Problem with Deskjet 1000

Image that should be one page is printing portions of the image on many pages.

Arrgh.... OK, the "original" Deskjet 1000 was a 13"x19" printer from a dozen or so years ago that used 45 and 41 cartridges. Sorry about that, the Deskjet 1000-J110 does support an ink level gauge. I would suggest clicking on Start, Devices and Printers, right click on the Deskjet 1000, Printer Properties, Ports and make sure the checkbox is checked for "Enable bidirectional support".
BTW, with ink supplies as small as the 61 I would suggest always having a spare on hand :-).
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

Problems with SCXI-1000 after update from Labview 5.1 to LabView 6

I'm using a SCXI-1000 board to readout temperatures from some Pt-100 sensors. The analog signal going into the SCXI-1000 is correct. The reading by LabView program is not. The SCXI-1000 is connected to the PC via a PCI-1200 bus. I've used this setup for some time with LabView 5.1. Here it worked nicely. Recently I upgraded to LabView 6. Now the readout is not giving the proper values. When I reinstalled Labview 5.1 it was all OK again. When using LabView6 do I need to calibrate of configure the SCXI-1000 for my temperature readout? Are there any known problems with upgrading from LabView5 to Labview6? How can I see which analog values are being read by the SCXI-1000 and to which values they are converte
d? Hopefully you can help me.

Upgrading from different versions of LabVIEW shouldn't be a problem; I would suspect different versions of NI-DAQ first. Make sure you use the Measurement and Automation Explorer (MAX) to configure your card.
To see if it's a driver update issue, when you use the LabVIEW 6 installation CD, choose custom install and don't upgrade your drivers. You may have to browse into your LabVIEW 5 directory and use copies of the VIs from there.

Problem with Deskjet D2360

I have an HP Deskjet D2360, every time i print, the paper advances in the center and that status on my computer is paper jam with bliking LED. I've tried all the steps (taking out the paper jam, cleaning the rollers, resetting, and do sample printing) given by HP in trouble shooting but it seems it does not work. Can any body help?
PS. I have a genuine brand new HP cartriges.

It sounds like you have already done most of the steps in this document. At this point the remaining option is Solution 4 - Service the printer.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Problem with DeskJet 1220C

Hi there, I have one of the old HP DeskJet 1220C and I managed to connect to it via USB using a virtual port. The problem is that whenever I print doesn't matter what it is, the printer always prints out a paper with funny symbols and numbers. Please help me...

I have been able to fix the first problem. The problem was, that the safety switch for the top cover seems to have a defect, so it had to be manually reset. An explanation can be found here: http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&cc=us&docname=c01065334&dlc=en&product=467982
Afterwards I found, that the printer was unable to grab paper from the paper tray because some of the mechanical parts (especially the rubber paper feed rollers) were stuck because it hadn't been used regullarly. I then disassembled the whole printer (https://www.ifixit.com/Guide/Repairing+HP+Deskjet+6840+Rubber+Paper+Feed+Rollers/22773) and was able to fix the problem and am now able to print a status page. I will call HP Support again and see whether the region reset will work now.

Communication problem with SCXI 1000 Chasis

I have followed all instructions on this site...
I have a SCXI1000 chasis, in this I have a 1520 strain guage board connected (via connection kit) to a pci-mio-16e1 DAQ card... I can not auto detect the board and when I manually add the board (in MAX) and then verify I get "Card ** missing in slot *whatever slot I am using* "
any suggestions??
The problem might be that the SCXI chassis I am using is second hand.... I am worried it is not poweing the card... even though the "on" light is on... Which are the pins that supply power to the card and what levels should they be at (I can simply verify if it works with a multimeter then)
Thanks in advance,
Scott

Scott;
It's sort of hard to verify if the problem is on the chssis or not by probing some lines. Even if you get the power lines working correctly, the SCXI bus might be damage and you will have that same behavior regardless the power lines state.
The best way to troubleshoot that is by either trying another SCXI module that you know for a fact that is working, or to try that module of yours on a SCXI chassis you that is working.
Hope this helps.
Filipe A.
Applications Engineer
National Instruments

Ipod Nano 6th gen USB problem with JBL 1000 Radio

My Ipod nano 6th generation will nt sync to my JBL Radio sytem through the USB Port. I am trying to download music from my Ipod to the hard drive on my JBL Radio. I have done this before with a different name brand player through the USB Port.
The Nano USB port works on my Lexus Radio system but not my JBL Car Radio.
Is there a compatibility issue with the 6th generation nano USB port and the JBL USB Port? My JBL radio is a J-1000.
Thanks in advance.

