RAM problems with KT3 Ultra 2 causing STOP errors in XP

I've run the NEC ncramtst program on my PC and its coming up with an error in the extended memory at adddress 1B8EE01C which probably explains the stop errors and problems I've been having in XP...
I've tried reseating the RAM and tried a different slot but it still returns the same error.
The PC is only 2 months old and I have only experienced stop errors in the last 2 weeks or so and usually are at random - and occur more often when copying files - or putting load on the PC.. any ideas why the RAM is only now causing errors and what the problem is?
Are the problems definatly being caused by RAM or could it be the motherboard?
Thanks in advance
Ben
MSI KT3 Ultra 2
AMD AlthonXP 2400+
512Mb PC2700 DDR RAM (with errors)
80Gb Hard drive
Geforce Ti4400 Graphics card
Modem
LAN

OK I found a few minidumps in the event log
The computer has rebooted from a bugcheck. The bugcheck was: 0x10000050 (0xde1d3ee0, 0x00000000, 0x804eef61, 0x00000000)
Error code 10000050, parameter1 e262ca7a, parameter2 00000001, parameter3 8053cb3e, parameter4 00000001.
Error code 1000008e, parameter1 c0000005, parameter2 8053cbb1, parameter3 ee5b1a40, parameter4 00000000.
The computer has rebooted from a bugcheck. The bugcheck was: 0x10000050 (0xe1fe9a18, 0x00000000, 0x8053cbb1, 0x00000001). A dump was saved in: C:WINDOWSMinidumpMini030703-10.dmp.
Hope these help

Similar Messages

Ram Problem With KT3 Ultra

Hi Guys,
I have posted on here before.
I have a kt3 ultra mobo.
The problem i have is when playing games the system locks up and i have to hard restart.
I have followed advice from this board the the faq ant mobo bios set up which sadly has not solved the problem.
Very strange but in the pc i have two x 256 meg ddr ram.
If i take either stick out the pc plays games perfectly. This is frustrating as both sticks work fine on their own but not together.
ANY IDEAS ? ;(

Hi,
Sometimes it happens that sticks just won't work together....
You might want to swap one of the sticks with a friend to see if the problem is gone...

Sound problems with KT3 ultra

Hello All
I have a KT3 Ultra, WinXP Pro, LG CD-RW (HL-DT-ST CD-RW GCE-8160B ), 512 Mb DDR Ram etc.
My problem is that when i rip cd's to MP3 i lose all sound. This has happened with Easy CD-DA and Exact Audio Copy.
If I go into AC'97 Audio config all speakers seem to work exept the Front Left and Right. But this seems to stop them all from playing any audio.
Reinstalling AC'97 fixes it but it's a bit annoying.
Audio driver : 5.10.0.3840
Audio controller : VIA 3059
AC97 Codec : ALC650
Any help appreciated
upinsmoke

I think i solved it by installing the 5.10.0.4050 drivers.
upinsmoke
cant seem to change the thread description to SOLVED

Problems with kt3 ultra + radeon 9800pro

hey guys,
heres my story (bare with me)
i bought a radeon 9700 pro around christmas time, recieved it, (almost) everything worked fine on it, etc etc. however in games, it would give me this weird flickering poly thing going on (screenshot included) after seeing this, i stuck an extra fan in my case, thinking it was a heating issue. no worky. after that i just assumed the heatsink/fan wasnt securely on the chip. whatever.
anyway, i returned the vid card, got my money back and just decided to sit on the extra money for another couple of months and let prices drop a bit.
soooo i order myself a radeon 9800 pro this week. i get it today, and im getting the EXACT SAME PROBLEM. so obviously it wasnt a heat issue, it was.. something else.
this is where you come in anyone have ANY ideas why i would be having this problem? im attaching a screenshot i snagged of what the error looks like (if that will help at all)
i have already tried running driver cleaners, blah blah blah. i even reformatted and reinstalled windows on the drive, and im STILL having the same problem. not to mention i get occasional lockups and bluescreens.
ive tried flashing bios, updating mobo drivers nothing fixes it.
is this just some quirky incompatability between the mobo and the vid card or what? (i had a gf3ti200 in here before the 9800pro.. never had any problems)
so can anyone help or am i just going to have to buy a new motherboard?
msi kt3 ultra
512 pc2700 ram
80 gig wd
ati radeon 9800 pro

