices. Phoning & texting is fine. Al data and contacts swap over fine.
SETUP email accounts.............stymied every time. It says repeatedly that my user name/password is invalid etc etc etc
Have tried security wipes. Have tried setting up new BB ID & passwords on PC website. All is OK until I try to setup emails on the Torches. This has used up ridiculous amounts of time- all wasted.
I love the BB phones and the fast email push......in fact I recently bought a new Sony Xperia Z1 but sent it back because of wifi coverage meant no emails on that superb phone for lots of the time.
Good old BB I said..........I always get emails wherever I am. ( Rural Scotland has very patchy radio & wifi coverage)
Was about to purchase new Z10s just to get a bigger screen, but now I am averse to buying ANY BB phone again because this present mess means I may never get emails set up again. How nuts is that?
Many thanks for all help & suggestions..........boy do I need them!!
Kind wishes from West of Scotland
Fair winds and kind landfalls

Im having problem setting up my Hotmail account, it used to work fine until few days ago. It says ive entered an incorrect username or password which i can sign in fine with them details if i use laptop or safari through the phone, Please help..

Im having problem setting up my Hotmail account, it used to work fine until few days ago. It says ive entered an incorrect username or password which i can sign in fine with them details if i use laptop or safari through the phone, Please help..

I Sugges you to log into your hotmail acc and go to security and password change bit, then you will see two-step verification.. turn that off and you will be able to set it up on your iPhone/iPad or even Mac.
Give your phone a restart before trying to set it up. Thanks

Setting field level security

I have created a form in LiveCycle in which two fields (Header and an Image block) need to be editable by one user type (e.g. power user), but should not be changeable by the end users. They will only be able to fill in other fields in the form. So far I have only been able to set form level security. Is there a way to apply security to just these two fields, perhaps requiring a password, so that the power user can update these two fields as needed?
Thanks for any ideas you might have!

Hi Diego,
Thanks for responding. We aren't using the LC PM module, so that takes one suggestion out of the running.
We tried some Javascript we found on the Acrobat forum (see below for what we used) - using it as an action with a bookmark, but it didn't work. The guy who wrote the script on that forum looked at our file and thought that the problem was likely because the form was developed in LiveCycle. We are not Java experts (or even close!), so we have no clue where to start. And unfortunately if we cannot find a solution for this dilemma, we will have to decline a project from a client.
So again, any thoughts or suggestions on where to go from here are greatly appreciated!
(function () {
    // Get one of the fields in the group
    var f = getField("private.name");
    // Determine new readonly state, which
    // is the opposite of the current state
    var readonly = !f.readonly;
    var readonly_desc = readonly ? "deactivate" : "activate";
    // Ask user for password
    var resp = app.response({
        cQuestion: "To " + readonly_desc + " the fields, enter the password:",
        cTitle: "Enter password",
        bPassword: true,
        cLabel: "Password"
    switch (resp) {
    case "your_password": // Your password goes here
        getField("private").readonly = readonly;
        app.alert("The fields are now " + readonly_desc + "d.", 3);
        break;
    case null : // User pressed Cancel button
        break;
    default : // Incorrect password
        app.alert("Incorrect password.", 1);
        break;
In this example, the fields that are controlled by this all have a field name prefix of "private", for example "private.name", "private.address", etc. This makes it easier to control the fields as a group, as I do in the line of code that begins: getField("private").readonly If you don't use such a field naming convention, you'd have to have a separate such line for each field in the group.
Replace "your_password" above with one of your own. The first and last lines are not necessary, but do prevent the needless creation of document-global variables, which is a good thing.

Urgent Problems with Web Start Security

Has anyone used Java Web Start to load application? I have given all-permissions to the application when loaded and also give the AllPermission in Policy.setPolicy() inside the code. I encountered the following problems right now.
(1) In the application, I want to connect another server (different from the web server where I load the application), and get the following error (looks like that I cannot ping other server):
com.esri.mo.client.io.UnableToPingEsrimapException: Unable to ping ESRIMAP
(2) I create local directory, connect to database, use the return results to create some corresponding local files and load the local files in the Swing component, but it just cannot load. Here is the error message:
java.security.AccessControlException: access denied (java.io.FilePermission C:\Documents and Settings\ABC\Desktop\.\shpdir read)
I believe all these problems are resulted from security. But I have set the permission and policy already, so any solutions are highly appreciated!
Best Regards
David

