Problems connecting to cRIO-9024 in MAX

Hello,
I can't see my cRIO in MAX. I have followed instructions on other guides but to no avail. I am using windows 7, LabVIEW 2012, MAX 5.5, I have to latest NI-RIO installed (NI-RIO 13). The cRIO has the correct setup, the status light is flashing 3 times etc.
It is probable something very small and basic that I have missed, any help would be much appreciated.
Thanks in advance,
Chris

I have both of those installed, and I jave RT and FPGA installed also.
I have reinstalled RIO just now to ensure that it was the last instulation and that all drivers were connecting but it still is not showing up.
Attachments:
Software MAX capture.PNG ‏56 KB

Similar Messages

Unnable to connect with crio via project explorer

Hello
I'm having problems connecting the CRIO-9073 via the project explorer.
I can see my crio in my project, but when I try to connect, it deploys for 5 seconds, then I get the message 'failed to connect to target'.
I can connect the crio within NI MAX, I configured the network settings with static IP.
I can also ping the crio via the command prompt, I have labview realtime module installed.
I also did a disk format on the crio and reinstalled all the software on the crio.
Do I need other software? Or anybody other ideas.
In the attachements you can find the error message and the list of software installed on my host pc and crio.
Thanks!

thank you for fast answer
Yes checked the whole list of software to install on the crio.
As i'm not sure with software I need on the crio I didn't remove any software (I'm new to labview).
I first added it 'automaticly' , but also tried it by adding it manually and enter the IP.
Both didn't work and gave me the same error message.
Yes Im connecting with the explorer while MAX is open and connected with the CRIO

Using cRIO-9024 serail port can I read the data from AFM60 absolute encoder, multiturn, SSI interface

I would like to request you to kindly address the following quarries.
1. Using cRIO-9024 serial port, can I read or write data from AFM60 absolute encoder, multi-turn, SSI interface (please see the attachment for detail information about the encoder)?
2. Which type of encoder interface (SSI, TTL/HTL) is compatible with the serial port connection of cRIO-9024 controller?
3. Are there any limitation on choosing the output frequency and resolution (pulses per step) of the encoder? If the answer are yes, what are the suitable ranges of frequency and resolution?
Looking forward to your kind reply. Thanking you.
Regards
Shantanu
Attachments:
afs60_afm60_english.pdf ‏2298 KB

Hi Shantanu,
To read and write data from the serial port on a cRIO you access the serial port as a VISA resource, there are serial VISA VIs to read and write data on the serial port.
If you look under the Hardware Input and Output folder in the NI Example Finder, you should find a Serial folder, this contains examples for serial communication.
The serial interfaces on cRIO devices use the RS232 standard, unfortunately as SSI is based on the RS422 standard, you won't be able to directly interface the encoder to the serial port as they are not compatible. You would have to either use a separate interface between the devices or use a digital input module in your cRIO to directly process the encoder data.
To answer your question about frequency, the maximum baud rate for the serial port on the 9072 as listed here is 115200 bps, so this would be the maximum raw data transfer rate for any connected device, the number of steps for your particular encoder is limited by the maximum shaft speed as detailed in its specification.
I hope this is helpful to you, feel free to ask further questions and I'll do my best to answer them.
Regards,
Adam Brown
Applications Engineer
National Instruments UK

Problem connecting cRIO-9072 to the computer

We have to connect the cRIO-9072 to the computer remotely through a wireless medium. We have a fixed and dedicated IP address so that the network connected to the computer can talk to the cRIO in the remote location wirelessly. However, we are unable to connect the cRIO to the computer. There is no problem in connecting the cRIO to the computer through Ehternet cable physcially but when made wireless the computer no longer recongnises the cRIO.
What could be the solution to this issue ?

