Read dd2 in solaris 9
I have a DDS4 tape drive attached to an Ultra 1000 running Solaris 9. I need to be able to read to it in DDS2 and DDS1 format. but how do I read dds2 ??
my dds4 tape drive read and write tape dds4 ok
Thanks
Please review the following document
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=lpg50116&lang=en
Michael
Similar Messages
-
Do you have an Adobe Reader for Unix/Solaris? If so, can you provide me the URL?
The last Reader version issued for Unix is 9.5.5; you can download the appropriate files from ftp://ftp.adobe.com/pub/adobe/reader/unix/9.x/9.5.5/enu/
-
Japanese fonts for Reader on Sparc Solaris?
I am looking for Japanese fonts for Reader on Sparc Solaris.
I understand that Reader 8.1.7 is the latest for Sparc.
I searched Adobe website but only found font packages for later versions and with x86 shared objects;
I could not find font pack that is either machine independent or for sparc.
Any pointer would be greatly appreciated.
Thanks for your help.Check in ftp://ftp.adobe.com/pub/adobe/reader/unix/8.x/8.1.1/misc/
-
Slow nfs read/write from solaris 8 to solaris 10
there is a bug:4852269 which sums up my problem well.
I have a solaris 10 sparc with a big nfs shared raid5, and most of the other suns I have run solaris 8. the access time from sol8 to sol10 is awfull.
Is there some config/patch I can apply to the solaris 10 box?
