Problem with VPN Client and network access

We are running VPN client 4.0.1 on our laptops, and there are a number of users who are getting documents they are using on the internal network (off VPN) corrupted. The initial cause seemed to be the stateful firewall, but I have that turned off, and we are still getting it.
It only seems to be on the machines with VPN client installed, and it is only happening when the user is working on a file direct from the network drive. They are not connecting via the VPN client when the problem occurs.
any suggestions?
William.

Did you get any joy with this ? We seem to be having the same issue.
Thanks

Similar Messages

WRV200 - Problems with VPN Client and Internal network access

I have a WRV200 router and want to access the internal (Private Network) connected on the inside. I have successfully conected to the router with the Linksys VPN Client, but it does not appear to allow access to the internal network.
How do I enable NAT Transversal or Passthru? I have already selected all of the PPTP, L2TP and IPSEC Pass Through.
Has anyone gotten this to work?

I have actually gotten this to work. Issues surround this include the ability to get to the VPN if the main DNS is down (it does not fail over to the next DNS in the list).
If you unselect all of the boxes in the firewall General configuration, you can connect, but if you need to have all of this unchecked, what's the sense of having it?
Anyway, you can use the DoS Prevention, this is not interfering.
HTH.

Problem with VPN Client and PIX 7.0(5)

Hi, i have a problem configuring my pix 525 7.0(5) as a remote vpn server. I already configure the pix
sollowing this instructions (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008060f25c.shtml)
and i can establish a vpn using CISCO VPN Client; but i can't reach any resource from my inside network or any network define in the PIX.
I think that could be a missing nat or an acl; but i have do a lot of research but i can figure out the solution.
This is the configuration i apply
access-list cryptomap-scada extended permit ip any 172.10.0.0 255.255.255.0
access-list acl-vpn-sap-remoto extended permit ip any 172.16.42.64 255.255.255.224
access-list acl-vpn-sap-remoto extended permit icmp any 172.16.42.64 255.255.255.224
access-list acl-vpn-sap-remoto extended permit ip any any
access-list acl-vpn-sap-remoto extended permit icmp any any
ip local pool pool_vpn_sap 172.*.*.1-172.10.0.254 mask 255.255.255.0
nat (inside) 0 access-list cryptomap-scada
group-policy VPN_SAP_PED internal
group-policy VPN_SAP_PED attributes
vpn-filter value acl-vpn-sap-remoto
vpn-tunnel-protocol IPSec
username vpnuser password **** encrypted
username vpnuser attributes
vpn-group-policy VPN_SAP_PED
crypto ipsec transform-set vpn-cliente-remoto esp-3des esp-md5-hmac
crypto dynamic-map vpn-remoto-dymap 7 set transform-set vpn-cliente-remoto
crypto dynamic-map vpn-remoto-dymap 7 set reverse-route
crypto map siemens-scada-map 7 ipsec-isakmp dynamic vpn-remoto-dymap
isakmp policy 7 authentication pre-share
isakmp policy 7 encryption 3des
isakmp policy 7 hash sha
isakmp policy 7 group 2
isakmp policy 7 lifetime 43200
tunnel-group VPN_SAP_PED type ipsec-ra
tunnel-group VPN_SAP_PED general-attributes
address-pool pool_vpn_sap
default-group-policy VPN_SAP_PED
tunnel-group VPN_SAP_PED ipsec-attributes
pre-shared-key clavevpnsap
Thanks in Advanced