Hi rarun7,
If your cRIO is on a different subnet than your computer, there can be a few issues in connecting to it. I would recommend ensuring that the subnets match on both the computer and the cRIO. If your cRIO is still not showing up in Measurement and Automation Explorer (NI MAX) after the subnets match, please refer to the document I have provided below. Hopefully, some of the suggestions in the document will allow you to achieve a connection!
Why Does My CompactRIO Controller or Single-Board RIO Not Show Up in Measurement & Automation Explor...
| Zach J. | Applications Engineer | National Instruments |

There was a problem connecting to the server "Max Time Capsule"

Disclaimer: Previously posted here (Ask Different) and similar to this.
I'm trying to use my MBP inside and outside my office, and having it backup to my 2TB Time Capsule when on its wireless network, or defer backups when not on the Time Capsule's wireless network.
Unfortunately, if I've been on a different wireless network for a few hours worth of backup attempts, bringing the machine back onto the Time Capsule's wireless network doesn't resume backups, and Time Machine never recovers. I can select the disk as a backup drive in the Time Machine preferences, but the disk remains unavailable from the Finder, and any backup attempts yield the standard:
There was a problem connecting to the server "Max Time Capsule"
Check the server name or IP address, and then try again. If you continue to have problems, contact your system administrator.
My WiFi connection is through the same Time Capsule that hosts the backup drive, and its name and IP address have decidedly not changed. The only thing that seems to help is restarting the Time Capsule, but that is an inconvenient workaround at best.
The problem sounds similar to Backup Disk Not Available, but the answers to that question are either to restart or change the disk name or turn off the 5 GHz network (which didn't help). I also looked at /Library/Preferences/com.apple.TimeCapsule.plist, but found nothing that seemed relevant.
Any suggestions would be greatly appreciated. My MBP is running OS X 10.7.5, and the Time Capsule firmware is 7.6.1.

There was a problem connecting to the server "Airport Time Capsule".
The server may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again.
I still have internet connection, and have tried other suggestions across internet but really the only fix has been to power cycle the ATC. This unfortunately is only a temporary remedy for a day or so until it returns.
Any suggestions on how to fix this problem?
There is no fix.. I have written a bunch of suggestions to try.
https://discussions.apple.com/thread/6106750?tstart=0
It is very common on Mavericks.
How long did it take from when you set it up till it went bad??

Crio 9024 NI 9403

Hello all,
im trying to program an NI 9403 using labview and crio9024, but first of all i should delete priviously simulated hardwares. but it's somehow impossible caz i can't see these devices in the configuration tab (refer to the attached photo plz), can sb help plz ?
while running the program I get the following error, although the software is installed
Error Code: -63040
NI-RIO: (Hex 0xFFFF09C0) A connection could not be established to the specified remote device. Ensure that the device is on and accessible over the network, that NI-RIO software is installed, and that the RIO server is running and properly configured.
Thanks
Attachments:
MAX.jpg ‏46 KB
distribution system manager.jpg ‏29 KB

Hello AutonomusMode,
this is normal that no moduls are shown on a cRIO system in MAX.
You can see the moduls in your LV project explorer.
What LV Version is in use and in which VI the error happend?
Can you post your project?
Attached a little example project.
dublicate post on this web site
crio 9024-URGENT!
MAX
crio 9024 NI 9403
NI 9403 using FPGA as an input module help?
best regards
Alexander Glasner
AE NIE
Attachments:
9024.zip ‏37 KB

VeriStand 2013 Embedded Data Logger with cRIO 9024

I am using VeriStand 2013 with the Embedded Data Logger on a cRIO 9024. I have noticed that when I first deploy after a complete power cycle, the embedded logger works great - responding immediately to a change in the Log Trigger value. However, If I undeploy and then redeploy the project, the embedded data logger appear to casue issues in the communication between the target and the host. The first symptom of this is that the indicators on the workspace appear to begin to lag significantly. The also affect the response of the boolean control that I have for the log trigger which now will not actually turn off when pushed but will rather only respond many seconds or minutes later. When this happens, the log files are also much longer than the intended period.
This problem only gets worse with further undeploy and reploys. However, when I power cycle the cRIO, the net time i open the workspace everything is working great again with no delays.
Any ideas on what could be causing this issue?

