Problem with VPN Client and PIX 7.0(5)

Hi, i have a problem configuring my pix 525 7.0(5) as a remote vpn server. I already configure the pix
sollowing this instructions (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008060f25c.shtml)
and i can establish a vpn using CISCO VPN Client; but i can't reach any resource from my inside network or any network define in the PIX.
I think that could be a missing nat or an acl; but i have do a lot of research but i can figure out the solution.
This is the configuration i apply
access-list cryptomap-scada extended permit ip any 172.10.0.0 255.255.255.0
access-list acl-vpn-sap-remoto extended permit ip any 172.16.42.64 255.255.255.224
access-list acl-vpn-sap-remoto extended permit icmp any 172.16.42.64 255.255.255.224
access-list acl-vpn-sap-remoto extended permit ip any any
access-list acl-vpn-sap-remoto extended permit icmp any any
ip local pool pool_vpn_sap 172.*.*.1-172.10.0.254 mask 255.255.255.0
nat (inside) 0 access-list cryptomap-scada
group-policy VPN_SAP_PED internal
group-policy VPN_SAP_PED attributes
vpn-filter value acl-vpn-sap-remoto
vpn-tunnel-protocol IPSec
username vpnuser password **** encrypted
username vpnuser attributes
vpn-group-policy VPN_SAP_PED
crypto ipsec transform-set vpn-cliente-remoto esp-3des esp-md5-hmac
crypto dynamic-map vpn-remoto-dymap 7 set transform-set vpn-cliente-remoto
crypto dynamic-map vpn-remoto-dymap 7 set reverse-route
crypto map siemens-scada-map 7 ipsec-isakmp dynamic vpn-remoto-dymap
isakmp policy 7 authentication pre-share
isakmp policy 7 encryption 3des
isakmp policy 7 hash sha
isakmp policy 7 group 2
isakmp policy 7 lifetime 43200
tunnel-group VPN_SAP_PED type ipsec-ra
tunnel-group VPN_SAP_PED general-attributes
address-pool pool_vpn_sap
default-group-policy VPN_SAP_PED
tunnel-group VPN_SAP_PED ipsec-attributes
pre-shared-key clavevpnsap
Thanks in Advanced

Hi, thanks for you response, if i remove the acl form de vpn filter, i get the same problem (i can't reach any host). This is the output from the command that you ask for.
PIX-Principal(config)# show running-config nat
nat (inside) 0 access-list cryptomap-scada
nat (inside) 9 JOsorioPC 255.255.255.255
nat (inside) 9 GColinaPC 255.255.255.255
nat (inside) 9 AlfonsoPC 255.255.255.255
nat (inside) 9 AngelPC 255.255.255.255
nat (inside) 9 JerryPC 255.255.255.255
nat (inside) 9 EstebanPC 255.255.255.255
nat (inside) 9 GiancarloPC 255.255.255.255
nat (inside) 9 WilliamsPC 255.255.255.255
nat (inside) 9 PerniaPC 255.255.255.255
nat (inside) 9 ElvisDomPC 255.255.255.255
nat (inside) 8 LBermudezPC 255.255.255.255
nat (inside) 9 HelpDeskPC 255.255.255.255
nat (inside) 9 OscarOPC 255.255.255.255
nat (inside) 9 AnaPC 255.255.255.255
nat (inside) 9 RobertoPC 255.255.255.255
nat (inside) 9 MarthaPC 255.255.255.255
nat (inside) 9 NOCPc5-I 255.255.255.255
nat (inside) 9 NOCPc6-I 255.255.255.255
nat (inside) 9 CiraPC 255.255.255.255
nat (inside) 9 JaimePC 255.255.255.255
nat (inside) 9 EugemarPC 255.255.255.255
nat (inside) 9 JosePC 255.255.255.255
nat (inside) 9 RixioPC 255.255.255.255
nat (inside) 9 DaniellePC 255.255.255.255
nat (inside) 9 NorimarPC 255.255.255.255
nat (inside) 9 NNavaPC 255.255.255.255
nat (inside) 8 ManriquePC 255.255.255.255
nat (inside) 8 MarcialPC 255.255.255.255
nat (inside) 8 JAlbornozPC 255.255.255.255
nat (inside) 9 GUrdanetaPC 255.255.255.255
nat (inside) 9 RVegaPC 255.255.255.255
nat (inside) 9 LLabarcaPC 255.255.255.255
nat (inside) 9 Torondoy-I 255.255.255.255
nat (inside) 9 Escuque-I 255.255.255.255
nat (inside) 9 Turbio-I 255.255.255.255
nat (inside) 9 JoseMora 255.255.255.255
nat (inside) 8 San-Juan-I 255.255.255.255
nat (inside) 8 Router7507 255.255.255.255
nat (inside) 8 NOCPc4-I 255.255.255.255
nat (InterfaceSAN) 8 MonitorHITACHI-I 255.255.255.255