Hi, thanks for you response, if i remove the acl form de vpn filter, i get the same problem (i can't reach any host). This is the output from the command that you ask for.
PIX-Principal(config)# show running-config nat
nat (inside) 0 access-list cryptomap-scada
nat (inside) 9 JOsorioPC 255.255.255.255
nat (inside) 9 GColinaPC 255.255.255.255
nat (inside) 9 AlfonsoPC 255.255.255.255
nat (inside) 9 AngelPC 255.255.255.255
nat (inside) 9 JerryPC 255.255.255.255
nat (inside) 9 EstebanPC 255.255.255.255
nat (inside) 9 GiancarloPC 255.255.255.255
nat (inside) 9 WilliamsPC 255.255.255.255
nat (inside) 9 PerniaPC 255.255.255.255
nat (inside) 9 ElvisDomPC 255.255.255.255
nat (inside) 8 LBermudezPC 255.255.255.255
nat (inside) 9 HelpDeskPC 255.255.255.255
nat (inside) 9 OscarOPC 255.255.255.255
nat (inside) 9 AnaPC 255.255.255.255
nat (inside) 9 RobertoPC 255.255.255.255
nat (inside) 9 MarthaPC 255.255.255.255
nat (inside) 9 NOCPc5-I 255.255.255.255
nat (inside) 9 NOCPc6-I 255.255.255.255
nat (inside) 9 CiraPC 255.255.255.255
nat (inside) 9 JaimePC 255.255.255.255
nat (inside) 9 EugemarPC 255.255.255.255
nat (inside) 9 JosePC 255.255.255.255
nat (inside) 9 RixioPC 255.255.255.255
nat (inside) 9 DaniellePC 255.255.255.255
nat (inside) 9 NorimarPC 255.255.255.255
nat (inside) 9 NNavaPC 255.255.255.255
nat (inside) 8 ManriquePC 255.255.255.255
nat (inside) 8 MarcialPC 255.255.255.255
nat (inside) 8 JAlbornozPC 255.255.255.255
nat (inside) 9 GUrdanetaPC 255.255.255.255
nat (inside) 9 RVegaPC 255.255.255.255
nat (inside) 9 LLabarcaPC 255.255.255.255
nat (inside) 9 Torondoy-I 255.255.255.255
nat (inside) 9 Escuque-I 255.255.255.255
nat (inside) 9 Turbio-I 255.255.255.255
nat (inside) 9 JoseMora 255.255.255.255
nat (inside) 8 San-Juan-I 255.255.255.255
nat (inside) 8 Router7507 255.255.255.255
nat (inside) 8 NOCPc4-I 255.255.255.255
nat (InterfaceSAN) 8 MonitorHITACHI-I 255.255.255.255

Cisco ASA 8.3(1) with VPN Client and IP Communicator - one way communication

Hi Community.
I have a strange problem with my setup and I'm pretty sure it's either some type of routing (or NAT) or just a missing rule allowing the traffic. But I'm now at a point where I'd like to request your help.
I have some remote access users who have the Cisco IP Communicator (CIPC) installed on their notebooks. So:
VPN user with CIPC <> ASA Firewall <> Voice Router <> CCM <> IP Phone
The VPN works fine for any other traffic. Also the basic connection for the IP Communicator works fine. It get's connected to the CallManager, is shown as registered and you even can call an internal phone and also external phones. BUT: while you can hear the called party (so the internal phone) it doesn't work for the other way. There is no sound coming from the remote/caller.
I already figured out that it's also not possible to ping from the VPN phone to the internal IP Phone subnet. While the VPN user can ping any other device in the internal network, he can't do it to the Cisco IP Phones. But if the VPN phone calls a none-internal phone (mobiles...) - it works!
My thought is that the call can't be build up correctly between the VPN phone and the internal phone.
I found similiar situations with google but they are all for the other way around: call to internal works, but not to VPN.
What do you think?

Hi,
Typically ASA lists specific networks to the VPN Client when Split Tunnel is used.
This would mean that there is a Split Tunnel ACL used in the ASA configurations for this VPN connection which needs to have the missing network added for the traffic to be tunneled to the VPN connection.
- Jouni

How to configure full tunnel with VPN client and router?

I know the concept of split tunnel....Is it possibe to configure vpn client and router full tunnel or instead of router ASA? I know filter options in concentrators is teher options in ISR routers or ASA?

I think it is possible. Following links may help you
http://www.cisco.com/en/US/products/hw/routers/ps274/products_configuration_example09186a0080819289.shtml

