PX4-300d is blocked in startup with 95% for 2 days already ! HELP !

Hi
My PX4-300d 4 disks 1 Tb , has 1 year and gave an alert about disk01 . Made a restart from EMC control panel ( normally this was solved this way in my old Iomega NAS) and now after power up a bar with 95% is presented on LCD and i cant get acess to nothing . this is already for 48 h , cant be a rebuild of the RAID , itsblocked ...
status led is off -
drive led is blinking sometimes
What shall i do to try to recover my info?
1-power off ?
2-remove and substitute drive that gave error? theorically system should work with only 3 drives ,
3-back button reset ?
Regards
Solved!
Go to Solution.

I'm sorry, I thought you already had a spare drive available. If you bought your device a year ago and registered it, then it should still be in warranty. Or if you have the original purchase receipt, they will be able to update your warranty and replace the hard drive for you per the warranty.
You might have to shut down the device when you replace the hard drive (I would shut the device down anyway to avoid further problems and data loss). Your data should still be there as long as no other drives fail. If you need to do data recovery on the hard drives, you can connect them to a Linux based device that will be able to read from the drives and retrieve the data.
Have questions and need answers?
Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
LenovoEMC Support & Downloads
LenovoEMC North America Support Contact Page

Similar Messages

Displaying Large Blocks of Text with Flex for Mobile

Hi,
I have prepared an application for Android in Adobe Flash Builder. In application there are prayers in Arabic as a list. In app , short prayers are displaying quickly, but long prayers are displaying after a long time. This is my problem.
I share my project file in addition.Can anybody help me, please?
Note: I used SQLite database in my project as you can see and I used a font to view prayers in Arabic.
My Project FB 4.7 Link:
My Project FB 4.6 Link:
Regards,
Burhan

Hi,
I have prepared an application for Android in Adobe Flash Builder. In application there are prayers in Arabic as a list. In app , short prayers are displaying quickly, but long prayers are displaying after a long time. This is my problem.
I share my project file in addition.Can anybody help me, please?
Note: I used SQLite database in my project as you can see and I used a font to view prayers in Arabic.
My Project FB 4.7 Link:
My Project FB 4.6 Link:
Regards,
Burhan

PROBLEMS With my FOR LOOP , PLEASE HELP!!!

Hello,
I have the following event action button method. It has a loop itterates 10 times. I have an imagePanel of a map with an image of a car over the map. The car image moves with the method moveCar();
MY PROBLEM: even though i have my moveCar() method inside the for loop, it doesnt move the car on the map until the loop is finished executing and the car image just jumps over. Can somebody pleae tell me why it does this and how to fix it?????????? thanks so much      public ActionListener startActionListener() {
         ActionListener listener = new ActionListener() {
         public void actionPerformed(ActionEvent event) {
         for (int i=0; i<10; i++) {
                         imagePanel.moveCar();
                    try {
                         Thread.sleep(1000); //waits approx. 1 second
                    } catch (InterruptedException e) {
                         System.exit(0);
           return listener;
     }thanks!

Well, the easiest way is like this:
public ActionListener startActionListener()
     ActionListener listener = new ActionListener()
          public void actionPerformed(ActionEvent event)
               new Thread(new Runnable()
                    public void run()
                         for (int i=0; i<10; i++)
                              imagePanel.moveCar();
                              imagePanel.repaint();
                         try
                              Thread.sleep(1000); //waits approx. 1 second
                         catch (InterruptedException e)
                              //System.exit(0);
               }).start();
          return listener;
}I simply converted your loop to run asynchronously and added a call to repaint after the move. You would be better off to use a Swing Timer instead, but I will leave that to you.

Having trouble with playlist for days!!!! ggrrrrr!

