Quickvpn / client to gateway vpn rv042 can only ping router
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.
I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
Any ideas?
I've narrowed the problem down to option 2 above. If I change the gateway of a LAN resource to point to the LAN side of the router, it can be accessed through the VPN tunnel.
I haven't had time to see if adding routing entries can fix this problem. Any suggestions will be appreciated.
Also, I would appreciate an explanation of why the PPTP connection works. I will research this myself (eventually) but am already backed up with other projects..
Similar Messages
-
VPN client connected to VPN but can't ping or access to server
HI ,
i need help urgently, had been troubleshooting for a day, but have no ideal what wrong with the config.
Basically there is 2 set of VPN configured, one is site to site IPSEC VPN and another one is connect via VPN client software coexist in same router.
This recently we having problem on client can't access or ping to internal server which is 192.168.6.3 from VPN client software.
VPN client will connect to VPN ip pool as10.20.1.0 to 10.20.1.100
Software itself shown connected but request time out when ping.
Below is the config. Some of the command might be extra as when i did some test, but end up didn't work.
aaa new-model
aaa authentication login userauthen local
aaa authorization network adminmap group VPNClient
aaa authorization network groupauthor local
aaa authorization network map-singapore local
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
crypto isakmp key emptyspace address 203.142.83.218 no-xauth
crypto isakmp keepalive 15 periodic
crypto isakmp client configuration address-pool local ippool
crypto isakmp client configuration group map-singapore
key cisco123
dns 192.168.6.3
domain cisco.com
pool ippool
acl 102
crypto isakmp profile VPNclient
match identity address 27.54.43.210 255.255.255.255
match identity group vpnclient
client authentication list userauthen
client configuration address respond
crypto ipsec security-association idle-time 86400
crypto ipsec transform-set REMSET esp-3des esp-md5-hmac
crypto ipsec transform-set DYNSET esp-aes esp-md5-hmac
crypto ipsec transform-set esp-3des-sha esp-3des esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set DYNSET
set isakmp-profile VPNclient
reverse-route
crypto map VPNMAP client authentication list userauthen
crypto map VPNMAP isakmp authorization list map-singapore
crypto map VPNMAP client configuration address respond
crypto map VPNMAP 10 ipsec-isakmp dynamic dynmap
crypto map VPNMAP 11 ipsec-isakmp
description VPN to ASA5520
set peer 203.142.83.218
set security-association lifetime kilobytes 14608000
set security-association lifetime seconds 86400
set transform-set REMSET
match address 100
interface GigabitEthernet0/0
ip address 27.54.43.210 255.255.255.240
ip nat outside
no ip virtual-reassembly
duplex full
speed 100
crypto map VPNMAP
interface GigabitEthernet0/1
ip address 192.168.6.1 255.255.255.0
ip nat inside
no ip virtual-reassembly
duplex full
speed 100
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
ip local pool ippool 10.20.1.0 10.20.1.100
ip forward-protocol nd
ip pim bidir-enable
no ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0 overload
ip nat inside source list 101 interface GigabitEthernet0/0 overload
ip nat inside source route-map nonat interface GigabitEthernet0/0 overload
ip nat inside source static 192.168.6.3 27.54.43.212
ip route 0.0.0.0 0.0.0.0 27.54.43.209
ip route 192.168.1.0 255.255.255.0 27.54.43.209
ip route 192.168.151.0 255.255.255.0 192.168.6.151
ip route 192.168.208.0 255.255.255.0 27.54.43.209
ip access-list extended RA_SING
permit ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.0.0.0 0.255.255.255 192.168.6.0 0.0.0.255
permit ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
permit ip 10.20.1.1 0.0.0.100 192.168.6.0 0.0.0.255
permit ip 10.20.1.0 0.0.0.255 10.0.0.0 0.255.255.255
deny ip any any log
access-list 1 remark Local Network
access-list 1 permit 192.168.6.0 0.0.0.255
access-list 1 permit 192.168.102.0 0.0.0.255
access-list 1 permit 192.168.151.0 0.0.0.255
access-list 2 remark VPNClient-range
access-list 2 permit 10.0.0.0 0.255.255.255
access-list 10 permit 192.168.6.0 0.0.0.255
access-list 10 permit 192.168.102.0 0.0.0.255
access-list 10 permit 192.168.151.0 0.0.0.255
access-list 10 permit 10.0.0.0 0.255.255.255
access-list 100 permit ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 100 permit ip 192.168.102.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 100 permit ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
access-list 100 permit ip host 192.168.6.7 host 192.168.208.48
access-list 101 deny ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 101 permit ip 10.0.0.0 0.255.255.255 any
access-list 101 permit ip 192.168.6.0 0.0.0.255 any
access-list 102 permit ip 10.0.0.0 0.255.255.255 any
access-list 120 deny ip any any log
access-list 120 deny ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255 log
access-list 120 deny ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 120 deny ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
no cdp run
route-map nonat permit 10
match ip address 120
control-plane
alias isakmp-profile sh crypto isakmp sa
alias exec ipsec sh crypto ipsec sa
banner motd ^CC^CI did not try to ping 4.2.2.2. I just know I can not ping comcasts dns servers. I have updated the firmware on the router and it did not work. The computer was able to access the internet until about a week ago, I don't understand what could have changed that I would now need a static DNS.
-
RV320 Client-to-Gateway VPN IP address
Is there anyway to have the VPN client be a member of the LAN IP address space - VPN bridge mode? Would like for the client machine to be in the same address space so it can discover printers, scanners, broadcast packets, Bounjour discovery, NETBIOS broadcasts, etc.
The RV320 seems to enforce: "Start IP can not be in LAN or Multi-Subnet IP range"
VPN client-to-gateway works well using VPN Tracker 8 from e-quinux.
73/gus
Dr. Gus LottHello Kevin,
Thanks for responding!
We have one headquarter - unfortunately I called it location B - and a new branch Location A with a newly purchased RV0082, new computer, it needs to be connected to the headquarter's server to have access to inventory software located on the server.
The document you shared was well used already for the recent days and was great help.
The setup from headquarter was not mine, I found out today that apparently there is a router between splitter and the RV082 - a Comcast business router, and its address is the one RV082 pulls.
I have no idea how I can work around the Comcast router, I can't attach the RV082 directly to the splitter and I can't simply unplug the Comcast router because of other services it provides.
I reset the Comcast router to gain access with default login, but it failed - seems to be a usual problem as far as I could find out via internet.
Is there any way that I can create a VPN tunnel with the comcast router in between?
The headquarter is an actively running store, the new location opens Saturday (I'm a kind of in a hurry)
I very much hope you have a hint for me.
Thanks,
PS: I just learned that the splitter is only for telephone. So it's a parallel structure: incoming cable splits in TV, Telephone and the Comcast router. It looks like I have to live with the Comcast router in between.
Thanks so much for any help -
Cisco ASA 5510 - Cisco Client Can Connect To VPN But Can't Ping!
Hi,
I have an ASA 5510 with the configuration below. I have configure the ASA as remote access vpn server with cisco vpn client, my problem now is I can connect but I can't ping.
