EVM-HD-8FXS problem
In router/gateway 3825 I have a EVM-HD-8FXS/DID card and I want it register with CallManager. I have on CallManager "AALN/S1/SU0/[email protected]", Device type "Cisco MGCP FXS Port" Status:"Rejected". Any idea why is it rejected?
check ur Router if it has following commands
ccm-manager mgcp
ccm-manager config server
ccm-manager config
mgcp
mgcp call-agent 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
Verify u have "ccm-manager config"
Similar Messages
-
Customer wants 12 pots lines for backup in case the PRI is down. I was thinking of using EVM-HD-8FXS/DID which will give me 8 DIDs and 4 port FXO card or FXO expension module. The question is can I make outbound calls on these lines when configured as DIDs? Is there a better solution?
ChrisYou should be able to use DID trunks (as long as telco provision them as DID trunks) and set all the FXS ports to DID mode. You get 8 base FXS ports on the EVM and you can either add 6 FXO cards or add a 3 FXS/4FXO card or another 8 port FXS port daughter card (expansion module). In DID mode, you wont get any dialtone (much like FXO)
I am not sure if DID mode is available on the expansion cards. Also if you mix and match FXS and DID modes you have to take care of impedance settings. Check this link
http://www.cisco.com/en/US/products/hw/modules/ps2617/products_configuration_example09186a0080513001.shtml
HTH
Sankar
---edited----
I dont think you can configure any ports on the EM cards in DID mode. I strongly believe, you are limited to 8 DID ports (base FXS ports) -
EVM-HD-8FXS/DID EXT MODULE
HOW MANY FXS VOICE PORTS GIVE ME THE EVM-HD-8FXS/DID WITHOUT EM-HDA- EXPANSION MODULES?.
THANKS.OK, IF I NEED 8 FXS PORTS AND 6 FXO PORTS, JUST NEED PURCHASE:
1x EVM-HD-8FXS/DID plus
1x EM-HDA-6FX0.
RIGHT?
Thanks. -
Problem whit cisco 2921 + EVM-HD-8FXS/DID whit CUCM
Hello everyone.
I have the following problem that I am not able to resolve. I define a new connection BRI.
I can make calls seamlessly between the Cisco Unified Communications Manager (version: 8.5.1.10000-26) and Cisco 2921 (CISCO2921-V/K9).
But when you receive calls from BRI Cisco receives the call but the Cisco Unified Communications Manager does not tranfere for Ext
And I can not understand why. In other BRI interfaces do not have this problem.
This configuration here that I'm using.
Current configuration : 17238 bytes
! Last configuration change at 18:02:34 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname <<omitted>>
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret 5 <<omitted>>
aaa new-model
aaa authentication login default none
aaa authentication login <<omitted>>
aaa accounting connection h323 start-stop group radius
aaa session-id common
clock timezone PORT 0 0
clock summer-time PORT recurring last Sun Mar 1:00 last Sun Oct 1:00
network-clock-participate slot 1
network-clock-participate wic 0
network-clock-participate wic 1
network-clock-participate wic 2
network-clock-participate wic 3
network-clock-select 1 BRI0/0/0
network-clock-select 2 BRI0/1/0
network-clock-select 3 BRI0/2/0
network-clock-select 4 BRI0/3/0
no ipv6 cef
ip source-route
ip cef
no ip domain lookup
ip domain name <<omitted>>
multilink bundle-name authenticated
isdn switch-type basic-net3
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed- <<omitted>>
enrollment selfsigned
subject-name cn= <<omitted>>
revocation-check none
rsakeypair TP-self-signed- <<omitted>>
crypto pki certificate chain <<omitted>>
<<omitted>>
quit
voice-card 0
dsp services dspfarm
voice call send-alert
voice call disc-pi-off
voice call carrier capacity active
voice rtp send-recv
voice service voip
no ip address trusted authenticate
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
h323
modem passthrough nse codec g711ulaw
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class h323 1
h225 timeout tcp establish 5
voice translation-rule 1
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 2
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
rule 4 /^21 <<omitted>>/ /21 <<omitted>>/
rule 5 /^21 <<omitted>>/ /21 <<omitted>>/
rule 6 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 3
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 4
rule 1 /^0/ /400/
rule 2 /^/ /21 <<omitted>>/
voice translation-rule 5
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 11
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 12
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /.*/ /21 <<omitted>>/
voice translation-rule 13
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 14
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 15
rule 1 /.*/ /21<<omitted>>/
voice translation-rule 21
rule 1 /^./ /0&/
voice translation-rule 22
rule 1 /^./ /0&/
voice translation-rule 25
rule 1 /^./ /0&/
|
voice translation-rule 23
rule 1 /^./ /0&/
voice translation-rule 24
rule 1 /^./ /0&/
voice translation-rule 32
rule 1 /^212104974/ /21 <<omitted>>/
rule 2 /.*/ /212104975/
voice translation-profile INLINE_EMPA
translate calling 22
translate called 2
voice translation-profile INLINE_EMPB
translate calling 23
translate called 3
voice translation-profile INLINE_EMPC
translate calling 25
translate called 5
voice translation-profile INLINE_EMPE
translate calling 24
translate called 4
voice translation-profile INLINE_EMPD
translate calling 21
translate called 1
voice translation-profile OUTLINE_EMPA
translate calling 12
voice translation-profile OUTLINE_EMPA_NT_FAX
translate calling 32
voice translation-profile OUTLINE_EMPB
translate calling 13
voice translation-profile OUTLINE_EMPC
translate calling 15
voice translation-profile OUTLINE_EMPE
translate calling 14
voice translation-profile OUTLINE_EMPD
translate calling 11
license udi pid CISCO2921/K9 sn <<omitted>>
hw-module pvdm 0/0
hw-module sm 1
username admin privilege 15 password 0 <<omitted>>
redundancy
ip ssh time-out 60
ip ssh authentication-retries 2
class-map match-all Voz
match access-group 100
policy-map QoS
class Voz
priority 200
set precedence 5
class class-default
fair-queue
gw-accounting aaa
attribute acct-session-id overloaded
acct-template callhistory-detail
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address <<omitted>> 255.255.0.0
ip access-group BLOCK in
load-interval 30
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr <<omitted>>
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
interface BRI0/0/0
description EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/0/1
description Ecotel EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/0
description EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation first-call
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/1
description EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/0
description EMPB N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/1
description Ecotel EMPB N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/3/0
description EMPE N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/3/1
description Ecotel EMPA N
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/0
description B EMPC N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI1/1
description Ecotel EMPE N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/2
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/3
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/4
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/5
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/6
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/7
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip rtcp report interval 500
ip access-list extended BLOCK
deny ip any host <<omitted>>
deny ip any host <<omitted>>
deny ip any host <<omitted>>
deny ip any host <<omitted>>
permit ip any any
ip radius source-interface GigabitEthernet0/0
radius-server host <<omitted>> auth-port 1647
radius-server host <<omitted>> acct-port 1647
radius-server key <<omitted>>
radius-server vsa send accounting
control-plane
voice-port 0/0/0
translation-profile incoming INLINE_EMPD
translation-profile outgoing OUTLINE_EMPD
compand-type a-law
cptone PT
voice-port 0/0/1
compand-type a-law
cptone PT
voice-port 0/1/0
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
voice-port 0/1/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA_NT_FAX
compand-type a-law
cptone PT
voice-port 0/2/0
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
voice-port 0/2/1
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 0/3/0
translation-profile incoming INLINE_EMPE
translation-profile outgoing OUTLINE_EMPE
compand-type a-law
cptone PT
voice-port 0/3/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 1/0/0
compand-type a-law
cptone PT
voice-port 1/0/1
compand-type a-law
cptone PT
voice-port 1/0/2
compand-type a-law
cptone PT
voice-port 1/0/3
compand-type a-law
cptone PT
voice-port 1/0/4
compand-type a-law
cptone PT
voice-port 1/0/5
compand-type a-law
cptone PT
voice-port 1/0/6
compand-type a-law
cptone PT
voice-port 1/0/7
compand-type a-law
cptone PT
voice-port 1/0/8
translation-profile incoming INLINE_EMPC
translation-profile outgoing OUTLINE_EMPC
compand-type a-law
cptone PT
voice-port 1/0/9
compand-type a-law
cptone PT
voice-port 1/0/10
compand-type a-law
cptone PT
voice-port 1/0/11
compand-type a-law
cptone PT
voice-port 1/0/16
compand-type a-law
cptone PT
voice-port 1/0/17
compand-type a-law
cptone PT
voice-port 1/0/18
compand-type a-law
cptone PT
voice-port 1/0/19
compand-type a-law
cptone PT
ccm-manager music-on-hold
no mgcp package-capability res-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp profile default
dial-peer voice 1 pots
description +++++ Dial-peer +++++
incoming called-number .
