EVM-HD-8FXS/DID as backup

Customer wants 12 pots lines for backup in case the PRI is down. I was thinking of using EVM-HD-8FXS/DID which will give me 8 DIDs and 4 port FXO card or FXO expension module. The question is can I make outbound calls on these lines when configured as DIDs? Is there a better solution?
Chris

You should be able to use DID trunks (as long as telco provision them as DID trunks) and set all the FXS ports to DID mode. You get 8 base FXS ports on the EVM and you can either add 6 FXO cards or add a 3 FXS/4FXO card or another 8 port FXS port daughter card (expansion module). In DID mode, you wont get any dialtone (much like FXO)
I am not sure if DID mode is available on the expansion cards. Also if you mix and match FXS and DID modes you have to take care of impedance settings. Check this link
http://www.cisco.com/en/US/products/hw/modules/ps2617/products_configuration_example09186a0080513001.shtml
HTH
Sankar
---edited----
I dont think you can configure any ports on the EM cards in DID mode. I strongly believe, you are limited to 8 DID ports (base FXS ports)

Similar Messages

EVM-HD-8FXS/DID EXT MODULE

HOW MANY FXS VOICE PORTS GIVE ME THE EVM-HD-8FXS/DID WITHOUT EM-HDA- EXPANSION MODULES?.
THANKS.

OK, IF I NEED 8 FXS PORTS AND 6 FXO PORTS, JUST NEED PURCHASE:
1x EVM-HD-8FXS/DID plus
1x EM-HDA-6FX0.
RIGHT?
Thanks.