Config
ciscoasa# sh run
: Saved
ASA Version 8.0(3)
hostname ciscoasa
enable password 5QB4svsHoIHxXpF/ encrypted
names
name xxx.xxx.xxx.xxx SAP_router_IP_on_SAP
name xxx.xxx.xxx.xxx ISA_Server_second_external_IP
name xxx.xxx.xxx.xxx Mail_Server
name xxx.xxx.xxx.xxx IncomingIP
name xxx.xxx.xxx.xxx SAP
name xxx.xxx.xxx.xxx WebServer
name xxx.xxx.xxx.xxx cms_eservices_projects_sharepointold
name 192.168.2.2 isa_server_outside
interface Ethernet0/0
nameif outside
security-level 0
ip address IncomingIP 255.255.255.248
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.253 255.255.255.0
management-only
passwd 123
ftp mode passive
clock timezone EEST 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
object-group service TCP_8081 tcp
port-object eq 8081
object-group service DM_INLINE_TCP_1 tcp
port-object eq 3389
port-object eq ftp
port-object eq www
port-object eq https
port-object eq smtp
port-object eq pop3
port-object eq 3200
port-object eq 3300
port-object eq 3600
port-object eq 3299
port-object eq 3390
port-object eq 50000
port-object eq 3396
port-object eq 3397
port-object eq 3398
port-object eq imap4
port-object eq 587
port-object eq 993
port-object eq 8000
port-object eq 8443
port-object eq telnet
port-object eq 3901
group-object TCP_8081
port-object eq 1433
port-object eq 3391
port-object eq 3399
port-object eq 8080
port-object eq 3128
port-object eq 3900
port-object eq 3902
port-object eq 7777
port-object eq 3392
port-object eq 3393
port-object eq 3394
port-object eq 3395
port-object eq 92
port-object eq 91
port-object eq 3206
port-object eq 8001
port-object eq 8181
port-object eq 7778
port-object eq 8180
port-object eq 22222
port-object eq 11001
port-object eq 11002
port-object eq 1555
port-object eq 2223
port-object eq 2224
object-group service RDP tcp
port-object eq 3389
object-group service 3901 tcp
description 3901
port-object eq 3901
object-group service 50000 tcp
description 50000
port-object eq 50000
object-group service Enable_Transparent_Tunneling_UDP udp
port-object eq 4500
access-list inside_access_in remark connection to SAP
access-list inside_access_in extended permit ip 192.168.2.0 255.255.255.0 host SAP_router_IP_on_SAP
access-list inside_access_in remark VPN Outgoing - PPTP
access-list inside_access_in extended permit tcp 192.168.2.0 255.255.255.0 any eq pptp
access-list inside_access_in remark VPN Outgoing - GRE
access-list inside_access_in extended permit gre 192.168.2.0 255.255.255.0 any
access-list inside_access_in remark VPN - GRE
access-list inside_access_in extended permit gre any any
access-list inside_access_in remark VPN Outgoing - IKE Client
access-list inside_access_in extended permit udp 192.168.2.0 255.255.255.0 any eq isakmp
access-list inside_access_in remark VPN Outgoing - IPSecNAT - T
access-list inside_access_in extended permit udp 192.168.2.0 255.255.255.0 any eq 4500
access-list inside_access_in remark DNS Outgoing
access-list inside_access_in extended permit udp any any eq domain
access-list inside_access_in remark DNS Outgoing
access-list inside_access_in extended permit tcp any any eq domain
access-list inside_access_in remark Outoing Ports
access-list inside_access_in extended permit tcp 192.168.2.0 255.255.255.0 any object-group DM_INLINE_TCP_1
access-list inside_access_in extended permit ip 172.16.1.0 255.255.255.0 any
access-list outside_access_in extended permit ip any any
access-list outside_access_in extended permit tcp any any eq pptp
access-list outside_access_in extended permit gre any any
access-list outside_access_in extended permit gre any host Mail_Server
access-list outside_access_in extended permit tcp any host Mail_Server eq pptp
access-list outside_access_in extended permit esp any any
access-list outside_access_in extended permit ah any any
access-list outside_access_in extended permit udp any any eq isakmp
access-list outside_access_in extended permit udp any any object-group Enable_Transparent_Tunneling_UDP
access-list VPN standard permit 192.168.2.0 255.255.255.0
access-list corp_vpn extended permit ip 192.168.2.0 255.255.255.0 172.16.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool POOL 172.16.1.10-172.16.1.20 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-603.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 2 Mail_Server netmask 255.0.0.0
global (outside) 1 interface
global (inside) 2 interface
nat (inside) 0 access-list corp_vpn
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp Mail_Server 8001 ISA_Server_second_external_IP 8001 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 8000 ISA_Server_second_external_IP 8000 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server pptp isa_server_outside pptp netmask 255.255.255.255
static (inside,outside) tcp Mail_Server smtp isa_server_outside smtp netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 587 isa_server_outside 587 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 9444 isa_server_outside 9444 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 9443 isa_server_outside 9443 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 3389 isa_server_outside 3389 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 3390 isa_server_outside 3390 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 3901 isa_server_outside 3901 netmask 255.255.255.255
static (inside,outside) tcp SAP 50000 isa_server_outside 50000 netmask 255.255.255.255
static (inside,outside) tcp SAP 3200 isa_server_outside 3200 netmask 255.255.255.255
static (inside,outside) tcp SAP 3299 isa_server_outside 3299 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server www isa_server_outside www netmask 255.255.255.255
static (inside,outside) tcp Mail_Server https isa_server_outside https netmask 255.255.255.255
static (inside,outside) tcp Mail_Server pop3 isa_server_outside pop3 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server imap4 isa_server_outside imap4 netmask 255.255.255.255
static (inside,outside) tcp cms_eservices_projects_sharepointold 9999 isa_server_outside 9999 netmask 255.255.255.255
static (inside,outside) 192.168.2.0 access-list corp_vpn
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set transet esp-des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map dynmap 10 set pfs
crypto dynamic-map dynmap 10 set transform-set transet ESP-3DES-SHA
crypto map cryptomap 10 ipsec-isakmp dynamic dynmap
crypto map cryptomap interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
no crypto isakmp nat-traversal
telnet 192.168.2.0 255.255.255.0 inside
telnet 192.168.1.0 255.255.255.0 management
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd dns xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx interface inside
dhcpd domain domain.local interface inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics access-list
tftp-server management 192.168.1.123 /
group-policy mypolicy internal
group-policy mypolicy attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN
username vpdn password 123
username vpdn attributes
vpn-group-policy mypolicy
service-type remote-access
tunnel-group mypolicy type remote-access
tunnel-group mypolicy general-attributes
address-pool POOL
default-group-policy mypolicy
tunnel-group mypolicy ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect pptp
service-policy global_policy global
prompt hostname context
Cryptochecksum:b8bb19b6cb05cfa9ee125ad7bc5444ac
: end
Thank you very much.Here is the output:
ciscoasa# packet-tracer input outside icmp 172.16.1.10 8 0 192.168.2.1
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 2
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
static (inside,outside) 192.168.2.0 access-list corp_vpn
nat-control
match ip inside 192.168.2.0 255.255.255.0 outside 172.16.1.0 255.255.255.0
static translation to 192.168.2.0
translate_hits = 0, untranslate_hits = 139
Additional Information:
NAT divert to egress interface inside
Untranslate 192.168.2.0/0 to 192.168.2.0/0 using netmask 255.255.255.0
Phase: 3
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group outside_access_in in interface outside
access-list outside_access_in extended permit ip any any
Additional Information:
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: CP-PUNT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect icmp
service-policy global_policy global
Additional Information:
Phase: 7
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
static (inside,outside) 192.168.2.0 access-list corp_vpn
nat-control
match ip inside 192.168.2.0 255.255.255.0 outside 172.16.1.0 255.255.255.0
static translation to 192.168.2.0
translate_hits = 0, untranslate_hits = 140
Additional Information:
Phase: 11
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule -
ASA 5505 VPN clients can't ping router or other clients on network
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
ASA Version 7.2(4)
hostname ASA
domain-name default.domain.invalid
enable password kdnFT44SJ1UFX5Us encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.4 Server
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list vpn_splitTunnelAcl standard permit any
access-list inside_nat0_outbound extended permit ip any 10.0.0.192 255.255.255.192
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPNpool 10.0.0.220-10.0.0.240 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface smtp Server smtp netmask 255.255.255.255
static (inside,outside) tcp interface pop3 Server pop3 netmask 255.255.255.255
static (inside,outside) tcp interface www Server www netmask 255.255.255.255
static (inside,outside) tcp interface https Server https netmask 255.255.255.255
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable 480
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs group1
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
group-policy vpn internal
group-policy vpn attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn_splitTunnelAcl
username admin password wwYXKJulWcFrrhXN encrypted privilege 15
username VPNuser password fRPIQoKPyxym36g7 encrypted privilege 15
username VPNuser attributes
vpn-group-policy vpn
tunnel-group vpn type ipsec-ra
tunnel-group vpn general-attributes
address-pool VPNpool
default-group-policy vpn
tunnel-group vpn ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:df7d1e4f34ee0e155cebe86465f367f5
: end
Any ideas what I need to add to get the vpn client to be able to ping the router and clients?
