Process contract screen error

Hi,
We are in SRM 5.0 version. When we go for process contract screen. A default value is present over there. Even after deleting the value when a number is entered. It appends with the default value resulting in no results found.
Example
Contract number default values comes rty
when it is deleted and entered 457
systems appends with rty;457 resulting in no results found.
Please advise on this issue.
Regards,
Basha

Hi,
as i understood that we need to specify the source system name / name give for your source system in SM59.
regards,
Vishwa

Similar Messages

Windows Blue Screen Error Message Appears As Soon As IPod Connected

Everytime I connect my IPod to my computer, I get the Windows Blue Screen error message. Thought it was the cable, so plugged cable in by itself. No problem. Uninstalled IPod and ITunes software and then plugged in IPod, still got the Blue Screen. The Blue Screen says something about "recent plugged in device problem". It is not the cable, it must be the IPod. Did not have this problem when I bought it. Tried it on labtop and get the same error message. I can't do updater or anything that requires me to plug the IPod into a computer because the Blue Screen appears immediately. When I unplug, the Blue Screen remains and locks up the computer so I have to restart each time. I have tried everything I can think of. Please help.

Hi Mike thank you for replying,
I am not able to start the computer in safe mode, safe mode with networking, last good known configuration etc, Each time it quickly blue screens and restarts about two secs into the process.
I was unable to try a clean OS install from the disk as it gave the blue screen error shown in the original post. The same thing happened when I tried to use the repair option on the XP home disc. So i can't get into the computer at all to start diagnosing the fault, the only clue I have is the error message, and after searching the internet I haven't found much enlightenment from that yet.
If you can help me out or suggest where to search it would be much appreciated.
Thx

Blue screen error message on Satellite Pro A10

Hi,
I'm trying to help my inlaws with their Satellite Pro SPA10. I had set this up for them a few months ago and it was running really well.
Now it restarts about two seconds past the "use last good configuration" etc. screen, gets to this screen again then restarts immediately ad infinitum, never pausing on the error mesage for long enough to see what it says.
I managed to get it to boot from the windows XP home disc and got as far as the repair or continue with installation screen. When I asked the computer to do either it crashes to blue screen almost immediately. The error message is
*** STOP: 0x000000c5 (0x00000000, 0x00000002, 0x00000001, 0x8082B98B)
This is beyond my level of expertise, can anyone help?
Thanks

Hi Mike thank you for replying,
I am not able to start the computer in safe mode, safe mode with networking, last good known configuration etc, Each time it quickly blue screens and restarts about two secs into the process.
I was unable to try a clean OS install from the disk as it gave the blue screen error shown in the original post. The same thing happened when I tried to use the repair option on the XP home disc. So i can't get into the computer at all to start diagnosing the fault, the only clue I have is the error message, and after searching the internet I haven't found much enlightenment from that yet.
If you can help me out or suggest where to search it would be much appreciated.
Thx

Blue Screen error using Boot Camp when installing XP on the MacBook Pro

I have been trying to install Windows XP Professional (with SP2) on my MacBook and I keep encountering blue screen errors during the install. I successfully create the Windows partition with Boot Camp (v2.0) and then Windows install begins. However, during the setup process it hangs and then eventually throws an error showing a blue screen. There has been a different error each time I've tried to install. I've booted in OSX and then deleted the Windows partition through Boot Camp and then attempted the process from the beginning five separate times and each time I get an error during the initial install phase.
Its not a matter of the installation CD because i borrowed 3 differnt copies from some friends and i still have the same issues.
Once, I managed to actually start windows XP however it was full of errors probably as parts of it weren't properly installed due to the the blue screens that made me reboot several times.
Am I the only one having this problem??
Is this a matter of the hardware? Can you think of any possible solution?
(I used NTFS did everything propperly I'm 100% sure)(I tried FAT as well)(still nothing)
PLEASE HELP

Can you read and write from your optical drive? I would have it checked by burning something to it and seeing if it can be read.
I have noted a link, with some information that may be helpful, for you to check out.
http://discussions.apple.com/message.jspa?messageID=7872477#7872477
I would repair permissions before your next attempt too.
If this fails, I would contact Apple.

Blue Screen error message after using Rescue and Recovery.

Good morning - I unfortunately had to use the IBM Rescue and Recovery feature to restore my factory settings. However, now my computer is giving me a blue screen error during the startup process. Unfortunately it is not on the screen long enough for me to get too much information from it, but I have been able to get win22n51.sys as being some sort of error message. If I start the computer in safe mode it will load without the error. If I use the safe mode plus networking it gives the error. So I'm assuming it has something to do with the network drivers?
I would appreciate any ideas you all have for resolving/further diagnosing this problem.
Thank you!

Hello,
Perhaps this Lenovo knowledgebase article, "XP Crash: System may hang or restart with a previous version of the Intel PRO 2200BG Mini PCI adapte..." will be of help to you in resolving the problem?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Hp pavillion a1324n - blue screen error

After an extended shut off period (say overnight), when I start up my desktop it goes through the process and starts up fine but within a minute it shuts off and either it restarts and and then works fine for the rest of the day (even if I shut it off and turn it on several times) or it goes to a blue screen error and I have to restart it manually with the power button and then it restarts and works fine after it is restarted. However, the next time I shut it off and leave it off for a long period of time, it then goes through this blue screen or restart process? Please help me with suggestions as to what may be causing this issue and how it may be fixed. Thanks.