Problem with VPN client on Cisco 1801

Hi,
I have configured a new router for a customer.
All works fine but i have a strange issue with the VPN client.
When i start the VPN the client don't close the connection, ask for password, start to negotiate security policy the show the not connected status.
This is the log form the VPN client:
Cisco Systems VPN Client Version 5.0.07.0290
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1      14:37:59.133 04/08/13 Sev=Info/6          GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
2      14:38:01.321 04/08/13 Sev=Info/4          CM/0x63100002
Begin connection process
3      14:38:01.335 04/08/13 Sev=Info/4          CM/0x63100004
Establish secure connection
4      14:38:01.335 04/08/13 Sev=Info/4          CM/0x63100024
Attempt connection with server "asgardvpn.dyndns.info"
5      14:38:02.380 04/08/13 Sev=Info/6          IKE/0x6300003B
Attempting to establish a connection with 79.52.36.120.
6      14:38:02.384 04/08/13 Sev=Info/4          IKE/0x63000001
Starting IKE Phase 1 Negotiation
7      14:38:02.388 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 79.52.36.120
8      14:38:02.396 04/08/13 Sev=Info/4          IPSEC/0x63700008
IPSec driver successfully started
9      14:38:02.396 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
10     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x6300002F
Received ISAKMP packet: peer = 79.52.36.120
11     14:38:02.460 04/08/13 Sev=Info/4          IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, VID(Unity), VID(dpd), VID(?), VID(Xauth), VID(Nat-T), KE, ID, NON, HASH, NAT-D, NAT-D) from 79.52.36.120
12     14:38:02.506 04/08/13 Sev=Info/6          GUI/0x63B00012
Authentication request attributes is 6h.
13     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer is a Cisco-Unity compliant peer
14     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports DPD
15     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports DWR Code and DWR Text
16     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports XAUTH
17     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports NAT-T
18     14:38:02.465 04/08/13 Sev=Info/6          IKE/0x63000001
IOS Vendor ID Contruction successful
19     14:38:02.465 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 79.52.36.120
20     14:38:02.465 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
21     14:38:02.465 04/08/13 Sev=Info/4          IKE/0x63000083
IKE Port in use - Local Port = 0xCEFD, Remote Port = 0x1194
22     14:38:02.465 04/08/13 Sev=Info/5          IKE/0x63000072
Automatic NAT Detection Status:
   Remote end is NOT behind a NAT device
   This   end IS behind a NAT device
23     14:38:02.465 04/08/13 Sev=Info/4          CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
24     14:38:02.502 04/08/13 Sev=Info/5          IKE/0x6300002F
Received ISAKMP packet: peer = 79.52.36.120
25     14:38:02.502 04/08/13 Sev=Info/4          IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 79.52.36.120
26     14:38:02.502 04/08/13 Sev=Info/4          CM/0x63100015
Launch xAuth application
27     14:38:07.623 04/08/13 Sev=Info/4          CM/0x63100017
xAuth application returned
28     14:38:07.623 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 79.52.36.120
29     14:38:12.656 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
30     14:38:22.808 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
31     14:38:32.949 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
32     14:38:43.089 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
33     14:38:53.230 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
34     14:39:03.371 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
35     14:39:13.514 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
36     14:39:23.652 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
37     14:39:33.807 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
38     14:39:43.948 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
39     14:39:54.088 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
40     14:40:04.233 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
41     14:40:14.384 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
42     14:40:24.510 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
43     14:40:34.666 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
44     14:40:44.807 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
45     14:40:54.947 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
46     14:41:05.090 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
47     14:41:15.230 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
48     14:41:25.370 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
49     14:41:35.524 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