Try posting in the iPiod Nano forum. This is the iPod touch forum.

Printing problems with Deskjet 970 Cse

Sometimes when I try to print a pdf file, the printer just prints a few lines of each page and skips the rest. I end up getting several pages output with only a few lines in each page. How can this be fixed? I am running Windows Vista.

The troubleshooting steps in the document here may help. I would also suggest you make sure you have the latest version of Adobe Reader.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Problems with Deskjet 3050A connecting to the computer (Mac)

Hi,
I have recently moved to university and have bought my new printer with me (which I had set up at home). But I am having real problems connecting it to the computer. It doesn't accept the wireless connection because it is secure as it is from the university. The USB connection also doesn't seem to work as it always says that the printer is not connected. I have tried installing the software again and it recognises the printer from the USB, but there is no difference when I try to print something.
Please help as it's essential for my studies!
Thanks

Welcome to the forums. You need to:
1. Bind your desktop machines to your Open Directory master
2. Create groups and user accounts in WorkGroup Manager which allow your users to log into those computers
You will find the User Admin documents here useful:
http://www.apple.com/server/documentation/
hth,
b.

Problems with deskjet 1512

I can't print it keeps asking for file name then it says error cant print

Hello tompriest,
Welcome to the HP Forums!
I see that you cannot print with your HP Deskjet 1512, and I am happy to help you with this issue!
For further assistance, I will need to know the following:
If you are using a Windows or Mac Operating System, and the version number. To find the exact version, visit this link. Whatsmyos.
If the printer is able to make copies by itself.
If the power cable plugged into a surge protector, or directly to the wall outlet. Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector. This applies to Inkjet printers as well.
If you are using Windows, please try the HP Print and Scan Doctor, and let me know what happens.
Hope to hear from you, and thank you for posting!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Problems with DeskJet 500

My DeskJet 500 will only print the first line of a test page, then it will cycle to the next page, print the first line of the test page, cycle to the next page, print the first line of the test page, etc. It would go through a whole stack of paper if I let it go. When I ask to print a document (in a 12pt font) it prints what looks like about 20pt font, three lines at once. I've checked the driver and it seems to be ok. Any ideas? Thanks.

Dear Badcomm,
    I have two ideas about what has happened to your printer. The first idea is that your printer coud have a paper jam. If that is the case you could try to push the the paper button underneath the power button. It should just spit the page out or another blank page. The second idea is that you could have broke the gears on the motor or the trolley that you put the inkcartages into. If that is the case my best bet is to just go out and buy a new printer. I hope this helps.
                       Sincerely,
                                       Wambatt256

Problem with HP Deskjet 1000 J110 cut photo

  Hello,
With any format the document or image is cut to instill
about 2 CM, despite having tried with different programs, also to take away
edges of the press, etc., etc., is that the printer does not estisce those last cm? original:
http://postimg.org/image/dwyzuvoh5/
printed: http://postimg.org/image/wodllbdzb/  Tancks.

@pz1,
Welcome to the forums!
I understand your print jobs are printing out with partial printing on them, and I hope to help!
I am curious to know if the issue could be within the printer hardware itself, and would like you to print out a diagnostic test page to find out.
Please click this link, follow all of the steps and let me know the results:
Fixing Print Quality Problems for the HP Deskjet 1000 (J110), 2000 (J210), 3000 (J310), and HP Deskj...
If you wish to send me a "thank you" for my response to help, click the thumbs up  below!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Unable to communicate with printer-hp deskjet 1000

I have used this Printer for almost 2 yrs and dis problem ne'er occoured before........forst my text print came distorted then it showed offline and later its says printer is ready but when i give the print command......it says "unable to communicate with printer"
Help pls!!!!
This question was solved.
View Solution.