Thanks.I tried that and it didn't work. As for upgrading the ASA version, I'd like to but this is an old router and I don't have a support contract with Cisco anymore, so I can't access the latest firmware.
here is the runnign config again:
Result of the command: "show startup-config"
: Saved
: Written by enable_15 at 01:48:37.789 MDT Wed Jun 20 2012
ASA Version 7.2(4)
hostname ASA
domain-name default.domain.invalid
enable password kdnFT44SJ1UFX5Us encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.0.0.4 Server
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list vpn_splitTunnelAcl standard permit any
access-list inside_nat0_outbound extended permit ip any 10.0.0.192 255.255.255.192
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPNpool 10.0.0.220-10.0.0.240 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
asdm location Server 255.255.255.255 inside
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface smtp Server smtp netmask 255.255.255.255
static (inside,outside) tcp interface pop3 Server pop3 netmask 255.255.255.255
static (inside,outside) tcp interface www Server www netmask 255.255.255.255
static (inside,outside) tcp interface https Server https netmask 255.255.255.255
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable 480
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs group1
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
group-policy vpn internal
group-policy vpn attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn_splitTunnelAcl
username admin password wwYXKJulWcFrrhXN encrypted privilege 15
username VPNuser password fRPIQoKPyxym36g7 encrypted privilege 15
username VPNuser attributes
vpn-group-policy vpn
tunnel-group vpn type ipsec-ra
tunnel-group vpn general-attributes
address-pool VPNpool
default-group-policy vpn
tunnel-group vpn ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
service-policy global_policy global
prompt hostname context
Cryptochecksum:78864f4099f215f4ebdd710051bdb493 -
I can connect my cisco mobile vpn but can't ping & access internal IP
Hi somebody,
i've configured mobile vpn configuration in cisco 7200 with GNS3. i can connect VPN to my cisco router with cisco vpn client software from outside. but i can't ping to internal ip and can't access internal resources.
My Internal IP is 192.168.1.x . And IP for mobile VPN client from outside is 172.60.1.x.
Your advise will be appreciate.
here is my configuration with cisco 7200 in GNS 3,
OfficeVPN_Router#sh run
Building configuration...
Current configuration : 2186 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname OfficeVPN_Router
boot-start-marker
boot-end-marker
enable secret 5 $1$E0Gz$U8UzNtHOXy2CeoEFj30by0
aaa new-model
aaa authentication login userlist local
aaa authorization network grouplist local
aaa session-id common
ip cef
no ip domain lookup
username asm privilege 15 password 0 pncsadmin
username user privilege 15 password 0 pncsadmin
username user1 privilege 15 password 0 pncsadmin
username cisco123 secret 5 $1$lCOc$Db.e8AFd/0f02ZI4/aeV./
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp client configuration group MWG
key cisco
dns 165.21.83.88
pool vpnpool
acl 101
netmask 255.255.0.0
crypto ipsec transform-set myset esp-aes esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map mymap client authentication list userlist
crypto map mymap isakmp authorization list grouplist
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap 10 ipsec-isakmp dynamic dynmap
interface FastEthernet0/0
no ip address
shutdown
duplex half
interface FastEthernet1/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex full
speed 100
interface FastEthernet1/1
ip address 200.200.200.200 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map mymap
ip local pool vpnpool 172.60.1.10 172.60.1.100
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 200.200.200.201
no ip http server
no ip http secure-server
ip nat inside source list 111 interface FastEthernet1/1 overload
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 deny ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 permit ip any any
control-plane
gatekeeper
shutdown
line con 0
exec-timeout 0 0
password cisco123
logging synchronous
stopbits 1
line aux 0
stopbits 1
line vty 0 4
password cisco123
end
OfficeVPN_Router#sh ver
Cisco IOS Software, 7200 Software (C7200-A3JK9S-M), Version 12.4(25), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 21-Apr-09 18:50 by prod_rel_team
ROM: ROMMON Emulation Microcode
BOOTLDR: 7200 Software (C7200-A3JK9S-M), Version 12.4(25), RELEASE SOFTWARE (fc2)
OfficeVPN_Router uptime is 30 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 7206VXR (NPE400) processor (revision A) with 245760K/16384K bytes of memory.
Processor board ID 4279256517
R7000 CPU at 150MHz, Implementation 39, Rev 2.1, 256KB L2 Cache
6 slot VXR midplane, Version 2.1
Last reset from power-on
PCI bus mb0_mb1 (Slots 0, 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb0_mb1 has a total of 600 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4, 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
3 FastEthernet interfaces
125K bytes of NVRAM.
65536K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
OfficeVPN_Router#Dear Javier ,
Thanks for your info. i already tested as you say. but still i can't use & ping to my internal IP which is behind cisco VPN router. i posted my config file.
OfficeVPN_Router(config)#ip access-list resequence 111 10 10
OfficeVPN_Router(config)#do sh run
Building configuration...
Current configuration : 2201 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname OfficeVPN_Router
boot-start-marker
boot-end-marker
enable secret 5 $1$E0Gz$U8UzNtHOXy2CeoEFj30by0
aaa new-model
aaa authentication login userlist local
aaa authorization network grouplist local
aaa session-id common
ip cef
no ip domain lookup
username asm privilege 15 password 0 pncsadmin
username user privilege 15 password 0 pncsadmin
username user1 privilege 15 password 0 pncsadmin
username cisco123 secret 5 $1$lCOc$Db.e8AFd/0f02ZI4/aeV./
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp client configuration group MWG
key cisco
dns 165.21.83.88
pool vpnpool
acl 101
netmask 255.255.0.0
crypto ipsec transform-set myset esp-aes esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map mymap client authentication list userlist
crypto map mymap isakmp authorization list grouplist
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap 10 ipsec-isakmp dynamic dynmap
interface FastEthernet0/0
no ip address
shutdown
duplex half
interface FastEthernet1/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex full
speed 100
interface FastEthernet1/1
ip address 200.200.200.200 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map mymap
ip local pool vpnpool 172.60.1.10 172.60.1.100
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 200.200.200.201
no ip http server
no ip http secure-server
ip nat inside source list 111 interface FastEthernet1/1 overload
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 deny ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
control-plane
gatekeeper
shutdown
line con 0
exec-timeout 0 0
password cisco123
logging synchronous
stopbits 1
line aux 0
stopbits 1
line vty 0 4
password cisco123
end -
Can only ping, nothing else
Hi,
I am in contact with BT regarding this problem, but since there seems to be no progress there I thought I'd try this. I had my BT infinity installed last Wednesday (after an amazing wait of 2 months). Anyway, the engineer installed everything, all lights on the modem are green, all lights on the hub are blue, but I have no internet connection. I can ping machines on the internet (such as 8.8.4.4), but that's it. DNS doesn't work, nor anything else; only ping. BT sent 3 engineers so far; they all say the line is fine, and they don't know what to do. I also ran out of ideas of what else to try; naturally I have checked firewalls etc. on my end, tried multiple devices, wireless/wired, different cables, etc. The engineers also tried different equipement, replaced modem, hub, nothing changed. To me it seems like BT is blocking me somewhere, but all the helpdesk people say all seems fine from their end and they do not know what could be wrong. Did anyone else ever experience anything like this?I get what seems like a reasonable trace route:
> tracert 8.8.8.8
Tracing route to 8.8.8.8 over a maximum of 30 hops
1 1 ms <1 ms <1 ms api.home [192.168.1.254]
2 21 ms 20 ms 20 ms 217.32.141.144
3 21 ms 21 ms 21 ms 217.32.141.222
4 25 ms 25 ms 24 ms 213.120.161.58
5 23 ms 23 ms 23 ms 31.55.164.227
6 23 ms 23 ms 24 ms 31.55.164.109
7 24 ms 24 ms 24 ms 109.159.248.232
8 35 ms 35 ms 35 ms 109.159.248.156
9 32 ms 35 ms 35 ms 62.172.103.189
10 114 ms 28 ms 28 ms 194.72.9.2
11 27 ms 28 ms 28 ms 166.49.168.1
12 28 ms 27 ms 28 ms 166.49.237.25
13 28 ms 28 ms 28 ms 166.49.164.138
14 63 ms 40 ms 30 ms 166.49.135.48
15 34 ms 29 ms 41 ms 166.49.214.134
16 28 ms 28 ms 29 ms 209.85.240.61
17 29 ms 29 ms 29 ms 209.85.253.90
18 35 ms 35 ms 35 ms 209.85.240.28
19 72 ms 37 ms 37 ms 216.239.49.36
20 * 40 ms 39 ms 209.85.255.118
21 38 ms 38 ms 38 ms 8.8.8.8
Trace complete. -
WinXp Pro as Virtualbox Guest can't ping router/internet
Hi:
I am running Arch 64 and installed virtualbox_bin 2.0.4-1 from AUR and guest additions 2.0.2-1 from AUR.
I have installed as a guest os, WinXP Pro and set up bridge networking per
http://mychael.gotdns.com/blog/2007/05/ … -bridging/.
My Arch host works fine (it can access the internet and ping the guest WinXP Pro). My WinXP Pro guest can ping my Arch host and other local machines on my network. However it cannot ping my router or access or ping the internet.