direct-inward-dial
port 0/0/0
dial-peer voice 10 pots
description touchwise
destination-pattern 1T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 20 pots
description globalmove
preference 1
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 30 pots
description globaltemp
shutdown
destination-pattern 3T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 40 pots
description EMPE
destination-pattern 4T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/3/0
dial-peer voice 100 voip
preference 1
destination-pattern .
session target ipv4:10.35.2.1
voice-class codec 1
no vad
dial-peer voice 21 pots
description globalmove
preference 2
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 101 voip
preference 2
destination-pattern .
session target ipv4:10.35.2.2
voice-class codec 1
no vad
dial-peer voice 24 pots
description globalmove
preference 1
destination-pattern 59[1236].......
port 0/3/1
forward-digits 9
dial-peer voice 25 pots
description globalmove
preference 1
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 26 pots
description globalmove
preference 2
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 27 pots
description globalmove
preference 1
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 28 pots
description globalmove
preference 2
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 34 pots
description globalTemp
preference 1
destination-pattern 39[1236].......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/1
forward-digits 9
dial-peer voice 35 pots
description globalTemp
preference 1
destination-pattern 300T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 37 pots
description globalTemp
preference 1
destination-pattern 3[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 14 pots
description empd
preference 1
destination-pattern 19386648.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 15 pots
description empd
preference 1
destination-pattern 19365483.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 16 pots
description empd
preference 1
destination-pattern 19341347.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 50 pots
description EMPC
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 1/0/8
gateway
timer receive-rtp 1200
gatekeeper
shutdown
call-manager-fallback
max-conferences 4 gain -6
transfer-system full-consult
ip source-address 10.35.2.250 port 2000
max-ephones 100
max-dn 300
transfer-pattern 09........
transfer-pattern 02........
transfer-pattern 0.........
transfer-pattern 000T
transfer-pattern 4...
keepalive 10
time-format 24
date-format dd-mm-yy
shutdown
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
login authentication touchwise
transport input ssh
line vty 5 15
login authentication touchwise
transport input ssh
scheduler allocate 20000 1000
ntp master 5
endIf t i "Translation Pattern Configuration" switch to another "Partition" existing or internal it works.
If change back for the new i create. It does not work.
So I must be some flaw i made in Cisco Unified CM. -
Configuring a EVM-HDA-6FXO for power failure
I want to add a EVM-HDA-6FXO to an exsiting EVM-HDA-8FXS/DID so if power goes out I can still have the FXO ports provide dial tone to the FXS ports.
Two emergency lines NPA-NXX-1000 comes in as a FXO and goes out a FXS port.
Can this be done. And does it work if the power is off to the router.The FXO expansion module supports a power failure port that connects directly to the central office (CO) in case of failure.
-
Hi All ,
Just a quick one, i need to connect 32 Analog trunk lines to a PABX and 4 PRI's to the PSTN. any Suggestions on which Cards i could use on the ISR to achieve this
Thanks in AdvanceHi,
from the PBX point of view, trunk lines are FXO, that is, analog lines that normally go to the pstn. This means the voice gateway will need FXS ports.
If this is your requirement, be aware that the integration may suffer of problems, for example you will not be able to give DID to the PBX.
Anyway, considering the density, the minimum you can use is a 2821 with EVM-HD-8FXS/DID + 2 x EM-HDA-8FXS, 2 x VIC-4FXS, 2 x VWIC2-2T1E1, 1 x PVDM2-32.
Hope this helps, please rate post if it does! -
I'm having trouble getting one of my clients' analog endpoints to register in CME. There are at least another dozen SCCP analog devices configured and they all seem to work fine. According to the debugs inbound calls are routing appropriately but because the SCCP endpoint isn't registered the port isn't ringing. I seem to have spare DSPs for the port to use. Any ideas? They're running 12.4(22)T and the analog connectivity is provided by an EVM-HD-8FXS/DID with EM-HDA-8FXS daughter cards.
Here are the relevant configs:
stcapp register capability 1/0/0 modem-passthrough
stcapp register capability 1/0/1 modem-passthrough
stcapp register capability 1/0/2 modem-passthrough
stcapp register capability 1/0/3 modem-passthrough
stcapp register capability 1/0/4 modem-passthrough
stcapp register capability 1/0/5 modem-passthrough
stcapp register capability 1/0/6 modem-passthrough
stcapp register capability 1/0/7 modem-passthrough
stcapp register capability 1/0/8 modem-passthrough
stcapp register capability 1/0/9 modem-passthrough
stcapp register capability 1/0/10 modem-passthrough
stcapp register capability 1/0/11 modem-passthrough
stcapp register capability 1/0/12 modem-passthrough
stcapp register capability 1/0/13 modem-passthrough
stcapp register capability 1/0/14 modem-passthrough
stcapp register capability 1/0/15 modem-passthrough
stcapp register capability 1/0/16 modem-passthrough
stcapp register capability 1/0/17 modem-passthrough
stcapp register capability 1/0/18 modem-passthrough
stcapp register capability 1/0/19 modem-passthrough
stcapp register capability 1/0/20 modem-passthrough
stcapp register capability 1/0/21 modem-passthrough
stcapp register capability 1/0/22 modem-passthrough
stcapp register capability 1/0/23 modem-passthrough
stcapp ccm-group 1
stcapp
voice-port 1/0/0
timeouts ringing infinity
voice-port 1/0/1
timeouts ringing infinity
voice-port 1/0/2
timeouts ringing infinity
voice-port 1/0/3
timeouts ringing infinity
voice-port 1/0/4
timeouts ringing infinity
voice-port 1/0/5
timeouts ringing infinity
voice-port 1/0/6
timeouts ringing infinity
voice-port 1/0/7
timeouts ringing infinity
voice-port 1/0/8
timeouts ringing infinity
voice-port 1/0/9
timeouts ringing infinity
voice-port 1/0/10
timeouts ringing infinity
voice-port 1/0/11
timeouts ringing infinity
voice-port 1/0/12
timeouts ringing infinity
voice-port 1/0/13
timeouts ringing infinity
voice-port 1/0/14
timeouts ringing infinity
voice-port 1/0/15
timeouts ringing infinity
voice-port 1/0/16
timeouts ringing infinity
voice-port 1/0/17
timeouts ringing infinity
voice-port 1/0/18
timeouts ringing infinity
voice-port 1/0/19
timeouts ringing infinity
voice-port 1/0/20
timeouts ringing infinity
voice-port 1/0/21
timeouts ringing infinity
voice-port 1/0/22
timeouts ringing infinity
voice-port 1/0/23
timeouts ringing infinity
dial-peer voice 999100 pots
service stcapp
port 1/0/0
dial-peer voice 999101 pots
service stcapp
port 1/0/1
dial-peer voice 999102 pots
service stcapp
port 1/0/2
dial-peer voice 999103 pots
service stcapp
port 1/0/3
dial-peer voice 999104 pots
service stcapp
port 1/0/4
dial-peer voice 999105 pots
service stcapp
port 1/0/5
dial-peer voice 999106 pots
service stcapp
port 1/0/6
dial-peer voice 999107 pots
service stcapp
port 1/0/7
dial-peer voice 999108 pots
service stcapp
port 1/0/8
dial-peer voice 999109 pots
service stcapp
port 1/0/9
dial-peer voice 999110 pots
service stcapp