Similar Messages

Problem with VPN Client and network access

We are running VPN client 4.0.1 on our laptops, and there are a number of users who are getting documents they are using on the internal network (off VPN) corrupted. The initial cause seemed to be the stateful firewall, but I have that turned off, and we are still getting it.
It only seems to be on the machines with VPN client installed, and it is only happening when the user is working on a file direct from the network drive. They are not connecting via the VPN client when the problem occurs.
any suggestions?
William.

Did you get any joy with this ? We seem to be having the same issue.
Thanks

WRV200 - Problems with VPN Client and Internal network access

I have a WRV200 router and want to access the internal (Private Network) connected on the inside. I have successfully conected to the router with the Linksys VPN Client, but it does not appear to allow access to the internal network.
How do I enable NAT Transversal or Passthru? I have already selected all of the PPTP, L2TP and IPSEC Pass Through.
Has anyone gotten this to work?

I have actually gotten this to work. Issues surround this include the ability to get to the VPN if the main DNS is down (it does not fail over to the next DNS in the list).
If you unselect all of the boxes in the firewall General configuration, you can connect, but if you need to have all of this unchecked, what's the sense of having it?
Anyway, you can use the DoS Prevention, this is not interfering.
HTH.

Cisco ASA 8.3(1) with VPN Client and IP Communicator - one way communication

Hi Community.
I have a strange problem with my setup and I'm pretty sure it's either some type of routing (or NAT) or just a missing rule allowing the traffic. But I'm now at a point where I'd like to request your help.
I have some remote access users who have the Cisco IP Communicator (CIPC) installed on their notebooks. So:
VPN user with CIPC <> ASA Firewall <> Voice Router <> CCM <> IP Phone
The VPN works fine for any other traffic. Also the basic connection for the IP Communicator works fine. It get's connected to the CallManager, is shown as registered and you even can call an internal phone and also external phones. BUT: while you can hear the called party (so the internal phone) it doesn't work for the other way. There is no sound coming from the remote/caller.
I already figured out that it's also not possible to ping from the VPN phone to the internal IP Phone subnet. While the VPN user can ping any other device in the internal network, he can't do it to the Cisco IP Phones. But if the VPN phone calls a none-internal phone (mobiles...) - it works!
My thought is that the call can't be build up correctly between the VPN phone and the internal phone.
I found similiar situations with google but they are all for the other way around: call to internal works, but not to VPN.
What do you think?

Hi,
Typically ASA lists specific networks to the VPN Client when Split Tunnel is used.
This would mean that there is a Split Tunnel ACL used in the ASA configurations for this VPN connection which needs to have the missing network added for the traffic to be tunneled to the VPN connection.
- Jouni

How to configure full tunnel with VPN client and router?

I know the concept of split tunnel....Is it possibe to configure vpn client and router full tunnel or instead of router ASA? I know filter options in concentrators is teher options in ISR routers or ASA?

