Problem whit cisco 2921 + EVM-HD-8FXS/DID whit CUCM

Hello everyone.
I have the following problem that I am not able to resolve. I define a new connection BRI.
I can make calls seamlessly between the Cisco Unified Communications Manager (version: 8.5.1.10000-26) and Cisco 2921 (CISCO2921-V/K9).
But when you receive calls from BRI Cisco receives the call but the Cisco Unified Communications Manager does not tranfere for Ext
And I can not understand why. In other BRI interfaces do not have this problem.
This configuration here that I'm using.
Current configuration : 17238 bytes
! Last configuration change at 18:02:34 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname  <<omitted>>
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret 5  <<omitted>>
aaa new-model
aaa authentication login default none
aaa authentication login <<omitted>>
aaa accounting connection h323 start-stop group radius
aaa session-id common
clock timezone PORT 0 0
clock summer-time PORT recurring last Sun Mar 1:00 last Sun Oct 1:00
network-clock-participate slot 1
network-clock-participate wic 0
network-clock-participate wic 1
network-clock-participate wic 2
network-clock-participate wic 3
network-clock-select 1 BRI0/0/0
network-clock-select 2 BRI0/1/0
network-clock-select 3 BRI0/2/0
network-clock-select 4 BRI0/3/0
no ipv6 cef
ip source-route
ip cef
no ip domain lookup
ip domain name  <<omitted>>
multilink bundle-name authenticated
isdn switch-type basic-net3
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed- <<omitted>>
enrollment selfsigned
subject-name cn= <<omitted>>
revocation-check none
rsakeypair TP-self-signed- <<omitted>>
crypto pki certificate chain  <<omitted>>
<<omitted>>
      quit
voice-card 0
dsp services dspfarm
voice call send-alert
voice call disc-pi-off
voice call carrier capacity active
voice rtp send-recv
voice service voip
no ip address trusted authenticate
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
h323
modem passthrough nse codec g711ulaw
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class h323 1
  h225 timeout tcp establish 5
voice translation-rule 1
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 2
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
rule 4 /^21 <<omitted>>/ /21 <<omitted>>/
rule 5 /^21 <<omitted>>/ /21 <<omitted>>/
rule 6 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 3
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 4
rule 1 /^0/ /400/
rule 2 /^/ /21 <<omitted>>/
voice translation-rule 5
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 11
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 12
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /.*/ /21 <<omitted>>/
voice translation-rule 13
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 14
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 15
rule 1 /.*/ /21<<omitted>>/
voice translation-rule 21
rule 1 /^./ /0&/
voice translation-rule 22
rule 1 /^./ /0&/
voice translation-rule 25
rule 1 /^./ /0&/
|
voice translation-rule 23
rule 1 /^./ /0&/
voice translation-rule 24
rule 1 /^./ /0&/
voice translation-rule 32
rule 1 /^212104974/ /21 <<omitted>>/
rule 2 /.*/ /212104975/
voice translation-profile INLINE_EMPA
translate calling 22
translate called 2
voice translation-profile INLINE_EMPB
translate calling 23
translate called 3
voice translation-profile INLINE_EMPC
translate calling 25
translate called 5
voice translation-profile INLINE_EMPE
translate calling 24
translate called 4
voice translation-profile INLINE_EMPD
translate calling 21
translate called 1
voice translation-profile OUTLINE_EMPA
translate calling 12
voice translation-profile OUTLINE_EMPA_NT_FAX
translate calling 32
voice translation-profile OUTLINE_EMPB
translate calling 13
voice translation-profile OUTLINE_EMPC
translate calling 15
voice translation-profile OUTLINE_EMPE
translate calling 14
voice translation-profile OUTLINE_EMPD
translate calling 11
license udi pid CISCO2921/K9 sn  <<omitted>>
hw-module pvdm 0/0
hw-module sm 1
username admin privilege 15 password 0  <<omitted>>
redundancy
ip ssh time-out 60
ip ssh authentication-retries 2
class-map match-all Voz
match access-group 100
policy-map QoS
class Voz
  priority 200
  set precedence 5
class class-default
  fair-queue
gw-accounting aaa
attribute acct-session-id overloaded
acct-template callhistory-detail
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address  <<omitted>> 255.255.0.0
ip access-group BLOCK in
load-interval 30
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr  <<omitted>>
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
interface BRI0/0/0
description  EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/0/1
description Ecotel EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/0
description  EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation first-call
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/1
description  EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/0
description  EMPB N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/1
description  Ecotel EMPB N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/3/0
description  EMPE N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/3/1
description  Ecotel EMPA N
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/0
description B EMPC N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI1/1