50     14:41:45.665 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
51     14:41:55.805 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
52     14:42:05.951 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
53     14:42:16.089 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
54     14:42:26.228 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
55     14:42:36.383 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
56     14:42:46.523 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
57     14:42:56.664 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
58     14:43:02.748 04/08/13 Sev=Info/4          IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=2B1FFC3754E3B290 R_Cookie=73D546631A33B5D6) reason = DEL_REASON_CANNOT_AUTH
59     14:43:02.748 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DWR) to 79.52.36.120
60     14:43:03.248 04/08/13 Sev=Info/4          IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=2B1FFC3754E3B290 R_Cookie=73D546631A33B5D6) reason = DEL_REASON_CANNOT_AUTH
61     14:43:03.248 04/08/13 Sev=Info/4          CM/0x63100014
Unable to establish Phase 1 SA with server "asgardvpn.dyndns.info" because of "DEL_REASON_CANNOT_AUTH"
62     14:43:03.248 04/08/13 Sev=Info/5          CM/0x63100025
Initializing CVPNDrv
63     14:43:03.262 04/08/13 Sev=Info/6          CM/0x63100046
Set tunnel established flag in registry to 0.
64     14:43:03.262 04/08/13 Sev=Info/4          IKE/0x63000001
IKE received signal to terminate VPN connection
65     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
66     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
67     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
68     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x6370000A
IPSec driver successfully stopped
And this is the conf from the 1801:
hostname xxx
boot-start-marker
boot-end-marker
enable secret 5 xxx
aaa new-model
aaa authentication login xauthlist local
aaa authorization network groupauthor local
aaa session-id common
dot11 syslog
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.0.1.1 10.0.1.10
ip dhcp excluded-address 10.0.1.60 10.0.1.200
ip dhcp excluded-address 10.0.1.225
ip dhcp excluded-address 10.0.1.250
ip dhcp pool LAN
   network 10.0.1.0 255.255.255.0
   default-router 10.0.1.10
   dns-server 10.0.1.200 8.8.8.8
   domain-name xxx
   lease infinite
ip name-server 10.0.1.200
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip inspect log drop-pkt
ip inspect name Firewall cuseeme
ip inspect name Firewall dns
ip inspect name Firewall ftp
ip inspect name Firewall h323
ip inspect name Firewall icmp
ip inspect name Firewall imap
ip inspect name Firewall pop3
ip inspect name Firewall rcmd
ip inspect name Firewall realaudio
ip inspect name Firewall rtsp
ip inspect name Firewall esmtp
ip inspect name Firewall sqlnet
ip inspect name Firewall streamworks
ip inspect name Firewall tftp
ip inspect name Firewall vdolive
ip inspect name Firewall udp
ip inspect name Firewall tcp
ip inspect name Firewall https
ip inspect name Firewall http
multilink bundle-name authenticated
username xxx password 0 xxxx
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group xxx
key xxx
dns 10.0.1.200
wins 10.0.1.200
domain xxx
pool ippool
acl 101
crypto ipsec transform-set myset esp-3des esp-sha-hmac
crypto ipsec transform-set xauthtransform esp-des esp-md5-hmac
crypto dynamic-map dynmap 10
set transform-set myset
crypto map clientmap client authentication list userauthen
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
archive
log config
hidekeys
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode adsl2+
hold-queue 224 in
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Vlan1
ip address 10.0.1.10 255.255.255.0
ip nat inside
ip virtual-reassembly
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp pap sent-username aliceadsl password 0 aliceadsl
crypto map clientmap
ip local pool ippool 10.16.20.1 10.16.20.200
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
ip route 0.0.0.0 0.0.0.0 10.0.1.2
ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
ip nat inside source static udp 10.0.1.60 1056 interface Dialer0 1056
ip nat inside source static tcp 10.0.1.60 1056 interface Dialer0 1056
ip nat inside source static tcp 10.0.1.60 3111 interface Dialer0 3111
ip nat inside source static udp 10.0.1.60 3111 interface Dialer0 3111
ip nat inside source list 101 interface Dialer0 overload
access-list 101 remark *** ACL nonat ***
access-list 101 deny   ip 10.0.1.0 0.0.0.255 10.16.20.0 0.0.0.255
access-list 101 permit ip 10.0.1.0 0.0.0.255 any
access-list 150 remark *** ACL split tunnel ***
access-list 150 permit ip 10.0.1.0 0.0.0.255 10.16.20.0 0.0.0.255
control-plane
line con 0
no modem enable
line aux 0
line vty 0 4
password xxx
scheduler max-task-time 5000
end
Anyone can help me ?
Sometimes the vpn can be vreated using the iPhone or iPad vpn client...