I think it is possible. Following links may help you
http://www.cisco.com/en/US/products/hw/routers/ps274/products_configuration_example09186a0080819289.shtml

Problem with VPN client on Cisco 1801

Hi,
I have configured a new router for a customer.
All works fine but i have a strange issue with the VPN client.
When i start the VPN the client don't close the connection, ask for password, start to negotiate security policy the show the not connected status.
This is the log form the VPN client:
Cisco Systems VPN Client Version 5.0.07.0290
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1      14:37:59.133 04/08/13 Sev=Info/6          GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
2      14:38:01.321 04/08/13 Sev=Info/4          CM/0x63100002
Begin connection process
3      14:38:01.335 04/08/13 Sev=Info/4          CM/0x63100004
Establish secure connection
4      14:38:01.335 04/08/13 Sev=Info/4          CM/0x63100024
Attempt connection with server "asgardvpn.dyndns.info"
5      14:38:02.380 04/08/13 Sev=Info/6          IKE/0x6300003B
Attempting to establish a connection with 79.52.36.120.
6      14:38:02.384 04/08/13 Sev=Info/4          IKE/0x63000001
Starting IKE Phase 1 Negotiation
7      14:38:02.388 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 79.52.36.120
8      14:38:02.396 04/08/13 Sev=Info/4          IPSEC/0x63700008
IPSec driver successfully started
9      14:38:02.396 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
10     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x6300002F
Received ISAKMP packet: peer = 79.52.36.120
11     14:38:02.460 04/08/13 Sev=Info/4          IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, VID(Unity), VID(dpd), VID(?), VID(Xauth), VID(Nat-T), KE, ID, NON, HASH, NAT-D, NAT-D) from 79.52.36.120
12     14:38:02.506 04/08/13 Sev=Info/6          GUI/0x63B00012
Authentication request attributes is 6h.
13     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer is a Cisco-Unity compliant peer
14     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports DPD
15     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports DWR Code and DWR Text
16     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports XAUTH
17     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports NAT-T
18     14:38:02.465 04/08/13 Sev=Info/6          IKE/0x63000001
IOS Vendor ID Contruction successful
19     14:38:02.465 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 79.52.36.120
20     14:38:02.465 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
21     14:38:02.465 04/08/13 Sev=Info/4          IKE/0x63000083
IKE Port in use - Local Port = 0xCEFD, Remote Port = 0x1194
22     14:38:02.465 04/08/13 Sev=Info/5          IKE/0x63000072
Automatic NAT Detection Status:
   Remote end is NOT behind a NAT device
   This   end IS behind a NAT device
23     14:38:02.465 04/08/13 Sev=Info/4          CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
24     14:38:02.502 04/08/13 Sev=Info/5          IKE/0x6300002F
Received ISAKMP packet: peer = 79.52.36.120
25     14:38:02.502 04/08/13 Sev=Info/4          IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 79.52.36.120
26     14:38:02.502 04/08/13 Sev=Info/4          CM/0x63100015
Launch xAuth application
27     14:38:07.623 04/08/13 Sev=Info/4          CM/0x63100017
xAuth application returned
28     14:38:07.623 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 79.52.36.120
29     14:38:12.656 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
30     14:38:22.808 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
31     14:38:32.949 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
32     14:38:43.089 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
33     14:38:53.230 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
34     14:39:03.371 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
35     14:39:13.514 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
36     14:39:23.652 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
37     14:39:33.807 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
38     14:39:43.948 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
39     14:39:54.088 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
40     14:40:04.233 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
41     14:40:14.384 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
42     14:40:24.510 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
43     14:40:34.666 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
44     14:40:44.807 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
45     14:40:54.947 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
46     14:41:05.090 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
47     14:41:15.230 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
48     14:41:25.370 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