I've tried a lot fo things and no results...even bought PodUtil but still nothing works! when i hook up my ipod to my computer under "devices" I can see my ipod and if i click on it i can see all my songs and PLAYLISTS!! but I cant see the playlist in the actual Itunes! so if i disconnect it the playlist is gone...i want to import music and be able to add them to my playlist but there are not there! is there a ways i can transfer the playlist straight from my ipod to my itunes!??? i've tried export/import but nothing! any help will be good..thank you for your time!

If you create a Playlist inside your iPod, that Playlist will only reside on your iPod - there is no straightforward way of getting that Playlist and its songs back to iTunes.
If you're ever creating a Playlist that you want on your iPod and you might want on your iTunes too, it's best to create it inside the iTunes Library, then drag the Playlist onto your iPod. This way you'll have the Playlist on both your iPod and on iTunes.

Configing Windows pcs with bonjour for network printing help

bonjour downloads and installs correctly
runs setup fine, double click icon
bonjour for windows connects and see the printers
printers install drivers sucessfully
when doing test page thru windows printer configuration
-it then outputs code below example, (not exactly the same)
≈$└24ü≤$5≈$└24ü≤$5≈$└24ü≤$5≈$└24ü≤$5 etc. etc.
computers are windows xp pro sp2 trying to connect and printer.

Are the printers connected to Macs, is so you need to use a postscript driver rather than the actual Windows printer driver.
So if you have a black and white printer, you should use the Apple Laserwriter driver.
If the printer attached is a colour printer use the Apple Color Laserwriter driver regardless of which printer you actually have.
iFelix

Px4-300d port forward iptables 50000- https

Hello. I've searched for similar problems but they weren't exactly the same.
I now need to open a https connection to my px4-300d to share folders to specific users.
I already open a portforward to SSH connection which is working fine.
ssh my.ip -p 50001 gets me to mynas.internal.ip:22
I've created a similar rule on port 50000 to port 443, and it starts to connect. I get the certificate out of date error, but then the connections just hangs there on an empty page.
On wireshark I can't see much more, only that my router/pc starts the TLSv1 session, but right after it sends a [FIN, ACK]
Any ideas please?
Thanks and regards.
Dave
Solved!
Go to Solution.

That is not fully true. Once you know the external ip adress of your network you can access your device both via https and ftp. eg.g. https://<external-ip> or ftp://<user-name>:<user-password>@<external-ip>.
(have not checked if this is true when cloud has never set up)
Bearing this in mind you can configure your router to use an own dyn-service with same portforwarding rules as with the cloud..........
Various PCs / Laptops ( sorry I still really love Dell and Fujitsu ;-))
Supporting Customers ix2s and ix4s -- Love Networking ( not only technically ).
I am not a Lenovo Employee.
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!

My px4-300r stuck at 95% for days

I have px4-300r storage device. it stuck at 95% for days. I tried the possible solutions mentioned in the similar topics (like remove disks and re-seat it , ... ) please help me even if I'll lose my data

Hello Mulham,
I would try booting the NAS with no drives installed.
If it boots, try adding the drives, one-by-one, giving about a miniute between each one, while the NAS is still powered up.
If the NAS will not boot with the drives removed, you will need to start a support ticket with a local agent:
https://lenovo-eu-en.custhelp.com/app/answers/detail/a_id/14722

Help with updates for CS6

I need help installing latest updates for CS6. I have Win 7 and have tried updating from the Help - Updates menu. The error is: U43M1D207.

Thanks for your response. I am in the United States in So. Arizona.
Date: Fri, 5 Oct 2012 12:21:45 -0600
From: [email protected]
To: [email protected]
Subject: Help with updates for CS6
Re: Help with updates for CS6 created by Jeff A Wright in Downloading, Installing, Setting Up - View the full discussion
Crunkle1 you are welcome to work directly with our support team for guided assistance. If you go to http://www.adobe.com/ and select Help and Contact Us you should be given the option to contact our support team via telephone. Which country/region are you in?
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/4752605#4752605
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4752605#4752605
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4752605#4752605. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Downloading, Installing, Setting Up by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

How do i sync my icloud contacts with outlook for Mac 2011

I need to sync my icloud contacts with Outlook for Mac. Help!