Hello Aaron_Smith,
Are you writing to a single file each time? If so then the issue could arise from the file size and the file needing to be loaded into memory each time your redeploy. Try to run the system so that it writes to different files. Also, what is the status of the memory and CPU usage of the device while the application is deployed? Please verify that you are not maxing out the processor or memory as this causes network issues that could result in behavior of this type. Also, would it be possible for you to post a simple example that exhibits the same issue? Please include all files that are necessary to run the system definition.
Wear
National Instruments
Product Support Engineer

SharePoint - Error_1_Error occurred in deployment step 'Add Solution': Timeout expired. The timeout period elapsed prior to obtaining a connection from the pool. This may have occurred because all pooled connections were in use and max pool size was rea

Hi,
I am Shanmugavel, SharePoint developer,
I am facing the below SharePoint 2013 deployment issue while deploying using VS2012.
If i will deploy the same wsp or existing wsp
(last build) using direct powershell deployment, the solution adding properly, but the same timeout exception coming while activation the features. Please find the below error.
I tried the below activists:
1. Restarted my dev server, DB server.
2. tried the same solution id different server
3. tried existing wsp file (last build version)
4. Deactivated all the features, including project Active deployment configuration.... but still i am facing the same issue.
I hope this is not coding level issue, because still my code is not start running, before that some problem coming.
Please help me any one..... Last two days i am struck because of this...

What you need to understand is the installation of a WSP does not do much. It just makes sure that you relevant solution files are deployed to the SharePoint farm.
Next comes the point when you activate the features. It is when the code which you have written to "Activate" certain features for your custom solution.
Regarding the error you are getting, it typically means that you have more connections (default is I guess 100) open for a SQL database then you are allowed to.
If you have a custom database and you are opening a connection, make sure you close it as well.
Look at the similar discussion here:
The timeout period elapsed prior to obtaining a connection from the pool. This may have occurred because all pooled connections were in use and max pool
size was reached[^]
I would suggest further to look at the
ULS logs[^] to get better insight.
Manas Bhardwaj's Stream : www.manasbhardwaj.net

Choosing the Right Network Protocol for CRIO 9024 to PXI over Ethernet

We are in the design phase of setting up a CRIO 9024 Embedded Controller to send data captured to a PXIe-8105 Controller over ethernet. The data will be be 2D arrays of double precision. This data will need to be sent to the pxi at the end of each test step. Each step will have different number of channels and sample rates.
For example, Test Step 1 will have 5 channels of Analog inputs that will be sampled at 100,000 KHz for 1 second. This data will be coming from the CRIO FPGA. The data will get post processed by the CRIO 9024 and analyzed for pass or fail metrics. Then, the CRIO controller will send the 2D Array of Data (500,000 data points 5 X 100,000) and the results of all the metrics (a 1D array) to the PXI.
The connection to the PXI will be using Ethernet.
Keep in mind that the PXI will also have to send the CRIO some values to tell the CRIO when to start the test and when the test sequence is complete.
I was thinking TCP/IP would work best because of the 2 way communication needed. But then I was looking at Network Streaming or even using Shared Variables.
If anyone has any ideas or suggestions please please post them.
Spark
CLAD
Test Engineer
Solved!
Go to Solution.