"DOS'ish" ?
start with flashing the latest mobo bios before you start if you haven't allready. I recommend stick with the 3.7 Cat driver (many people are reporting worse problems with the later rev Cat drivers) and follow these directions:
1) download and install the latest via driver (i know, you have it)
2) download and install latest soundblaster driver (if you are using a soundblaster audio card of course)
3) download and install catalyst 3.7 driver/control panel/samartgart from ati.
4) disable fast-write in bios (this was causing corrupted icons and cursor in windoze).
5) go to c:\programs\ati technology\ati control panel and execute smartgart (it's a link)
6) enable - pci read/write and agp read (probably allready is enabled).
7) disable - agp write (default in my case was on causing lots of stability problems in games).
"apply", reboot, then "ok".
above solved all my probs w/9600 pro and msi kt3 ultra-aru
good luck!

Problems with KT3 Ultra (MS-6380E)..please help

Hey all-
Here is my system configuration:
MSI KT3 Ultra MS-6380E) motherboard
AMD Athlon 2100+ XP cpu
(2) 512mb PC2700 DDR ram (1 gig total)
(2) 120gb Western Digital 7200rpm Harddrives (240gb total)
Nvidia Geforce Ti 4600 video card
Creative Labs Sound blaster Audigy Platinum
LG 32x10x40 CDRW
16x DVD ROM
400 watt power supply
Here is my problem:
Just built the machine, checked every plug and everything and when I turn on the machine I got no screen, no post, no beeps, nothing.
So I turned the machine, and cleared the CMOS. Turned the machine back on and got post , went into the BIOS, set the time,date, yada yada, all the drives were detected fine. I went in the Frequency/Voltage Control screen and the "CPU FSB Clock" was set to 100 mhz, "CPU Ratio" was set to Auto as was the "CPU Voltage, DDR Voltage, and AGP Voltage". I saved settings and rebooted but then I didn't get a screen, no post, no beeps.
I tried clearing CMOS again, turned machine on, got back in the BIOS just fine. I tried setting the CPU FSB Clock to 133mhz and left everything else on Auto. Rebooted and once again ..nothing.. no screen.
I don't understand what the problem could be. It seems that I can only get a screen when I clear the CMOS. But even if i use the "Load BIOS Setup Defaults" or even the "Load High Performance Defaults" I still get no screen or anything when I reboot.
Can anyone help me here? I have never run into this before.
Thanks in advance!!
Joe

If it is only doing it when you turn your bus speed of 100 up to 133 for the xp processor then I have had the problem. If you are booting with a bad cpu that isn't working properly (can't run at 133) then the computer will not POST. As soon as you clear the cmos it sets the speed back down to 100 for failsafe. If you try to boot a duron processor like a 700 or something on fsb 133 then the motherboard won't post. Make sure you don't have a duron processor instead of a athlon xp or a bad cpu. I would recommend taking it to the place you bought it or else an autorized amd spot. They should be able to throw in another proc and check it out.

Problem with KT3 Ultra/AMD 2100+ temp

hi,
Im not too familiar with motherboards but i know when there is something seriously wrong. I have a MSI KT3 Ultra motherboard with a AMD XP 2100+ processor. My computer normally ran at a CPU temp of 45C, but today I installed the new version of PC Alert 4. All of a sudden my CPU temp increased 15C. Now its running at 60C, which i think is too high. I havent changed anything else, and nothing has been overclocked. I have a Geforce 4 Ti 4400 and 512mb RAM. Please help.
Thanks in advance

Quote
PS: anyone else have any other ideas? dont wanna be ungrateful but i dont think thermal paste stops working within a 2 hour period all of a sudden.
No it wont, but it has probably been running at that temp all along.....Maybe your first PCAlert was just giving false temps........Did you ever check it in the bios before?

What RAM works with KT3 Ultra (Orig) ????