Problem whit cisco 2921 + EVM-HD-8FXS/DID whit CUCM

Hello everyone.
I have the following problem that I am not able to resolve. I define a new connection BRI.
I can make calls seamlessly between the Cisco Unified Communications Manager (version: 8.5.1.10000-26) and Cisco 2921 (CISCO2921-V/K9).
But when you receive calls from BRI Cisco receives the call but the Cisco Unified Communications Manager does not tranfere for Ext
And I can not understand why. In other BRI interfaces do not have this problem.
This configuration here that I'm using.
Current configuration : 17238 bytes
! Last configuration change at 18:02:34 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname <<omitted>>
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret 5 <<omitted>>
aaa new-model
aaa authentication login default none
aaa authentication login <<omitted>>
aaa accounting connection h323 start-stop group radius
aaa session-id common
clock timezone PORT 0 0
clock summer-time PORT recurring last Sun Mar 1:00 last Sun Oct 1:00
network-clock-participate slot 1
network-clock-participate wic 0
network-clock-participate wic 1
network-clock-participate wic 2
network-clock-participate wic 3
network-clock-select 1 BRI0/0/0
network-clock-select 2 BRI0/1/0
network-clock-select 3 BRI0/2/0
network-clock-select 4 BRI0/3/0
no ipv6 cef
ip source-route
ip cef
no ip domain lookup
ip domain name <<omitted>>
multilink bundle-name authenticated
isdn switch-type basic-net3
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed- <<omitted>>
enrollment selfsigned
subject-name cn= <<omitted>>
revocation-check none
rsakeypair TP-self-signed- <<omitted>>
crypto pki certificate chain <<omitted>>
<<omitted>>
      quit
voice-card 0
dsp services dspfarm
voice call send-alert
voice call disc-pi-off
voice call carrier capacity active
voice rtp send-recv
voice service voip
no ip address trusted authenticate
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
h323
modem passthrough nse codec g711ulaw
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class h323 1
h225 timeout tcp establish 5
voice translation-rule 1
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 2
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
rule 4 /^21 <<omitted>>/ /21 <<omitted>>/
rule 5 /^21 <<omitted>>/ /21 <<omitted>>/
rule 6 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 3
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 4
rule 1 /^0/ /400/
rule 2 /^/ /21 <<omitted>>/
voice translation-rule 5
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 11
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 12
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /.*/ /21 <<omitted>>/
voice translation-rule 13
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 14
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 15
rule 1 /.*/ /21<<omitted>>/
voice translation-rule 21
rule 1 /^./ /0&/
voice translation-rule 22
rule 1 /^./ /0&/
voice translation-rule 25
rule 1 /^./ /0&/
|
voice translation-rule 23
rule 1 /^./ /0&/
voice translation-rule 24
rule 1 /^./ /0&/
voice translation-rule 32
rule 1 /^212104974/ /21 <<omitted>>/
rule 2 /.*/ /212104975/
voice translation-profile INLINE_EMPA
translate calling 22
translate called 2
voice translation-profile INLINE_EMPB
translate calling 23
translate called 3
voice translation-profile INLINE_EMPC
translate calling 25
translate called 5
voice translation-profile INLINE_EMPE
translate calling 24
translate called 4
voice translation-profile INLINE_EMPD
translate calling 21
translate called 1
voice translation-profile OUTLINE_EMPA
translate calling 12
voice translation-profile OUTLINE_EMPA_NT_FAX
translate calling 32
voice translation-profile OUTLINE_EMPB
translate calling 13
voice translation-profile OUTLINE_EMPC
translate calling 15
voice translation-profile OUTLINE_EMPE
translate calling 14
voice translation-profile OUTLINE_EMPD
translate calling 11
license udi pid CISCO2921/K9 sn <<omitted>>
hw-module pvdm 0/0
hw-module sm 1
username admin privilege 15 password 0 <<omitted>>
redundancy
ip ssh time-out 60
ip ssh authentication-retries 2
class-map match-all Voz
match access-group 100
policy-map QoS
class Voz
priority 200
set precedence 5
class class-default
fair-queue
gw-accounting aaa
attribute acct-session-id overloaded
acct-template callhistory-detail
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address <<omitted>> 255.255.0.0
ip access-group BLOCK in
load-interval 30
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr <<omitted>>
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
interface BRI0/0/0
description EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/0/1
description Ecotel EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/0
description EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation first-call
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/1
description EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/0
description EMPB N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/1
description Ecotel EMPB N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/3/0
description EMPE N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/3/1
description Ecotel EMPA N
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/0
description B EMPC N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI1/1
description Ecotel EMPE N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/2
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/3
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/4
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/5
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/6
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/7
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip rtcp report interval 500
ip access-list extended BLOCK
deny   ip any host <<omitted>>
deny   ip any host <<omitted>>
deny   ip any host <<omitted>>
deny   ip any host <<omitted>>
permit ip any any
ip radius source-interface GigabitEthernet0/0
radius-server host <<omitted>> auth-port 1647
radius-server host <<omitted>> acct-port 1647
radius-server key <<omitted>>
radius-server vsa send accounting
control-plane
voice-port 0/0/0
translation-profile incoming INLINE_EMPD
translation-profile outgoing OUTLINE_EMPD
compand-type a-law
cptone PT
voice-port 0/0/1
compand-type a-law
cptone PT
voice-port 0/1/0
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
voice-port 0/1/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA_NT_FAX
compand-type a-law
cptone PT
voice-port 0/2/0
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
voice-port 0/2/1
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 0/3/0
translation-profile incoming INLINE_EMPE
translation-profile outgoing OUTLINE_EMPE
compand-type a-law
cptone PT
voice-port 0/3/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 1/0/0
compand-type a-law
cptone PT
voice-port 1/0/1
compand-type a-law
cptone PT
voice-port 1/0/2
compand-type a-law
cptone PT
voice-port 1/0/3
compand-type a-law
cptone PT
voice-port 1/0/4
compand-type a-law
cptone PT
voice-port 1/0/5
compand-type a-law
cptone PT
voice-port 1/0/6
compand-type a-law
cptone PT
voice-port 1/0/7
compand-type a-law
cptone PT
voice-port 1/0/8
translation-profile incoming INLINE_EMPC
translation-profile outgoing OUTLINE_EMPC
compand-type a-law
cptone PT
voice-port 1/0/9
compand-type a-law
cptone PT
voice-port 1/0/10
compand-type a-law
cptone PT
voice-port 1/0/11
compand-type a-law
cptone PT
voice-port 1/0/16
compand-type a-law
cptone PT
voice-port 1/0/17
compand-type a-law
cptone PT
voice-port 1/0/18
compand-type a-law
cptone PT
voice-port 1/0/19
compand-type a-law
cptone PT
ccm-manager music-on-hold
no mgcp package-capability res-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp profile default
dial-peer voice 1 pots
description +++++ Dial-peer +++++
incoming called-number .
direct-inward-dial
port 0/0/0
dial-peer voice 10 pots
description touchwise
destination-pattern 1T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 20 pots
description globalmove
preference 1
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 30 pots
description globaltemp
shutdown
destination-pattern 3T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 40 pots
description EMPE
destination-pattern 4T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/3/0
dial-peer voice 100 voip
preference 1
destination-pattern .
session target ipv4:10.35.2.1
voice-class codec 1
no vad
dial-peer voice 21 pots
description globalmove
preference 2
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 101 voip
preference 2
destination-pattern .
session target ipv4:10.35.2.2
voice-class codec 1
no vad
dial-peer voice 24 pots
description globalmove
preference 1
destination-pattern 59[1236].......
port 0/3/1
forward-digits 9
dial-peer voice 25 pots
description globalmove
preference 1
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 26 pots
description globalmove
preference 2
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 27 pots
description globalmove
preference 1
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 28 pots
description globalmove
preference 2
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 34 pots
description globalTemp
preference 1
destination-pattern 39[1236].......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/1
forward-digits 9
dial-peer voice 35 pots
description globalTemp
preference 1
destination-pattern 300T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 37 pots
description globalTemp
preference 1
destination-pattern 3[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 14 pots
description empd
preference 1
destination-pattern 19386648.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 15 pots
description empd
preference 1
destination-pattern 19365483.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 16 pots
description empd
preference 1
destination-pattern 19341347.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 50 pots
description EMPC
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 1/0/8
gateway
timer receive-rtp 1200
gatekeeper
shutdown
call-manager-fallback
max-conferences 4 gain -6
transfer-system full-consult
ip source-address 10.35.2.250 port 2000
max-ephones 100
max-dn 300
transfer-pattern 09........
transfer-pattern 02........
transfer-pattern 0.........
transfer-pattern 000T
transfer-pattern 4...
keepalive 10
time-format 24
date-format dd-mm-yy
shutdown
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
login authentication touchwise
transport input ssh
line vty 5 15
login authentication touchwise
transport input ssh
scheduler allocate 20000 1000
ntp master 5
end