49     14:41:35.524 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
50     14:41:45.665 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
51     14:41:55.805 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
52     14:42:05.951 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
53     14:42:16.089 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
54     14:42:26.228 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
55     14:42:36.383 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
56     14:42:46.523 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
57     14:42:56.664 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
58     14:43:02.748 04/08/13 Sev=Info/4          IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=2B1FFC3754E3B290 R_Cookie=73D546631A33B5D6) reason = DEL_REASON_CANNOT_AUTH
59     14:43:02.748 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DWR) to 79.52.36.120
60     14:43:03.248 04/08/13 Sev=Info/4          IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=2B1FFC3754E3B290 R_Cookie=73D546631A33B5D6) reason = DEL_REASON_CANNOT_AUTH
61     14:43:03.248 04/08/13 Sev=Info/4          CM/0x63100014
Unable to establish Phase 1 SA with server "asgardvpn.dyndns.info" because of "DEL_REASON_CANNOT_AUTH"
62     14:43:03.248 04/08/13 Sev=Info/5          CM/0x63100025
Initializing CVPNDrv
63     14:43:03.262 04/08/13 Sev=Info/6          CM/0x63100046
Set tunnel established flag in registry to 0.
64     14:43:03.262 04/08/13 Sev=Info/4          IKE/0x63000001
IKE received signal to terminate VPN connection
65     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
66     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
67     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
68     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x6370000A
IPSec driver successfully stopped
And this is the conf from the 1801:
hostname xxx
boot-start-marker
boot-end-marker
enable secret 5 xxx
aaa new-model
aaa authentication login xauthlist local
aaa authorization network groupauthor local
aaa session-id common
dot11 syslog
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.0.1.1 10.0.1.10
ip dhcp excluded-address 10.0.1.60 10.0.1.200
ip dhcp excluded-address 10.0.1.225
ip dhcp excluded-address 10.0.1.250
ip dhcp pool LAN
   network 10.0.1.0 255.255.255.0
   default-router 10.0.1.10
   dns-server 10.0.1.200 8.8.8.8
   domain-name xxx
   lease infinite
ip name-server 10.0.1.200
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip inspect log drop-pkt
ip inspect name Firewall cuseeme
ip inspect name Firewall dns
ip inspect name Firewall ftp
ip inspect name Firewall h323
ip inspect name Firewall icmp
ip inspect name Firewall imap
ip inspect name Firewall pop3
ip inspect name Firewall rcmd
ip inspect name Firewall realaudio
ip inspect name Firewall rtsp
ip inspect name Firewall esmtp
ip inspect name Firewall sqlnet
ip inspect name Firewall streamworks
ip inspect name Firewall tftp
ip inspect name Firewall vdolive
ip inspect name Firewall udp
ip inspect name Firewall tcp
ip inspect name Firewall https
ip inspect name Firewall http
multilink bundle-name authenticated
username xxx password 0 xxxx
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group xxx
key xxx
dns 10.0.1.200
wins 10.0.1.200
domain xxx
pool ippool
acl 101
crypto ipsec transform-set myset esp-3des esp-sha-hmac
crypto ipsec transform-set xauthtransform esp-des esp-md5-hmac
crypto dynamic-map dynmap 10
set transform-set myset
crypto map clientmap client authentication list userauthen
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
archive
log config
hidekeys
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode adsl2+
hold-queue 224 in
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Vlan1
ip address 10.0.1.10 255.255.255.0
ip nat inside
ip virtual-reassembly
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp pap sent-username aliceadsl password 0 aliceadsl
crypto map clientmap
ip local pool ippool 10.16.20.1 10.16.20.200
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
ip route 0.0.0.0 0.0.0.0 10.0.1.2
ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
ip nat inside source static udp 10.0.1.60 1056 interface Dialer0 1056
ip nat inside source static tcp 10.0.1.60 1056 interface Dialer0 1056
ip nat inside source static tcp 10.0.1.60 3111 interface Dialer0 3111
ip nat inside source static udp 10.0.1.60 3111 interface Dialer0 3111
ip nat inside source list 101 interface Dialer0 overload
access-list 101 remark *** ACL nonat ***
access-list 101 deny   ip 10.0.1.0 0.0.0.255 10.16.20.0 0.0.0.255
access-list 101 permit ip 10.0.1.0 0.0.0.255 any
access-list 150 remark *** ACL split tunnel ***
access-list 150 permit ip 10.0.1.0 0.0.0.255 10.16.20.0 0.0.0.255
control-plane
line con 0
no modem enable
line aux 0
line vty 0 4
password xxx
scheduler max-task-time 5000
end
Anyone can help me ?
Sometimes the vpn can be vreated using the iPhone or iPad vpn client...