I am having a simuliar issue with my ASA 5505 that I have set up. I am trying to VPN into the Office. I have no problem accessing the Office network when I am on the internet without the ASA 5505. After I installed the 5505, and there is internet access, I try to connect to the Office network without success. The VPN connects with the following error.
3 Dec 31 2007 05:30:00 305006 xxx.xx.114.97
regular translation creation failed for protocol 50 src inside:192.168.1.9 dst outside:xxx.xx.114.97
HELP?

Problem with VPN Client passthrough on ASA 5505

I am having a problem with passing through a VPN client connection on an ASA 5505. The ASA is running version 8 and terminates an anyconnect VPN. The ASA is using PAT. When the inside user connects with the VPN client, it connects but no traffic passes through the tunnel. I see the error
305006 regular translation creation failed for protocol 50 src INSIDE:y.y.y.y dst OUTSIDE:x.x.x.x
UDP 500,4500 and ESP are allowed into the ASA. Ipsec inspection has also been setup on a global policy, but the user still cannot pass traffice to the remote VPN he is connected through.
At the Main Office we have an ASA 5510 that terminates a site to site VPN, allows remote connections with PAT and allows passthrough no problems. Any ideas?

I am having a simuliar issue with my ASA 5505 that I have set up. I am trying to VPN into the Office. I have no problem accessing the Office network when I am on the internet without the ASA 5505. After I installed the 5505, and there is internet access, I try to connect to the Office network without success. The VPN connects with the following error.
3 Dec 31 2007 05:30:00 305006 xxx.xx.114.97
regular translation creation failed for protocol 50 src inside:192.168.1.9 dst outside:xxx.xx.114.97
HELP?

Problem with Virtual PC and Network Connection - VPC gets disconnected

Hi,
I've been having a few problems with a virtual computer and its network connection. I've set up a few computers the same way over the years and they all work fine except this one. We use the Virtual PC and XP mode to access our data from an older
program. The databases are on a server, which are accessed as a mapped drive. Every once in a while (with no particular pattern, sometimes it doesn't happen all day, sometimes it happens every 5 mins), the VPC gets disconnected from the network,
my program returns a file read error and then everything is frozen. When I try to ipconfig/release and renew, it releases correctly then it won't renew. I need to shut down the VPC from the Win7 task manager and even so, it doesn't shut it down,
even when I try to kill the vpc process. The only way it'll come back up is if I restart the computer. The network connection on the Win7 computer doesn't do that.
Is there anything I can do to fix this ?
Thanks,
Melanie

Hi,
Does it become more stable now, actually, I'm afraid that this issue is not related with the drive letter or name. Since you're using bridge mode, the I would suggest you use NAT as a test, it is the default network configuration, which allows the VM
to leverage the external TCP/IP network connected to the host. This is very useful if you regularly move the host computer between different network configurations. NAT is the preferred networking option when there is a shortage of IP addresses, a need to
ensure the VM’s IP address is not targetable from an external network, or a need for connecting using WWAN.
Yolanda Zhu
TechNet Community Support

Problems with VPN-Client 5.0 instoled on Windows Vista over ADSL Conecction

Hi, I have severals clients that they use Windows Vista and connects throw there lan over a VPN-Client. The clients that has an ADSL connection in there hose has disconect problems. Do you know why?? Do you know same workarround to do?? Thanks.
Regards.

Make sure that you have the right cable pinout and that your ISP has turned on the DSL service. Troubleshoot the DSL connection by watching the modem state of the ADSL interface as the line retrains.
To use the VPN Client, you need
- Direct network connection (cable or DSL modem and network adapter/interface card), or
- Internal or external modem
For further more troubleshoot click this link,
http://www.cisco.com/en/US/docs/security/vpn_client/cisco_vpn_client/vpn_client500_501/release/notes/51client.html#wp1550392

Complex Problem with Time Capsule and Network

I have setup an airport network based on a 500 gb Time Capsule which for about a year was working perfectly. Last days some problems came up. The network is shared to 2 different macbooks pro. The first macbook pro works perfectly, the internet connection is stable and fast. The other macbook works weird: Although it finds the network the internet speed is very slow and not stable. Also it can't backup on the time capsule as it used to do (msg: can't find the server). Ι have the same network settings for both the macbooks pro and I had several times restart and reset the time capsule.
Thanks in Advance
Costas

I suspect that you are using someone else's airport connection. That would let you access the internet, but not access your file server. go to the airport menu and make sure that you are using your airport connection.
If that does not work, does everything work well when the computer is within a few feet of the time capsule?

WiFi problem with iOS 6 and network login screen

Here is a detail problem description:
Equipment: iPad 3 with iOS 6
Environment: corporate network with a login screen that requires login every 24 hours.
What happens: The very first time I tried to login into the network everything worked fine. The login screen showed up (as always did with iOS 5) as expected. But, the login screen does NOT come after 24 hours (when re-login is required), unless I will reboot the iPad (using the 2 buttons), or I will reset the network settings (which again does a reboot). Switching on-off the WiFi, or any other remedy does NOT work.
The problem is not related to the network or the particular iPad or iPhone. All iPads and iPhones with iOS 5.2 or earlier work just fine. Only the ones with iOS 6 have this issue.
I would appreciate any creative idea to resolve the issue. Thank you.