Hey there,
SORRY BIGDADDY. Come to find out a new board
did not fix the prob I am having probs with the OS. Not
only that but several other programs don't work
like burning software, drivers, and the new DX won't
even install right. I figured NEW CPU...but as you can
see I need NEW RAM. So instead of buying PC133 for
almost the same price I figure get some DDR 2100 for
about $10-20 more and the KT3 is $10 more. Do the
math here and I could substantially increase my comp
considerably. :D
Foreveryone out there I need to know what ram works
with the KT3 Ultra. I know this board is very picking
about ram since the AMI bios is the issue.
I am looking at these:
1) Kingston PC2100
2) Crucial PC2100
3) Micron PC2100
Thanks in advance for any replies
SladeZero980
I also got a XP 1600 + for $66 from NEWEGG

OK I found a few minidumps in the event log
The computer has rebooted from a bugcheck. The bugcheck was: 0x10000050 (0xde1d3ee0, 0x00000000, 0x804eef61, 0x00000000)
Error code 10000050, parameter1 e262ca7a, parameter2 00000001, parameter3 8053cb3e, parameter4 00000001.
Error code 1000008e, parameter1 c0000005, parameter2 8053cbb1, parameter3 ee5b1a40, parameter4 00000000.
The computer has rebooted from a bugcheck. The bugcheck was: 0x10000050 (0xe1fe9a18, 0x00000000, 0x8053cbb1, 0x00000001). A dump was saved in: C:WINDOWSMinidumpMini030703-10.dmp.
Hope these help

Big problem with KT3 Ultra (ms-6380e v1.0) after flashing the BIOS (de

Hello out there.
I have a real complicated matter with my Kt3 Ultra board.
Used to work fine, but after I flashed it with the latest BIOS (5.7), the board has this strange behaviour: when I clear the CMOS, the board boots up, when I change & save the settings, the board does not "come to life"(black screen & beeper silent).
It has also this weird problem: it shows garbage charaters on the voltage setting of the CPU. Instead of voltages (i.e. 1.750 etc. etc.) I have only "scrambled" strings.
I had MANY difficulties in upgrading the BIOS because the AMI-flashing utility kept telling me "bios protection enabled) (but there was NO bios-protect setting in the previous bios - I checked a zillion times)...but after trying with different revisions finally I made it.
I already tried everything (re-flashed older bios-es etc. etc.)and I'm starting to feel beat ... if you have any advice, please le me know.
It would be really SAD to put this great board in the garbage-dump....
Bye,
Wyk'03

im having problems with this board as well,
i had no problems with the flash,
i did this...
boot to win me floppy,
copy the flash files to ramdrive, flashed to latest bios..
now windows hangs when i have my ac97 audio enabled in bios...
I WANT MY AC97!
hmmm can you get to a dos prompt from a boot disk?
try re-flashing with 1.0 again and then disable the cmos virus protection thingy, and yes it was there it was in the 1.0 bios on the main screen.

Problem with Kt3 ultra

Ok here is my problem. I reformatted my computer and accidentally f-ed with my bios settings. After clearing the cmos and flashing the bios, i reformatted again and reinstalled windows xp. I was able to update everything (SP1, audio drivers) except the video driver. I can install the video driver, but when i reset to finish the installation, the system goes to the windows load screen and then the monitor just goes blank. When i go into safe mode, there is a message that my video card had problem drawing something. I have tried every possible driver there is, and its is the same result. Anyone got suggestions? I have AMD 1700, kt3 ultra, mx440 nvidia. Thanks

OK i tried it in safe mode, which didnt work. Maybe i'm doing this wrong. Here is my procedure. The last working config was right before the video card is detected. I let windows detect the card and install the driver. Then i go into add remove programs and remove the nvidia drivers, which removes the video card from the device list. I then install the 4 in 1 drivers. Restart. Then install the video driver. The restart again, which always leads me to dark screen after windows load. By the way, tahnks for your help.

Odd video problem with KT3 Ultra 2-r and GeForce4Ti4400

I don't know if I should post this on the VIA forum or on the VGA forum, so I'm gonna post on both. sorry.
My system specs are on my signature, and anyways, here's my problem.
When I turn on my PC, the monitor shows jaggy white lines all over the screen (as if the refresh rate / resolution was too high) instead of showing the GeForce BIOS (right before the POST).
This is weird, since a year ago, when I got my MSI nForce/ MSI GeForce4 Ti4400, this wasn't a problem. And now I have KT3 Ultra 2 and MSI GeForce4 Ti4400 Chapmionship edition, and I do.
Not only that, but most of the times when I restart my PC, my monitor goes into POWER SAVING mode instead of showing the POST and Loading Windows screen.
I even try to go into the BIOS while the monitor is in powersave mode and it does go in, but the monitor is dead.
The monitor comes back to life as soon as it reaches the WindowsXP logon screen. But like I said, it goes into powersave mode as soon as I restart and until it reaches the WinXP logon screen.
I mean, this is a minor problem, but its a pain in the ass!!!!
Whenever I'm trying to tweak the BIOS, it will often times do this, and even if I turn the monitor off, unplug it from the PC, unplug it off the wall, when I plug it back in, it still is in powersaving mode, even though the PC is running.
HELP!

