RADIUS from Aironet 1231 - enable fails
Hi all,
we have an ACS server (3.3)
which we use for Login and Enable authentication for all our routers & switches without any problems.
I am setting up an Aironet 1231G with IOS 12.3(7)JA
I am able to get the login to authenticate OK, but when you try to enable, it returns "REJECTED".
the ACS Failed Attempts.csv shows the following:
06/09/2005 15:59:00 Authen failed $enab15$ .. .. External DB auth failed .. .. 0 10.139.251.201
Can anyone please tell me what I'm doing wrong?
Aironet Startup-config is attached
Many Thanks.
Thanks for the response, but Tacacs didn't work either.
We eventually figured it out.. we'd missed off the
aaa authentication enable default group radius enable
command.
added this and all was well.
Cheers,
Nick
Similar Messages
-
I have one Cisco Aironet 1231 access point. It does not use any kind of (server) functionality outside the Cisco device.
I have one SSID and uses WPA-PSK (TKIP).
The configuration seams wary straight forward, but something is wrong.
The access point seams to be unstable. The clients use long time to connect to the access point and it looses connection a lot of times a day. Can I do something to speed up the ?negotiation process? ?
What could be the course of instability?
The configuration was made with the ?web configurator?, but I have a SSH/telnet dump:
Best Regards
Martin
AP1#sh run
Building configuration...
Current configuration : 2227 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1
enable secret xxx
clock timezone GMT 1
ip subnet-zero
ip domain name mydom.com
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 ssid myssid
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii xxx
username Cisco password xxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid myssid
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2412
station-role root
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no cdp enable
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
hold-queue 160 in
interface BVI1
ip address 192.168.1.105 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
access-list 111 permit tcp any any neq telnet
no cdp run
radius-server local
no authentication leap
no authentication mac
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
control-plane
bridge 1 route ip
line con 0
access-class 111 in
line vty 0 4
access-class 111 in
sntp server 212.242.xx.207
sntp broadcast client
end
AP1#A "stronger" (more gain) antenna probably won't help. An antenna that transmits with more gain also receives with more gain ..(basically, the same situation, but all of the signals are "louder")
The general remedy, aside from the obvious of going to the least populated channel or moving to the 802.11a band, is usually to add more access points, all using some flavor of "sector" antenna (and / or "patch" antennas) to localize the area of interest.
Because the antennas are covering a more specific area (and usually smaller area), it is usually the case that more APs are needed.
"Seeing" 20 APs is not that alarming ... check the signal strength of each, many will usually be well-below the level that would cause serious interference. The specific level will vary, depending on the location relative to the AP<->client relationship.
If you're seeing 20 APs, and their signal strength is roughly the same as your APs or a little lower, then you've got a problem that only a sectorized antenna system can cure.
Good Luck
Scott -
Rate-limit for some MAC on aironet 1231
Hello!
I need to set rate-limit for some mac addresses on access point aironet 1231.Is it possible?
If no, what ios or devices can do it?
Thanks.No there is no option for rate-limit in Aironet but in controller, Rate-limiting is applicable to all traffic destined to the CPU from either direction (wireless or wired). Cisco recommends that you always run the controller with the default config advanced rate enable command in effect in order to rate-limit traffic to the controller and protect against denial-of-service (DoS) attacks. You can use the config advanced rate disable command to stop rate-limiting of Internet Control Message Protocol (ICMP) echo responses for testing purposes.