I have put on the latest 10_Recommended.zipit's a ufs filesystem
If it helps, here is my /etc/default/nfs
# ident "@(#)nfs 1.10 04/09/01 SMI"
# Copyright 2004 Sun Microsystems, Inc. All rights reserved.
# Use is subject to license terms.
# Sets the maximum number of concurrent connection oriented connections.
# Default is unlimited and is obtained by not setting NFSD_MAX_CONNECTIONS.
# Equivalent to -c.
#NFSD_MAX_CONNECTIONS=
# Set connection queue length for the NFS over a connection-oriented
# transport. The default value is 32 entries.
# Equivalent to -l.
NFSD_LISTEN_BACKLOG=32
# Start NFS daemon over the specified protocol only.
# Equivalent to -p, ALL is equivalent to -a on the nfsd command line.
# Mutually exclusive with NFSD_DEVICE.
NFSD_PROTOCOL=ALL
# Start NFS daemon for the transport specified by the given device only.
# Equivalent to -t.
# Mutually exclusive with setting NFSD_PROTOCOL.
#NFSD_DEVICE=
# Maximum number of concurrent NFS requests.
# Equivalent to last numeric argument on nfsd command line.
NFSD_SERVERS=16
# Set connection queue length for lockd over a connection-oriented transport.
# Default and minimum value is 32.
LOCKD_LISTEN_BACKLOG=32
# Maximum number of concurrent lockd requests.
# Default is 20.
LOCKD_SERVERS=20
# Retransmit Timeout before lockd tries again.
# Default is 5.
LOCKD_RETRANSMIT_TIMEOUT=5
# Grace period in seconds that all clients (both NLM & NFSv4) have to
# reclaim locks after a server reboot. Also controls the NFSv4 lease
# interval.
# Overrides the deprecated setting LOCKD_GRACE_PERIOD.
# Default is 90 seconds.
GRACE_PERIOD=90
# Deprecated.
# As for GRACE_PERIOD, above.
# Default is 90 seconds.
#LOCKD_GRACE_PERIOD=90
# Sets the minimum version of the NFS protocol that will be registered
# and offered by the server. The default is 2.
#NFS_SERVER_VERSMIN=2
# Sets the maximum version of the NFS protocol that will be registered
# and offered by the server. The default is 4.
NFS_SERVER_VERSMAX=2
# Sets the minimum version of the NFS protocol that will be used by
# the NFS client. Can be overridden by the "vers=" NFS mount option.
# The default is 2.
#NFS_CLIENT_VERSMIN=2
# Sets the maximum version of the NFS protocol that will be used by
# the NFS client. Can be overridden by the "vers=" NFS mount option.
# If "vers=" is not specified for an NFS mount, this is the version
# that will be attempted first. The default is 4.
#NFS_CLIENT_VERSMAX=4
# Determines if the NFS version 4 delegation feature will be enabled
# for the server. If it is enabled, the server will attempt to
# provide delegations to the NFS version 4 client. The default is on.
#NFS_SERVER_DELEGATION=on
# Specifies to nfsmapid daemon that it is to override its default
# behavior of using the DNS domain, and that it is to use 'domain' as
# the domain to append to outbound attribute strings, and that it is to
# use 'domain' to compare against inbound attribute strings.
#NFSMAPID_DOMAIN=domain
# -
Error in reading core on Solaris 2.8 using pstack command
We are unable to read core file on Solaris 2.8 using pstack command. We are getting warning that librtld_db failed to initialize; symbols from shared libraries will not be available.
Man page of pstack says that such error can occur if a core file from one operating system release is examined on a different operating system release.
But we are trying to read the core on the same machine on which it occurred.
Does any one know what could be reason and what are the alternative to read core in such situation?Dear Gopinath,
Thanks for the response.
The problem occurred again.
In fact now it is repeatable.
We have not installed any Solaris patches after original OS installation. We have checked the core using pstack immediately after it was dumped.
We have tried reading it using dbx but it is also giving same error.
Here is the output of dbx
dbx: could not initialize rtld_db.so -- verify that corefile was generated on a compatible machine
Note: We compile our program on Solaris 2.6 as 32 bit and then install it on Solatis 2.8.
We have tried reading the core using dbx on both Solaris 2.6 as well as Solaris 2.8.
We know that this must be problem in our program (some memory violation) and has nothing to do with 2.8 or 2.6.
But inability to analyze core is happering the debugging.
Thanks
Dhananjay -
Adobe Reader on a Solaris 10 SPARC machine
Hi,
Can anyone tell me if Adobe's Vulnerability ID: APSB11-03 is applicable to Reader 8.1.7. That is the version of Reader that is installed be default with the latest version of Solaris 10 for SPARC platforms.
Thanks.Dear zata40,
No, Adobe Reader 8.1.7 for SPARC solaris is not affected by this security vulnerability, it is applicable to Win and Mac releases only.
Thanks,
Atanu Dhar
([email protected]) -
Socket read write on Solaris 8 too slow.
Hi
We have an application which consists of several server instances.
The front-end is web-based , using JSP/Servlets. We are using Tomcat 4.0.
The servlet makes several connections to the underlying servers. But the read/write operation is too slow. Same setup runs much quicker on Windows.
We are running jdk1.4.1_02 (stable ?). Would much appreciate any help.
cheers
Projyaltomcat version --3.2.3
j2sdk version----1.4
plarform---------solaris
solaris version--8
using the aboue configuration i need to deploy JSP codes on the solaris platfrom..can any technical expert guide me on how to do this..would be grateful if anyone could suggest a good site where i can download free tuorials of "JSP" for development in HTML files format or HELP format]
thank you
regards
brijesh -
Need latest acrobat reader for solaris 10 sparc version
i need latest acrobat reader for solaris 10 sparc version
checked adobe site it is only avilable for linux and not for solaris, very strangeThere's no version of Adobe Reader XI for Solaris.
The only versions you can download are legacy - see the complete list here: http://www.adobe.com/support/downloads/product.jsp?product=10&platform=Unix -
Need Adobe Reader 9.x for Solaris 10 x86
There used to be a link on your web site for the Solaris 10 x86 download for Adobe Reader 9.x products. Could you please send me an updated link or an alternative method of downloading the Solaris intel version of Adobe Reader? Would prefer the link comes directly from Adobe since verification is needed that it is from a trusted source. Thanks!
Hi,
there is no actual release of Acrobat Reader
ftp://ftp.adobe.com/pub/adobe/reader/unix/
later then Acrobat Reader 4 for Solaris x86
ftp://ftp.adobe.com/pub/adobe/acrobatreader/unix/4.x/sunx86-ar-405.tar.gz.
All posts that announce Solaris x86 support for release 8 are untrue.