I am having a simuliar issue with my ASA 5505 that I have set up. I am trying to VPN into the Office. I have no problem accessing the Office network when I am on the internet without the ASA 5505. After I installed the 5505, and there is internet access, I try to connect to the Office network without success. The VPN connects with the following error.
3 Dec 31 2007 05:30:00 305006 xxx.xx.114.97
regular translation creation failed for protocol 50 src inside:192.168.1.9 dst outside:xxx.xx.114.97
HELP?

Problem with VPN Client passthrough on ASA 5505

I am having a problem with passing through a VPN client connection on an ASA 5505. The ASA is running version 8 and terminates an anyconnect VPN. The ASA is using PAT. When the inside user connects with the VPN client, it connects but no traffic passes through the tunnel. I see the error
305006 regular translation creation failed for protocol 50 src INSIDE:y.y.y.y dst OUTSIDE:x.x.x.x
UDP 500,4500 and ESP are allowed into the ASA. Ipsec inspection has also been setup on a global policy, but the user still cannot pass traffice to the remote VPN he is connected through.
At the Main Office we have an ASA 5510 that terminates a site to site VPN, allows remote connections with PAT and allows passthrough no problems. Any ideas?

I am having a simuliar issue with my ASA 5505 that I have set up. I am trying to VPN into the Office. I have no problem accessing the Office network when I am on the internet without the ASA 5505. After I installed the 5505, and there is internet access, I try to connect to the Office network without success. The VPN connects with the following error.
3 Dec 31 2007 05:30:00 305006 xxx.xx.114.97
regular translation creation failed for protocol 50 src inside:192.168.1.9 dst outside:xxx.xx.114.97
HELP?

Problems with VPN-Client 5.0 instoled on Windows Vista over ADSL Conecction

Hi, I have severals clients that they use Windows Vista and connects throw there lan over a VPN-Client. The clients that has an ADSL connection in there hose has disconect problems. Do you know why?? Do you know same workarround to do?? Thanks.
Regards.

Make sure that you have the right cable pinout and that your ISP has turned on the DSL service. Troubleshoot the DSL connection by watching the modem state of the ADSL interface as the line retrains.
To use the VPN Client, you need
- Direct network connection (cable or DSL modem and network adapter/interface card), or
- Internal or external modem
For further more troubleshoot click this link,
http://www.cisco.com/en/US/docs/security/vpn_client/cisco_vpn_client/vpn_client500_501/release/notes/51client.html#wp1550392

Problem with Cisco VPN client and HP elitebook 2530p windows 7 64-bit

Hi there
I have a HP Elitebook 2530p which i upgraded to windows 7 64-bit. I installed the Cisco VPN client application (ver. 5.0.07.0290 and also 64-bit) and the HP connection manager to connect to the internet through a modem Qualcomm gobi 1000 (that is inside the laptop). When I connect to the VPN, it connects (I write the username and password) but there is no traffic inside de virtual adapter for my servers. When I connect to the internet through wire or wireless internet, I connect de VPN client and there is no problem to establish communication to my servers.
I tried everything, also change the driver and an earlier version of the HP connection manager application. I also talked to HP and they told me that there was a report with this kind of problem and it was delivered to Cisco. I don’t know where is the problem.
Could anyone help me?
Thanks to all.