port 1/0/10
dial-peer voice 999111 pots
service stcapp
port 1/0/11
dial-peer voice 999112 pots
service stcapp
port 1/0/12
dial-peer voice 999113 pots
service stcapp
port 1/0/13
dial-peer voice 999114 pots
service stcapp
port 1/0/14
dial-peer voice 999115 pots
service stcapp
port 1/0/15
dial-peer voice 999116 pots
service stcapp
port 1/0/16
dial-peer voice 999117 pots
service stcapp
port 1/0/17
dial-peer voice 999118 pots
service stcapp
port 1/0/18
dial-peer voice 999119 pots
service stcapp
port 1/0/19
dial-peer voice 999120 pots
service stcapp
port 1/0/20
dial-peer voice 999121 pots
service stcapp
port 1/0/21
dial-peer voice 999122 pots
service stcapp
port 1/0/22
dial-peer voice 999123 pots
service stcapp
port 1/0/23
ephone-dn 61 dual-line
number 2566
label Fax - 2566
description 5137922566
name Fax
ephone 61
device-security-mode none
mac-address C863.D76B.1407
max-calls-per-button 2
type anl
button 1:61
Inbound call debugs/show commands:
Voice-Gateway#debug voice dialpeer inout
Excerpt:
Result=SUCCESS(0)
List of Matched Outgoing Dial-peer(s):
1: Dial-peer Tag=20061
Voice-Gateway#sh dial-peer voice summary
Excerpt:
20061 pots up up 2566$ 0 50/0/61
Voice-Gateway#sh voice port sum | inc 50/0/61
50/0/61 1 efxs up up on-hook idle y
50/0/61 2 efxs up up on-hook idle y
And ephone status:
ephone-61[60] Mac:C863.D76B.1407
TCP socket:[-1] activeLine:0 UNREGISTERED
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:0
IP:0.0.0.0 0 Unknown 0 keepalive 0 max_line 0
Preferred Codec: g711ulaw
And ephone debugs:
VoiceGateway#sh debug
EPHONE error debugging is enabled
EPHONE registration debugging is enabled
for ephones C863.D76B.1407
VoiceGateway#term mon
VoiceGateway#peer_vdb is NULL for DN 69, chan 1 at SkinnyIsPeerNonSCCPpeer_vdb is NULL for DN 69, chan 1 at SkinnyIsPeerNonSCCPpeer_vdb is NULL for DN 40, chan 1 at SkinnyIsPeerNonSCCPpeer_vdb is NULL for DN 47, chan 1 at SkinnyIsPeerNonSCCP peer_vdb is NULL for DN 47, chan 1 at SkinnyIsPeerNonSCCPpeer_vdb is NULL for DN 40, chan 1 at SkinnyIsPeerNonSCCPpeer_vdb is NULL for DN 47, chan 1 at SkinnyIsPeerNonSCCPpeer_vdb is NULL for DN 69, chan 1 at SkinnyIsPeerNonSCCP
VoiceGateway#peer_vdb is NULL for DN 69, chan 1 at SkinnyIsPeerNonSCCP
show voice dsp group all:
DSP groups on slot 0:
dsp 1:
State: UP, firmware: 23.8.0
Max signal/voice channel: 16/16
Max credits: 240
num_of_sig_chnls_allocated: 16
Transcoding channels allocated: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 240, reserved credits: 0
Signaling channels allocated: 16
Voice channels allocated: 0
Credits used: 0
dsp 2:
State: UP, firmware: 23.8.0
Max signal/voice channel: 16/16
Max credits: 240
num_of_sig_chnls_allocated: 16
Transcoding channels allocated: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 240, reserved credits: 0
Signaling channels allocated: 16
Voice channels allocated: 0
Credits used: 0
dsp 5:
State: UP, firmware: 23.8.0
Max signal/voice channel: 16/16
Max credits: 240
num_of_sig_chnls_allocated: 16
Transcoding channels allocated: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 240, reserved credits: 0
Signaling channels allocated: 16
Voice channels allocated: 0
Credits used: 0
dsp 6:
State: UP, firmware: 23.8.0
Max signal/voice channel: 16/16
Max credits: 240
num_of_sig_chnls_allocated: 16
Transcoding channels allocated: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 240, reserved credits: 0
Signaling channels allocated: 16
Voice channels allocated: 0
Credits used: 0
dsp 7:
State: UP, firmware: 23.8.0
Max signal/voice channel: 16/16
Max credits: 240
num_of_sig_chnls_allocated: 8
Transcoding channels allocated: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 240, reserved credits: 0
Signaling channels allocated: 8
Voice channels allocated: 0
Credits used: 0
dsp 8:
State: UP, firmware: 23.8.0
Max signal/voice channel: 16/16
Max credits: 240
num_of_sig_chnls_allocated: 0
Transcoding channels allocated: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 240, reserved credits: 0
Signaling channels allocated: 0
Voice channels allocated: 0
Credits used: 0
DSP groups on slot 1:
DSP groups on slot 2:
This command is not applicable to slot 2
0 DSP resource allocation failureHi Phil,
Try removing all your stcapp configuration and just create a dial-peer voice pots XXX and place the port command in it, along with the extension number.
example.
dial-peer voice pots 999100
description # Analogue Phone 1 #
destination-pattern 2566$
port 1/0/1
As long as your translation patterns are correct an imcoming call will ring the analogue device connected to port 1/0/1
stcapp allows analogue ports to be regsitered to a call control server, Ive only seen this with CUCM, and with failover to SRST/CME in both cases you do have to add extra commands. But give the above a try and should be right to make and receive calls.
Cheers
Ben
Please rate is this post is useful -
Good day, we have a new CCME 3845 Router including VIC2-4FXO,NM-HD-2V,EVM-HD-8FXS/DID,EM-HDA-6FXO modules, this will be used for our new project. Is it possible that the CCME Router will work well on IP Phones even without the AIM-CUE, because that is the only remaining device that need to install on the Router and we want to install now the Router at the Site while we are waiting for the AIM-CUE to arrive the IP Phones should work. Thanks and I will wait for your reply.
Hi Mahmoud,
You should be fine to get started without the AIM-CUE. This will only prevent the setup of the Voicemail potion of the install :)
Cisco CallManager Express/Cisco Unity Express Configuration Example
http://www.cisco.com/en/US/products/sw/voicesw/ps5520/products_configuration_example09186a008037f2a9.shtml
Cisco CallManager Express 3.0 and Later Integration with Cisco Unity Express
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/prod_installation_guide09186a008059fb5f.html
Hope this helps!
Rob -
Maximum 3845 voice card capacity?
Hello,
I am trying to build a 3845 of the following spec.with the configurator tool.
in the NM slots:
2x EVM-HD-8FXS/DID each with 2x EM3-HDA-8FXS/DID
2x NM-HD-2V each with 2x VIC2-2BRI-NT/TE
in the HWIC slots:
1x VIC2-2BRI-NT/TE
1x HWIC-4ESW
I specify IOS upgrade to S384RSPSK9-12424T so that the EM3-HDA is supported.
But when I finally click check configuration, it says there are only 4 HWIC slots available in CISCO3800, it doesn't appear to take into account that 4 of them are going into the NM-HD-2V modules.
Is this a configurator bug?
Now someone has told me that the 3845 doesn't support 2x EVM-HD-8FXS/DID each with 2x EM3-HDA-8FXS/DID as well.
Is this true or not?
HELP!
PaulI thought that the VG224/248 were non-preferred (going end-of-life) as the newer routers (28xx,38xx,29xx,39xx) have absorbed the functionality into their capability.
Customer wants to remain on analog handsets and TDM for voice, so VOIP is not an option.
Unfortunately, I have a requirement to interface to 8 ISDN BRI user devices, BRI is an essential component. I am using E1 for the PSTN trunking.
So, pushing the envelope or not, does anyone know if a 3845 can give me 48x analog voice ports, 8x BRI ports, 1x E1 port and 4x Ethernet switch ports? If so, what modules do I need to achieve this? -
FAX Analog line for the Router
Hi NetPro.
May i know that if i have 22 numbers of FAX Analog lines which i module should i add on into the router ? and how many ports which can fullfill the 22 lines of FAX Analog lines.
example : EVM-HD-8FXS/DID ... etc
Thanks
Regards,
KittenAre you connecting 22 analog faxes (FXS), or are you connected to 22 analog POTS lines (FXO)?