The only working extended Pdf-Editor (comparable to Adobe Acrobat XI)
for Solaris x86 at the moment is PDFStudio Java
http://www.qoppa.com/pdfstudio/buy/
Best regards
Axel Arnold Bangert - Herzogenrath 2013 - Solaris 10 (x86) -
Can�t upgrade Solaris 2.6 to Solaris 9 ? HELP
Hi,
I'm trying to upgrade one Sun Enterprise 3500 with Solaris 2.6 to new Solaris 9.
I've already use SUNINSTALL and WEB START methods, without sucess.
There is no error messages in WEB START method..
When using "suninstall" method, I follow all the manual instructions with CLI mode and the instalation returns "install sucess", but when rebooting, some erros apears and starts a reboot cycle:
------ ERROR WITH SUNINSTALL ----------
Use is subject to license terms.
WARNING: add_spec: No major number for fp
WARNING: add_spec: No major number for fp
WARNING: add_spec: No major number for scsi_vhci
WARNING: add_spec: No major number for fp
WARNING: add_spec: No major number for scsi_vhci
WARNING: mod_installdrv: no major number for fcp
Cannot assemble drivers for root /sbus@2,0/SUNW,socal@d,10000/sf@0,0/ssd@w21000020372b4363,0:a
Cannot mount root on /sbus@2,0/SUNW,socal@d,10000/sf@0,0/ssd@w21000020372b4363,0:a fstype ufs
panic[cpu14]/thread=140a000: vfs_mountroot: cannot mount root
0000000001409970 genunix:vfs_mountroot+70 (0, 0, 0, 200, 14569d8, 0)
%l0-3: 000000000144a400 000000000144a400 0000000001415bc8 0000000001415bd0
%l4-7: 0000000001415800 0000000001411a80 000000000144ac00 000000000144dc00
0000000001409a20 genunix:main+98 (1409ba0, f00584cc, 1409ec0, 32a7af, 2000, 500)
%l0-3: 0000000000000001 0000000000000000 0000000001412b18 0000000078002000
%l4-7: 000000000140a000 0000000000330000 0000000001480dc8 00000000010628d0
skipping system dump - no dump device configured
rebooting...
Resetting...
Software Power ON
When using WEB START, the instalation gives some strange messages at the midle of wizard (using CLI), but continues the instalation. At the end, says "Installing Solaris Software Group", and shows a progression bar, but at same time, changes to prompt and without any error stops the installation. Some process are running but none indicates that install is in progress...
----- WITH WEB START ------ STRANGE MESSAGE:
Reading disc for Solaris Operating Environment...
The system is being initialized, please wait... \
To perform an initial install of the Solaris Operating Environment select
Initial Install. Existing contents of your hard disk will be destroyed.
To perform an upgrade of the Solaris Operating Environment select Upgrade. The
Solaris Operating Environment will be updated and other contents on the hard
disk will be left unchanged. Backing up the existing Solaris Operating
Environment is recommended.
1. Initial Install
2. Upgrade Install
Select Upgrade or Initial install [1] 2
Gathering upgrade information, please wait... \
Could not reinitialize system state. Please exit the installer and restart the
installation.
<Press ENTER to continue|
The system is being initialized, please wait../
To install basic Solaris products into their default directory locations,
select Default Install.
Custom install provides a choice of which Solaris products to install. For each
product, it also provides an option to customize the products install.
Note: Default install is not possible. Default boot disk could not be
determined.
<Press ENTER to continue>
Select the geographic regions and software localizations you want to install.
The English version of Solaris will be installed by default.
[ ] 0 Northern Africa
[ ] 1 Eastern Europe
[ ] 2 Southern Europe
------ AT THE END OF PROCESS -----
Testing the upgrade profile, please wait... /
The following items will be installed:
Solaris Operating Environment: Solaris 9 Software 4/03
Solaris Software Group: Entire Group
Backup Media Type: None
64-Bit Selection: Yes
Region and Locales:
Southern Europe
Portuguese (Portugal) ( pt_PT )
North America
English (United States) ( en_US )
English (POSIX C) ( C )
System Locale: English (United States,ISO8859-1) ( en_US.ISO8
Products:
Solaris 9 Software Supplement CD 385.