-
Synchronization from OID to AD failed by using ActiveExport profile
Hi All
Synchronization from OID to AD failed by using ActiveExport profile
and i use copy activeexp.map.master that contains
DomainRules
cn=Users,dc=software,dc=raya,dc=corp:CN=Users,DC=twa,DC=com:
AttributeRules
# Organizational Unit Mapping
ou: : :organizationalunit:ou: : organizationalunit
# Container mapping
cn: : :orclcontainer: cn: :Container
#Domain cannot be exported
#name: : :domain: dc: :domain
cn:1: :inetorgperson:cn: :User
cn:1: :inetorgperson:SAMAccountName: :User
# attribute rule for mapping Active Directory LOGIN id
#mail: : :person:sn: :User:
mail: : :person:UserPrincipalName: :User:
# attribute rule for mapping entry and to create orclUserV2
# There should be a mapping rule with orcluserv2 objectclass
# without which the PORTAL may not function properly
cn: : :inetorgperson:givenname: :person
givenName: : :person:displayName: :person
# mail needs to be assigned valid value for default settings ing DAS
mail: : :inetorgperson:mail: :person
# The next mapping rule is for synchronizing password from OID to AD.
# Additional configuration is required. Please refer to DIP documentation
# for details.
# NOTE - To synchronize password from OID to AD, uncomment the next rule.
# userpassword: : :person:unicodepwd: :person:
# Setting useraccountcontrol to "544" (0x220) means
# 1) regular account 2) password not required 3) user account is enabled
cn: : :person:useraccountcontrol: :person:"544"
mobile: : :inetorgperson:mobile: :organizationalperson:
# GROUP ENTRY MAPPING RULES
cn: : :orclgroup:cn: :group:
# This will work successfully only when cn doesn't have any
# special characters associated with it.
cn: : :orclgroup:SAMAccountName: :group:
uniquemember: : :groupofuniquenames:member: :group:
when i check the log file i found
Trace Log Started at Mon Jul 24 07:54:58 EEST 2006
tampro.Twa.com:389
rdn value is missing in change record when performing insert operation. Please ensure that required mapping rule is specified in the profile.
java.lang.NullPointerException
at oracle.ldap.odip.gsi.ActiveWriter.insert(ActiveWriter.java:286)
at oracle.ldap.odip.gsi.LDAPWriter.writeChanges(LDAPWriter.java:272)
at oracle.ldap.odip.engine.AgentThread.mapExecute(AgentThread.java:581)
at oracle.ldap.odip.engine.AgentThread.execMapping(AgentThread.java:306)
at oracle.ldap.odip.engine.AgentThread.run(AgentThread.java:200)
null
ActiveExport:Error in Mapping Enginejava.lang.NullPointerException
java.lang.NullPointerException
at java.io.Writer.write(Writer.java:126)
at java.io.PrintStream.write(PrintStream.java:303)
at java.io.PrintStream.print(PrintStream.java:462)
at java.io.PrintStream.println(PrintStream.java:599)
at java.lang.Throwable.printStackTrace(Throwable.java:461)
at oracle.ldap.odip.engine.ODIException.printStackTrace(ODIException.java:296)
at oracle.ldap.odip.engine.AgentThread.mapExecute(AgentThread.java:740)
at oracle.ldap.odip.engine.AgentThread.execMapping(AgentThread.java:306)
at oracle.ldap.odip.engine.AgentThread.run(AgentThread.java:200)
Updated Attributes
orclodipLastExecutionTime: 20060724075501
orclLastAppliedChangeNumber: 3833
orclOdipSynchronizationStatus: Mapping Failure, Agent Execution Not Attempted
orclOdipSynchronizationErrors: Unknown Error Encountered
Sleeping for 1 secs
can any one tell me what can i do ?If its a very rare failure, then as you mentioned, you can skip it..
-
Server error: "The attempt to read data from the server '(null)' failed"
Multiple times during each day my client (Mail.app) puts up a little exclamation mark "!" next to the mail account hosted on our Leopard Server. Clicking on this little alert icon pops up a message that reads:
+There may be a problem with the mail server or network. Verify the settings for account “Leopard Server Account” or try again.+
+The server returned the error: The attempt to read data from the server “(null)” failed.+
I can make the "!" go away by choosing Mailbox>Synchronize>Leopard Server Account. And everything seems peachy but it inevitably pops up again in another hour or two. It's annoying because I'm not sure if mail is getting through or not when the "!" is up.