Hi,
You could use either. Whichever you are more comfortable with really. The STM method will have slightly less overhead over my XML style of tagging the data but it will be very little given the data size. Probably go with STM as it just has most of the work done for you.
In terms of data size the way you should normally transfer data like this is to flatten to string. If you convert to a string of human readable numbers you will either lose precision, increase size or both. Given that, the string after being flattened will be the same size as the original array anyway so quick calculation based on your previous post 500,000 doubles (8 bytes) is 4 miB (3.8MB)
Cheers,
James Mc
========
CLA and cRIO Fanatic
wiresmithtech.com/blog

NI 9223 at 1Mhz on a cRIO-9024

Hi All,
I'm trying to use the 9223 module to sample at 1Mhz using User-Controlled IO Sampling.
The 9223 should be able to simultaneously sample 4 channels at 1Mhz (that's why I bought it), but I can't get it above 500khz.
I'm using the "NI 9223 User-Controlled IO Sampling" code from the LabView examples (see attached), which works fine with a sampling period of 2 uSec or above, but at 1uSec I get the attached error.
The example code has a warning saying some cRIO controllers can't keep up with 1Mhz rate of the NI 9223. I'm using a cRIO-9024, but I can't find the relevant specs on sampling at 1Mhz for it. Could this be the problem? This cRIO/module combo was recommended to me by a NI rep with one of my requirements being sampling at 1Mhz, so I hope that's not it...
Anything else I can do to get it to run at 1Mhz (or at least at 750khz)?
Thanks!
Attachments:
NI 9223 User-Controlled IO Sampling (Host).vi ‏259 KB
NI 9223 User-Controlled IO Sampling (FPGA).vi ‏128 KB
NI 9233 error msg.png ‏18 KB

Sorry for the late reply. I decided to install LabView 2013 since the code has obvioulsy changed between versions and I hoped it might solve my problems.
In short, the 2013 host code is also different than the 2011 example code. The 2013 code actually works at 1Mhz. However, it does not graph the data continuously. The 2011 code has the graph inside the while loop, while the 2013 code displays it after it acquired all of the samples (outside of the while loop). The number of samples that it can acquire is limited.
In my application I'll be running code on the FPGA at 1Mhz. It will control a voltage output based on input idependent of the host. However, I also need a continuous display of the data on the host and the ability to data log a couple of seconds at a time at the press of a button. This host code is all working, but times out at the 1Mhz that is required to run the FPGA code.
What I am now considering is putting two versions of the FIFO code on the FPGA. One running in a different loop that runs slower that is used to display the data continously and another one that runs at 1Mhz for data logging that will only gets called occasionally and does not need to be continuous.
I'm not completely happy with that solution however, because I'm used to pausing the graph at will to inspect the data and it will mean rewriting of some code.
I've attached the 2013 FPGA example code and 2011 Host example code. Ideally these would work together at 1Mhz (right now it times out at 76 ticks). Any ideas how to get this to work would be greatly appreciated!
Thanks in advance!
Attachments:
2011 Host code.png ‏60 KB
2013 FPGA code.png ‏85 KB

Access deployed project on cRIO-9024

I think this is a fairly simple question, but I just can't find the answer anywhere. Is there a way to access the project that was most recently deployed onto the cRIO-9024 and open that file into LabVIEW? The problem I am having is that the computer where all the code is developed and saved is not the one used during experiments in my lab where the software and hardware is actually needed, and I am hoping there is an easier way to get to the files than just having to copy them all over to the other computer every time I make changes. I'm guessing there is one really simple thing I need to do that I just don't know about, so any help would be appreciated.
Thanks,
Megan

Hi Megan,
If you are referring to a deployed executable, you cannot open that in LabVIEW. When the executable is built, the block diagram is stripped and turned into lower level code, so that is unfortunately no longer accessible.
Jayme W.
Applications Engineer
National Instruments

Error on RT Get CPU Load With CRIO 9024 and LV2010

I just try to monitor CPU Load on my CRIO 9024 using LV2010 and i get Error -2233 with RT Get CPU Load.vi
It worked with LV2009 and not anymore ... Someone has some issues ?
Could we enabled/disabled CPU load on target ? how ?