You can try to update Deterministic Network Enhancer to the below listed release which supports
WWAN Drivers.
http://www.citrix.com/lang/English/lp/lp_1680845.asp.
DNE now supports WWAN devices in Win7. Before downloading the latest version of DNEUpdate from the links below, be sure you have the latest
drivers for your network adapters by downloading them from the vendors websites.
For 64-bit: ftp://files.citrix.com/dneupdate64.msi
Hope that helps.

Mavericks VPN dropouts with native VPN client and Cisco IPSec

Since update to Maverics I am experiencing VPN dropouts with native VPN client and Cisco IPSec
I am connecting via a WIFI router to a remote VPN server
The conenction is good for a while but eventually it drops out.
I had Zero issues in mountain lion and only have issues since the update to 10.9
I had similar issues in teh past with an unrelaibel wifi router but i am using a Verizon Fios router and it has worked impecably until mavericks
My thoughts are:
1 -issue with mavericks ( maybe the app sleep funciton affecting eithe VPN or WIFI daemons)
2- Issue with cisco router compaitibility or timing with Cisco IPSEC
3- Issue with WIFI itself on mavericks - some sort of WIFI software bug
Any thousuggestions?

Since update to Maverics I am experiencing VPN dropouts with native VPN client and Cisco IPSec
I am connecting via a WIFI router to a remote VPN server
The conenction is good for a while but eventually it drops out.
I had Zero issues in mountain lion and only have issues since the update to 10.9
I had similar issues in teh past with an unrelaibel wifi router but i am using a Verizon Fios router and it has worked impecably until mavericks
My thoughts are:
1 -issue with mavericks ( maybe the app sleep funciton affecting eithe VPN or WIFI daemons)
2- Issue with cisco router compaitibility or timing with Cisco IPSEC
3- Issue with WIFI itself on mavericks - some sort of WIFI software bug
Any thousuggestions?

Boot camp with Cisco VPN client and smart card

Looking at a Macbook or Macbook Air and the only reason I need to run windows is to be able to access my work network through the Cisco VPN client and my Smartcard then use remote desktop. From my understanding if I run Bootcamp it should work am I correct? Im going to an Apple store tomorrow hopefully they can help too.
Thanks

mrbacklash wrote:
Ok with that being said will the MBA 11.6 1.4ghz have the guts to make it run mostly internet based programs over the VPN connection?
I think if you are running apps over the Internet the bottleneck will be the Internet and your VPN bandwidth. Your computer can certainly execute faster than Internet communications.
Besides, Internet or remote applications run on the remote server. All your local computer does is local processing of the data if necessary.
Message was edited by: BobTheFisherman

I want to go back to the previous 2014.2 version. .3 is much too buggy and full of error messages. Creating problems as I am on a timeline with my client and I don't have time to fool around with all the problems.

2014 .3 is much too buggy and full of error messages. Creating problems as I am on a timeline with my client and I don't have time to fool around with all the problems.

You didn't mention what error(s) you've encountered? A workaround for the most commonly hit problem is here Re: error in Muse : Object UID:U6875 has two (or more) owners: U3633 and U3165
If you have a copy of your .muse file that has not been saved using 2014.3, you can downgrade by uninstalling Muse and then choose Previous Version in the Filters drop down in the Apps panel of the Creative Cloud desktop app. There will be a popup next to Muse where you can select a prior version to install.