EVM can only do 16 max FXS or 8 max FXS + 6 max FXO.
which router do you have?
If FXS, consider getting 24 port VG224 http://www.cisco.com/en/US/prod/collateral/voicesw/ps6790/gatecont/ps2250/ps5516/product_data_sheet09186a00801d87f6.html -
Hello All,
I would like to repurpose an old 3845 WAN router we have here at work to support FXS channels, but I'm not 100% sure on what cards would get me the most channels. I've read in the 3845 product sheet that it can support 88 FXS ports, but the highest density card I can seem to find only supports 8 FXS ports, the EVM-HD-8FXS/DID. Could anyone tell me what combination of cards would get me up to 32-64 FXS channels?
This router already has a PVDM2-64 module and is running "C3845-ADVENTERPRISEK9-M 12.4.(15)T3" for its image.Hi Zach,
The 3845 supports 2 EVM modules.
Ref:
http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/high-density-voice-fax-network-modules/prod_qas0900aecd8016c487.html -
Hi guys.
We have a current requirement that has the following specifications.
Minimum of 20 Analog trunks, 1 x E1 PRI ISDN trunk, with SIP license (60 licenses), with IVR, call data recording
I have configured a 2911 with the appropriate licenses in CCW. But, how can I come up with a solution for 20 analog trunks? I am not yet familiar with this.
Thanks in advance.EVM-HD-8FXS/DID High density voice/fax extension module -8 FXS/DID
EVM-HD-8FXS/DID
The Cisco High-Density Extension Module for voice and fax
has 8 FXS and DID ports. Individual ports on the basebo
ard
module can be configured for FXS or DID signaling. Adj
acent ports should share the same configuration to avoid i
mpedance
setting conflicts. A change to the impedance setting for o
ne port, changes the setting on the adjacent port. Pair
ed ports are: 0
and 1; 2 and 3; 4 and 5; 6 and 7.
An on-premises FXS interface connects directly to a standar
d telephone, fax machine, or similar device and supplies
ring,
voltage, and dial tone. Signaling support available in
FXS mode includes loop-start and ground-start. DID tru
nks from the
central office can be connected to the Cisco High-Density E
xtension Module baseboard for off-premises connections.
Signaling support available in DID mode includes immedi
ate, delay dial, and wink start.
Users plug in up to two expansion modules in any combina
tion to increase the voice and fax capacity of the Cisco Hi
gh-
Density Extension Module baseboard.
or
EM3-HDA-8FXS/DID 8-port voice/fax expansion module-FXS/DID
EM3-HDA-8FXS/DID
This 8-port FXS/DID Voice and Fax Expansion Module pro
vides on-premises FXS signaling to connect directly to a sta
ndard
telephone, fax machine, or similar device and supplies ri
ng, voltage, and dial tone. Signaling support availabl
e in FXS mode
includes loop-start and ground-start. This expansion modu
le also works with the Cisco High-Density Analog Voice an
d Fax
Network Module (part number NM-HDA-4FXS).
DID trunks from the central office can be connected to t
he Cisco Voice and Fax Expansion Module for off-premises
connections. Signaling support available in DID mode incl
udes immediate, delay dial, and wink start. It support
s up to eight
ports in DID mode, both expansion slots combined (with ei
ght DIDs on EVM baseboard, up to 16 DIDs maximum).
Additionally, it supports robust front end protection. -
Hello
I'm looking to upgrade a Cisco 2921 system to add additional BRI lines.
The base system is a C2921-CME-SRST/K9 bundel (that has a PVDM3-32)
The existing HWIC slots contain two VIC2-2BRI-NT/TE modules, and one VIC3-4FXS/DID module.
(That's two 2-port BRI modules, and one 4port voice/fax module)
Currently, there are 3 BRI lines coming in, and 2nd port on second module is shutdown (according to cisco specs).
What should I be looking at if we want to add 3 more lines and incorporate conferencing? (as there are issues with conferencing now - possibly due to DSP availability?)
Can we add more modules? Should we replace the 2 port BRI modules with 4 port ones? Do we need to add more PVDMs?
Thanks in advance.Beware the four port BRI modules (HWIC-4B-S/T) as they only support data and not voice.
There is a module which may be of use at the URL below:
http://www.cisco.com/en/US/partner/prod/collateral/modules/ps3115/product_data_sheet0900aecd8016c1c6_ps5855_Products_Data_Sheet.html
The basic module (EVM-HD-8FXS/DID) provides 8 FXS/DID ports and it can accomodate two expansion cards. There is a four port BRI expansion module available (EM-4BRI-NT/TE) so this card could potentially give you 8 x FXS/DID and 8 x ISDN BRI.
It was originally designed for the 2800 routers and needs an adapter (SM-NM-ADPTR) for use in the 2900 series. It is also old so may be due an End of Sale notice soon.
The card does not provide any DSP resources so you may need to add extra PVDM3 resources to your 2900.
As mentioned by Jonathan I would have a think before commiting to lots of BRI circuits. PRI or SIP is likely to be more cost effective in the longer term. -
Hello,
I have a 2821 with a EVM-8FXS/DID installed on EVM slot with a blackbox panel, i have also conected a analog phone on port 7 (voice port 2/0/7) that is working fine, i also have conected a phone in por 0,1,2,3,4,5 but the phone does not work, i tryed to swith the phones but the problem seems to be related with port's 0,1,2,3,4,5.
With show voice port summary I can see tha the port goes off-hook
Can someone help meWhat is the P/N for for blackbox patch panel you are using?
-
Oracle 10gR2 RAC EE 10.2.0.5 problem with one node.
Hi, I have an Oracle Rac 10gR2 10.2.0.5 EE on SLES 10 on ibm ppc. My problem is that in crs don't appear that database is start in one instance. However the database is start when I use srvctl or sqlplus
crsctl query crs softwareversion
CRS active version on the cluster is [10.2.0.5.0]
crsctl query crs activeversion
CRS active version on the cluster is [10.2.0.5.0]
oracle@agripa:/u01/oracle/app/product/102_64/crs/bin> ./srvctl config database
ELIO3
oracle@agripa:/u01/oracle/app/product/102_64/crs/bin> ./srvctl status database -d ELIO3
La instancia ELIO32 se está ejecutando en el nodo julia
La instancia ELIO31 no se está ejecutando en el nodo agripa
agripa:/u01/oracle/app/product/102_64/crs/bin # ./crs_stat -t
Nombre Tipo Destino Estado Host
ora....31.inst application ONLINE OFFLINE
ora....32.inst application ONLINE ONLINE julia
ora.ELIO3.db application ONLINE ONLINE julia
ora....PA.lsnr application ONLINE OFFLINE
ora....PA.lsnr application ONLINE OFFLINE
ora.agripa.gsd application ONLINE OFFLINE
ora.agripa.ons application ONLINE OFFLINE
ora.agripa.vip application ONLINE ONLINE agripa
ora....IA.lsnr application ONLINE ONLINE julia
ora.julia.gsd application ONLINE ONLINE julia
ora.julia.ons application ONLINE ONLINE julia
ora.julia.vip application ONLINE ONLINE julia
oracle@agripa:/u01/oracle/app/product/102_64/app/bin> ./srvctl start instance -d ELIO3 -i ELIO31
PRKP-1001 : Error al iniciar la instancia ELIO31 en el nodo agripaThis command show an error, however the database is up.
oracle@agripa:/u01/oracle/app/product/102_64/app/bin> sqlplus / as sysdba
SQL*Plus: Release 10.2.0.5.0 - Production on Mié Sep 26 09:32:25 2012
Copyright (c) 1982, 2010, Oracle. All Rights Reserved.