You've got an older PC so clean out the dust bunnies inside... just to be sure.
HP released a BIOS update that address lock ups and freezes... might be related to the problem. http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=pv-51922-1
... an HP employee expressing his own opinion.
Please post rather than send me a Message. It's good for the community and I might not be able to get back quickly. - Thank you.

Blue Screen Error after Synching

I had Blackberry Desktop Manager 7 installed on my WIndows XP machine...I have been getting Blue screen errors frequently after my Outlook is synched wiht the device..I was on BDM 6 prior to this and used to consistently get Blue Screen Errors. I used to think there was some other issue with the laptop until recently when I got a new one and I installed The desktop manager.
Once i realised that, I uninstalled the Software from my desktop yesterday but I read a lot of blogs that said that the BSOD will continue to come as your normal uninstalls are incomplete..Could you let me know how this can be fixed? Do you have a stable version of the desktop manger that doesnt give a BSOD?
I need to sync my device with Outlook everyday..and I cannot afford BSOD's everyday..

Hi and Welcome to the Community!
I suggest this thread:
http://supportforums.blackberry.com/t5/Desktop-Software-for-PC/Cleanly-quot-Starting-Over-quot-with-...
It starts with a process for cleanly starting over, and there is some discussion, and there is also a post (15) with links to older Desktop Software versions, if those are needed. Note that this is not, by any means, guaranteed to work...but it has worked for many to resolve issues they are having.
BSOD's are actually more rare of a problem, from what I've seen, and often indicate something more core wrong with the actual PC, Windows installation, or something else...and the RIM Desktop Software is simply revealing this deeper flaw rather than being the cause of it. In the worst case scenarios, I've actually heard of folks doing a clean rebuild of their PC (e.g., reinstalling Windows from scratch) and that rectifying the problem.
Ohhh...one last thing:
jinugeorge wrote:
Do you have a stable version of the desktop manger that doesnt give a BSOD?
FYI -- From the wording, I suspect you are misunderstanding the purpose of these forums. This is a user-to-user community, not a user-to/from-RIM channel for any communication whatsoever. So, by "Do You", you are actually asking that of other users, "out there", just like you who happen to be volunteering time to help others out.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

HT201413 i tryed to restore my phone but it turns of during the process and an error happens so what should i do

i tryed to restore my phone but it turn off during the process and an error happens so should i do ?

Hello there, VladlsSwag.
The following Knowledge Base article provides some steps for troubleshooting your issue:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Particularly:
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
My issue is still not resolved. What do I do next?
Contact Apple Support.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Error in module program - Invalid field format( screen error )

In the module program i have added 1 input field named gv_pallet of 1 character. while processing the transaction when i put value 1 in this input field and press a button i am getting error ' Invalid field format( screen error ) .
I am not geting any clue whats the eror . can anyone able to tell me the error.
Point will be guranted .
Regards

No need to loop to check whether data is changed after PBO, just check System Field SY-DATAR, it will be set to 'X' if any field was changed.
So the following code is enough;
IF SY-DATAR EQ 'X'.
PERFORM SAVE_DATA.
ENDIF.
Regards
Karthik D

Invalid field format (screen error)

We are using custom module pool report for displaying information. Information display in Table control which has also Radio button option for the further processing. After unicode conversion we are getting error while accessing the screen as "Invalid field format (screen error)" when user select Radio button. In production environment we are not facing any issue, but in Dev + Qas we have this issue. Nothing is changed as all environment are sync. To solve the issue we re-defined the Radion screen element, but no success we are still getting same error. I am not sure whether it is related to Page Format or something else. Could you please let me know whether anybody faced this issue ? For the information, I already searched on SDN and SNote, but there is no post or SNote

Have you checked if there are overlapping fields on the screen.
I've seen simular errors and usually it was beacuse of some change by SAP that made it so that the defined length of the screen field was suddenly to small.
I'm not saying that this is the case in your situation, but it never hurts to try and change the length of your screen field and see if that resolves the issue.
Arthur

Disable Change Icon in Process Contract

Hi,
Is it possible to Gray out or Disable the Change Icon in the 'Process Contract' page via BADI? The only way I know how to gray out or disable it is by customizing the Template.

Hi,
You can use the BADI "BBP_UI_CONTROL_BADI" to change the screen appearance in SRM e.g Enabling/disabling icons /buttons,graying out/hiding fields etc.Also,Checking documentation on the badi, it is avaible for:
Purchase contract and global outline agreement(Filter value BUS2000113)
Bid invitation (Filter value BUS2200)
Bid (Filterwert BUS2202)
Auction (Filter value BUS2208)
Purchase order (Filter value BUS2201)
Purchaser's Sourcing application
Confirmation (Filter value BUS2203)
Invoice (Filter value BUS2205)
Vendor list
To use this BADI,you just need to know the name of the field/icon in the screen and acc set its display propery parameter in the BADI.
For sample code of this BADI,refer the foll link:
Re: Grey out / Display fields in BBPIV02 transaction
HTH.
BR,
Disha.
Pls reward points for useful answers.