I log onto the WinXP Pro as the Administrator and I have the firewall disabled, so I don't think it is being blocked on the XP side by anything.
As far as Arch goes, I have tried adding the host name of the WinXP Pro machine to /etc/hosts and put the ip adress of the XP machine into /etc/hosts.allow. Neither of these actions resulted in success. I don't think I have a firewall or other special security measures on my Arch? I just did a fresh ftp install yesterday and did not add ssh or other security measures that weren't included in the default install and the base-devel install.
My search of the forums turned up a similar problem to mine that was solved by removing the firewall in the WinXP guest. I have already done that still without success.
My uneducated guess is that the gateway ip is not getting to the guest. I am using static ip for both the Arch host and the WinXP guest. The WinXP guest says that it is connected and reports no problems. I tried using dhcp on the XP guest but that didn't work either.
Here is the network section of my /etc/rc.conf
lo="lo 127.0.0.1"
BRIDGE_INTERFACES=(br0)
bridge_br0=(eth0)
br0="br0 192.168.1.201 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="eth0 0.0.0.0 promisc"
INTERFACES=(lo br0 eth0)
gateway="default gw 192.168.1.1"
ROUTES=(gateway)
Any help would be much appreciated.
bdikaHi Floris:
Thanks for the reply.
I originally tried the Arch Way without success, that is why I tried the other way.
However at your suggestion, I have tried the Arch Way again, with the same results. That is I can ping other computers on my network but I can't ping my router nor access the internet from my guest.
Seeing that I have the same problem regardless of which method I use leads me to believe that it must be something simple and obvious that I am doing wrong. But what??! I have no idea.
Any thoughts you have would be much appreciated.
bdika -
NW Client 3.4 - unattend.txt -- can only be created/edited on W98 for W98
FYI:
After spinning my wheels, trying to figure out why the ACU.EXE and
SETUP.EXE /ACU options wouldn't install with an UNATTEND.TXT, I dis-
covered the problem had to do with having created the file on a Win2K
system.
Unpacking the Novell Client 3.4 on my Windows 2000 professional
I mistakenly thought I could run the NCIMAN.EXE, for version 3.4,
create the UNATTEND.TXT file, and then use this with my install.
Unfortunately, NCIMAN.EXE senses what system you're on and saves the
UNATTEND.TXT file under whatever format is consistant with the O/S
you're working on. [There doesn't seem to be any way to tell NCIMAN
to save the configuration file for a different O/S.]
If, like myself, you miss this . . . the UNATTEND.TXT file will be created
(or saved after editing) under a Windows 2000 format--which won't run
on a Client 3.4 install. [You can verify the version it was saved under
by looking at the second line of the UNATTEND.TXT file . . . the one
that reads: "Novell_Client=" ("95" for Win95/98) or "NT" (for 2000 or
XP).]
'Hope this saves some others from similar grief . . .
Steve Conrad[email protected] wrote:
> FYI:
>
> After spinning my wheels, trying to figure out why the ACU.EXE and
> SETUP.EXE /ACU options wouldn't install with an UNATTEND.TXT, I dis-
> covered the problem had to do with having created the file on a Win2K
> system.
>
> Unpacking the Novell Client 3.4 on my Windows 2000 professional
> I mistakenly thought I could run the NCIMAN.EXE, for version 3.4,
> create the UNATTEND.TXT file, and then use this with my install.
> Unfortunately, NCIMAN.EXE senses what system you're on and saves the
> UNATTEND.TXT file under whatever format is consistant with the O/S
> you're working on. [There doesn't seem to be any way to tell NCIMAN
> to save the configuration file for a different O/S.]
>
> If, like myself, you miss this . . . the UNATTEND.TXT file will be created
> (or saved after editing) under a Windows 2000 format--which won't run
> on a Client 3.4 install. [You can verify the version it was saved under
> by looking at the second line of the UNATTEND.TXT file . . . the one
> that reads: "Novell_Client=" ("95" for Win95/98) or "NT" (for 2000 or
> XP).]
>
> 'Hope this saves some others from similar grief . . .
>
> Steve Conrad
>
>
>
You can also run NCIMAN, Go to File -> New File, and choose the O/S of
choice. :-) -
Connect to VPN but can't ping past inside interface
Hello,
I've been working on this issue for a few days with no success. We're setting up a new Cisco ASA 5515 in our environment and are trying to get a simple IPSec VPN setup on it for remote access. After some initial problems, we've gotten it to where the VPN tunnel authenticates the user and connects as it should, however we cannot ping into our LAN. We are able to ping as far as the firewall's inside interface. I've tried other types of traffic too and nothing gets through. I've checked the routes listed on the VPN client while we're connected and they look correct - the client also shows both sent and received bytes when we connect using TCP port 10000, but no Received bytes when we connect using UDP 4500. We are trying to do split tunneling, and that seems to be setup correctly because I can still surf while the VPN is connected.
Below is our running config. Please excuse any messyness in the config as there are a couple of us working on it and we've been trying a whole bunch of different settings throughout the troubleshooting process. I will also note that we're using ASDM as our primary method of configuring the unit, so any suggestions that could be made with that in mind would be most helpful. Thanks!
ASA-01# sh run
: Saved
ASA Version 8.6(1)2
hostname ASA-01
domain-name domain.org
enable password **** encrypted
passwd **** encrypted
names
interface GigabitEthernet0/0
speed 100
duplex full
nameif inside
security-level 100
ip address 10.2.0.1 255.255.0.0
interface GigabitEthernet0/1
description Primary WAN Interface
nameif outside
security-level 0
ip address 76.232.211.169 255.255.255.192
interface GigabitEthernet0/2
shutdown
<--- More --->
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
speed 100
<--- More --->
duplex full
shutdown
nameif management
security-level 100
ip address 10.4.0.1 255.255.0.0
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns server-group DefaultDNS
name-server 10.2.11.6
domain-name domain.org
dns server-group sub
name-server 10.2.11.121
name-server 10.2.11.138
domain-name sub.domain.net
same-security-traffic permit intra-interface
object network 76.232.211.132
host 76.232.211.132
object network 10.2.11.138
host 10.2.11.138
object network 10.2.11.11
host 10.2.11.11
<--- More --->
object service DB91955443
service tcp destination eq 55443
object service 113309
service tcp destination range 3309 8088
object service 11443
service tcp destination eq https
object service 1160001
service tcp destination range 60001 60008
object network LAN
subnet 10.2.0.0 255.255.0.0
object network WAN_PAT
host 76.232.211.170
object network Test
host 76.232.211.169
description test
object network NETWORK_OBJ_10.2.0.0_16
subnet 10.2.0.0 255.255.0.0
object network NETWORK_OBJ_10.2.250.0_24
subnet 10.2.250.0 255.255.255.0
object network VPN_In
subnet 10.3.0.0 255.255.0.0
description VPN User Network
object-group service 11
service-object object 113309
<--- More --->
service-object object 11443
service-object object 1160001
object-group service IPSEC_VPN udp
port-object eq 4500
port-object eq isakmp
access-list outside_access_in extended permit icmp object VPN_In 10.2.0.0 255.255.0.0 traceroute log disable
access-list outside_access_in extended permit object-group 11 object 76.232.211.132 interface outside
access-list outside_access_in extended permit object DB91955443 any interface outside
access-list outside_access_in extended permit udp any object Test object-group IPSEC_VPN inactive
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any
access-list inside_access_in extended permit ip any any log disable
access-list inside_access_in extended permit icmp any any echo-reply log disable
access-list inside_access_in extended permit ip object VPN_In 10.2.0.0 255.255.0.0 log disable
access-list domain_splitTunnelAcl standard permit 10.2.0.0 255.255.0.0
access-list domain_splitTunnelAcl standard permit 10.3.0.0 255.255.0.0