Any ideas why this is happening?MY SOLUTION REPOSTED FROM ANOTHER THREAD:
I've just solved a similar issue.
I have a dedicated server running Plesk 9.5 and when I upgraded to iLife 11 and Snow Leopard this error appeared. I could quickly click "get mail" and I'd get all my mail, but only 3-4 of my 9 mail accounts would connect. Theo others would have the error:
"The server error encountered was: The attempt to read data from the server..."
I found solutions for those using IMAP mail:
modify the /etc/courier-imap/imapd configuration file and change MAXDAEMONS from 40 to 80 and MAXPERIP from 4 to 40. This allows all the machines behind my home firewall to connect to multiple accounts on the e-mail server with mailbox caching enabled.
I'd made this change on my server but it didn't seem to have any effect. It dawned on me that I'm using POP, not IMAP. So I found in /etc/courier-imap/pop3d the same settings. I changed the MAXDAEMONS from 40 to 80 and MAXPERIP from 4 to 40 and voila, all my connections concurrently worked.
This has taken me more than two days to fix and I hope posting this helps someone else with the same issue. -
How to disable manual time on Aironet 1231
I have a Aironet 1231 with IOS 12.3(8)JEB1. I have enabled SNTP, but it still shows the time and date that are configured manually. How do you disable the manual time setting?
Once you are syncronized with your time server the manual field is filled with the current date and time. check under the time server address for the word Syncronized if you don't see it your AP has not been able to reach the time server.
also be sure to check the Event log configuration and select the time format. you will probably want to select local for the time stamp display.
good luck
Bill -
Hi,
I am connecting the RV180 to a Huawei Echolife HG850a ONT via PPPoE, dynamic IP address from ISP.
However, error message shows:
Fri Apr 19 02:54:15 2013(UTC) [rv180][System][NONE] pppoeMultipleEnableDisable: pppoe enable failed
Fri Apr 19 02:55:16 2013(UTC) [rv180][System][NONE] pppoeMultipleEnableDisable: pppoe enable failed
I am not able to get the RV180 to logon via PPPoE and get its dynamic IP.
Firmware is version 1.0.2.6,
tried resetting to factory defaults, still the same.
thanks.Let me explain a bit more about my case here.
My ISP is Telekom Malaysia and Service is Unifi - Fiber-To-The-Home (FTTH).
The service is "terminated" by a Huawei HG850A Optical Network Terminator (ONT).
The ONT then needs to be connected to a 802.1Q VLAN capable PPPoE router to split VLAN ports 500 and 600. 500 for Internet stream and 600 for IPTV stream.
Our ISP provides us with a dlink DIR-615 router that will work fine with the above setup.
But that Dlink DIR615 is not enough as I would like to connect to other site offices with cisco VPN, namely using Cisco RV042, RV082.
So I need to know what is wrong with the RV180 or is it a problem with my configuration.
Other people from malaysia have been configuring their other routers with no problem as below:
http://klseet.com/index.php/tl-wr1043nd-ver18/setup-for-unifi-10031-rc6
http://klseet.com/index.php/setup-walk-through/setup-for-unifi
thank you -
% waas enable failed: WAAS memory requirements not met
Dear Team,
We have upgraded our WAAS devices to 5.0.1 and upgraded the brach router that having waas express license to 15.2 3 T. Now we are getting following error while we are enabling the waas from WAN interface.
% waas enable failed: WAAS memory requirements not met.
before upgrading the branch router itsWAAS working fine and we are facing this issue after upgrading the router from 15.1 to 15.2.
Branch router Model: 1941.
Kindly suggest why we are getting these error while we are enabling the WAAS in Wan interface.
Please find the below mentioned show version output from branch router.