You can't, as Microsoft chose not to include the CardDAV protocol necessary to do so (even though they do in Microsoft Office). See http://support.microsoft.com/kb/2648915. To sync your iCloud contacts with your Mac you'll need to use the OS X Contacts (Address Book) app.

PX4-300D blocked 95%

Hi,
Yesterday I switched on the PX4-300D and it was blocked starting up at 95%. I don't have access to the web page and I can't do anything.
I shutted down pressing the power button for a long time and I restarted it but it keeps at 95%
I have sent an email to the support contact but I haven't receive an answer.
What can I do?
Thanks.

Hello danijoint
Usually devices hanging at 95% boot is due to a firmware or disk error.
I recommend that you try the following:
-- power off th unit, re-seat all disks, then try booting again.
-- If you were receiving an error for a specific disk before this began, please remove the disk and try booting without it.
-- try swapping disk 1 with one of the other disks in the unit while powered down. Then try booting again.
-- If the above does not work, you can try disk/bay isolation by trying to boot the unit each disk one at a time, we recommend trying each disk in each bay.
-- If there is still no change, try booting the unit without disks to see if the unit can boot on it's own as it should.
Please contact support if there is not change or if it can't boot on it's own.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

How can I config. ES File Explorer for use with PX4-300D?

I have ES File Explorer on my phone and tablet. I'd like to configure it to work with my PX4-300D but so far everything I've tried does not work. Has anyone else got this to work? If so could you please outline the steps I need to take?
v

Hello rpvincent, try
* firefox.exe -new-window <url>
(the url is without < >)
see also : http://kb.mozillazine.org/Command_line_arguments
thank you

Px4-300d recovery don't work

Hello,
I have a px4-300d with version 4.1.110.33149 and with 4 dd 3TB.
I am raid 5 mode with data 2to top.
I had a crash dd No. 3 and I followed the replacement procedure for the new dd (clean).
I replaced the dd and data recovery process is started. I know this is long but it's been two days since ca shows 0 % and I can not enter to the interface. The white top light flashes every second and the blue LED below blinks once every 30 seconds .
The stop button stops responding over time unless I support and that makes a sudden stop. I raised the same procedure twice and it does the same thing every time. I am in the same situation it has been two days since it is blocked.
Do you have a solution to this problem ?

hello,I have a px4-300d with version 4.1.110.33149 and with 4 dd 3TB.I am raid 5 mode with data 2to top.I had a crash dd No. 3 and I followed the replacement procedure for the new dd (clean).
I replaced the dd and data recovery process is started.I know this is long but it's been two days since ca shows 0 % and I can not enter to the interface.The white LED flashes every second and the blue LED below blinks once every 30 seconds .The stop button stops responding over time unless I support and that makes a sudden stop.I raised the same procedure twice and it does the same thing every time.I am in the same situation it has been two days since it is blocked. Do you have a solution to this problem ?

Unable to enable security and create admin user after reset - px4-300d

Our px4-300d became inaccessible a few days ago. I couldn't get to any shares from any machine, and I couldn't get to the admin console. When I checked the unit, there was no indication that anything was wrong (ie - the panel didn't show any failure, I didn't get any emails indicating a failure, and there were no lights offering a clue to what was wrong). However the unit was completely frozen...the buttons on the front would not scroll through the different information on the panel.
I attempted to reset the device using the pinhole on the back, but the device wouldn't respond, so I had to power it down using the button on the front. When I tried to power it back up, it would come on for about one second, then immediately power off. I pulled all 4 drives out and powered it on again without any drives. This time it came up completely and I got a message on the panel that drives were missing. I started putting the drives in one at a time and the device recognized them all and I was able to login to the admin console. However, all the shares were missing and I received an email that the Storage Pool was degraded. I rebooted the device from the admin console and when it came back up, it started reconstruction. After a few hours, it completed, but I still had no shares and couldn't create any new shares. I also did not see any of my users, including the admin account I was logged in with. I tried to create a new user, and also tried creating a user I knew existed and neither one worked. The screen would just flash but nothing would show up. At this point, I decided to try to reset using the pinhole on the back of the device to reset the admin user so I could just create a new one. So, now I'm stuck at the 'Enable Security' screen. Every time I try to create an admin account, it just flashes and returns me to the same 'Enable Security' window.
Now what?
Solved!
Go to Solution.