description  Ecotel EMPE N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/2
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/3
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/4
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/5
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/6
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/7
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip rtcp report interval 500
ip access-list extended BLOCK
deny   ip any host <<omitted>>
deny   ip any host <<omitted>>
deny   ip any host <<omitted>>
deny   ip any host <<omitted>>
permit ip any any
ip radius source-interface GigabitEthernet0/0
radius-server host <<omitted>> auth-port 1647
radius-server host <<omitted>> acct-port 1647
radius-server key <<omitted>>
radius-server vsa send accounting
control-plane
voice-port 0/0/0
translation-profile incoming INLINE_EMPD
translation-profile outgoing OUTLINE_EMPD
compand-type a-law
cptone PT
voice-port 0/0/1
compand-type a-law
cptone PT
voice-port 0/1/0
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
voice-port 0/1/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA_NT_FAX
compand-type a-law
cptone PT
voice-port 0/2/0
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
voice-port 0/2/1
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 0/3/0
translation-profile incoming INLINE_EMPE
translation-profile outgoing OUTLINE_EMPE
compand-type a-law
cptone PT
voice-port 0/3/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 1/0/0
compand-type a-law
cptone PT
voice-port 1/0/1
compand-type a-law
cptone PT
voice-port 1/0/2
compand-type a-law
cptone PT
voice-port 1/0/3
compand-type a-law
cptone PT
voice-port 1/0/4
compand-type a-law
cptone PT
voice-port 1/0/5
compand-type a-law
cptone PT
voice-port 1/0/6
compand-type a-law
cptone PT
voice-port 1/0/7
compand-type a-law
cptone PT
voice-port 1/0/8
translation-profile incoming INLINE_EMPC
translation-profile outgoing OUTLINE_EMPC
compand-type a-law
cptone PT
voice-port 1/0/9
compand-type a-law
cptone PT
voice-port 1/0/10
compand-type a-law
cptone PT
voice-port 1/0/11
compand-type a-law
cptone PT
voice-port 1/0/16
compand-type a-law
cptone PT
voice-port 1/0/17
compand-type a-law
cptone PT
voice-port 1/0/18
compand-type a-law
cptone PT
voice-port 1/0/19
compand-type a-law
cptone PT
ccm-manager music-on-hold
no mgcp package-capability res-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp profile default
dial-peer voice 1 pots
description +++++ Dial-peer +++++
incoming called-number .
direct-inward-dial
port 0/0/0
dial-peer voice 10 pots
description touchwise
destination-pattern 1T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 20 pots
description globalmove
preference 1
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 30 pots
description globaltemp
shutdown
destination-pattern 3T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 40 pots
description EMPE
destination-pattern 4T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/3/0
dial-peer voice 100 voip
preference 1
destination-pattern .
session target ipv4:10.35.2.1
voice-class codec 1 
no vad
dial-peer voice 21 pots
description globalmove
preference 2
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 101 voip
preference 2
destination-pattern .
session target ipv4:10.35.2.2
voice-class codec 1 
no vad
dial-peer voice 24 pots
description globalmove
preference 1
destination-pattern 59[1236].......
port 0/3/1
forward-digits 9
dial-peer voice 25 pots
description globalmove
preference 1
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 26 pots
description globalmove
preference 2
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 27 pots
description globalmove
preference 1
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 28 pots
description globalmove
preference 2
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 34 pots
description globalTemp
preference 1
destination-pattern 39[1236].......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/1
forward-digits 9
dial-peer voice 35 pots
description globalTemp
preference 1
destination-pattern 300T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 37 pots
description globalTemp
preference 1
destination-pattern 3[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 14 pots
description empd
preference 1
destination-pattern 19386648.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 15 pots
description empd
preference 1
destination-pattern 19365483.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 16 pots
description empd
preference 1
destination-pattern 19341347.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 50 pots
description EMPC
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 1/0/8
gateway
timer receive-rtp 1200
gatekeeper
shutdown
call-manager-fallback
max-conferences 4 gain -6
transfer-system full-consult
ip source-address 10.35.2.250 port 2000
max-ephones 100
max-dn 300
transfer-pattern 09........
transfer-pattern 02........
transfer-pattern 0.........
transfer-pattern 000T
transfer-pattern 4...
keepalive 10
time-format 24
date-format dd-mm-yy
shutdown
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
login authentication touchwise
transport input ssh
line vty 5 15
login authentication touchwise
transport input ssh
scheduler allocate 20000 1000
ntp master 5
end