Has anyone used Java Web Start to load application? I
have given all-permissions to the application when
loaded and also give the AllPermission in
Policy.setPolicy() inside the code. I encountered the
following problems right now.
(1) In the application, I want to connect another
server (different from the web server where I load the
application), and get the following error (looks like
that I cannot ping other server):
com.esri.mo.client.io.UnableToPingEsrimapException:
Unable to ping ESRIMAP
(2) I create local directory, connect to database, use
the return results to create some corresponding local
files and load the local files in the Swing component,
but it just cannot load. Here is the error message:
java.security.AccessControlException: access denied
(java.io.FilePermission C:\Documents and
Settings\ABC\Desktop\.\shpdir read)
I believe all these problems are resulted from
security. But I have set the permission and policy
already, so any solutions are highly appreciated!
Best Regards
DavidHello David,
If you want to use local files(R&W) then you have to set the following lines the .jnlp file like this:
<security>
<all-permissions/>
</security>Now if you assign all permission then you have to make jar file signed.(you can use jarsigner tools provided with the jdk_1.4.* to make the jar file signed).
If the jar file is signed then you have unrestricted access to the client side.
best of luck.

TS4123 I have problem with iTunes story (secure link to itunes store failed). I make In the "Command Prompt" screen, type in netsh winsock reset the itune story is solve but after i close itunes the problem is back

I have problem with iTunes story (secure link to itunes store failed). I make In the "Command Prompt" screen, type in netsh winsock reset the itune story is solve but after i close itunes the problem is back

The results show that you have a proxy server set and this can often cause problems with iTunes.
The proxy setting can be accessed in Internet options>>Connections>>LAN Settings.
Try un-checking the proxy server check box.
It might also be a good idea to run a malware check if you didn't know you had the proxy server set.
You can download a free version of an excellent scanner- Malwarebytes here:
http://www.malwarebytes.org/

Unable to connect to Linksys E3000 when set to 5GHz "N" only Network mode

I've not been able to connect to my to Linksys E3000 when set to 5GHz "N" only Network mode. Connections to the 5GHz can only be done in mixed mode. I do not need to have A-Mode enabled, so I do not wish to use mixed.
Tested with a variety of adaptors, most recently my Intel® Centrino® Ultimate-N 6300 .

Thank you for your response.
I have Win 7 Ultimate.
Wireless NIC: Intel® Centrino® Ultimate-N 6300
Latest Driver: 14.0.1.2
I took your suggestions, and verified the firmware is current.
Channel Width: 40
Channel: 161
Also, I have turned security off for testing.
If Network Mode = N Only, I see and can 'connect', but then get the error below:
If "Network Mode:" = Mixed, there is a connection, but Status-> Local->DHCP Clients verifies it as "A":
w520 Wireless-A 172.222.1.33 00:xx:x7:AE:xx::0C 23:59:45
I have the latest firmware
Firmware Version: 1.0.04 build 6 Dec 6, 2010
Firmware Verification: 1ad912eecfd4c2226624cc8ff9b43820
The error from Windows is non-specific:

Problems setting up username & password for SQL

Due to the outstanding advice I recieved from this excellent forum, I have managed to overcome my first problem with declaring a new Class.
This leads me to request help with my next biggest problem:
Setting up a user GUI that takes a "username" & "password" that will be used to access a password protected database.
I am a simple bloke, with simple thought processes, so please, go easy on me...
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.sql.*;
public class DBQuery1 {
     String username = "" , password = "";
     public static void main(String[] arguments) {
          PassDB UPass = new PassDB();
          String data = "jdbc:odbc:JavaTestDataBase";
          try {
               Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
               Connection conn = DriverManager.getConnection(data, "" + username, "" + password);
               Statement st = conn.createStatement();
               ResultSet rec = st.executeQuery(
                    "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                    + "WHERE (Title='Mr') ORDER BY ContactID");
          /*     ResultSet rec2 = st.executeQuery(
                    "SELECT Subject, ContactID FROM Calls "
                    + "WHERE (Subject Is Not Null) ORDER BY ContactID");
          System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
          while(rec.next()) {
               System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
          st.close();
          catch (SQLException s) {
               System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
          catch (Exception e) {
               System.out.println("Error: " + e.toString() + e.getMessage());
class PassDB extends javax.swing.JFrame implements ActionListener {
     String username = "", password = "";
     JTextField uname = new JTextField(10);
     JTextField pword = new JTextField(10);
     // JPasswordField pword = new JTextField(10);
     PassDB() {
          super("duBe's database logon");
          setSize(220, 160);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          JPanel pane = new JPanel();
          JLabel unameLabel = new JLabel ("Username: ");
          JLabel pwordLabel = new JLabel ("Password: ");
          JButton submit = new JButton("OK");
          submit.addActionListener(this);
          pane.add(unameLabel);
          pane.add(uname);
          pane.add(pwordLabel);
          pane.add(pword);
          pane.add(submit);
          setContentPane(pane);
          setVisible(true);
     public void actionPerformed(ActionEvent evt) {
          PassDB clicked = (PassDB)evt.getSource();
          username = uname.getText();
          password = pword.getText();
This code generates two errors, stating:
C:\Java_progs>javac DBQuery1.java
DBQuery1.java:14: non-static variable username cannot be referenced from a static context
Connection conn = DriverManager.getConnection(data, "" +
username, "" + password);
^
DBQuery1.java:14: non-static variable password cannot be referenced from a static context
Connection conn = DriverManager.getConnection(data, "" +
username, "" + password);
                ^
2 errors*****************************
The code works when I remove the reference to the variables "username" & "password" in Connection "conn" call & replace them with the actual username & password, but this is not exactly what I was after. I was hoping to make the program responsive to each individual user, not set in code.
I also would like to make the program pause after the call in "main" to "PassDB" to wait for "PassDB" to exit before continuing.
I would also like to make "PassDB" destroy itself after the "OK" button is pressed & the "username" & "password" set.
If that isn't enough for you, I would really like the program to search 2 different database tables, return their values & compare them to be sure that they are the same.
When I try & search 2 different tables, as in:
ResultSet rec = st.executeQuery(
                    "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                    + "WHERE (Title='Mr') ORDER BY ContactID");
               ResultSet rec2 = st.executeQuery(
                    "SELECT Subject, ContactID FROM Calls "
                    + "WHERE (Subject Is Not Null) ORDER BY ContactID")javac tells me that "ResultSet" is set to null 0
As always, I am extremely appreciative of any assistance you are able to offer.
Kind regards
duBedat
[email protected]

This is where I'm at now:
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.sql.*;
public class DBQuery {
     static String username = "" ;
     static String password = "" ;
     public static void main(String[] arguments) {
     PassDB UPass = new PassDB();
     String data = "jdbc:odbc:JavaTestDataBase";
     try {
          Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
          Connection conn = DriverManager.getConnection(data, "" + DBQuery.username, "" + DBQuery.password);
          Statement st = conn.createStatement();
          ResultSet rec = st.executeQuery(
          "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
          + "WHERE (Title='Mr') ORDER BY ContactID");
          /*     ResultSet rec2 = st.executeQuery(
               "SELECT Subject, ContactID FROM Calls "
               + "WHERE (Subject Is Not Null) ORDER BY ContactID");
          System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
          while(rec.next()) {
               System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
          st.close();
     catch (SQLException s) {
          System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
     catch (Exception e) {
          System.out.println("Error: " + e.toString() + e.getMessage());
class PassDB extends javax.swing.JFrame implements ActionListener {
     static boolean getOut = false;
     JTextField uname = new JTextField(10);
     JTextField pword = new JTextField(10);
     // JPasswordField pword = new JTextField(10);
     public PassDB() {
          super("duBe's database logon");
          setSize(220, 160);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          JPanel pane = new JPanel();
          JLabel unameLabel = new JLabel ("Username: ");
          JLabel pwordLabel = new JLabel ("Password: ");
          JButton submit = new JButton("OK");
          submit.addActionListener(this);
          pane.add(unameLabel);
          pane.add(uname);
          pane.add(pwordLabel);
          pane.add(pword);
          pane.add(submit);
          setContentPane(pane);
          while(getOut == false)
               setVisible(true);
     public void actionPerformed(ActionEvent evt) {
          PassDB clicked = (PassDB)evt.getSource();
          DBQuery.username = uname.getText();
          DBQuery.password = pword.getText();
          getOut = true;
}          Any advice is greatly appreciated
duBe

Problem setting up 5Ghz security on WRT610Nv2 2.00.00.B05

Similar Messages

Maybe you are looking for