If t i "Translation Pattern Configuration" switch to another "Partition" existing or internal it works.
If change back for the new i create. It does not work.
So I must be some flaw i made in Cisco Unified CM.

EVM-HD-8FXS problem

In router/gateway 3825 I have a EVM-HD-8FXS/DID card and I want it register with CallManager. I have on CallManager "AALN/S1/SU0/[email protected]", Device type "Cisco MGCP FXS Port" Status:"Rejected". Any idea why is it rejected?

check ur Router if it has following commands
ccm-manager mgcp
ccm-manager config server
ccm-manager config
mgcp
mgcp call-agent 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
Verify u have "ccm-manager config"

EVM-8FXS/DID

Hello,
I have a 2821 with a EVM-8FXS/DID installed on EVM slot with a blackbox panel, i have also conected a analog phone on port 7 (voice port 2/0/7) that is working fine, i also have conected a phone in por 0,1,2,3,4,5 but the phone does not work, i tryed to swith the phones but the problem seems to be related with port's 0,1,2,3,4,5.
With show voice port summary I can see tha the port goes off-hook
Can someone help me

What is the P/N for for blackbox patch panel you are using?

I sent my iphone for repair. before I sent it I did a backup (on the 7th of august). no i got my phone back but in iTunes I only see a backup from 21st of july. How can I access my latest back up?

I sent my iPhone to Apple for repair. Before I sent it I did a backup (on the 7th of August). Today I got it back, but my iTunes only shows me a backup from 21st july and from today. How can I access my backup from 7th of august?