If t i "Translation Pattern Configuration" switch to another "Partition" existing or internal it works.
If change back for the new i create. It does not work.
So I must be some flaw  i made in Cisco Unified CM.

Similar Messages

  • EVM-HD-8FXS/DID as backup

    Customer wants 12 pots lines for backup in case the PRI is down. I was thinking of using EVM-HD-8FXS/DID which will give me 8 DIDs and 4 port FXO card or FXO expension module. The question is can I make outbound calls on these lines when configured as DIDs? Is there a better solution?
    Chris

    You should be able to use DID trunks (as long as telco provision them as DID trunks) and set all the FXS ports to DID mode. You get 8 base FXS ports on the EVM and you can either add 6 FXO cards or add a 3 FXS/4FXO card or another 8 port FXS port daughter card (expansion module). In DID mode, you wont get any dialtone (much like FXO)
    I am not sure if DID mode is available on the expansion cards. Also if you mix and match FXS and DID modes you have to take care of impedance settings. Check this link
    http://www.cisco.com/en/US/products/hw/modules/ps2617/products_configuration_example09186a0080513001.shtml
    HTH
    Sankar
    ---edited----
    I dont think you can configure any ports on the EM cards in DID mode. I strongly believe, you are limited to 8 DID ports (base FXS ports)

  • EVM-HD-8FXS/DID EXT MODULE

    HOW MANY FXS VOICE PORTS GIVE ME THE EVM-HD-8FXS/DID WITHOUT EM-HDA- EXPANSION MODULES?.
    THANKS.

    OK, IF I NEED 8 FXS PORTS AND 6 FXO PORTS, JUST NEED PURCHASE:
    1x EVM-HD-8FXS/DID plus
    1x EM-HDA-6FX0.
    RIGHT?
    Thanks.

  • EVM-HD-8FXS problem

    In router/gateway 3825 I have a EVM-HD-8FXS/DID card and I want it register with CallManager. I have on CallManager "AALN/S1/SU0/[email protected]", Device type "Cisco MGCP FXS Port" Status:"Rejected". Any idea why is it rejected?

    check ur Router if it has following commands
    ccm-manager mgcp
    ccm-manager config server
    ccm-manager config
    mgcp
    mgcp call-agent 2427 service-type mgcp version 0.1
    mgcp dtmf-relay voip codec all mode out-of-band
    Verify u have "ccm-manager config"

  • EVM-8FXS/DID

    Hello,
    I have a 2821 with a EVM-8FXS/DID installed on EVM slot with a blackbox panel, i have also conected a analog phone on port 7 (voice port 2/0/7) that is working fine, i also have conected a phone in por 0,1,2,3,4,5 but the phone does not work, i tryed to swith the phones but the problem seems to be related with port's 0,1,2,3,4,5.
    With show voice port summary I can see tha the port goes off-hook
    Can someone help me

    What is the P/N for for blackbox patch panel you are using?