Java3D 1.2.1_04 18.3 MB
OpenGL 1.3 105.7 MB
PC launcher 1.0.2 0.9 MB
RSC 2.2.1 8.8 MB
Solaris On Sun Hardware Documentation
SunATM 5.1 9.1 MB
SunForum 3.2 27.1 MB
<--[90%]--[ENTER To Continue]--[n To Finish]-->
SunHSI PCI 3.0 0.5 MB
SunVTS 5.1 PS2 124.4 MB
Enter 'y' to accept these values and start the installation, or 'n' to
return to the beginning and make changes (y/n): y
Installing...
Installing Solaris software group
|-1%--------------25%-----------------50%-----------------75%--------------100%|
# ps -ef
UID PID PPID C STIME TTY TIME CMD
root 0 0 0 17:50:55 ? 0:00 sched
root 1 0 0 17:50:57 ? 0:01 /etc/init -r
root 2 0 0 17:50:57 ? 0:00 pageout
root 3 0 0 17:50:57 ? 0:11 fsflush
root 80 1 0 17:51:57 console 0:00 /bin/ksh /sbin/disk0_install
root 130 1 0 17:52:14 ? 0:00 /usr/sbin/syslogd
root 7407 250 0 19:10:06 console 0:00 ps -ef
root 32 1 0 17:51:01 ? 0:00 /usr/lib/sysevent/syseventd -r /tmp
root 34 1 0 17:51:16 ? 0:00 /usr/lib/devfsadm/devfsadmd -r /tmp -p /tmp/root/etc/path_to_inst
root 242 1 0 17:55:29 ? 0:02 /usr/sbin/nscd
root 250 80 0 17:55:30 console 0:00 sh
root 215 1 0 17:55:29 ? 0:00 /usr/sbin/rpcbind
root 238 1 0 17:55:29 ? 0:00 /usr/sbin/inetd -s
Any ideia whts going wrong?
Thanks for your attention,
Buy
Angelo FariaWell, there is no replys to this, so I presume no one else had this problem...
-
Using perl DBI on Solaris 10 gives core dump
I am using perl 5.8.4 which comes along with Solaris 10.
I have installed DBI-1.58.
Even a test command is not working.
perl -MDBI -e 'print "$DBI::VERSION\n";'
Bus Error (core dumped)
truss perl -MDBI -e 'print "$DBI::VERSION\n";'
shows
stat("/usr/local/lib/libc.so.1", 0xFFBFE5D0) Err#2 ENOENT
mprotect(0xFEED0000, 104171, PROT_READ|PROT_WRITE|PROT_EXEC) = 0
mprotect(0xFEED0000, 104171, PROT_READ|PROT_EXEC) = 0
munmap(0xFF370000, 8192) = 0
brk(0x000A2470) = 0
brk(0x000A4470) = 0
brk(0x000A4470) = 0
brk(0x000A6470) = 0
brk(0x000A6470) = 0
brk(0x000A8470) = 0
brk(0x000A8470) = 0
brk(0x000AA470) = 0
brk(0x000AA470) = 0
brk(0x000AC470) = 0
Incurred fault #5, FLTACCESS %pc = 0xFEED44CC
siginfo: SIGBUS BUS_ADRALN addr=0x00000001
Received signal #10, SIGBUS [default]
siginfo: SIGBUS BUS_ADRALN addr=0x00000001
$perl -v
command shows like its compiled with Intsize of 64 is this creating problem?