Conectado a:
Oracle Database 10g Enterprise Edition Release 10.2.0.5.0 - Production
With the Partitioning, Real Application Clusters, OLAP, Data Mining
and Real Application Testing options
SQL> select * from v$active_instances;
INST_NUMBER INST_NAME
2 julia:ELIO32
4 agripa:ELIO31
SQL>But crs, don't show it.
agripa:/u01/oracle/app/product/102_64/crs/bin # ./crs_stat -t
Nombre Tipo Destino Estado Host
ora....31.inst application ONLINE OFFLINE
ora....32.inst application ONLINE ONLINE julia
ora.ELIO3.db application ONLINE ONLINE julia
ora....PA.lsnr application ONLINE OFFLINE
ora....PA.lsnr application ONLINE OFFLINE
ora.agripa.gsd application ONLINE OFFLINE
ora.agripa.ons application ONLINE OFFLINE
ora.agripa.vip application ONLINE ONLINE agripa
ora....IA.lsnr application ONLINE ONLINE julia
ora.julia.gsd application ONLINE ONLINE julia
ora.julia.ons application ONLINE ONLINE julia
ora.julia.vip application ONLINE ONLINE juliaSome logs...
oracle@agripa:/u01/oracle/app/product/102_64/app/log/agripa/racg> cat ora.ELIO3.ELIO31.inst.log
2012-09-26 09:35:45.108: [ COMMCRS][53473856]clsc_connect: (0x40002a0a6c0) no listener at (ADDRESS=(PROTOCOL=ipc)(KEY=ora_crsqs))
2012-09-26 09:36:15.150: [ RACG][173648] [2346][173648][ora.ELIO3.ELIO31.inst]: end for resource = ora.ELIO3.ELIO31.inst, action = rundetach, status = -1, time = 300.600s
agripa:/u01/oracle/app/product/102_64/crs/bin # ls -ltrach /var/tmp/.oracle/
total 512
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 08:28 sagripaDBG_CSSD
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 08:28 sOracle_CSS_LclLstnr_crs_3
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 08:28 sOCSSD_LL_agripa_crs
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 08:28 sagripaDBG_EVMD
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 08:28 sCagripa_crs_evm
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 08:28 sAagripa_crs_evm
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 09:46 s#3633.2
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 09:46 s#3633.1
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 10:00 s#11308.1
srwxrwxrwx 1 oracle oinstall 0 2012-09-24 10:03 s#11308.2
drwxrwxrwt 8 root root 232 2012-09-26 09:24 ..
srwxrwxrwx 1 oracle oinstall 0 2012-09-26 09:30 sora_racg_ELIO3_agripa
srwxrwxrwx 1 oracle oinstall 0 2012-09-26 09:35 sSYSTEM.evm.acceptor.auth
srwxrwxrwx 1 root root 0 2012-09-26 09:35 sagripaDBG_CRSD
srwxrwxrwx 1 root root 0 2012-09-26 09:40 sCRSD_UI_SOCKET
srwxrwxrwx 1 root root 0 2012-09-26 09:45 sora_crsqs
srwxrwxrwx 1 root root 0 2012-09-26 09:45 sprocr_local_conn_0_PROC
srwxrwxrwx 1 oracle oinstall 0 2012-09-26 09:45 sOCSSD_LL_agripa_
drwxrwxrwt 2 root root 640 2012-09-26 09:45 .
oracle@agripa:/u01/oracle/app/product/102_64/app/log/agripa/racg> cat imon_ELIO3.log
2012-09-26 09:30:41.047: [ RACG][173648] [1100][173648][ora.ELIO3.ELIO31.inst]: racgimon started
2012-09-26 09:31:06.174: [ RACG][70660672] [1100][70660672][ora.ELIO3.ELIO31.inst]:
SQL*Plus: Release 10.2.0.5.0 - Production on Wed Sep 26 09:30:42 2012
Copyright (c) 1982, 2010, Oracle. All Rights Reserved.
Enter user-name: Connected to an idle instance.
SQL> ORACLE instance started.
Total System Global Area 8589934592 bytes
2012-09-26 09:31:06.174: [ RACG][70660672] [1100][70660672][ora.ELIO3.ELIO31.inst]: Fixed Size 2109992 bytes
Variable Size 1358958040 bytes
Database Buffers 7214202880 bytes
Redo Buffers 14663680 bytes
Base de datos montada.
Base de datos abierta.
2012-09-26 09:31:06.174: [ RACG][70660672] [1100][70660672][ora.ELIO3.ELIO31.inst]: SQL> Desconectado de Oracle Database 10g Enterprise Edition Release 10.2.0.5.0 - Production
With the Partitioning, Real Application Clusters, OLAP, Data Mining
and Real Application Testing options
2012-09-26 09:31:06.404: [ RACG][70660672] [1100][70660672][ora.ELIO3.ELIO31.inst]: clsrcexecut: env _USR_ORA_PFILE=/u01/oracle/app/product/102_64/crs/racg/tmp/ora.ELIO3.ELIO31.inst.ora
2012-09-26 09:31:06.404: [ RACG][70660672] [1100][70660672][ora.ELIO3.ELIO31.inst]: clsrcexecut: cmd = /u01/oracle/app/product/102_64/app/bin/racgeut -e _USR_ORA_DEBUG=0 -e ORACLE_SID=ELIO31 540 /u01/oracle/app/product/102_64/app/bin/racgmdb -q
2012-09-26 09:31:06.404: [ RACG][70660672] [1100][70660672][ora.ELIO3.ELIO31.inst]: clsrcexecut: rc = 3, time = 0.230s
2012-09-26 09:31:07.196: [ OCRMSG][70660672]prom_rpc: CLSC send failure..ret code 11
2012-09-26 09:31:07.196: [ OCRMSG][70660672]prom_rpc: possible OCR retry scenario
2012-09-26 09:31:07.254: [ OCRAPI][70660672]procr_open: Node Failure. Attempting retry #0
2012-09-26 09:31:07.528: [ OCRCLI][70660672]oac_reconnect_server: Could not connect to server. clsc ret 9
2012-09-26 09:31:07.584: [ OCRAPI][70660672]procr_open: Node Failure. Attempting retry #1
2012-09-26 09:31:07.847: [ OCRCLI][70660672]oac_reconnect_server: Could not connect to server. clsc ret 9
2012-09-26 09:31:07.904: [ OCRAPI][70660672]procr_open: Node Failure. Attempting retry #2
2012-09-26 09:31:08.178: [ OCRCLI][70660672]oac_reconnect_server: Could not connect to server. clsc ret 9
2012-09-26 09:31:08.235: [ OCRAPI][70660672]procr_open: Node Failure. Attempting retry #3
2012-09-26 09:31:08.488: [ OCRCLI][70660672]oac_reconnect_server: Could not connect to server. clsc ret 9
2012-09-26 09:31:08.544: [ OCRAPI][70660672]procr_open: Node Failure. Attempting retry #4
2012-09-26 09:31:08.808: [ OCRCLI][70660672]oac_reconnect_server: Could not connect to server. clsc ret 9
2012-09-26 09:31:08.865: [ OCRAPI][70660672]procr_open: Node Failure. Attempting retry #5
2012-09-26 09:31:08.971: [ RACG][70660672] [1100][70660672][ora.ELIO3.ELIO31.inst]: clsrcsetenvvar: set env var 'ORACLE_CONFIG_HOME' to be '/u01/oracle/app/product/102_64/crs/'
2012-09-26 09:31:09.767: [ RACG][70660672] [1100][70660672][ora.ELIO3.ELIO31.inst]: clsrcqryapi: crs_qstat error
2012-09-26 09:36:14.709: [ OCRMSG][148804160]prom_rpc: CLSC send failure..ret code 11
2012-09-26 09:36:14.709: [ OCRMSG][148804160]prom_rpc: possible OCR retry scenario
2012-09-26 09:36:14.768: [ OCRAPI][148804160]procr_open: Node Failure. Attempting retry #0
agripa:/u01/oracle/app/product/102_64/crs/bin # ./crs_getperm ora.ELIO3.ELIO32.inst
Nombre: ora.ELIO3.ELIO32.inst
owner:oracle:rwx,pgrp:oinstall:rwx,other::r--,
agripa:/u01/oracle/app/product/102_64/crs/bin # ./crs_getperm ora.ELIO3.ELIO31.inst
Nombre: ora.ELIO3.ELIO31.inst
owner:oracle:rwx,pgrp:oinstall:rwx,other::r--,I try to stop instance with srvctl but instance don't stop.
oracle@agripa:/u01/oracle/app/product/102_64/app/bin> ./srvctl stop instance -d ELIO3 -i ELIO31
oracle@agripa:/u01/oracle/app/product/102_64/app/bin> sqlplus / as sysdba
SQL*Plus: Release 10.2.0.5.0 - Production on Mié Sep 26 09:42:24 2012
Copyright (c) 1982, 2010, Oracle. All Rights Reserved.