  • Hallo guys, I have macbook pro buy march this years, now i have problem whit desktop sometime i recive green screen did some have idee what can be problem

    Hallo guys, I have macbook pro buy march this years, now i have problem whit desktop sometime i recive green screen did some have idee what can be problem

    You are still under warranty.  Call Apple Care.   
    #1 - You have 14 days from the date of purchase to return your computer with no questions asked. 
    #2 - You have 90 days of FREE phone tech support. 
    #3 - You have the standard one year Apple warranty. 
    #4 - If you've purchased an AppleCare Protection Plan, your warranty last for 3 years.   You can obtain AppleCare anytime up to the first year of the purchase of your computer.    
    Take FULL advantage of your warranty.  Posting on a message board should be done as a last resort and if you are out of warranty or Apple Care has expired.

  • Problem whit snapshot on Cisco video surveillance manager 6.3.2

    I have problems with cisco video surveillance 6.3.2.
    when making a snapshot, the file is saved but can not be displayed on the computer, anyone know why?

    we don't have release notes for 7.6 hotfix but BU has posted a Read me file for the same. you could find it on cisco.com, find the attached snap shot to access the read me file.
    Let me know, if you have any questions.

  • Problems whit port forward CS

    Hello,
    I have a huge problem whit my WRT54GX-V2, i cant get the router to work whit the ports of counter-strike. This is geting frustrating, it is the 2º model of the linksys routers i tested, and nothing.
    The port forward is configured, but there is no response.  i did remove the router, and it worked.
    What is going on? there is a endless list of conplaint against many of the routers of linksys, but no ansers.  
    please help !!!
    tanks

    Hello,
    My isp is Netcabo and the modem is a cable modem

  • Configuring - Cisco 2921 with Switch Module/POE PS and 3750-x 24 port switch

    This is what I have
    - Cisco 2921 router
             with SM-ES2-24-P switch module and
                     POE power supply
    -Cisco 3750x- 24 port Switch
    I have port G1/0 (which connects to 24p Switch Module port g0/26 logically) configured with 3 sub interfaces (management, User and VOIP)
    I want to connect 3750x to G0/1 on 2921 via fiber GBIC but want to use same three VLANs
    I can not daisy chain 3750x via the switch module because it does not have fiber port.
    I do not want to create another routed (g0/1) interface because I want to keep Users on both switches on the same subnet without further splitting the subnet in two.
    I hope I am not making this confusing.
    How can I bridge g1/0 and g0/1 so I can pass vlan traffic between two switches?
    Second problem i have is ...
    I have a VOIP connected to switch module (SM) and it is not getting any power.
    I went in to all the interfaces on SM and issued power inline auto command
    On the SM (sh power inline) - available is 0.0(w)
    on the 2921 (sh power inline)
       - power supply status is good,
       - maximun power available is 280.
       - interface G1/0( which connects to SM)
          *device is unknown
          * powered off
         * allocated 0.0 watts.
    I already tried resetting SM
    Is there any other command I need to issue?
    thanks for your help.

    I'm having a similar issue. I can get trunked connectivity between the switch module and the router if I put the IP address on the router sub interface, but not if I put it on a VLAN interface. I was hoping to have it on a VLAN sub interface on the router so I could use Gig0/1 and Gig0/2 to connect other switches and have them on the same VLANs. I'm using Gig1/0 on the router side and Gig0/51 on the switch side (48-port module).
    Any help? Am I on the wrong track altogether?