No, my Ti4400 is not the Champ ed. The actual model number on it is 8871 ver-1.00. You can read about my problem's in the "Have you seen this?....." thread on this forum (page 7 now I think)
I haven't had a problem in the last couple days though. I removed some Reg tweaks (this is a DAW box) and ....dont luagh, turned up the heat in my house. I'm not sure if it was the Reg edit or Temp, but things are working ATM.
Nice to know I'm not alone though,
C

Audio Problems with KT3-Ultra MB

I have the KT3-Ultra MB and I am trying to set up a four speaker setup using the sound manager utility that came packaged with the board. Regardless to which setup I select from the utility which configures the 3 onboard sound jacks, I cannot get any sound from the second (rear) port. Has anyone else encountered this issue or know how to fix it?

I own 2 sets of speakers. One is a set with 2 satellites and a sub that (The slender black satellites from Altec Lansing I think) and I have another set consisting just of 2 satellites also from Altec Lansing. Both sets terminate in a simple headphone type jack. Either set works when plugged in to the first audio port labelled for front audio, but neither of them works when plugged into the jack configured for rear sound.
To test them I am using the Sound Manager utility that is packaged wit6h the MB that shows a picture of your setup and allows you to click on each speaker and it sends a sound to the speakers individually, allowing you to hear which ones work and whatnot. I have tried uninstalling and reinstalling the sound and I have downloaded all of the latest drivers from this website...
This thing is starting to get frustrating....

[VIA] Problem with kt3 ultra 2 and 2800+ Barton

Please help. I've a 2800+ barton on my motherboard 6380E with bios 5.7 But my processor is recignized as a 2500+.
In the bios, my Fsb is 166 and all the rest is on auto. I've 1,5 GB memory pc2700 333 mhz.
I'm trying to force 12.5/13 in bios but it stay as 11.5 (saw with cpuz). What can i do to have the 2800+ recognized with this motherboard ? Help !!! I've change the FSB to 180, but with cpu-z, the processor is still a 2500+

You could try WCPUID, which can also determine the cpu that you have.
http://hp.vector.co.jp/authors/VA002374/src/download.html
Failing that as Wonkanoby said check the codes on the cpu itself.
Perhaps as an alternative just try raising the FSB from 166 to 167. Upon boot instead of the bios detecting the cpu, it will give you the clock speed albeit at 167. Since you have the multiplier you can then work out the clock speed at 166, if you see what I mean and determine (or have a better idea) of the cpu that you have.
Good Luck

I have a problem with my viber.It has stopped working.I tried reinstalliing it again .On the setup option after entering my phone number and continuing ..it either exists or gives no service message .

I have a problem with my viber.It has stopped working.I tried reinstalling it again .On the setup option after entering my phone number and continuing ..it either exists or gives no service message .My other applications are working fine ..other applications that require internet too are working fine.

Please get in touch with Viber's customer support.

Remote Resources: "A problem with the system proxy caused the connection to fail: End of file"