Search Help error : Invalid field format Screen error

Hi All,
I have attached a search help to contract field for contract no and item number. (in my own screen developed in a report)
The search help picks up data and assigns it to the fields,
But after this when I click on any other button, I get error saying :
Invalid Field Format (Screen Error) !!!
Any pointers guys !!!
Warm Regards,
Girish

screen checks in abapautomatically checks for format of field when u enter data....i.e date, integer etc...the problem in this case is that when u seelct a value using the help it is filling a value which is not the correct format...so check for the data types and test it again...this is definitely the problem.

Blue screen errors - critical updates - XP SP2 SP3 - device drivers

We initially had an internal program error on an XP program that caused it to quit running. We
started getting blue screen errors that I could not resolve.
(painfully) I reinstalled XP sp2 after:
removing the boot partition, ran delux tools (complete) with not errors, repartitioned boot camp
(the long way), reformated the windows partition, (long way).
I went back and forth getting the windows and apple updates after installing XP until it said I only
needed SP3, which I was not yet ready to go to.
I still got errors and crashes, even with no applications running except Norton antivirus (only).
I left the unit on over night and had 24 save dumps in the event viewer. I checked for win updates
again and express said only sp 3 was available. I decided tocheck for custom updates.
Custom told me there were 102 critical updates. I tried to install them. They all downloaded but
98 of them would not install.
I convinced myself I had done something wrong and repeated the process with the same result.
In that the updates would not install, did I really need them or was boot camp/windows misinformed?
I installed sp 3. (boot camp 2.1) Seems to be running OK but with some errors in the eventvwr and
some more crashes.
I compared with another unit and could not replicate the errors. The other unit (same setup) had two user accts. while my broken set up had one that came up right away with reboots.
I added a second user and the crashes (though not all eventvwr errors) went away. Is this another
boot camp/windows xp issue?
I wanted to know how to find which device drivers and which versions I am running. That seems to
relate more directly to blue screen errors if they return.
Thanks,
-um

Hi and welcome to Discussions,
sorry to hear about such a misery.
Sadly Windows XP does not offer such a 'list' of hardware components and associated drivers.
Only way is to use the Device Manager (from Control Panel - System - Hardware) and click through the components to find out which driver version is used.
On a personal sidenote: I would stay away from any kind of Norton products either in Windows and/or OS X.
Searching around in these Forum you will find numerous mentions of problems with Norton products running.
Good Luck
Stefan

"Not enough storage is available to process this command" error in RDP login

I agree with disabling SSL3 but the TLS ciphers are unaffected and may be causing you issues.

Out of the blue I got the error message in the rdp connection like "server not found" The server is windows server 2012. It was also not working properly, Although the server hosting became right after half a day,before there was only the main domain was working, sub domains were not accessible. The problem is solved by removing the registry entries i.e TSL1.0, TSL1.1, TSL1.2, SSL3.0 both client and server, It was added before because of poodle vulnerability (mentioned in https://technet.microsoft.com/en-us/library/security/3009008.aspx) . Now when everything looks fine got another problem “Not enough storage is available to process this command” error in RDP login screen after i gave the credentials. When I got in to the server through kvm console of the softlayer, In the event log there were 3 repeated errors of SChannel with the...
This topic first appeared in the Spiceworks Community

Itunes blue screen error

I recently installed itunes from the disk that came with the ipod nano.
The problem I'm having is that when you open itunes with or without the ipod connected it crashed the computer. I rang apple and they said its a windows problem although they did suggest I download version 6 from their web site which I did and the problem still exists. I rang microsoft support and they said it was an apple problem
The problem doesn't happen all the time, around say 80% the computer shots down with a blue screen error message saying " A problem has been detected and windows
has been shut down to prevent damage to your computer.
PageFault_In_NonpagedArea
The technical information is:
STOP 0x00000050 (0xBB9EA29E,0x00000000,0x805-DA81,0x00000002) Then it
goes onto say beginning to dump physical memory, dumping physical memory to disk.
Can anyone help.
Regards

Hello,
I followed this recommendation for one of the other discussions to at least get the blue screens to stop for a while. So far so good. Try this to see if it helps. Make sure you sequence exactly or else blue screens will appear again. Good luck!
BE
Re: USB Device Not Regonized
Posted: Dec 26, 2005 8:11 AM in response to: Chaos Atheist Reply Email
I spent hours last night and today, when something simple actually worked!
If you've uninstalled/reinstalled recently, don't bother. The problem is probably the nano, NOT the computer.
Reset your nano. Move the hold switch until you see orange, then back again, lay it on the table and press the center of the wheel and menu at the same time and hold until you see the apple (6 to 10 seconds).
Then plug your cable into your computer's usb first, then connect the ipod to it. Wait. Hope it works for you

Process contract screen error

Similar Messages

Maybe you are looking for