Conectado a:
Oracle Database 10g Enterprise Edition Release 10.2.0.5.0 - Production
With the Partitioning, Real Application Clusters, OLAP, Data Mining
and Real Application Testing options
SQL>How can I fix it?
How can I do to srvctl works fine and crs show that database is start??
Thanks you very much!!!My database in another node (julia) was started with sqlplus
sqlplus / as sysdba
startup open;The crsd.log appears the follow
2012-09-24 11:36:56.798: [ CRSMAIN][174064]0CRS Daemon Started.
2012-09-24 11:36:56.798: [ CRSMAIN][363782720]0Starting runCommandServer for (UI = 1, E2E = 0). 0
2012-09-24 11:36:56.798: [ CRSMAIN][365879872]0Starting runCommandServer for (UI = 1, E2E = 0). 1
2012-09-26 09:30:40.776: [ CRSRES][380703296]0startRunnable: setting CLI values
2012-09-26 09:30:40.814: [ CRSRES][380703296]0Attempting to start `ora.ELIO3.ELIO31.inst` on member `agripa`
2012-09-26 09:30:54.931: [ default][174064][ENTER]0
Oracle Database 10g CRS Release 10.2.0.5.0 Production Copyright 1996, 2004, Oracle. All rights reserved
2012-09-26 09:30:54.931: [ default][174064]0CRS Daemon Starting
2012-09-26 09:30:54.932: [ CRSMAIN][174064]0Checking the OCR device
2012-09-26 09:30:54.935: [ CRSMAIN][174064]0Connecting to the CSS Daemon
2012-09-26 09:30:55.238: [ CLSVER][174064]0Active Version from OCR:10.2.0.5.0
2012-09-26 09:30:55.238: [ CLSVER][174064]0Active Version and Software Version are same
2012-09-26 09:30:55.238: [ CRSMAIN][174064]0Initializing OCR
2012-09-26 09:30:55.254: [ OCRRAW][174064]proprioo: for disk 0 (/u01/oracle/1020_64/voting1/ocr), id match (1), my id set (1616921495,1352295226) total id sets (1), 1st set (1616921495,1352295226), 2nd set (0,0) my votes (1), total votes (2)
2012-09-26 09:30:55.254: [ OCRRAW][174064]proprioo: for disk 1 (/u01/oracle/1020_64/voting2/ocr), id match (1), my id set (1616921495,1352295226) total id sets (1), 1st set (1616921495,1352295226), 2nd set (0,0) my votes (1), total votes (2)
2012-09-26 09:30:55.286: [ CRSD][174064]0ENV Logging level for Module: allcomp 0
2012-09-26 09:30:55.289: [ CRSD][174064]0ENV Logging level for Module: default 0
2012-09-26 09:30:55.292: [ CRSD][174064]0ENV Logging level for Module: COMMCRS 0
2012-09-26 09:30:55.294: [ CRSD][174064]0ENV Logging level for Module: COMMNS 0
2012-09-26 09:30:55.297: [ CRSD][174064]0ENV Logging level for Module: CRSUI 0
2012-09-26 09:30:55.300: [ CRSD][174064]0ENV Logging level for Module: CRSCOMM 0
2012-09-26 09:30:55.303: [ CRSD][174064]0ENV Logging level for Module: CRSRTI 0
2012-09-26 09:30:55.306: [ CRSD][174064]0ENV Logging level for Module: CRSMAIN 0
2012-09-26 09:30:55.309: [ CRSD][174064]0ENV Logging level for Module: CRSPLACE 0
2012-09-26 09:30:55.312: [ CRSD][174064]0ENV Logging level for Module: CRSAPP 0
2012-09-26 09:30:55.315: [ CRSD][174064]0ENV Logging level for Module: CRSRES 0
2012-09-26 09:30:55.317: [ CRSD][174064]0ENV Logging level for Module: CRSOCR 0
2012-09-26 09:30:55.320: [ CRSD][174064]0ENV Logging level for Module: CRSTIMER 0
2012-09-26 09:30:55.323: [ CRSD][174064]0ENV Logging level for Module: CRSEVT 0
2012-09-26 09:30:55.326: [ CRSD][174064]0ENV Logging level for Module: CRSD 0
2012-09-26 09:30:55.329: [ CRSD][174064]0ENV Logging level for Module: CLUCLS 0
2012-09-26 09:30:55.332: [ CRSD][174064]0ENV Logging level for Module: CLSVER 0
2012-09-26 09:30:55.335: [ CRSD][174064]0ENV Logging level for Module: OCRRAW 0
2012-09-26 09:30:55.338: [ CRSD][174064]0ENV Logging level for Module: OCROSD 0
2012-09-26 09:30:55.341: [ CRSD][174064]0ENV Logging level for Module: CSSCLNT 0
2012-09-26 09:30:55.343: [ CRSD][174064]0ENV Logging level for Module: OCRAPI 0
2012-09-26 09:30:55.346: [ CRSD][174064]0ENV Logging level for Module: OCRUTL 0
2012-09-26 09:30:55.349: [ CRSD][174064]0ENV Logging level for Module: OCRMSG 0
2012-09-26 09:30:55.352: [ CRSD][174064]0ENV Logging level for Module: OCRCLI 0
2012-09-26 09:30:55.355: [ CRSD][174064]0ENV Logging level for Module: OCRCAC 0
2012-09-26 09:30:55.358: [ CRSD][174064]0ENV Logging level for Module: OCRSRV 0
2012-09-26 09:30:55.360: [ CRSD][174064]0ENV Logging level for Module: OCRMAS 0
2012-09-26 09:30:55.360: [ CRSMAIN][174064]0Filename is /u01/oracle/app/product/102_64/crs/crs/init/agripa.pid
[ clsdmt][299713088]Listening to (ADDRESS=(PROTOCOL=ipc)(KEY=agripaDBG_CRSD))
2012-09-26 09:30:55.383: [ CRSMAIN][174064]0Using Authorizer location: /u01/oracle/app/product/102_64/crs/crs/auth/
2012-09-26 09:30:55.401: [ CRSMAIN][174064]0Initializing RTI
2012-09-26 09:30:55.436: [CRSTIMER][316899904]0Timer Thread Starting.
2012-09-26 09:30:55.438: [ CRSRES][174064]0Parameter SECURITY = 1, running in USER Mode
2012-09-26 09:30:55.438: [ CRSMAIN][174064]0Initializing EVMMgr
2012-09-26 09:30:55.526: [ CRSMAIN][174064]0CRSD locked during state recovery, please wait.
2012-09-26 09:30:56.003: [ CRSRES][174064]0ora.agripa.vip check shows ONLINE
2012-09-26 09:30:56.121: [ CRSMAIN][174064]0CRSD recovered, unlocked.
2012-09-26 09:30:56.122: [ CRSMAIN][174064]0QS socket on: (ADDRESS=(PROTOCOL=ipc)(KEY=ora_crsqs))
2012-09-26 09:30:56.122: [ CRSMAIN][174064]0QS socket on: (ADDRESS=(PROTOCOL=ipc)(KEY=ora_crsqs))
2012-09-26 09:30:56.130: [ CRSMAIN][174064]0CRSD UI socket on: (ADDRESS=(PROTOCOL=ipc)(KEY=CRSD_UI_SOCKET))
2012-09-26 09:30:56.133: [ CRSMAIN][174064]0E2E socket on: (ADDRESS=(PROTOCOL=tcp)(HOST=agripa-priv)(PORT=49896))
2012-09-26 09:30:56.133: [ CRSMAIN][174064]0Starting Threads
2012-09-26 09:30:56.134: [ CRSMAIN][174064]0CRS Daemon Started.