Hi silencer,
Thank you for posting on National Instruments' forum.
Can you tell me your version of LabVIEW RT, and NI-RIO drivers please?
I verified the problem with LabVIEW 2010 and a cRIO 9022 and it works.
Can you send another screenshot please?
Best Regards,
Romain P.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
>> NIDays 2011, le mardi 8 février au CNIT de Paris La Défense

Time Capsule: Problem connecting to the Server

Specs:
MacBook Pro (Retina, 15, Late 2013), 2.6 Ghz Intel Core i7, 16GB 1600 MHz DDR3, NVIDIA GeForce GT 750M 2048MB, 1TB SSD, OSX Mavericks 10.9.4 (13E28)
Time Capsule 2013, 3TB, Firmware 7.7.3
"There was a problem connecting to the server "Xxxxx's Airport Time Capsule".
Check the server name or IP address, and then try again. If you continue to have problems, contact your system administrator."
I can access my Time Machine, but I cannot backup. Everytime I try to I get the above message. I had this problem in the past, but opening Time Machine System Preferences and Selecting and deselecting the current disk seemed to fix it. It was an odd fix, but every time I went into the settings to get to the bottom of the problem it resolved itself before I could get to the bottom of the issue. I thought I was imagining it at times! The Time Capsule is also giving my network sporadic connectivity issues to the internet. It will maintain a perfect wireless connection, but not provide a connection to the internet. Turning my notebooks WiFi on and off seems to resolve the issue upon reconnection.
What's going on and how do I fix it!
I also have AppleCare for the Time Capsule and would like to not get too crazy or involved with the solutions. Nothing that voids the warranty!

We would not suggest warranty voiding fixes on any device that has warranty.. we only suggest those when Apple refuse to help or the device is older.
Reset your TC to factory.
The Factory Reset universal
Unplug your TC/AE. Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. The time is not important.. it is the front LED rapid flashing that indicates you are in factory mode.
Release reset.
If it doesn’t flash rapidly you have released reset at some point and try again.
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Redo the setup of the TC.. using all short names.. with no spaces and pure alphanumeric.
Apple changed Mavericks default network protocol to SMB and it has tighter rules.
eg.. A good name is TCgen5
A good name for the wireless is TCwifi
Use whatever you like.. up to max 20 characters but short and sweet is better.
Once you do that, mount the disk in finder manually.
Go, Connect to server.. From the top menu area.
AFP://TCgen5.local
OR even better use its IP address.
AFP://10.0.1.1 (but it must be static which usually means in router mode).
Once you have found the network resource.. put in your disk password and save it to the keychain. All passwords should be pure alphanumeric mix of case and numbers and 10-20 characters.
Reset Time Machine to the new path to the TC.
It will say it will start a new backup but in fact it will discover the old one and simply continue the backup.
If it still fails.. it is faulty and should be returned.
The drop out of the internet even when wireless is working points to faulty WAN connection which is a serious bug on these.

I'm trying to set up my Ipod, but when I go to sign in with an apple ID it says 'Could not sign in: there was a problem connecting to the server'.

I just bought a 3rd generation ipod touch. It was professionally refurbished. I'm trying to set it up, and everything seems to be working fine, until we get to the wifi. I live on campus and our wifi is username and password protected. I signed in and everything seemed to work fine, and in the top left hand corner I have all the bars for wifi. However, when I go to sign in with an apple ID it says 'Could no sign in: there was a problem connecting to the server'. I've tried turning it on and off again, tried signing on to our wifi again, but it all isn't working. What can I do?

I also encountered the same problem. Try using a different email address or try signing in later.

I am having problems connecting to home wifi. It was working, but now all I get is a blank white screen. I re-booted with no success.

I am having problems connecting to home wifi. It was working, but now all I get is a blank white screen. I re-booted with no success.

Hi, blank white screen where exactly?
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.5, 10.6, 10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x/10.8.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6/10.7/10.8, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
(There may be better or faster DNS numbers in your area, but these should be a good test).
Click OK.

Problems connecting to cRIO-9024 in MAX

Similar Messages

Maybe you are looking for