access-list vpn_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool VPNUsers 10.3.0.1-10.3.0.254 mask 255.255.0.0
<--- More --->
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any management
icmp permit any inside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic any interface
nat (inside,outside) source dynamic any WAN_PAT inactive
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 113309 113309
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 11443 11443
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 1160001 1160001
nat (outside,outside) source static any any destination static interface 10.2.11.138 service DB91955443 DB91955443
nat (inside,outside) source static NETWORK_OBJ_10.2.0.0_16 NETWORK_OBJ_10.2.0.0_16 destination static NETWORK_OBJ_10.2.250.0_24 NETWORK_OBJ_10.2.250.0_24 no-proxy-arp route-lookup
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 76.232.211.129 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
<--- More --->
dynamic-access-policy-record DfltAccessPolicy
aaa-server ActiveDirectory protocol nt
aaa-server ActiveDirectory (inside) host 10.2.11.121
nt-auth-domain-controller sub.domain.net
aaa-server ActiveDirectory (inside) host 10.2.11.138
nt-auth-domain-controller sub.domain.net
user-identity default-domain LOCAL
eou allow none
http server enable
http 10.4.0.0 255.255.255.0 management
http 10.2.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
no sysopt connection permit-vpn
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
<--- More --->
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
<--- More --->
subject-name CN=ASA-01
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate a6c98751
308201f1 3082015a a0030201 020204a6 c9875130 0d06092a 864886f7 0d010105
0500303d 31153013 06035504 03130c43 5248442d 4d432d46 57303131 24302206
092a8648 86f70d01 09021615 43524844 2d4d432d 46573031 2e637268 642e6f72
67301e17 0d313330 35303730 32353232 325a170d 32333035 30353032 35323232
5a303d31 15301306 03550403 130c4352 48442d4d 432d4657 30313124 30220609
2a864886 f70d0109 02161543 5248442d 4d432d46 5730312e 63726864 2e6f7267
30819f30 0d06092a 864886f7 0d010101 05000381 8d003081 89028181 00c23d5f
acbf2b3f 9fe6e3c9 1866c344 07b6ee49 f6f31798 0b87a38b 890f70e2 c28cc1d5
fd1b4e80 7fa25483 09e79459 6bf92155 c55240b4 93eeb4eb af3f8aec 8906ef48
140c57bb 5ca4471f 275c1932 7e90976f f0dfe8a3 04a7861f cce7a320 7267df2e
61f9b6b8 22bb70ac d9cedb73 3cf9747b c2636892 48b35385 a94bfae5 fd020301
0001300d 06092a86 4886f70d 01010505 00038181 003c7e16 be4aff40 8fe69a31
acf31808 680e44eb 8ede9094 f9a4a147 0ae18cdc 000dc07f c1da1af4 a2d964ed
288689ee 95179ad0 90728324 9803248d b9d10641 01897453 fe7fafcd 34dee13a
92798615 4acb1f27 14fdb346 ab3eb825 04f23791 81d08fa2 b54c6a47 aedd9694
1c9fbcb4 455fd5ce 420298aa 9333737c 19f0e715 50
quit
crypto isakmp identity address
crypto isakmp nat-traversal 30
crypto ikev2 policy 1
<--- More --->
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
<--- More --->
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev2 remote-access trustpoint ASDM_TrustPoint0
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
<--- More --->
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
<--- More --->
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
<--- More --->
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
<--- More --->
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd dns 10.2.11.121 10.2.11.138
dhcpd lease 36000
dhcpd ping_timeout 30
dhcpd domain sub.domain.net
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint0 outside
webvpn
<--- More --->
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect profiles VPN_client_profile disk0:/VPN_client_profile.xml
anyconnect enable
tunnel-group-list enable
group-policy domain internal
group-policy domain attributes
banner value You are attempting to access secured systems at thsi facility. All activity is monitored and recorded. Disconnect now if you are not authorized to access these systems or do not possess valid logon credentials.
wins-server value 10.2.11.121 10.2.11.138
dns-server value 10.2.11.121 10.2.11.138
vpn-idle-timeout none
vpn-filter value vpn_access_in
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value domain_splitTunnelAcl
default-domain value sub.domain.net
split-dns value sub.domain.net
group-policy DfltGrpPolicy attributes
dns-server value 10.2.11.121 10.2.11.138
vpn-filter value outside_access_in
vpn-tunnel-protocol l2tp-ipsec
default-domain value sub.domain.net
split-dns value sub.domain.net
address-pools value VPNUsers
username **** password **** encrypted privilege 15
<--- More --->
username **** password **** encrypted privilege 15
username **** attributes
webvpn
anyconnect keep-installer installed
anyconnect dtls compression lzs
anyconnect ssl dtls enable
anyconnect profiles value VPN_client_profile type user
tunnel-group DefaultL2LGroup general-attributes
default-group-policy domain
tunnel-group DefaultRAGroup general-attributes
address-pool VPNUsers
authentication-server-group ActiveDirectory
default-group-policy domain
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
ikev1 trust-point ASDM_TrustPoint0
tunnel-group DefaultWEBVPNGroup general-attributes
default-group-policy domain
tunnel-group domain type remote-access
tunnel-group domain general-attributes
address-pool (inside) VPNUsers
address-pool VPNUsers
authentication-server-group ActiveDirectory LOCAL
authentication-server-group (inside) ActiveDirectory LOCAL
<--- More --->
default-group-policy domain
dhcp-server link-selection 10.2.11.121
tunnel-group domain ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
<--- More --->
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly 21
subscribe-to-alert-group configuration periodic monthly 21
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:2578e19418cb5c61eaf15e9e2e5338a0
: endHello,
I've been working on this issue for a few days with no success. We're setting up a new Cisco ASA 5515 in our environment and are trying to get a simple IPSec VPN setup on it for remote access. After some initial problems, we've gotten it to where the VPN tunnel authenticates the user and connects as it should, however we cannot ping into our LAN. We are able to ping as far as the firewall's inside interface. I've tried other types of traffic too and nothing gets through. I've checked the routes listed on the VPN client while we're connected and they look correct - the client also shows both sent and received bytes when we connect using TCP port 10000, but no Received bytes when we connect using UDP 4500. We are trying to do split tunneling, and that seems to be setup correctly because I can still surf while the VPN is connected.
Below is our running config. Please excuse any messyness in the config as there are a couple of us working on it and we've been trying a whole bunch of different settings throughout the troubleshooting process. I will also note that we're using ASDM as our primary method of configuring the unit, so any suggestions that could be made with that in mind would be most helpful. Thanks!
ASA-01# sh run
: Saved
ASA Version 8.6(1)2
hostname ASA-01
domain-name domain.org
enable password **** encrypted
passwd **** encrypted
names
interface GigabitEthernet0/0
speed 100
duplex full
nameif inside
security-level 100
ip address 10.2.0.1 255.255.0.0
interface GigabitEthernet0/1
description Primary WAN Interface
nameif outside
security-level 0
ip address 76.232.211.169 255.255.255.192
interface GigabitEthernet0/2
shutdown
<--- More --->
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
speed 100
<--- More --->
duplex full
shutdown
nameif management
security-level 100
ip address 10.4.0.1 255.255.0.0
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns server-group DefaultDNS
name-server 10.2.11.6
domain-name domain.org
dns server-group sub
name-server 10.2.11.121
name-server 10.2.11.138
domain-name sub.domain.net
same-security-traffic permit intra-interface
object network 76.232.211.132
host 76.232.211.132
object network 10.2.11.138
host 10.2.11.138
object network 10.2.11.11
host 10.2.11.11
<--- More --->
object service DB91955443
service tcp destination eq 55443
object service 113309
service tcp destination range 3309 8088
object service 11443
service tcp destination eq https
object service 1160001