2012-09-26 09:30:56.134: [ CRSMAIN][362721856]0Starting runCommandServer for (UI = 1, E2E = 0). 0
2012-09-26 09:30:56.134: [ CRSMAIN][364819008]0Starting runCommandServer for (UI = 1, E2E = 0). 1
2012-09-26 09:31:08.582: [ default][174064][ENTER]0
Oracle Database 10g CRS Release 10.2.0.5.0 Production Copyright 1996, 2004, Oracle. All rights reserved
2012-09-26 09:31:08.582: [ default][174064]0CRS Daemon Starting
2012-09-26 09:31:08.583: [ CRSMAIN][174064]0Checking the OCR device
2012-09-26 09:31:08.585: [ CRSMAIN][174064]0Connecting to the CSS Daemon
2012-09-26 09:31:08.885: [ CLSVER][174064]0Active Version from OCR:10.2.0.5.0
2012-09-26 09:31:08.885: [ CLSVER][174064]0Active Version and Software Version are same
2012-09-26 09:31:08.885: [ CRSMAIN][174064]0Initializing OCR
2012-09-26 09:31:08.891: [ OCRRAW][174064]proprioo: for disk 0 (/u01/oracle/1020_64/voting1/ocr), id match (1), my id set (1616921495,1352295226) total id sets (1), 1st set (1616921495,1352295226), 2nd set (0,0) my votes (1), total votes (2)
2012-09-26 09:31:08.891: [ OCRRAW][174064]proprioo: for disk 1 (/u01/oracle/1020_64/voting2/ocr), id match (1), my id set (1616921495,1352295226) total id sets (1), 1st set (1616921495,1352295226), 2nd set (0,0) my votes (1), total votes (2)
2012-09-26 09:31:08.934: [ CRSD][174064]0ENV Logging level for Module: allcomp 0
2012-09-26 09:31:08.937: [ CRSD][174064]0ENV Logging level for Module: default 0
2012-09-26 09:31:08.940: [ CRSD][174064]0ENV Logging level for Module: COMMCRS 0
2012-09-26 09:31:08.942: [ CRSD][174064]0ENV Logging level for Module: COMMNS 0
2012-09-26 09:31:08.945: [ CRSD][174064]0ENV Logging level for Module: CRSUI 0
2012-09-26 09:31:08.948: [ CRSD][174064]0ENV Logging level for Module: CRSCOMM 0
2012-09-26 09:31:08.964: [ CRSD][174064]0ENV Logging level for Module: CRSRTI 0
2012-09-26 09:31:08.970: [ CRSD][174064]0ENV Logging level for Module: CRSMAIN 0
2012-09-26 09:31:08.973: [ CRSD][174064]0ENV Logging level for Module: CRSPLACE 0
2012-09-26 09:31:08.976: [ CRSD][174064]0ENV Logging level for Module: CRSAPP 0
2012-09-26 09:31:08.979: [ CRSD][174064]0ENV Logging level for Module: CRSRES 0
2012-09-26 09:31:08.982: [ CRSD][174064]0ENV Logging level for Module: CRSOCR 0
2012-09-26 09:31:08.985: [ CRSD][174064]0ENV Logging level for Module: CRSTIMER 0
2012-09-26 09:31:08.988: [ CRSD][174064]0ENV Logging level for Module: CRSEVT 0
2012-09-26 09:31:08.991: [ CRSD][174064]0ENV Logging level for Module: CRSD 0
2012-09-26 09:31:08.994: [ CRSD][174064]0ENV Logging level for Module: CLUCLS 0
2012-09-26 09:31:08.997: [ CRSD][174064]0ENV Logging level for Module: CLSVER 0
2012-09-26 09:31:08.999: [ CRSD][174064]0ENV Logging level for Module: OCRRAW 0
2012-09-26 09:31:09.002: [ CRSD][174064]0ENV Logging level for Module: OCROSD 0
2012-09-26 09:31:09.005: [ CRSD][174064]0ENV Logging level for Module: CSSCLNT 0
2012-09-26 09:31:09.008: [ CRSD][174064]0ENV Logging level for Module: OCRAPI 0
2012-09-26 09:31:09.011: [ CRSD][174064]0ENV Logging level for Module: OCRUTL 0
2012-09-26 09:31:09.014: [ CRSD][174064]0ENV Logging level for Module: OCRMSG 0
2012-09-26 09:31:09.017: [ CRSD][174064]0ENV Logging level for Module: OCRCLI 0
2012-09-26 09:31:09.020: [ CRSD][174064]0ENV Logging level for Module: OCRCAC 0
2012-09-26 09:31:09.023: [ CRSD][174064]0ENV Logging level for Module: OCRSRV 0
2012-09-26 09:31:09.026: [ CRSD][174064]0ENV Logging level for Module: OCRMAS 0
2012-09-26 09:31:09.026: [ CRSMAIN][174064]0Filename is /u01/oracle/app/product/102_64/crs/crs/init/agripa.pid
[ clsdmt][303034944]Listening to (ADDRESS=(PROTOCOL=ipc)(KEY=agripaDBG_CRSD))
2012-09-26 09:31:09.057: [ CRSMAIN][174064]0Using Authorizer location: /u01/oracle/app/product/102_64/crs/crs/auth/
2012-09-26 09:31:09.072: [ CRSMAIN][174064]0Initializing RTI
2012-09-26 09:31:09.094: [CRSTIMER][319812160]0Timer Thread Starting.
2012-09-26 09:31:09.096: [ CRSRES][174064]0Parameter SECURITY = 1, running in USER Mode
2012-09-26 09:31:09.096: [ CRSMAIN][174064]0Initializing EVMMgr
2012-09-26 09:31:09.198: [ CRSMAIN][174064]0CRSD locked during state recovery, please wait.
2012-09-26 09:31:09.728: [ CRSRES][174064]0ora.agripa.vip check shows ONLINE
2012-09-26 09:31:09.846: [ CRSMAIN][174064]0CRSD recovered, unlocked.
2012-09-26 09:31:09.847: [ CRSMAIN][174064]0QS socket on: (ADDRESS=(PROTOCOL=ipc)(KEY=ora_crsqs))
2012-09-26 09:31:09.847: [ CRSMAIN][174064]0QS socket on: (ADDRESS=(PROTOCOL=ipc)(KEY=ora_crsqs))
2012-09-26 09:31:09.855: [ CRSMAIN][174064]0CRSD UI socket on: (ADDRESS=(PROTOCOL=ipc)(KEY=CRSD_UI_SOCKET))
2012-09-26 09:31:09.858: [ CRSMAIN][174064]0E2E socket on: (ADDRESS=(PROTOCOL=tcp)(HOST=agripa-priv)(PORT=49896))
2012-09-26 09:31:09.859: [ CRSMAIN][174064]0Starting Threads
2012-09-26 09:31:09.859: [ CRSMAIN][174064]0CRS Daemon Started.