BRouter#sh ver
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 23-Mar-12 15:35 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M12, RELEASE SOFTWARE (fc1)
HB2503R0 uptime is 4 hours, 50 minutes
System returned to ROM by reload at 17:25:07 IST Sat Sep 22 2012
System restarted at 17:26:42 IST Sat Sep 22 2012
System image file is "flash:c1900-universalk9-mz.SPA.152-3.T.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
Cisco CISCO1941/K9 (revision 1.0) with 2269152K/90112K bytes of memory.
Processor board ID FGL1549221B
2 Gigabit Ethernet interfaces
2 Serial(sync/async) interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
1 cisco Embedded service engine(s)
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO1941/K9 FGL1549221B
Technology Package License Information for Module:'c1900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
data None None None
Configuration register is 0x2102
Brouter#
Brouter#sh flash
-#- --length-- -----date/time------ path
1 55398712 Nov 29 2011 20:37:04 +05:30 c1900-universalk9-mz.SPA.151-4.M2.bin
2 2903 Nov 29 2011 20:58:52 +05:30 cpconfig-19xx.cfg
3 3000320 Nov 29 2011 20:59:06 +05:30 cpexpress.tar
4 1038 Nov 29 2011 20:59:16 +05:30 home.shtml
5 122880 Nov 29 2011 20:59:24 +05:30 home.tar
6 1697952 Nov 29 2011 20:59:38 +05:30 securedesktop-ios-3.1.1.45-k9.pkg
7 415956 Nov 29 2011 20:59:52 +05:30 sslclient-win-1.1.4.176.pkg
8 66415436 Sep 22 2012 17:24:06 +05:30 c1900-universalk9-mz.SPA.152-3.T.bin
129417216 bytes available (127070208 bytes used)
Brouter#sh hardware
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTW
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 23-Mar-12 15:35 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M12, RELEASE SOFTWARE (fc1)
Brouter uptime is 4 hours, 51 minutes
System returned to ROM by reload at 17:25:07 IST Sat Sep 22 2012
System restarted at 17:26:42 IST Sat Sep 22 2012
System image file is "flash:c1900-universalk9-mz.SPA.152-3.T.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
Cisco CISCO1941/K9 (revision 1.0) with 2269152K/90112K bytes of memory.
Processor board ID FGL1549221B
2 Gigabit Ethernet interfaces
2 Serial(sync/async) interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
1 cisco Embedded service engine(s)
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
We are geeting the "SSL hand shake failed while communicating with WAAS express device " critical warning from Central manger GUI for the same branch express. Kindly suggest how we can resplve this issue.
Thamks in Advance.
Regards.
RanjithHi Ranjith,
Can you try the following commands on your router and see if it helps:
configmemory-size iomem 5
If it doesn't and that you are sure you have enough memory on your router to support WAAS Express, I would advise you to open a TAC case to have this investigated in depth.
Regards,
Nicolas -
Installation of the Proof of Purchase from the ACPI table failed. Error code:0xC004F059
I just updated Window 8.0 to 8.1 for the second time as the first Time there was an UEFI issue... the 8.1 installs and update seemed smooth... I shut down, and I leave for work. I come home fire up my PC it seems slow!! it boots...
I notice some live tiles are active I prefer mine off so I shut off a couple Live tiles. so then I decide to open the Mail tile and it locks up... and then one of my browsers freezes up!!! I could not open task manager at all to end the
proses, so I decided to restart and then an app was not allowing windows to restart!!! so windows ended the task on its own could not make out what program or app it was!!! and the machine booted up slower again. I went into the event viewer
and what do I find in there is this stuff and now looking at it this all started after the windows 8.1 update... I get it we all want the latest and greatest OS but as my mom said good things come to those whom wait don't rush into anything!!!
and I think Microsoft you are rushing to push stuff out onto the Market... so now I have to sit here and wonder why my PC now takes 2 + minutes to load!!! (BS) and on win 8.0 it took 60 seconds... fix this please I will watch and see if
this happens again if it keeps up I will have to once again revert back to 8.0 and at that point I will want some $$$ compensation for my loss... why should I have to go through hoops for something with the word Mircrosoft attached to it...