  • Hey i have problem white msi x99s gaming 7 main board led debug cod 04

    hey me is Jacob. and i have thes problem White me msi x99s gaming 7 that i get code 04 in the led debug when i power it up and then it whont boot up as normal and it stands on the code 04 in the led debug on the motherboard and it just came Yesterday. and it have been runing for 7 months White no problem and that is that  i have the time I have had it in. and when the led debug code 04 in the manual it say power on south bridge initiation. me  bios version on me msi x99s gaming 7 is H.90

    Board: MSI x99s gaming 7
    Bios: Version H.90
    VGA: MSI 970GTX gaming 4g, MSI 750TIGTX GAMING 2 GB
    PSU:   Cooler Master G750M, 750W PSU
    Intel Core i7-5820k Intel® Haswell-E 3.3GHz (3.6GHz Turbo Boost) LGA 2011-v3
    MEM: Crucial DDR4 16GB 2133MHz Quad-channel KIT
    HDD: samsung 840 evo 120gb SSD and Seagate® Desktop SSHD 1TB
    COOLER: Intel TS13A Air Cooler
    OS: Windows 8.1 64bit Professional
    i have tried:
    1. Tested power supply with a Thermaltake power supply tester, all voltages are within range, including the CPU power connector, which i did double check to be plugged in.
    2. Tried the video card in another PC, working fine, also tried it in each pci express slot (four of them) on the MSI X99S GAMING 7 board.
    3. Tried resetting the bios and have also tried booting with just one memory stick in Dimm slot 1
    4. Tried powering up the board out of the case with just the power supply, video and memory connected.
    and it still get the samme problem as before and still stand on code 04 and still not boot up.

  • When I attempt to open lightroom I recive this message: [ Lightroom encountered an error whenreading from itspreviw cache and needs to quit.Lightroom will atempt to fix this problem next time it launches.] I did this a few times but no resoulve

    When I attempt to open lightroom I recive this message: [ Lightroom encountered an error whenreading from itspreviw cache and needs to quit.Lightroom will atempt to fix this problem next time it launches.] I did this a few times but no resoulve

    It isn't a file, it's a folder. It will have the same name as your catalog, but will have the extension data. It will be in the same folder along with your catalog. If you need to use the search feature to search for *.lrdata.

  • I have a problem with my Iphone 4s since I did my first update at your Itunes, the bluetooth and the WiFi it is not workinhg anymore.  It is sad that companies like apple are not able to support thier sofware and business.  I went to a apple store at Sout

    I have a problem with my Iphone 4s since I did my first update at your Itunes, the bluetooth and the WiFi it is not workinhg anymore.
    It is sad that companies like apple are not able to support thier sofware and business.
    I went to a apple store at South Park, Charlotte NC,
    and found out the worst customer service (in my case)
    They don't have answers and don't understand about  "dont let any customer go away sad or mad"
    I explain to them that I did everything they said to fix the problem, even to dounload the iOS 6.1.3
    that was supposed to fix the problem.
    they said fix the problem in other phones but not in mine.
    So here I am with no wifi and bluetooth, with apple technicians and experts that don't know what to do with the problem that the sofware they developed cause in my iphone 4s.
    and the solution is for me to pay $199.00 US dollars for a problem that I did not cause.
    wich means to buy something else from apple to fix a problem that it is not my fault.
    Great! what a convenient solution.
    I would like to have an answer from you guys and see if someone there have a better answer for me that shows support, values and integrity as a grest company with solutions for your customers.
    Dont think that I want a new phone, I want mine fixed if is possible.
    Thank you very much and God Bless you!

    Apple isnt here. this is a user based forum for technical questions. The solution is to restart, reset, and restore as new which is in the manual after that get it replaced for hard ware failure. if your within your one year warranty its replaced if it is out of the warranty then it is 199$

  • Im trying to download itunes 10.5 but keep getting error message that says: There is a problem with this Windows Installer package. A problem run as part of the setup did not finish as expected. Contact your support personnel or package vendor.

    im trying to download itunes 10.5 but keep getting error message that says: There is a problem with this Windows Installer package. A problem run as part of the setup did not finish as expected. Contact your support personnel or package vendor. I am using windows XP 32 bit, all the other computers in my house downloaded just fine, no problems, however this is the computer my iphone is set up to, ive tried doing a virus scan, windows update, downloading other things, updating everything possible, everything works fine, its just itunes that wont download, anyone have any other ideas?