Problems with games server and client

Hi! I am making an MMORPG game and I have problems with the server and client connection.
I can connect to the server, but when a second player does, the server console tells me this:
java.net.SocketException: Connection reset
After that, all clients disconnect.
Which is the problem?
How can I solve it?
Thank you so much

Here is how my sever work. I took some of this code from a book called Killer Programming Games in Java. If you google for it, you will find it for sure.
TourGroup tg = new TourGroup(); // this object stores information about all clients connected to the server
    try {
      ServerSocket serverSock = new ServerSocket(PORT);
      Socket clientSock;
      while (true) {
        System.out.println("Waiting for a client...");
        clientSock = serverSock.accept();
        new TourServerHandler(clientSock, tg).start(); // this is the thread that monitors each client
    catch(Exception e)
    { System.out.println(e); }
} This is some code of TourServerHandler
public TourServerHandler(Socket s, TourGroup tg)
    this.tg = tg;
    clientSock = s;
    name= "?";
    cliAddr = clientSock.getInetAddress().getHostAddress();
    port = clientSock.getPort();
    System.out.println("Client connection from (" +
                 cliAddr + ", " + port + ")");
public void run()
// process messages from the client
    try {
      // Get I/O streams from the socket
      BufferedReader in = new BufferedReader(
   new InputStreamReader( clientSock.getInputStream() ) );
      PrintWriter out =
new PrintWriter( clientSock.getOutputStream(), true );
// and here goes the rest... The TourServerHandler thread uses this code to send messages:
tg.broadcast(msg); tg.broadcast works like this:
synchronized public void broadcast(String cliAddr, int port, String msg)
// broadcast to everyone but original msg sender
    TouristInfo c; // this object stores info about the client
    for(int i=0; i < tourPeople.size(); i++) {
      c = (TouristInfo) tourPeople.get(i);
        c.sendMessage(msg);
} This is the error part
public void sendMessage(String msg)
PrintWriter out;
    out.println(msg);
      System.out.println("OK");
} I can't find any error but I still get that Connection reset exception...

We encountered a problem with some client machines that use Firefox version 24ESR and IE8. Ajax requests of aspx pages from Firefox are getting the following er

I encountered a problem with some client machines that use Firefox version 24ESR and IE8.
Ajax requests of aspx pages from Firefox are getting the following error from the iis server (iis version 7.5):
Bad Request - Request Too Long
HTTP Error 400. The size of the request headers is too long.
From analyzing the request that was sent to the server, I saw that the request consist of only the viewstate of the aspx page.
I tried to disable the viewstate for one page and the server got the request correctly.
I do not encounter any issues on these laptops with postback requests from Firefox or when running the same application with IE8.

Sometimes that means that the page address sent is loo long.
Check the link address you are using.
I can't help you further and will send for more help.

VPN Client and Windows 7 - Window won't show

Bizarre issue I've now experienced on two separate PC's with VPN Client 5.00.07.0410 on 32-bit Windows 7:
Out of the blue, when the user double-clicks the Cisco VPN Client icon, the lock shows up in the system tray, and the application shows in the taskbar. You may get a glimpse of the window when you double-click the taskbar icon, or single click it and choose the application from the list. However, you are not able to actually get the window to be visible. This of course makes it impossible for the user to click the "connect" button.
I've discovered that when the icon is in the taskbar, and you hit "Enter" on the keyboard, it will connect. However I wouldn't expect a user to be able to figure this out, and so it was quite frustrating for them when this happened.
I've noticed there is a new version of the software for 64-bit users, but not for 32.
Anybody else experience this? Find a solution?
I tried uninstalling/re-installing and it made no difference.
-Chris

Try this so you don't have to do it each time... it worked for XP Pro 32-bit (Dell E6410). Haven't yet encountered on W7 Pro:
Bring up Task Manager (Ctrl+Alt_Delete). Open the Applications tab. Highlight VPN Client, right-click and select Maximize. (Sometimes if the system dies (power-loss) when connected to VPN the registry remembers the minimized setting and will not un-minimize it except with this process (and maybe one yet to be determined).)
I'm currently working (20140617) on a similar issue for W7 Pro for the User Authentication window where the RSA passcode needs to be entered. Alt-Tab works but I'm trying to make it permanent. (One problem is the user has a difficult time following instructions.)

Problem with VPN Client and PIX 7.0(5)

Similar Messages

Maybe you are looking for