service tcp destination range 60001 60008
object network LAN
subnet 10.2.0.0 255.255.0.0
object network WAN_PAT
host 76.232.211.170
object network Test
host 76.232.211.169
description test
object network NETWORK_OBJ_10.2.0.0_16
subnet 10.2.0.0 255.255.0.0
object network NETWORK_OBJ_10.2.250.0_24
subnet 10.2.250.0 255.255.255.0
object network VPN_In
subnet 10.3.0.0 255.255.0.0
description VPN User Network
object-group service 11
service-object object 113309
<--- More --->
service-object object 11443
service-object object 1160001
object-group service IPSEC_VPN udp
port-object eq 4500
port-object eq isakmp
access-list outside_access_in extended permit icmp object VPN_In 10.2.0.0 255.255.0.0 traceroute log disable
access-list outside_access_in extended permit object-group 11 object 76.232.211.132 interface outside
access-list outside_access_in extended permit object DB91955443 any interface outside
access-list outside_access_in extended permit udp any object Test object-group IPSEC_VPN inactive
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any
access-list inside_access_in extended permit ip any any log disable
access-list inside_access_in extended permit icmp any any echo-reply log disable
access-list inside_access_in extended permit ip object VPN_In 10.2.0.0 255.255.0.0 log disable
access-list domain_splitTunnelAcl standard permit 10.2.0.0 255.255.0.0
access-list domain_splitTunnelAcl standard permit 10.3.0.0 255.255.0.0
access-list vpn_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool VPNUsers 10.3.0.1-10.3.0.254 mask 255.255.0.0
<--- More --->
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any management
icmp permit any inside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic any interface
nat (inside,outside) source dynamic any WAN_PAT inactive
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 113309 113309
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 11443 11443
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 1160001 1160001
nat (outside,outside) source static any any destination static interface 10.2.11.138 service DB91955443 DB91955443
nat (inside,outside) source static NETWORK_OBJ_10.2.0.0_16 NETWORK_OBJ_10.2.0.0_16 destination static NETWORK_OBJ_10.2.250.0_24 NETWORK_OBJ_10.2.250.0_24 no-proxy-arp route-lookup
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 76.232.211.129 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
<--- More --->
dynamic-access-policy-record DfltAccessPolicy
aaa-server ActiveDirectory protocol nt
aaa-server ActiveDirectory (inside) host 10.2.11.121
nt-auth-domain-controller sub.domain.net
aaa-server ActiveDirectory (inside) host 10.2.11.138
nt-auth-domain-controller sub.domain.net
user-identity default-domain LOCAL
eou allow none
http server enable
http 10.4.0.0 255.255.255.0 management
http 10.2.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
no sysopt connection permit-vpn
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
<--- More --->
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
<--- More --->
subject-name CN=ASA-01
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate a6c98751
308201f1 3082015a a0030201 020204a6 c9875130 0d06092a 864886f7 0d010105
0500303d 31153013 06035504 03130c43 5248442d 4d432d46 57303131 24302206
092a8648 86f70d01 09021615 43524844 2d4d432d 46573031 2e637268 642e6f72
67301e17 0d313330 35303730 32353232 325a170d 32333035 30353032 35323232
5a303d31 15301306 03550403 130c4352 48442d4d 432d4657 30313124 30220609
2a864886 f70d0109 02161543 5248442d 4d432d46 5730312e 63726864 2e6f7267
30819f30 0d06092a 864886f7 0d010101 05000381 8d003081 89028181 00c23d5f
acbf2b3f 9fe6e3c9 1866c344 07b6ee49 f6f31798 0b87a38b 890f70e2 c28cc1d5
fd1b4e80 7fa25483 09e79459 6bf92155 c55240b4 93eeb4eb af3f8aec 8906ef48
140c57bb 5ca4471f 275c1932 7e90976f f0dfe8a3 04a7861f cce7a320 7267df2e
61f9b6b8 22bb70ac d9cedb73 3cf9747b c2636892 48b35385 a94bfae5 fd020301
0001300d 06092a86 4886f70d 01010505 00038181 003c7e16 be4aff40 8fe69a31
acf31808 680e44eb 8ede9094 f9a4a147 0ae18cdc 000dc07f c1da1af4 a2d964ed
288689ee 95179ad0 90728324 9803248d b9d10641 01897453 fe7fafcd 34dee13a
92798615 4acb1f27 14fdb346 ab3eb825 04f23791 81d08fa2 b54c6a47 aedd9694
1c9fbcb4 455fd5ce 420298aa 9333737c 19f0e715 50
quit
crypto isakmp identity address
crypto isakmp nat-traversal 30
crypto ikev2 policy 1
<--- More --->
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
<--- More --->
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev2 remote-access trustpoint ASDM_TrustPoint0
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
<--- More --->
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
<--- More --->
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
<--- More --->
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
<--- More --->
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd dns 10.2.11.121 10.2.11.138
dhcpd lease 36000
dhcpd ping_timeout 30
dhcpd domain sub.domain.net
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint0 outside
webvpn
<--- More --->
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect profiles VPN_client_profile disk0:/VPN_client_profile.xml
anyconnect enable
tunnel-group-list enable
group-policy domain internal
group-policy domain attributes
banner value You are attempting to access secured systems at thsi facility. All activity is monitored and recorded. Disconnect now if you are not authorized to access these systems or do not possess valid logon credentials.
wins-server value 10.2.11.121 10.2.11.138
dns-server value 10.2.11.121 10.2.11.138
vpn-idle-timeout none
vpn-filter value vpn_access_in
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value domain_splitTunnelAcl
default-domain value sub.domain.net
split-dns value sub.domain.net
group-policy DfltGrpPolicy attributes
dns-server value 10.2.11.121 10.2.11.138
vpn-filter value outside_access_in
vpn-tunnel-protocol l2tp-ipsec
default-domain value sub.domain.net
split-dns value sub.domain.net
address-pools value VPNUsers
username **** password **** encrypted privilege 15
<--- More --->
username **** password **** encrypted privilege 15
username **** attributes
webvpn
anyconnect keep-installer installed
anyconnect dtls compression lzs
anyconnect ssl dtls enable
anyconnect profiles value VPN_client_profile type user
tunnel-group DefaultL2LGroup general-attributes
default-group-policy domain
tunnel-group DefaultRAGroup general-attributes
address-pool VPNUsers
authentication-server-group ActiveDirectory
default-group-policy domain
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
ikev1 trust-point ASDM_TrustPoint0
tunnel-group DefaultWEBVPNGroup general-attributes
default-group-policy domain
tunnel-group domain type remote-access
tunnel-group domain general-attributes
address-pool (inside) VPNUsers
address-pool VPNUsers
authentication-server-group ActiveDirectory LOCAL
authentication-server-group (inside) ActiveDirectory LOCAL
<--- More --->
default-group-policy domain
dhcp-server link-selection 10.2.11.121
tunnel-group domain ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
<--- More --->
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly 21
subscribe-to-alert-group configuration periodic monthly 21
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:2578e19418cb5c61eaf15e9e2e5338a0
: end -
Dynamin VPN/GRE can't ping other side of tunnel
I am new at this VPN stuff and tryiong to setup a GRE Dynamic IP VPN between my offfice and home. Here is what I ahve done thus far:
OFFICE
interface Tunnel0
ip address 172.30.1.1 255.255.255.252
no ip redirects
ip mtu 1400
ip nhrp map multicast dynamic
ip nhrp network-id 1
ip tcp adjust-mss 1360
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 1
interface FastEthernet0/0
ip address 40.197.68.9 255.255.255.248
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
HOME
interface Tunnel0
ip address 172.30.1.2 255.255.255.252
ip mtu 1400
ip nhrp map multicast 40.197.68.9
ip nhrp map 172.30.1.1 40.197.68.9
ip nhrp network-id 1
ip nhrp nhs 172.30.1.1
ip tcp adjust-mss 1360
tunnel source GigabitEthernet0/0
tunnel destination 40.197.68.9
tunnel key 1
interface GigabitEthernet0/0
description Router
ip address 192.168.30.1 255.255.255.252
duplex auto
speed auto
When I ping 172.30.1.1 from the HOME router, I get 0/5 success. Not good! I have not setup any IPSec yet.