You should really read the manual.
"How do you restore from backup? "
Restore. When given the choice, choose to use backup.
"And how can I check to see if the pics and videos are on my computer somewhere first??"
They would only be where you put them. What program did you use to import them? Pics/vids taken with ipod are not part of the sync process at all. You should be importing them just as you would with any digital camera.
If you did not import them, then they are not on your computer.

I did a backup on my iPod touch and it said it worked...but now it won't let me access anything and says "iTunes has detected an iPod in recovery mode. You must restore this IPod before it can be used." I will lose all my videos and pics if I do that

I did a backup on my iPod touch last night and it said it worked...I wanted to make sure my 1100 pictures and videos, mostly of my son, were safe since we rarely use the iPod touch anymore since we bought an iPad...I can't find them or I have no idea how to access them...I do not have a MAC...I have an HP computer with windows...
Now when I try to use my iTunes a message comes up that says my iPod is on recovery mode and has to do a restore to use my iTunes again...so when u click on that it states that pushing that button will restore my iPod touch to its factory settings...which means I will lose all my data...which I CANNOT do bc the videos of my son are some of his first words, first giggles, etc.
Now my iPod is stuck on a screen with a picture of a USB cord and an iTunes icon... and holding the power and push buttons down at the same time does nothing except bring up the apple icon for a moment and then it goes right back to the USB and iTunes icon
When I called Apple they said in order to talk to tech support I had to pay a fee of 19 dollars...which I think is kind of crap...I paid over 300 dollars for this and all I want is somebody to help me access my pics...I have done nothing wrong...this iPod was never dropped and never broke...I did the backup like I was supposed to and now I have an IPod touch that does nothing, and if my library of pics and videos are on my computer, I have no clue where or how to view them or back them up onto DVD....
I'm very upset and frustrated...please help!!!

You should really read the manual.
"How do you restore from backup? "
Restore. When given the choice, choose to use backup.
"And how can I check to see if the pics and videos are on my computer somewhere first??"
They would only be where you put them. What program did you use to import them? Pics/vids taken with ipod are not part of the sync process at all. You should be importing them just as you would with any digital camera.
If you did not import them, then they are not on your computer.

My itunes wont auto sync my iphone 4 after i connect it to itunes. But it can auto sync when i connect it to my old laptop. what's the problem that it can't auto sync and when i did a backup in my new laptop, it was corrupted the next day.

But it can auto sync when i connect it to my old laptop. what's the problem that it can't auto sync and when i did a backup in my new laptop, it was corrupted the next day and i was forced to use back a backup which i did in my old laptop 4 months ago. do i have to reinstall the itunes? will my backups be corrupted after i sync again? pls guide.
P.S/ its the latest version of the itunes whenever i did the backups.

iPod touches or any iDevices from Apple sync only to one computer. If you sync to a different computer, all your music will be replace with the music from the new computer's iTunes. If the music were purchased from iTunes, you can re-download them again otherwise the music on iPod touch will be deleted. Do you have iTunes backup?

I did a backup from my 3G and want to get the backup now on my iPhone 4, but the backup from the old 3G is not shown as an option to configurate. How do I get the information on my new phone?

I did a backup from my 3G and want to get the backup now on my iPhone 4, but the backup from the old 3G is not shown as an option to configurate. How do I get the information on my new phone?

First, back up your old iphone manually:
Disable autosync in iTunes, connect your phone to your new computer and right click on it in the device list and choose backup. iTunes will backup your phone without syncing.
Transfer your purchases the same way, choosing "transfer purchases" this time.
When you connect your old phone for the first time, all media content will be erased. But you can restore your settings and app data from your manual backup afterwards.
Don't forget to set up at least one contact and event on your new computer to be able to merge calendars and contacts when you sync the phone for the first time.
About backups and what's saved: http://support.apple.com/kb/HT1766
How to back up and restore: http://support.apple.com/kb/HT1414
How to download apps for free again:http://support.apple.com/kb/HT2519
After that, connect your new phone and let iTunes set it up. iTunes will detect the old 3G backup and ask you, if you want to use it to restore the info on your new iphone. If you agree, all settings and data will be present after the process is finished.
This is also explained in this article: http://support.apple.com/kb/HT4137

I use an Iphone 4 which had to be replaced recently. However when i did a backup it was on the new IOS version 7, but now that my phone was replaced and i am back on the old IOS version 6 i how do i restore my backup??