Summary of my perl5 (revision 5 version 8 subversion 4) configuration:
Platform:
osname=solaris, osvers=2.10, archname=sun4-solaris-64int
uname='sunos localhost 5.10 sun4u sparc SUNW,Ultra-2'
config_args=''
hint=recommended, useposix=true, d_sigaction=define
usethreads=undef use5005threads=undef useithreads=undef usemultiplicity=undef
useperlio=define d_sfio=undef uselargefiles=define usesocks=undef
use64bitint=define use64bitall=undef uselongdouble=undef
usemymalloc=n, bincompat5005=undef
Compiler:
cc='cc', ccflags ='-D_LARGEFILE_SOURCE -D_FILE_OFFSET_BITS=64 -xarch=v8 -D_TS_ERRNO',
optimize='-xO3 -xspace -xildoff',
cppflags=''
ccversion='Sun WorkShop', gccversion='', gccosandvers=''
intsize=4, longsize=4, ptrsize=4, doublesize=8, byteorder=87654321
d_longlong=define, longlongsize=8, d_longdbl=define, longdblsize=16
ivtype='long long', ivsize=8, nvtype='double', nvsize=8, Off_t='off_t', lseeksize=8
alignbytes=8, prototype=define
Linker and Libraries:
ld='cc', ldflags =''
libpth=/lib /usr/lib /usr/ccs/lib
libs=-lsocket -lnsl -ldl -lm -lc
perllibs=-lsocket -lnsl -ldl -lm -lc
libc=/lib/libc.so, so=so, useshrplib=true, libperl=libperl.so
gnulibc_version=''
Dynamic Linking:
dlsrc=dl_dlopen.xs, dlext=so, d_dlsymun=undef, ccdlflags='-R /usr/perl5/5.8.4/lib/sun4-solaris-64int/CORE'
cccdlflags='-KPIC', lddlflags='-G'
Characteristics of this binary (from libperl):
Compile-time options: USE_64_BIT_INT USE_LARGE_FILES
Locally applied patches:
22667 The optree builder was looping when constructing the ops ...
22715 Upgrade to FileCache 1.04
22733 Missing copyright in the README.
22746 fix a coredump caused by rv2gv not fully converting a PV ...
22755 Fix 29149 - another UTF8 cache bug hit by substr.
22774 [perl #28938] split could leave an array without ...
22775 [perl #29127] scalar delete of empty slice returned garbage
22776 [perl #28986] perl -e "open m" crashes Perl
22777 add test for change #22776 ("open m" crashes Perl)
22778 add test for change #22746 ([perl #29102] Crash on assign ...
22781 [perl #29340] Bizarre copy of ARRAY make sure a pad op's ...
22796 [perl #29346] Double warning for int(undef) and abs(undef) ...
22818 BOM-marked and (BOMless) UTF-16 scripts not working
22823 [perl #29581] glob() misses a lot of matches
22827 Smoke [5.9.2] 22818 FAIL(F) MSWin32 WinXP/.Net SP1 (x86/1 cpu)
22830 [perl #29637] Thread creation time is hypersensitive
22831 improve hashing algorithm for ptr tables in perl_clone: ...
22839 [perl #29790] Optimization busted: '@a = "b", sort @a' ...
22850 [PATCH] 'perl -v' fails if local_patches contains code snippets
22852 TEST needs to ignore SCM files
22886 Pod::Find should ignore SCM files and dirs
22888 Remove redundant %SIG assignments from FileCache
23006 [perl #30509] use encoding and "eq" cause memory leak
23074 Segfault using HTML::Entities
23106 Numeric comparison operators mustn't compare addresses of ...
23320 [perl #30066] Memory leak in nested shared data structures ...
23321 [perl #31459] Bug in read()
Built under solaris
Compiled at Jul 26 2005 05:26:55
@INC:
/usr/perl5/5.8.4/lib/sun4-solaris-64int
/usr/perl5/5.8.4/lib
/usr/perl5/site_perl/5.8.4/sun4-solaris-64int
/usr/perl5/site_perl/5.8.4
/usr/perl5/site_perl
/usr/perl5/vendor_perl/5.8.4/sun4-solaris-64int
/usr/perl5/vendor_perl/5.8.4
/usr/perl5/vendor_perl
Other details:
file /usr/bin/perl
/usr/bin/perl: ELF 32-bit MSB executable SPARC Version 1, dynamically linked, stripped
I tried installing DBI module using perlgcc also.
perlgcc Makefile.PL
make
make test
make install.