Results for HOME router
show ip nhrp nhs detail
Legend: E=Expecting replies, R=Responding, W=Waiting
Tunnel0:
172.30.1.1 E priority = 0 cluster = 0 req-sent 53 req-failed 0 repl-recv 0
sh int t0
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Internet address is 172.30.1.2/30
MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 192.168.30.1 (GigabitEthernet0/0), destination 40.197.68.9
Tunnel Subblocks:
src-track:
Tunnel0 source tracking subblock associated with GigabitEthernet0/0
Set of tunnels with source GigabitEthernet0/0, 1 member (includes iterators), on interface <OK>
Tunnel protocol/transport GRE/IP
Key 0x1, sequencing disabled
Checksumming of packets disabled
Tunnel TTL 255, Fast tunneling enabled
Tunnel transport MTU 1472 bytes
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
Last input 00:40:28, output 00:00:25, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
106 packets output, 12612 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
sh ip route
Gateway of last resort is 192.168.30.2 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 192.168.30.2
10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
C 10.110.0.0/24 is directly connected, GigabitEthernet0/1.110
L 10.110.0.1/32 is directly connected, GigabitEthernet0/1.110
C 10.115.0.0/24 is directly connected, GigabitEthernet0/1.115
L 10.115.0.1/32 is directly connected, GigabitEthernet0/1.115
172.16.0.0/30 is subnetted, 1 subnets
S 172.16.2.0 [1/0] via 192.168.30.6
172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.30.1.0/30 is directly connected, Tunnel0
L 172.30.1.2/32 is directly connected, Tunnel0
S 192.168.2.0/24 is directly connected, GigabitEthernet0/0
S 192.168.10.0/24 is directly connected, GigabitEthernet0/0
192.168.30.0/24 is variably subnetted, 4 subnets, 2 masks
C 192.168.30.0/30 is directly connected, GigabitEthernet0/0
L 192.168.30.1/32 is directly connected, GigabitEthernet0/0
C 192.168.30.4/30 is directly connected, GigabitEthernet0/1.30
L 192.168.30.5/32 is directly connected, GigabitEthernet0/1.30
S 192.168.50.0/24 [1/0] via 192.168.30.6
192.168.69.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.69.0/24 is directly connected, GigabitEthernet0/1.69
L 192.168.69.3/32 is directly connected, GigabitEthernet0/1.69
S 192.168.100.0/24 [1/0] via 192.168.30.6
S 192.168.125.0/24 [1/0] via 192.168.30.6
S 192.168.200.0/24 [1/0] via 192.168.30.6
sh dmvpn
Interface: Tunnel0, IPv4 NHRP Details
Type:Spoke, NHRP Peers:1,
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb
1 50.197.68.90 172.30.1.1 NHRP 02:30:17 S
Results for OFFICE router
show ip nhrp nhs detail
sh dmvpn
sh int t0
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Internet address is 172.30.1.1/30
MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 40.197.68.9 (FastEthernet0/0)
Tunnel Subblocks:
src-track:
Tunnel0 source tracking subblock associated with FastEthernet0/0
Set of tunnels with source FastEthernet0/0, 1 member (includes iterators), on interface <OK>
Tunnel protocol/transport multi-GRE/IP
Key 0x1, sequencing disabled
Checksumming of packets disabled
Tunnel TTL 255, Fast tunneling enabled
Tunnel transport MTU 1472 bytes
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
Last input 00:43:56, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
show ip route
S* 0.0.0.0/0 [1/0] via 40.197.68.94
40.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 40.197.68.8/29 is directly connected, FastEthernet0/0
L 40.197.68.9/32 is directly connected, FastEthernet0/0
172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.30.1.0/30 is directly connected, Tunnel0
L 172.30.1.1/32 is directly connected, Tunnel0
S 192.168.2.0/24 [1/0] via 192.168.10.5
192.168.10.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.10.0/24 is directly connected, FastEthernet0/1
L 192.168.10.1/32 is directly connected, FastEthernet0/1
S 192.168.69.0/24 is directly connected, FastEthernet0/0
Why can't Io ping from the HOME router to the OFFICE router?I fugured this problem out. I needed to setup PKI/IKE and once that was done on both routers, my tunned now passes some data.
-
I am a developer getting started with Solaris 10 configuration. I recently installed Solaris 10 and have run into an issue with network connectivity.
I have done much research on this and I was able to get communiction to the internet established once, but the settings were lost on reboot.
Overview - The Solaris box is connected to a router which is acting as a DHCP server.
AMD 64 dual 2.6
nForce4+ integrated NIC
1) I am not able to obtain an address from the router. Nor do I get a respons back when I ping it. I get an IP etc if I boot into Windows so phyicial connectivity is fine.
2) Upon reboot the device nfo0 as shown using ifconfig -a has an IP of 0.0.0.0.
3) If I run ifconfig [hostname] my machine gets the ip from the hosts file, but I would like to obtain this from the router.
4) NOTE - the machine shows as active on my router, but the Solaris box cannot be reached from other computers on the networ, nor do I get a reply back when pinging the router from the Solaris box.
GOAL - reach and obtain a DHCP from the router and have the changes stick upon reboot.
/etc/hosts contents
127.0.0.1 localhost loghost
192.168.1.55 solarisX /*<-- this is what I get when I do ifconfig nfo0 solarisX */
/etc/hosname.nfo0
netmask + 255.255.255.0
solarisX
/etc/defaultrouter
192.168.1.254
/et c/netmasks
192.168.0.0 255.255.2550
Specific Steps taken:
Using the driver nfo-2.4.5 locate at http://homepage2.nifty.com/mrym3/taiyodo/eng/ I did the following.
% cd /.../nfo-x.x.x
% rm obj Makefile
% ln -s Makefile.${KARCH}_${COMPILER} Makefile
% ln -s ${KARCH} obj
where ${KARCH} is the result of `isainfo -n`, and ${COMPILER} is
"gcc" or "suncc" which you want to use to make the driver.
4. Testing
Testing before installation is strongly recommended.
# cd /.../nfo-x.x.x
# /usr/ccs/bin/make install
# ./adddrv.sh
# /usr/ccs/bin/make uninstall (for solaris7, don't remove the file )
# modload obj/nfo
# devfsadm -i nfo (for solaris7, use drvconfig and reboot with -r )
# ifconfig nfoN plumb ( where N is an instance number, typcally 0 for first card)
# ifconfig -a ( you will see an entry for nfoN)
# ifconfig nfoN YOUR-HOST-NAME
# ifconfig nfoN ( ensure IP address is correct)
# ifconfig nfoN up ( and then you can test with ping, telnet, ftp ...)
5. Installation
After you ensure that the nfo driver is fully functional, install it.
(1) copy the nfo driver into the kernel directory
# cd /.../nfo-x.x.x
# /usr/ccs/bin/make install
If you do not test the nfo driver yet, execute the following commands:
# ./adddrv.sh
# devfsadm -i nfo (for solaris7, use drvconfig and reboot with -r)
(2) Configure the network interface. Create and/or modify the following file:
/etc/hostname.nfoN
(3) Reboot the system.
# init 6
Edited by: hedger on Nov 16, 2007 11:17 PMThanks Alan. I worked on trying to get the NIC working again last night. I had it working once, although the settings did not perist. I can still get the device to load, but I can't communciate with the router (it's not physical because another OS can reach it.
I took your advice and tried the sys-unconfig. But I did not have much success.
I am wondering if plopping in a new PCI NIC would be the most efficient route to get the server up.
What kind of NIC do you utilize and have had success with?
I am looking at possibly a DLINK DFE-530 or NetGear FA-311. I don't need wireless at this point just a rock solid DEV box.
Thanks again for the previous info.
Ted -
VPN Problem: Can't route to other network clients
Hi,
I can't ping the other clients on the network when I'm connected to VPN from outside.
But accessing internet trough VPN works. (Sending all data through VPN).
So in fact, I can only ping the VPN server I'm connected to.
Maybe someone here has an idea what I'm doing wrong here.
Here is my setup:
internet
I
I
Airport Extreme (internal IP 192.168.3.1, Router with NAT Port forwarding to 192.168.3.3)
I
I
Switch----macMini (192.168.3.3, OS X Server 10.4.10 with VPN, DHCP, DNS, NAT enabled)
l
l
Other Clients on the Network (Clients have DNS entry 192.168.3.3 192.168.3.1, Router is 192.168.3.1)
The services DHCP, DNS working well for internal clients.
Has someone an idea?
Thanks a lot.
Alex
Message was edited by: SyndromeFirst, ping is ICMP traffic, different from other kinds of (eg, TCP) traffic like AFP.
See http://www.cisco.com/en/US/products/sw/iosswrel/ps1831/productstechnote09186a00800a6057.shtml
traceroute also uses some ICMP traffic but might also be using UDP, see
http://en.wikipedia.org/wiki/Traceroute
http://www.linuxplanet.com/linuxplanet/tutorials/6524/1/
However, in testing, I can indeed ping the server, when I connect to a remote Mac OS X Server via the Mac OS X supplied vpn. But there is no AP Extreme in the path. So the two big factors are: limitations and/or configuration of the AP, and firewall settings for each/any machine involved.
The Airport Extreme is really quite limited, compared to any more full-featured routing device - in terms of just how granular you can be with controlling traffic flow.
(As a total aside, I'd recommend investing in something like a Zyxel Zywall 2 Plus (or similar or better) and running the AP in bridge mode for wireless clients.)
When you've connected via VPN, please run
netstat -rn to see what your default gateway is, that's actually being used.
Finally, what led you to try these tests ? What other problems are you having, what primary issue(s) are you trying to solve ? -
Fresh BW Installation : You Can Only Work in Client 001
Hello All,
I am doing a BI 7.4 installation.
Till now i have just installed NW7.4 ABAP system. I did some of post processing steps after installation like STMS, SGEN.. etc.
We want to have client 100 for BI usage. So i created 100 client with client copy with SAP_CUST profile.. is this corrrect ?
Now i have 2 question..
1. When i run RSA1 in 100 client, I get error "You Can Only Work in Client 001" ? Did i performed wrong client copy ? What is correct procedure. I do not find anything in Installation guide for NW.