2012-09-26 09:31:09.859: [ CRSMAIN][364917312]0Starting runCommandServer for (UI = 1, E2E = 0). 0
2012-09-26 09:31:09.859: [ CRSMAIN][367014464]0Starting runCommandServer for (UI = 1, E2E = 0). 1
2012-09-26 09:35:44.874: [ default][174064][ENTER]0
Oracle Database 10g CRS Release 10.2.0.5.0 Production Copyright 1996, 2004, Oracle. All rights reserved
2012-09-26 09:35:44.874: [ default][174064]0CRS Daemon Starting
2012-09-26 09:35:44.875: [ CRSMAIN][174064]0Checking the OCR device
2012-09-26 09:35:44.877: [ CRSMAIN][174064]0Connecting to the CSS Daemon
2012-09-26 09:35:45.186: [ CLSVER][174064]0Active Version from OCR:10.2.0.5.0
2012-09-26 09:35:45.186: [ CLSVER][174064]0Active Version and Software Version are same
2012-09-26 09:35:45.186: [ CRSMAIN][174064]0Initializing OCR
2012-09-26 09:35:45.201: [ OCRRAW][174064]proprioo: for disk 0 (/u01/oracle/1020_64/voting1/ocr), id match (1), my id set (1616921495,1352295226) total id sets (1), 1st set (1616921495,1352295226), 2nd set (0,0) my votes (1), total votes (2)
2012-09-26 09:35:45.202: [ OCRRAW][174064]proprioo: for disk 1 (/u01/oracle/1020_64/voting2/ocr), id match (1), my id set (1616921495,1352295226) total id sets (1), 1st set (1616921495,1352295226), 2nd set (0,0) my votes (1), total votes (2)
2012-09-26 09:35:45.236: [ CRSD][174064]0ENV Logging level for Module: allcomp 0
2012-09-26 09:35:45.242: [ CRSD][174064]0ENV Logging level for Module: default 0
2012-09-26 09:35:45.245: [ CRSD][174064]0ENV Logging level for Module: COMMCRS 0
2012-09-26 09:35:45.247: [ CRSD][174064]0ENV Logging level for Module: COMMNS 0
2012-09-26 09:35:45.250: [ CRSD][174064]0ENV Logging level for Module: CRSUI 0
2012-09-26 09:35:45.253: [ CRSD][174064]0ENV Logging level for Module: CRSCOMM 0
2012-09-26 09:35:45.256: [ CRSD][174064]0ENV Logging level for Module: CRSRTI 0
2012-09-26 09:35:45.259: [ CRSD][174064]0ENV Logging level for Module: CRSMAIN 0
2012-09-26 09:35:45.262: [ CRSD][174064]0ENV Logging level for Module: CRSPLACE 0
2012-09-26 09:35:45.265: [ CRSD][174064]0ENV Logging level for Module: CRSAPP 0
2012-09-26 09:35:45.269: [ CRSD][174064]0ENV Logging level for Module: CRSRES 0
2012-09-26 09:35:45.273: [ CRSD][174064]0ENV Logging level for Module: CRSOCR 0
2012-09-26 09:35:45.276: [ CRSD][174064]0ENV Logging level for Module: CRSTIMER 0
2012-09-26 09:35:45.279: [ CRSD][174064]0ENV Logging level for Module: CRSEVT 0
2012-09-26 09:35:45.282: [ CRSD][174064]0ENV Logging level for Module: CRSD 0
2012-09-26 09:35:45.285: [ CRSD][174064]0ENV Logging level for Module: CLUCLS 0
2012-09-26 09:35:45.288: [ CRSD][174064]0ENV Logging level for Module: CLSVER 0
2012-09-26 09:35:45.291: [ CRSD][174064]0ENV Logging level for Module: OCRRAW 0
2012-09-26 09:35:45.293: [ CRSD][174064]0ENV Logging level for Module: OCROSD 0
2012-09-26 09:35:45.297: [ CRSD][174064]0ENV Logging level for Module: CSSCLNT 0
2012-09-26 09:35:45.300: [ CRSD][174064]0ENV Logging level for Module: OCRAPI 0
2012-09-26 09:35:45.302: [ CRSD][174064]0ENV Logging level for Module: OCRUTL 0
2012-09-26 09:35:45.305: [ CRSD][174064]0ENV Logging level for Module: OCRMSG 0
2012-09-26 09:35:45.308: [ CRSD][174064]0ENV Logging level for Module: OCRCLI 0
2012-09-26 09:35:45.311: [ CRSD][174064]0ENV Logging level for Module: OCRCAC 0
2012-09-26 09:35:45.314: [ CRSD][174064]0ENV Logging level for Module: OCRSRV 0
2012-09-26 09:35:45.318: [ CRSD][174064]0ENV Logging level for Module: OCRMAS 0
2012-09-26 09:35:45.318: [ CRSMAIN][174064]0Filename is /u01/oracle/app/product/102_64/crs/crs/init/agripa.pid
[ clsdmt][303034944]Listening to (ADDRESS=(PROTOCOL=ipc)(KEY=agripaDBG_CRSD))
2012-09-26 09:35:45.341: [ CRSMAIN][174064]0Using Authorizer location: /u01/oracle/app/product/102_64/crs/crs/auth/
2012-09-26 09:35:45.361: [ CRSMAIN][174064]0Initializing RTI
2012-09-26 09:35:45.391: [CRSTIMER][319812160]0Timer Thread Starting.
2012-09-26 09:35:45.393: [ CRSRES][174064]0Parameter SECURITY = 1, running in USER Mode
2012-09-26 09:35:45.393: [ CRSMAIN][174064]0Initializing EVMMgr
2012-09-26 09:35:45.481: [ CRSMAIN][174064]0CRSD locked during state recovery, please wait.
2012-09-26 09:35:45.956: [ CRSRES][174064]0ora.agripa.vip check shows ONLINE
2012-09-26 09:35:46.097: [ CRSMAIN][174064]0CRSD recovered, unlocked.
2012-09-26 09:35:46.098: [ CRSMAIN][174064]0QS socket on: (ADDRESS=(PROTOCOL=ipc)(KEY=ora_crsqs))
2012-09-26 09:35:46.098: [ CRSMAIN][174064]0QS socket on: (ADDRESS=(PROTOCOL=ipc)(KEY=ora_crsqs))
2012-09-26 09:35:46.105: [ CRSMAIN][174064]0CRSD UI socket on: (ADDRESS=(PROTOCOL=ipc)(KEY=CRSD_UI_SOCKET))
2012-09-26 09:35:46.109: [ CRSMAIN][174064]0E2E socket on: (ADDRESS=(PROTOCOL=tcp)(HOST=agripa-priv)(PORT=49896))
2012-09-26 09:35:46.109: [ CRSMAIN][174064]0Starting Threads
2012-09-26 09:35:46.109: [ CRSMAIN][174064]0CRS Daemon Started.
2012-09-26 09:35:46.109: [ CRSMAIN][364896832]0Starting runCommandServer for (UI = 1, E2E = 0). 0
2012-09-26 09:35:46.109: [ CRSMAIN][366993984]0Starting runCommandServer for (UI = 1, E2E = 0). 1
2012-09-26 09:36:09.889: [ CRSRES][381674048]0CRS-1002: Resource 'ora.ELIO3.db' is already running on member 'julia'
2012-09-26 09:47:41.288: [ CRSRES][379576896]0ora.ELIO3.ELIO31.inst target set to OFFLINE before stop action
2012-09-26 09:47:41.288: [ CRSRES][379576896]0StopResource: setting CLI values
2012-09-26 09:47:41.355: [ CRSRES][379576896]0Target set to OFFLINE for `ora.ELIO3.ELIO31.inst`
2012-09-26 09:47:42.266: [ CRSRES][379576896]0`ora.ELIO3.ELIO31.inst` is already OFFLINE.
2012-09-26 09:47:43.278: [ CRSRES][379576896]0`ora.ELIO3.ELIO31.inst` is already OFFLINE.
2012-09-26 09:47:44.286: [ CRSRES][379576896]0`ora.ELIO3.ELIO31.inst` is already OFFLINE.
2012-09-26 09:47:45.298: [ CRSRES][379576896]0`ora.ELIO3.ELIO31.inst` is already OFFLINE.PD: Excuseme for the long text about crsd.log, but I don't know how can I attach a file.
Thanks you very much!!.
Maybe you are looking for
-
Unable to be discoverable for bluetooth
I have a bb bold model 9900. I am attempting to connect to a bluetooth device in a car. On my phone, after turning Bluetooth on, I advanced to Networks and Connections. Under the Bluetooth heading I tried to set my phone to discoverable The men
-
I have the first part of a song on my iphone, the second part of the same song shows up in my "purchased" list in itunes store. It used to play the whole song on my phone, what happened and how can I fix this? thanks.
-
my video ipod battery duration is too short (10 hours) i need a solution to this problem? ipod video 60gb Windows XP Pro
-
Add insurance to phone after it's been used for 2 months
can I add insurance to my phone after it's been used for 2 months....I'm scared that my daughter will lose it or break...thx
-
Creating User-Generated Workspaces | Learn Photoshop CS6 | Adobe TV
Adobe Photoshop boasts tons of panels and features- But do you really need them all open at the same time? Let Infinite Skills author, Andy Anderson show you how to create workspaces that reduce the clutter, and help you get the job done. http://adob