I use an Iphone 4 which had to be replaced recently. However when i did a backup it was on the new IOS version 7, but now that my phone was replaced and i am back on the old IOS version 6 i how do i restore my backup??
When i try to restore my Back up using Itunes this is the message i get - "Unable to restore backup as the software is old - Please setup as a new device and then try to restore your backup" - Please advise. If i do so are there any chances of loosing my data. At this point in time i would be happy if i could just retreive my contacts list. Any suggestions would be greatly appreciated.

Nope - you cannot restore a backup from a newer iOS version on to a device running an older iOS version. The reverse works, but in your case to use your backup, you must update to iOS 7.0.3 - no other option if you want to use that backup.

TS4036 my device has been crushed beyond repair, and I don't think I ever did the backup thing. does this mean I can no longer see any of my stuffs??

my device has been crushed beyond repair, and I don't think I ever did the backup thing. does this mean I can no longer see any of my stuffs??

thats really 4kd up

Currently have 30K pics on PC Win. 7 laptop using PSE 8, corrected issues and did full backup on portable hard drive plus saved (Extensive) Keyword tags to file. Installed PSE 13 on PC Win 8.1 laptop. Will attach same portable Hard drive to new laptop.

Currently have 30K pics on PC Win. 7 laptop using PSE 8, corrected issues and did full backup on portable hard drive plus saved (Extensive) Keyword tags to file. Installed PSE 13 on PC Win 8.1 laptop. Will attach same portable Hard drive to new laptop. How do I import prev Keyword Tags from file and Restore catalog from port. HD to new PC and in what order? I have not opened PSE 13 on new PC yet. Would like to do it right the first time!

No importing needed.
See these instructions: Use Backup, Restore to move catalog | Organizer | Elements 6 or later

Hello guys! How do I get my photo back after I restored my iphone5??? Ihave never did any backup or logged in iCloud before. Is it possible for me to get them back??

Hello guys! How do I get my photo back after I restored my iphone5??? Ihave never did any backup or logged in iCloud before. Is it possible for me to get them back?? I use " find my iphone" and accidentally locked my iphone then I have to restore it to unlock it. But then I found out everything is gone after I restore my phone, is there anyway I could get them back??

If you never backed them up, where do you suppose you can restore them from?

I can't remember the password I used when I did a "backup to computer". Does this mean that my only option for backing up my iphone from now on is using the cloud? #I've tried any PW i can recall ever using, I must have gotten creative darn it.#

I did a backup decided to do a full backup with a password. I forgot the password I used (it was a couple of months ago and I must have gotten creative with it.) Without that password the option to back up to my computer is dead, right? My only option for backup will be the cloud. I want to be sure I understand the mess I am in. I have tried the passwords I have used before, I cannot believe I did this

This is asked and answered many, many times each and every day, iincluding several in the past few minutes.
The forum search bar is on the right side of this page as is the More Like This section.
You will find your answer there many times over.
Type "unable to restore" into the search bar at the top of this page by Support and read the resulting help article.

I recently did a backup and restore on my Iphone 4 because I was switching carriers. When i switched carriers i went back to I tunes to restore all that iI backed up I can't get any of my pics back contacts or anything. is there a way to recover the data?

I recently did a backup and restore on my Iphone4 because iI was going to switch carriers. When I switched carriers I went back to I tunes to restore my backup and nothing was there .Some how I lost all of my data, is there a way I can retrive my data or not? I had all of my pics and contacts on the backup. please help..

When you say nothing was there, do you mean the backup wasn't there?

EVM-HD-8FXS/DID as backup

Similar Messages

Maybe you are looking for