    Yes, I had found a similar solution also.  I'm running XP Pro, SP3.  I went Control Panels/ Add-Remove programmes/apple software update/ change/ repair.  Then run the 10.5 exe.
    While the programme updated from version 8 of iTunes, my new iTunes is now a mess.  Not all of my music was in the same folder previously but it all showed up on iTunes.  Now many albums have been left out, some have only a few tracks and some have two copies of some tracks as well as having other tracks missing.  I haven't begun to work on that.

  • Cr52-A2 problem whit the new firmware(1.80D)

    hello all
    i having a problem whit my cd-rw
    maybe one of you guys can help me cuse i'm breaking my had hear  
    i flashed the firmware from 1.60D to 1.80D
    and my cd-rw stop working  
     the chiki boaster doesn't want me to open him also
     i want the old version  
    give me back my 1.60D
    p.s.
    maybe ther's a way to reset the cd-rw
    ha  
    what are you fox thinking

    Hi
    There is a note at the bottom of the page:
    Note: You should not update your firmware unless you have
    have flash experience with your optical drive.
    But, I will try to download firmware from my girlsfriend's drive. That is the same type. And think that is 160D.
    Tsibi

  • Problem whit ora-12637!

    Hi, I have a problem whit this error code when I execute my form from Forms Builder. Im using Forms 6i. First, i open my form, then i connect to compile, and execute my form, but when the system open the forms runtime i get this error code.
    In SQL Developer i connect whitout any problem, and whit forms 6i too, Why not whit Forms Runtime???
    Regards!!

    Unfortunitely, that doesn't help.
    To anyone reading this thread, "6i", "10g", "11i", "12i"" are all product marketing references. They do not represent a product version. Knowing the exact product version is very important when trying to troubleshoot a problem. In this case for example, telling us that you are using a 10g db could potentially mean that you are using one many different releases (i.e. 10.1.x, 10.2.x). And of course, this does not take in to account any patches which may have been applied.
    All I can offer is this, Forms 6.0.8.x is not certified or supported for use with 10.2.x databases. However, with Forms 6.0.8.25 or newer you can use 10.1.x databases.
    I would recommend that you start with this information. If this doesn't help, please consider responding to the remaining questions in my previous posting.

Maybe you are looking for

  • TS3212 Tried to dowload and install ITunes multiple times-can't get it to work

    I have followed instructions to take out ITunes then download-won't install message MSVCR80.dll missing-can you help??

  • Allowing for Alternate Correct "Answers"

    Don't know which forum this falls under, sorry: I want to create a training simulation (and actually, an assessment simulation too) where the user can select one of a variety of correct methods for accomplishing a task. How do I program the multiple

  • How do you fix incorrect date fields in excel?

    They appear incorrect in the viewer from and email attachment.  They should read 05/01/2012  (MM/DD/YYYY)but when you view it, they are a ##### digit number. When viewing the report in a full excel version, the dates are correct.   How  do we fix the

  • ALV Tree Report--clicking on a row....

    Hello Experts, i have a alv tree report.my requirement is, "Selecting a row means clicking on record  and then click on a another button called YES ,For other functionality i need to capture the row '. How can i solve this  problem. Thanks, Sridhar.

  • Why is my "Combined PDF" file size smaller than the original files?

    Hello! I am trying to combine two individual PDF files into a single PDF. Each file is 32mb, however when I use acrobat to combine them, the newly created "combined" file is only 19mb. I believe I've taken the necessary steps to ensure no degradation