I wonder how many others have had this same issue and don't even know its happening....
1.
Installation of the Proof of Purchase from the ACPI table failed. Error code:0xC004F059
2.
taskhostex (2888) WebCacheLocal: The shadow header page of file C:\Users\Dale\AppData\Local\Microsoft\Windows\WebCache\V01.chk was damaged.The primary header page (4096 bytes) was used instead.
3.
The driver \Driver\WudfRd failed to load for the device SWD\WPDBUSENUM\{362b48de-4382-11e3-be6e-3085a9a945d8}#0000000000007E00.
4.
Driver detected an internal error in its data structures for
5.
The program wwahost.exe version 6.3.9600.16431 stopped interacting with Windows and was closed. To see if more information about the problem is available, check the problem history in the Action Center control panel.
Process ID: e14
Start Time: 01cf3eb70280ca6e
Termination Time: 4294967295
Application Path: C:\WINDOWS\syswow64\wwahost.exe
Report Id: f7b4be2f-aaaa-11e3-8250-3085a9a945d8
Faulting package full name: Microsoft.SkypeApp_2.0.0.5011_x86__kzf8qxf38zg5c
Faulting package-relative application ID: App
6.
The program wwahost.exe version 6.3.9600.16431 stopped interacting with Windows and was closed. To see if more information about the problem is available, check the problem history in the Action Center control panel.
Process ID: 15bc
Start Time: 01cf3eb66f89a193
Termination Time: 15
Application Path: C:\WINDOWS\system32\wwahost.exe
Report Id: 0fd54265-aaaa-11e3-8250-3085a9a945d8
Faulting package full name: microsoft.windowscommunicationsapps_17.4.9600.16384_x64__8wekyb3d8bbwe
Faulting package-relative application ID: Microsoft.WindowsLive.MailI have the something similar happening as reported in event viewer in the warning section:
System
- Provider
[ Name] Microsoft-Windows-Security-SPP
[ Guid] {E23B33B0-C8C9-472C-A5F9-F2BDFEA0F156}
[ EventSourceName] Software Protection Platform Service
- EventID 1058
[ Qualifiers] 32768
Version 0
Level 3
Task 0
Opcode 0
Keywords 0x80000000000000
- TimeCreated
[ SystemTime] 2014-08-13T04:35:49.000000000Z
EventRecordID 80761
Correlation
- Execution
[ ProcessID] 0
[ ThreadID] 0
Channel Application
Computer Monzworks
Security
- EventData
0xC004F059
installation of the proof of purchase from the acpi table failed 0xc004f059
My System Properties page says "Windows is activated" and a product Id is displayed. I am on a window 8.1 core OS after applying the update successfulling from Window 8. My computer is an AsusTek Computer Inc. ,
Asus Desktop PC CM1745 Series - 64-bit Operating System x64-based processor.
I had trouble with AODDriver4.2.0 causing errors because the system could not find the path, It turned out to be uncleared program remnants in the registry were looking for an old version of the driver, in the wrong place , instead of the current one.
Oh, and I tried sfc/scannow and DISM /Online /Cleanup-Image /RestoreHealth from elevated cmd prompt and elevated powershell ise everthing was reported with no errors and with powershell, the report said windows store corruption was repaired.