If you are unable to get into it you will not be able to do the factory reset. You can try booting in buy removing one disk at a time. If you are still unable to then tech support should be able to supply you with the imager and try flashing it. I would keep it at 4.0.8 also,

BLACK SCREEN startup with 3 beeps, FREEZES when unplugged, Splash screen freeze, HEAT-UP TO BOOT

BLACK SCREEN startup with 3 beeps, FREEZES when power unplugged, IF IT BOOTS splash screen freezes, OVERHEATING REQUIRED TO BOOT - 0x7B, Event 41 kernel-powe
Issue: One day I unplug the power, the screen freezes and I get frozen music sound. I shut down, start up, I get 3 beeps (1 short 2 long), which indicates a Video failure according to the Thinkpad Laptop beep code list.
How I solve the issue day-to-day: I turn the heat up - I disconnect the battery and hard drive and plug in the power then turn it on. I will wait until the underneath is searing hot with a blanket blocking the fan's flow of air, I mean way hot because any cooler and it won't start. Plug stuff back in, Hard drive first, Battery second, turn off with power button hold, unplug power, replug power.
I turn it on, no beeps, it goes past the first Lenovo screen, then gives me a prompt because it "didn't shut down properly" and continue regular startup. What happens next is the Windows logo appears, and just as the animated windows logo starts to move (you see 2 small colored dots on the screen), it freezes. I see this every time, I know naturally that it means that the laptop is still too hot to go past that point, so I shut it down and try again. After about 5 - 10 tries it will go past the splash screen and into the login area, then it's all fine.
Sometimes when I unplug the power from the back by accident it will freeze. By accident I mean that the connector wiggles it's self out easily. This unplug freezing thing started happening about 1 week before the 3 beep black screen problem started rolling, so I'm putting 2 together.
Errors:
I got a Blue Screen of Death the first time I started it up with the overheating ritual, but I never got it since. It was 0X7B. I ended up changing a setting in BIOS from AHCI to Compatibility Mode, and I passed everything without the BSOD again. I have always had it on AHCI.
I got another Blue Screen of Death about a week ago, but came as it was on already and I had been using it, and said something about disabling Cache or Shadowing in BIOS. I never got it since.
BIOS:
Also, the time was set to 1988 or something in the BIOS.
Event Viewer events found:
1. Kernel-Power, Summary page.
There are critical events for a few things like Kernel-Power, Event ID 41, Task Category (63). There are 19 of them, each day 1 or 2 of them but mostly 1, so this maybe corresponds to my daily ritual.
"The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly."
2. Kernel-Processor-Power - Event ID 37, task category (7)
"The speed of processor 1 in group 0 is being limited by system firmware. The processor has been in this reduced performance state for 71 seconds since the last report."
3. LMS - HCMI - Event ID 2, Task Category: none
"LMS Service cannot connect to HECI driver".
I came across a very sluggish performing control panel for Nvidia before and after this problem, and I tried installing a newer version, which I had to jump through a few hoops to do, like uninstalling first, not just updating. At first it said that the driver wasnt made for the system, or that it wasnt compatible or something, which was wrong. I made it work somehow, but it was still sluggish after install. I rolled it back to an earlier driver, and now it works fine oddly. No sluggish performance / slight freeze window thing going on. No problem at all.
MSCONFIG.exe, Boot Advanced Options: I have tried twice to change this 1 setting, check box "Number of processors" and change to 2 processors, because I do have 2 processors. I have been able to change this in the past, but it does not save the setting now, and I believe this option was selected before I started having problems, and settings did not disappear then.
What could this be. The small round BIOS battery? The video card like everyone presumes? (I.E. the entire motherboard replacement), Software? The wiggly power input area? (Not enough power getting in?), Firmware of some sort? The BIOS software being wrong?
SYSTEM INFO:
Thinkpad T61p 6457-A24, Intel core 2 duo (T7700) 2.4GHz, Intel 120GB SSD 6Gb/s, NVIDIA Quadro FX 570M (256 MB),
Windows 7 64 bit Home Premium (6.1, Build 7601), BIOS Ver 1.00PARTTBLx
Display: 1680 x 1050 (32 bit 60 Hz), Integrated RAMDAC, Main driver: nvd3dumx.dll,nvwgf2umx,nvwgf2,
Version 8.17.12.9688, Date 5/31/2012, DDI version 10, Driver model WDDM 1.1