2. I need to deploy BI_CONT addon. I can do this with SAINT.. is there some post activity.. which activate something ?
best regards
ashishHi
1. When i run RSA1 in 100 client, I get error "You Can Only Work in Client 001" ? Did i performed wrong client copy ? What is correct procedure. I do not find anything in Installation guide for NW.
Kindly refer the SAP Note 316923 - Termination of program RS_CLIENT_COPY_BW
2. I need to deploy BI_CONT addon. I can do this with SAINT.. is there some post activity.. which activate something ?
Kindly refer the SAP Note 153967 - BI Content Release Strategy
1808103 - BI_CONT 737/747 SP04 and higher: Information on Add-On SPs
1808103 - BI_CONT 737/747 SP04 and higher: Information on Add-On SPs
BR
SS -
Clients behind shared wireless can only connect one at a time to RV042
I am using a RV042 HW version 3 (black front panel and blue user interface).
I have have 2 vpn users who share an apartment.
They use a wireless router to get to the internet.
Both use Windows 7 (firewall enabled) and the latest QuickVPN client.
As it is, only one of the users can connect at the same time.
When one is already connected the other gets a message "the remote gateway is not responding"
Has anyone else experienced something like this ?
Thanks in advance.
These are the logs from the PC that connected ok:
From wget_stop_error.txt
--10:29:50-- https://Serena:*password*@180.243.235.82/StopConnection.htm?version=1?status=disable?IP=192.168.0.101?PASSWD=*password*?USER=Serena
=> `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//stopconn.conf'
Connecting to 180.243.235.82:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: unspecified [text/html]
0K 96.68 KB/s
10:29:50 (96.68 KB/s) - `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//stopconn.conf' saved [99]
From wget_request_error.txt
--10:29:45-- https://Serena:*password*@www.vantagebanking.com:60443/CheckIsakmp.htm?version=1?IP=192.168.0.101?PASSWD=*password*?USER=Serena*password*@www.vantagebanking.com:60443/CheckIsakmp.htm?version=1?IP=192.168.0.101?PASSWD=*password*?USER=Serena
=> `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//isakmp_status.conf'
Resolving www.vantagebanking.com... 180.243.235.82
Connecting to www.vantagebanking.com[180.243.235.82]:60443... connected.
HTTP request sent, awaiting response...
End of file while parsing headers.
Giving up.
From wget_error.txt
--10:29:13-- https://Serena:*password*@180.243.235.82/StartConnection.htm?version=1?IP=192.168.0.101?PASSWD=*password*?USER=Serena
=> `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//vpnserver.conf'
Connecting to 180.243.235.82:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: unspecified [text/html]
0K 176.76 KB/s
10:29:14 (176.76 KB/s) - `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//vpnserver.conf' saved [181]
From Log.txt
2011/07/16 10:29:12 [STATUS]OS Version: Windows 7
2011/07/16 10:29:12 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/07/16 10:29:12 [STATUS]Windows Firewall Private Profile Settings: ON
2011/07/16 10:29:12 [STATUS]Windows Firewall Private Profile Settings: ON
2011/07/16 10:29:12 [STATUS]One network interface detected with IP address 192.168.0.101
2011/07/16 10:29:12 [STATUS]Connecting...
2011/07/16 10:29:12 [DEBUG]Input VPN Server Address = www.vantagebanking.com
2011/07/16 10:29:13 [STATUS]Connecting to remote gateway with IP address: 180.243.235.82
2011/07/16 10:29:14 [STATUS]Remote gateway was reached by https ...
2011/07/16 10:29:14 [STATUS]Provisioning...
2011/07/16 10:29:24 [STATUS]Success to connect.
2011/07/16 10:29:24 [STATUS]Tunnel is configured. Ping test is about to start.
2011/07/16 10:29:24 [STATUS]Verifying Network...
2011/07/16 10:29:30 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:33 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:36 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:39 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:42 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:29:45 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
2011/07/16 10:29:49 [STATUS]Disconnecting...
2011/07/16 10:29:53 [WARNING]Failed to disconnect.
And these are the ones from PC # 2 which failed to connect with error "The remote gateway is not responding"
This error just keeps looping around
From wget_error.txt
--10:29:21-- https://Paul:*password*@180.243.235.82/StartConnection.htm?version=1?IP=192.168.0.100?PASSWD=*password*?USER=Paul
=> `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//vpnserver.conf'
Connecting to 180.243.235.82:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: unspecified [text/html]
0K 174.80 KB/s
10:29:22 (174.80 KB/s) - `C://Program Files (x86)//Cisco Small Business//QuickVPN Client//vpnserver.conf' saved [179]
From Log.txt
2011/07/16 10:29:18 [STATUS]OS Version: Windows 7
2011/07/16 10:29:18 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/07/16 10:29:18 [STATUS]Windows Firewall Private Profile Settings: ON
2011/07/16 10:29:18 [STATUS]Windows Firewall Private Profile Settings: ON
2011/07/16 10:29:18 [STATUS]One network interface detected with IP address 192.168.0.100
2011/07/16 10:29:18 [STATUS]Connecting...
2011/07/16 10:29:18 [DEBUG]Input VPN Server Address = www.vantagebanking.com
2011/07/16 10:29:20 [STATUS]Connecting to remote gateway with IP address: 180.243.235.82
2011/07/16 10:29:22 [STATUS]Remote gateway was reached by https ...
2011/07/16 10:29:22 [STATUS]Provisioning...
2011/07/16 10:29:32 [STATUS]Success to connect.
2011/07/16 10:29:32 [STATUS]Tunnel is configured. Ping test is about to start.
2011/07/16 10:29:32 [STATUS]Verifying Network...
2011/07/16 10:29:38 [WARNING]Failed to ping remote VPN Router!
2011/07/16 10:30:51 [WARNING]Failed to ping remote VPN Router!I just removed the tunnel and after that I cannot log in any more.
I rebooted the router after removing the tunnel.
I have tried many times.
I use remote management from Singapore with the RV042 in Jakarta.
Other users also cannot log in.
"Verifying network" is as far as we get.
This is the log:
2011/07/19 14:54:06 [STATUS]OS Version: Windows XP
2011/07/19 14:54:06 [STATUS]Windows Firewall is OFF
2011/07/19 14:54:07 [STATUS]One network interface detected with IP address 10.71.11.9
2011/07/19 14:54:07 [STATUS]Connecting...
2011/07/19 14:54:07 [DEBUG]Input VPN Server Address = 180.243.235.82
2011/07/19 14:54:07 [STATUS]Connecting to remote gateway with IP address: 180.243.235.82
2011/07/19 14:54:09 [STATUS]Remote gateway was reached by https ...
2011/07/19 14:54:09 [STATUS]Provisioning...
2011/07/19 14:54:19 [STATUS]Success to connect.
2011/07/19 14:54:19 [STATUS]Tunnel is configured. Ping test is about to start.
2011/07/19 14:54:19 [STATUS]Verifying Network...
2011/07/19 14:54:23 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:24 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:25 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:26 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:27 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:28 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
2011/07/19 14:54:37 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:38 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:39 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:40 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:42 [WARNING]Failed to ping remote VPN Router!
2011/07/19 14:54:42 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
I have restored from the export .config file and all is back to normal.
So I better leave the single tunnel as it is.
I will try with spare RV042 when I am back in Jakarta
Maybe you are looking for
-
[JS][CS3]how to get refrence for source file
Hi All I am new and learning javascript Gradually Could any one help on this as i do have a code for load style but don't know how to get refrence for "source file" and "targetDoc" targetDoc.importStyles(charImport, sourceFile, clashPolicy); targetDo
-
Aperture 3: Geotagged Photos show up in wrong part of world
I imported a set of geotagged photos. When I look at places in Aperture 3 several of the photos are appearing in the wrong part of the world ( Kazakhstan instead of Nova Scotia). The photos were taken / geotagged by my Blackberry Storm. When I travel
-
Hi All, MWST condition type is only available in Purchasing pricing procedure MM not in Tax procedure under FI. 1) How can i use this condition type & post value to VST key. 2) should i include MWST in Tax procedure also. Pls advise how to use this
-
Hi all. I'm on devsuite 10g. Is there a way to set the data type property of an item at runtime??? Thanks all for the collaboration, Fabrizio
-
How to delete photos on iPad2 without deleting all of the same photo?
How can a photo be deleted on an iPad2 without deleting all other photos in other albums?