Before this I had used apps.diagcab and it said my IE 11's temporary internet files folder was in the wrong place that it was going to put it back. Well, it messed up my IE 11 so the folder location was in the same place but it was not listed in the
location: . <----- Just like this. Plus the amount of disk space available was 8mb-which messed up any sort of operations for example putting in a new search
engine could not be completed. I had to use a system restore. I currently have no errors showing up but warnings yes. thankfully most are minor.This is the other event viewer report which could be related:
- System
- Provider
[ Name] Microsoft-Windows-Security-Auditing
[ Guid] {54849625-5478-4994-A5BA-3E3B0328C30D}
EventID 5061
Version 0
Level 0
Task 12290
Opcode 0
Keywords 0x8010000000000000
- TimeCreated
[ SystemTime] 2014-08-13T03:48:26.671362500Z
EventRecordID 290021
Correlation
- Execution
[ ProcessID] 676
[ ThreadID] 728
Channel Security
Computer Monzworks
Security
- EventData
SubjectUserSid S-1-5-21-4255092528-2166032690-2543152005-1002
SubjectUserName Monz Prez
SubjectDomainName MONZWORKS
SubjectLogonId 0x239d9
ProviderName Microsoft Software Key Storage Provider
AlgorithmName UNKNOWN
KeyName CD1CC265-0DA0-4230-8419-CB6F808FE688
KeyType %%2500
Operation %%2480
ReturnCode 0x80090016
I am tired so talk among yourselves.
Sincerely Tired -
Back up from computer and icloud failed...
My ipad 2's home button was not responding properly. I was adviced to restore the device by the retailed seller. I backed up the device to both icloud and computer. I've been using icloud for a long time. Later, I hard reseted the device reloaded it from the computer; however, pages, keynotes and numbers files are not loaded properly. The folders and file names are there but the files are missing. By the way icloud synchronization has stopped due to some unidentified error. Please HELP!!! I can not recover my works.
Thanks, this is what I thought!
I understand that iCloud doesn't back up apps though? Is this correct or does it back up the same content as iTunes?
The other issue I was having with restoring from iCloud (which I initially tried to do before restoring from iTunes) was that the restore would commence and a few minutes from the end it would disconnect from the Wifi and fail. I did this a few times and it kept failing. I don't think this is my wifi as it works perfectly fine for my Mac and iPad during this time... -
hii,,, i am using iphone 3g, i am trying to install apps from apple store,, installation stop in middle,and say,, u have to do install through itunes from your laptop. when i am trying to install it from my laptop,, its failed again n again,, help me out ,
Many thanks.
With those symptoms, I'd try the following document:
Apple software on Windows: May see performance issues and blank iTunes Store
(If there's a SpeedBit LSP showing up in Autoruns, it's usually best to just uninstall your SpeedBit Video Accelerator.) -
Hello,
I have create a an external content type .
I Choose "Connect with user's Identity".
I create a external list that uses the ExternalContentType.
When I try open the external list from browser by User "TestUser" . I get the following error "Message from External System : 'Login failed for user 'NT AUTHORITY\IUSR'.'"
My Question :
I need to know why pass the credential "NT AUTHORITY\IUSR" to connect to the data base not the
current log in"TestUser" ? How Can I solve it ?
Thanks
Hema
ASkHi,
did you configure Kerberos delegation?
NTLM fails when you try to open external list from client computer, because SharePoint cannot pass user's identity - "Double Hop" issue.
Take a look at confguring Kerberos for SharePoint 2010 white paper
Download Configuring Kerberos Authentication for Microsoft SharePoint 2010 Products from Official Microsoft Download Center
http://www.microsoft.com/en-us/download/details.aspx?id=23176
Robi MCT Kompas Xnet d.o.o. Ljubljana | blog: http://xblogs.kompas-xnet.si | website: http://www.kompas-xnet.si
Slovenia
Please vote if you find reply useful or mark it as answer.
Thank you -
i have a 10.6.8 mac os x system in a intel processor computer. how can I addressbook contacts to icloud. I tried exporting my import my addressbook and failed, then exportind a vcard from all contacts and failed and finale only one vcadr and failed. Something might i doing wrong
I just had the same problem, I've updated to 10.6.8 yesterday, and since then the browsing are very slow, no matter what broswer I am using, the upload download speed are still the same. But browsing just take forever, It takes for example google.com 30 seconds to load. I have Extream high speed internet connection, 3 other computers, and the only one is having this problem is the Mac after the update.
Something in this update screwed my browsing capabitilties, I tried downloading Crome browser, same issue.