Hi, I am trying to use "Remote Resources" on the current version of the Microsoft Remote Desktop for Android app, I can input the webfeed and it even shows the apps that I have configured on the server for "Remote App", sadly whenever
I try to load any of the RemoteApps, I receive an error stating " A problem with the system proxy caused the connection to fail. End of File".
I don't know what I can do to fix this, I've tried many things to no avail, also, normal Remote Desktop connections from the Microsoft Android app work flawlessly to the server.
The relevant log is the following:
[2014-Jan-09 04:40:54] RDP (0): ----- BEGIN ACTIVE CONNECTION -----
[2014-Jan-09 04:40:54] RDP (0): Final rdp configuration used: memory bookmark [
label
hostname DIAZSERVER
port 3389
loadbalanceinfo
ui.swapmousebutton false
remote.program ||ZWaveUtil
remote.workingdirectory
remote.name ZWave Adapter Utility
remote.args
rail true
soundmode 0
connect_to_console false
redirectsdcard true
performance_flags 134
arc.sessionid 0
anonymous_username
authentication_level 2
use_redirection_server_name false
username administrator
gateway [
host = DIAZSERVER
port = 443
bypass = false
connect info[
hostnames = [localhost]
gatewayHost = DIAZSERVER
gatewayPort = 443
routingToken = Cookie: mstshash=administrator
redirectionGUID =
proxyHost = 200.5.68.10
proxyPort = 8080
sessionId = -1
[2014-Jan-09 04:40:54] RDP (0): Using HttpConnect proxy at 200.5.68.10:8080
[2014-Jan-09 04:40:54] RDP (0): Using Basic Authentication with username ''
[2014-Jan-09 04:40:54] RDP (0): Protocol state changed to: ProtocolConnectingNetwork(1)
AsioEndpointContext (0): startup(): starting up down context
[2014-Jan-09 04:40:54] RDP (0): Resolved '200.5.68.10' to '200.5.68.10' using NameResolveMethod_DNS(1)
[2014-Jan-09 04:40:54] RDP (0): Resolved '200.5.68.10' to '200.5.68.10' using NameResolveMethod_DNS(1)
ASIOSocketAdapter (9): readSomething error. message: End of file. instance: 0x5d39d5c0
RpcOverHttp (9): Stream error in endpoint 0x5abbc170 : A problem with the system proxy caused the connection to fail: End of file
[2014-Jan-09 04:40:55] RDP (0): Error message: A problem with the system proxy caused the connection to fail: End of file
[2014-Jan-09 04:40:55] RDP (0): Error message: A problem with the system proxy caused the connection to fail: End of file
[2014-Jan-09 04:40:55] RDP (0): Protocol state changed to: ProtocolDisconnected(8)
ASIOSocketAdapter (9): handleRead(): exception: Exception in file '/var/lib/jenkins/jobs/rc-android-app/workspace/rdp-layer/library/jni/librdp/private/httpendpoint.cpp' at line 489
    User Message : Failed to read from channel: -1. instance: 0x5d39d5c0
[2014-Jan-09 04:40:55] RDP (0): Disconnect initiated by client
RpcOverHttp (9): Exception in endpoint 0x5abbc170 : Exception in file '/var/lib/jenkins/jobs/rc-android-app/workspace/rdp-layer/library/jni/librdp/private/httpendpoint.cpp' at line 489
    User Message : A problem with the system proxy caused the connection to fail: Failed to read from channel: -1
[2014-Jan-09 04:40:55] RDP (0): Exception caught: Exception in file '/var/lib/jenkins/jobs/rc-android-app/workspace/rdp-layer/library/jni/librdp/private/httpendpoint.cpp' at line 489
    User Message : A problem with the system proxy caused the connection to fail: Failed to read from channel: -1
[2014-Jan-09 04:40:55] RDP (0): Exception caught: Exception in file '/var/lib/jenkins/jobs/rc-android-app/workspace/rdp-layer/library/jni/librdp/private/httpendpoint.cpp' at line 489
    User Message : A problem with the system proxy caused the connection to fail: Failed to read from channel: -1
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
[2014-Jan-09 04:40:57] RDP (0): ------ END ACTIVE CONNECTION ------