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Problem with HP printer and Network

I recently purchased a MacBook Pro and HP 8600 wireless printer. I'm using an airport extreme base station.
I'm having trouble with network connectivity and wondered if the printer is the culprit--many times after printing, I lose my network connection completely.
I've tried updating base station software, computer software updates, re-booting the base station, etc., but nothing seems to permanently solve the problem.
Would appreciate any insights.
Thanks

Sounds like this could be an issue with the software. To start I want to be sure that we remove the software fully and correcty before we continue. Follow the instructions below and see what happens after.
First if you use a USB cord, make sure to remove it (this is important). Do not plug it back in until the software directs you to. Then go through the Devices and Printers, Programs and Features and Device Manager folders and insure that all copies, files, and programs related to the printer are removed. Then as directed, restart the computer.
In the START menu type "%temp%" and press ENTER. Here I want you to press Ctrl+A and hit DELETE. Some of the files will not allow you to delete them, skip those files and delete the majority that allows it.
find and install the FULL FEATURE SOFTWARE if it is available :
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=3692888
Install that and let me know the result!
Have a great day!
-Spencer
PS have a wonderful day and a fantastic weekend!

Problems with text messages and internet access

I have an Apple 5c and over the last few weeks my text messages to most people had not been completing the send. Now, in addition, I am not receiving most messages and I can't access the internet for most apps (like maps, yahoo search, youtube). Is anyone else having this problem? Does anyone have any suggestions as to why this is happening and how to go about fixing it?

Try removing then reinserting the SIM card -
SIM Card Inserting Removing Apple iPhone 5 | Verizon Wireless
It may just need a refresh to reconnect to the network again.

NLS_LANG with Instant Client and MS Access

Hello Everybody.
Recently I downloaded Oracle Instant Client 10.1.0.3. I made a custom instalation for my little Access (ODBC)application.
In the begining the installation had not any other configuration than PATH Environment variable and ODBC basic DLL paramaters. That configuration worked very well for some minutes, until I realized that some rows in my linked tables appeared as #DELETED.
I made a little web-based investigation on the Microsoft and Oracle web site and I arrived to the NLS_LANG parameter. I realized it was my problem because I have Latin American characters in my rows and those rows were the "#DELETED" row I saw in my tables.
I did "select * from NLS_DATABASE_PARAMETERS" and that command showed AMERICAN and WE8DEC as NLS_CHARACTERSET.
I set the NLS_LANG=AMERICAN_AMERICA.WE8ISO8859P1 and the problem disapeared.
My question is: Is that the correct configuration in this case?
PD:I'am using Win XP Pro in Spanish.
Thanks

Hi,
>>then I use Oracle Instant Client
It's possible that maybe a NLS environment variables configuration problem ... For more information, I advise you to take a look at [url http://www.oracle.com/technology/tech/globalization/htdocs/nls_lang%20faq.htm] NLS_LANG FAQ
Cheers
Legatti

Problem with masked SSID and network connect

I recently purchased, and am discussing the HP Photosmart 6510 All in one product.
I have read, and verified that your product does not permit connection to masked (non broadcast) SSID networks.
I would appreciate you making a software change to support masked SSID networks. It seems unreasonable for me to be forced to lesson my security (it's hard to attack or connect if you don't know it is there) posture to enable wireless printing. The printer software allows you to enter an network SSID manually, so the only change needed is to enable connection to a masked SSID in the same way that a computer, or a gaming console (WII) does.
Masking the SSID is a standard bit of functionality for network routers, so much so that every device (smart phones, gaming consoles and laptops) that I have connected all support the recognition and connection to a manually entered, masked SSID.
Your software/firmware should support all standard functionality for wireless use if it is advertised as a wireless device.

Let's try again. I wasn't asking for anyone's opinion regarding the efficacy of using a standard, provided bit of Wireless network functionality. It would be a mistake to assume that this is the only security method I employ, but masking simply makes it so that the other 3 networks on my block are the ones with a "welcome sign" out.
ALL my other network supporting appliances support SSID masking.
When will you change the software/firmware to support this standard feature (regardless of how you feel about it)?

Problem with VPN Client and network access

Similar Messages

Maybe you are looking for