I hope there is a way beside TimeMachine to revert the latest update. I don't want to reformat as I am sure as soon as I am going to do the update it will cause the same problem.
Model Name: iMac
Model Identifier: iMac11,3
Processor Name: Intel Core i7
Processor Speed: 2.93 GHz
Number Of Processors: 1
Total Number Of Cores: 4
L2 Cache (per core): 256 KB
L3 Cache: 8 MB
Memory: 12 GB
Processor Interconnect Speed: 4.8 GT/s
Boot ROM Version: IM112.0057.B00 -
How can I prevent oracle from locking accounts after failed logins?
how can I prevent oracle from locking accounts after failed logins?
Thankssvarma wrote:
So what is the difference between the profile settings ...FAILED_LOGIN_ATTEMPTS and the parameter settings SEC_MAX_FAILED_LOGIN_ATTEMPTS?
Prior to 11g we only used profiles to control failed_login_attempts.. Then why we need thsi new parameter now?http://download.oracle.com/docs/cd/E11882_01/server.112/e17110/initparams221.htm#I1010274
http://download.oracle.com/docs/cd/E11882_01/server.112/e17222/changes.htm#UPGRD12504
http://download.oracle.com/docs/cd/E11882_01/server.112/e17118/statements_6010.htm#SQLRF01310
As documented ...
FAILED_LOGIN_ATTEMPTS is a property of a profile, and will lock an account
SEC_MAX_FAILED_LOGIN_ATTEMPTS is an initialization parameter and will drop a connection but says nothing about locking accounts. -
JDeveloper3.1.1.2 problem:convert from UTF8 to UCS2 failed
oracleTeam:
i test JDeveloper3.1.1.2,it has problem in runtime:convertion from UTF8 to UCS2 failed ,AttributeLoadException.( our language is chinese)
I found that oracle\jbo\server\QueryCollection.class in dacf.zip maybe has problem,i use this class of JDeveloper3.1 to repalce same_name class in JDeveloper3.1.1.2,above problem disappeared,
but because this class is not suit of JDeveloper3.1.1.2,other problems appeared.
so you should work out this problem ,i hope
it runs correctly.I searched this forum and the SQLJ/JDBC forum, and found a few occurrences of this problem. Among the things people suggested:
* Changing JDBC drivers (experience varied as to which one fixed the problem)
* Adding nls_charset1x.zip to your CLASSPATH
* Ensuring you're using the same character set on the client and server.
I suggest you take a look at the following discussion threads: http://technet.oracle.com:89/ubb/Forum8/HTML/001810.html http://technet.oracle.com:89/ubb/Forum8/HTML/000065.html http://technet.oracle.com:89/ubb/Forum2/HTML/000820.html
Blaise
null
Maybe you are looking for
-
ITunes 10.1.0.56 Distorts Computer Sounds When I Connect My iPhone 4
I have an ASUS Notebook. Attached to a USB port is an M-Audio Fast Track Pro, which I use as an external Sound Card, and which is connected to external speakers. When I hook up my iPhone 4 to iTunes, all sound is distorted out of my speakers, and I h
-
What is better than Skype when two iPad users want to live chat?
What is better than Skype when two iPad users want to live chat?
-
BT File Transfer: Files with "&"s cause reception failure
Hi, I'm using a Satellite A200 with the latest BT Stack (5.10.06T). File transfer is fine, unless the file has an ampersand (&) in it... Is this a known bug? Is there a fix due? It's incredibly annoying! Cheers, Greg
-
Weird Finder behaviour - I think.
I seem to be having a recurring problem lately that I haven't been able to duplicate. I'll be working in an application (and sorry... I can't be specific - yet) and when I click on the Dock to switch to a different (open) application, a finder window
-
I've upgraded from PE7 to PE11 and the new one is a lot more complicated but sadly the online help is not very helpful. I think I can puzzle most of it out but my biggest issue is that the timeline display is now full of dozens of tiny clips and I ca