My problem is that the "proxy" is the proxy set up by my 3G configuration so, I tried connecting to the remote resources through my work wifi and I get the following:
[2014-Jan-14 16:58:13] RDP (0): ----- BEGIN ACTIVE CONNECTION -----
[2014-Jan-14 16:58:13] RDP (0): Final rdp configuration used: memory bookmark [
label
hostname DIAZSERVER
port 3389
loadbalanceinfo
ui.swapmousebutton false
remote.program ||chrome
remote.workingdirectory
remote.name Google Chrome
remote.args
rail true
soundmode 0
connect_to_console false
redirectsdcard true
performance_flags 134
arc.sessionid 0
anonymous_username
authentication_level 2
use_redirection_server_name false
username Administrator
gateway [
host = DIAZSERVER
port = 443
bypass = false
connect info[
hostnames = [localhost]
gatewayHost = DIAZSERVER
gatewayPort = 443
routingToken = Cookie: mstshash=Administrator
redirectionGUID =
proxyHost =
proxyPort = 0
sessionId = -1
[2014-Jan-14 16:58:13] RDP (0): Not using any proxy
[2014-Jan-14 16:58:13] RDP (0): Protocol state changed to: ProtocolConnectingNetwork(1)
AsioEndpointContext (0): startup(): starting up down context
ASIOSocketAdapter (9): handleResolve(): boost error: Host not found. Please provide the fully-qualified name or the IP address of the host.. instance: 0x5d474090
RpcOverHttp (9): Stream error in endpoint 0x5d46b678 : Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Protocol state changed to: ProtocolDisconnected(8)
ASIOSocketAdapter (9): handleResolve(): boost error: Host not found. Please provide the fully-qualified name or the IP address of the host.. instance: 0x5d445158
RpcOverHttp (9): Stream error in endpoint 0x5d49fa30 : Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Disconnect initiated by client
[2014-Jan-14 16:58:17] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
[2014-Jan-14 16:58:17] RDP (0): ------ END ACTIVE CONNECTION ------
Now, I know the host can be resolved because: if I connect to the same host but on a full remote desktop (as opposed to just RemoteApp on it) I have no trouble either through 3G OR through my work connection.
Moreover, I also tried directly inputting the IP as opposed to the web address of my server, I get the same error, that is the Remote Resources tab is able to access the feed (because it shows the available RemoteApps) but when I click an app it says it can't
find the Host, here's the log for the connection directly to the IP address/rdweb/feed/webfeed.aspx :
[2014-Jan-14 17:09:27] RDP (0): ----- BEGIN ACTIVE CONNECTION -----
[2014-Jan-14 17:09:27] RDP (0): Final rdp configuration used: memory bookmark [
label
hostname DIAZSERVER
port 3389
loadbalanceinfo
ui.swapmousebutton false
remote.program ||chrome
remote.workingdirectory
remote.name Google Chrome
remote.args
rail true
soundmode 0
connect_to_console false
redirectsdcard true
performance_flags 134
arc.sessionid 0
anonymous_username
authentication_level 2
use_redirection_server_name false
username administrator
gateway [
host = DIAZSERVER
port = 443
bypass = false
connect info[
hostnames = [localhost]
gatewayHost = DIAZSERVER
gatewayPort = 443
routingToken = Cookie: mstshash=administrator
redirectionGUID =
proxyHost =
proxyPort = 0
sessionId = -1
[2014-Jan-14 17:09:27] RDP (0): Not using any proxy
[2014-Jan-14 17:09:27] RDP (0): Protocol state changed to: ProtocolConnectingNetwork(1)
AsioEndpointContext (0): startup(): starting up down context
ASIOSocketAdapter (9): handleResolve(): boost error: Host not found. Please provide the fully-qualified name or the IP address of the host.. instance: 0x5d372f28
RpcOverHttp (9): Stream error in endpoint 0x5dd6b168 : Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Protocol state changed to: ProtocolDisconnected(8)
ASIOSocketAdapter (9): handleResolve(): boost error: Host not found. Please provide the fully-qualified name or the IP address of the host.. instance: 0x5d378de0
RpcOverHttp (9): Stream error in endpoint 0x5e9cc1f0 : Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Disconnect initiated by client
[2014-Jan-14 17:09:31] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
[2014-Jan-14 17:09:31] RDP (0): ------ END ACTIVE CONNECTION ------
I'm really puzzled here, I've tried checking if ports where open, and ports 443 and 3389 are wide open, I don't know what else it could be.

I buyed an Ipad2 but i have a problem with the id icloud cause it's not my id !! impossible to know it, i can use it and i'm very angry

I buyed an Ipad2 but i have a problem with the id icloud cause it's not my id !! impossible to know it, i can use it and i'm very angry

With iOS 7 there’s no workaround.
They should have done this.
What to do before selling or giving away your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT5661
If the iPad was running iOS 7, iCloud: Find My iPhone Activation Lock in iOS 7
http://support.apple.com/kb/HT5818
iCloud: Activation Lock
http://support.apple.com/kb/PH13695
Find My iPhone Activation Lock: Removing a device from a previous owner’s account
http://support.apple.com/kb/ts4515
Buying or Selling a Used iPhone or iPad Running iOS 7? Read This First!
http://www.makeuseof.com/tag/buying-or-selling-a-used-iphone-running-ios-7-read- this-first/
You may have purchased a stolen iPad. Get a refund or have the prior user do this.
What to do before selling or giving away your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT5661
 Cheers, Tom

RAM problems with KT3 Ultra 2 causing STOP errors in XP

Similar Messages

Maybe you are looking for