T61-Elwood wrote:
Laptops of all Brands using Nvidia GPUsmade from 2007-2008 are faulty.
You wont get good Nvidia ones on Ebay/forumes anywhere.
I'd beg to differ on both accounts.
*61 series nVidia-based ThinkPads from late January through July of 2008 are a 50/50 shot, since the old chips were mixed with the new ones. Any machine built in August and later can be deemed "safe".
As for the forums (I don't do feebay) there are people who sell genuine, properly-tested planars. However, these do not come at bargain basement prices, and with a good reason if I may add.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Disk Utility says everything's fine, but Install disk doesn't find my internal drive as a possible destination. When I startup with Command S, I get a looping "cannot mount errno = 19" message.

Disk Utility says everything's fine, but Install disk doesn't find my internal drive as a possible destination. When I startup with Command + S, I get a looping "cannot mount errno = 19" message.
Problem started when I used Tech Tool Pro 6 to "de-fragment volume". Had to cancel that process before it finished because I ran out of time. Thereafter, when I startup my machine normally, I get the gray Apple logo at first, but it changes to a prohibited symbol (circle with a slash thru it) and hangs.
When I startup holding the Option key, I can see my internal drive, but I get the same results as above.
When I startup using the MacBook OSX Install DVD, it does not find my internal drive as possible destination.
When I startup using the MacBook OSX Install DVD and then run Disk Utility, it finds my drive, allows me to "repair" and says everything is fine.
When I startup with Command + S, I get a looping error message "errno = 19" and cannot stop it to do anything else.
When I startup from Disk Warrior v4.4, it does not find my internal drive to do any repairs.
When I startup from Tech Tool Pro 6 and run the "computer check" diagnostics, everything passes but the Volume Structure, which fails at "Volume Extents (B-tree)." When I use TTP's "Tools" option to run "volume repair" it will show my internal drive and allow me to click the GO button, but nothing happens and nothing changes.
I have a Time Machine backup on an external USB drive, but for as long as the internal drive doesn't mount, I can't use the backup to restore.

It's a false report and should be ignored.
I would not rely on TT as I've already said earlier even before Grant posted similar advice.
I really think the Rigid Disk Block may be corrupted. This holds the partition map and could prevent a volume from being unmounted. Unfortunately, there is no way to fix that without repartitioning the drive which will remove everything. So, before going down this road I hope you have backups or can make a backup.
Drive Partition and Format
1. Boot from your Snow Leopard Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. Quit DU and return to the installer. Proceed with reinstalling OS X.
5. Download and install Mac OS X 10.6.8 Update Combo v1.1.

PX4-300d is blocked in startup with 95% for 2 days already ! HELP !

Similar Messages

Maybe you are looking for