Welcome to the forums niks!
I understand you are having an issue with your Deskjet 1000 showing the message "unable to communicate with printer".
Please let me know which operating system you are running and I will look into this for you.
Help to find which Operating System you are running:
Which Windows Operating System am I running?
Mac OS X: How Do I Find Which Mac OS X Version Is on My Computer?
Happy Monday
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Printing problem with HP deskjet 3050 all in one J610 series

I have a HP deskjet 3050 all in one J610 series which I am using with Windows Vista Version 6.0 (Build 6006: Service pack 2). Connecting is by USB port. I have not used the printer for some time, but have done all the maintence checks & it is good to go. When I want to print a letter the only thing that gets printed is the email address which is coloured blue. I think the problem is in the settings of the printer features. I can print the letter in gray scale but this is not easy to read and not suitable for business dealings.
I would appreciate help with this problem. A definition of the terms used in the printer features might help me resolve it by my self.
Thanks
This question was solved.
View Solution.

Hello @Tellen,
Thank you for visiting the HP Support Forums! I understand you are running into some print quality problems with your HP Deskjet 3050. I see when you attempt to print a letter you will only see the email address and its in blue ink.
First I would like you to click here to download and run the Print and Scan Doctor > www.hp.com/go/tools- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
What does the PSDR find? If you are still not getting black text, please continue here: Fixing Print Quality Problems for the HP Deskjet 3050 (J610) All-in-One Printer Series
If after the troubleshooting has been done and you are still seeing the issue leave me with the following information:
1. What is your current Operating system, Windows or Mac and which version?
2. How is the printer connected, USB or Wireless?
3. If you print a test page from the front panel do you see the same issue?
I hope to hear from you soon.
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Problems with using Deskjet 3745 on 2-PC home network

I have an old PC running Windows XP SP3 and a new one running Windows 7, but only one printer. The network connecting the PCs is on an ADSL router with to its own external Iomega network drive with a USB port.
To make the printer usable on both PCs,
I originally connected it to the Iomega USB port. But the port was effectively a 1-way connection only, so I could not get a print-preview to see which form/profile the printer was using. So I junked that and...
reverted to connecting the printer to one PC permanently and sharing it on the network. But the two PCs required different drivers which would not talk to each other, and the set-up simply would not work.
Finally I went back to the straightforward method of plugging the printer into the USB port of whichever PC I needed to us it on. That worked fine for a while until the WIN 7
print-preview started showing blank images (but printing correctly).
print-spooling failed to cope with cancelled documents.
I have had Deskjet Support's help in trying to sort this out, which including reinstalling the drivers on both PCs - several times! But I am still left with solution 3 giving problems with Win 7.
Has anybody encountered a similar situation and found a satisfactory working solution?
This question was solved.
View Solution.

Try the following: connect the printer to the XP machine and set the XP machine to share this on the network. On the Windows 7 machine go to the Devices and Printers folder, Add a Printer, Local Printer, Create a Port, Local Port, \\Computername\Printername (use the actual share name for the computer and printer), OK, then click on Windows Update and then select the HP (not Hewlett-Packard) Deskjet 3740 series (LiDiL).
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Problem with HP DeskJet 845c in 10.4 Tiger

Recently I migrated an iBook G3 from Mac OS 9 to MacOS X (Tiger 10.4.10). And we also use a new MacBook.
But there's a big problem with the *HP DeskJet 845c* Printer:
- printing works with Word, but *doesn't with AppleWorks or Mail (2.1.1)*
- I have the latest Updates and looked for the latest HP DeskJet software, but this is the newest, version 3.3
- I spoke with HP support, but they said that this is a problem in OS X
- until now in MacOS 9 the printer worked fine
The problem is:
- from Mail only the header will be printed, but not the message itself
- from AppleWorks is ssems as if only the first "pixel-rows are printed from each line
Any help?

Hello, Same problem with HP Deskjet 895Cse. I had printer on my G4 tower running 10.3. My macbook pro was networked through the G4 to printer, all good. I just moved my printer and plugged in directly to macboook pro USB port................ Iregular printing. With normal size fonts, 12, just the top few pixels of each sentence gets printed. With larger fonts like 36 or 48, the print is pretty interesting, but not readable. Sometmes it just spits out pages with 1 sentence, top bit only, on each page. Appleworks, word & pdf's from preview, all print the same. HP alignment, HP test , HP clean all show normal. ?????????????????????

Problem with Deskjet 1000

Similar Messages

Maybe you are looking for