$uname -a
SunOS twirl 5.10 Generic_118822-25 sun4u sparc SUNW,Ultra-80
Please help me out.Try this guy's list, he maintain an archive of Solaris package.
http://www.ibiblio.org/pub/packages/solaris/sparc/html/creating.solaris.packages.html
Of course, if you can get directly from Sun will be better. -
PDF tab locked in Mozilla- Solaris
Hello,
I have an issue with the PDF tabs opened in Mozilla, We use Solaris 10 s10s_u4wos_12b SPARC and Adobe Reader 7 for Solaris.
When a PDF file is open in Mozilla Firefox, the PDF tab appear to be locked. The PDF file can be seen and scroll up and down but navigation to other tabs is not possible.
Can somebody help with suggestions and/or possible solutions?Hello John,
Which browser are you using to view PDF files? Also, to investigate the 'degraded graphic icons' issue, could you please share the PDF file you're trying to view (or share the link to the PDF file if it's online somewhere). You can send me an email at gaurav at adobe dot com.
When your tab is locked, do you have a dialog box opened on that tab? If possible, could you share a screenshot of the problem at the time the tab is locked.
Thanks,
Gaurav -
PDF tab locked in Mozilla -Solaris OS
Hello,
I have an issue with the PDF tabs opened in Mozilla, We use Solaris 10 s10s_u4wos_12b SPARC and Adobe Reader 7 for Solaris.
When a PDF file is open in Mozilla Firefox, the PDF tab appear to be locked. The PDF file can be seen and scroll up and down but navigation to other tabs is not possible.
Can somebody help with suggestions and/or possible solutions?Hello John,
Which browser are you using to view PDF files? Also, to investigate the 'degraded graphic icons' issue, could you please share the PDF file you're trying to view (or share the link to the PDF file if it's online somewhere). You can send me an email at gaurav at adobe dot com.
When your tab is locked, do you have a dialog box opened on that tab? If possible, could you share a screenshot of the problem at the time the tab is locked.
Thanks,
Gaurav -
Solaris 10 - Installing Errors - Dell Dimension 4100
Hello All,
I am tring to install Solaris 10 on a Dell Dimension 4100 system. I am getting an error, then the system reboots.
I am able to boot the Solaris 10 (03/05) DVD, I downloaded.
I get prompted : "Type of Installation you want to perform"
No matter which option I chose - I get the same results.
I get the msg: "Booting Kernel/Unix"
I then get the msg : "Configuring devices"
The screen flashing with information, then the computer reboots.
Computer Specs:
PIII 866mhz
256MB RAM
ATI 32MB Radeon
40G HD
DVD Writer
CD Writer
3COM NIC
SB Live
I checked in the BIOS - nothing about ACPI.
I am able to install multiple distros of Linux with no issues. I have not try to install any of the BSD's.
I tried to install Solaris 8, but I was unable. The issue was an open memory slot. I have 1 256mb memory card.
I was able to install Solaris 9 but I had an issue with a virus on my Windows side. I had to completly format the drive.
I have read alot aboiut Solaris 10 and wanted to give it try. I have installed via VMware.
I am tring to install only the Solaris 10 - no other OS will be on the HD.
Thank you in Advance,
HarryI don't know why Solaris is so good at finding faulty ram. Windows seems to instal but will crash randomly (Nothing unusual there :) so it's hard to say the memory is bad). I don't really use Linux that much so Ive never run it on a machine with faulty ram.
If we have a machine which is acting up in windows we simply try to boot solaris. If it fails then we change the ram and it usually fixes the problem. It's just our experience.
I hope that the second sim fixes your problem
Good Luck -
I have a Sparc 20. I am unable to get to miniroot using either Software 1 or Installation CDs (either Solaris 8 or 9 - isos downloaded and burned a variety of ways using both Nero and CD Creator).
The machine boots. The alias for the CD drive is correct (I've also tried a different CD drive with same result) but when I issue a boot cdrom -s command the machine begins to load from the CDROM, then after 20 to 30 secs or so, it just stops on the "hourglass". It has loaded some data from CD because the CD light is on for a good while and the "hourglass" does spin for several revolutions before it just stops. Should I be looking at memory? I can L1-A at this point just fine - so machine isn't completly frozen. Help appreciated?
The machine does boot fine using a Redhat port for SPARC (same type of CDRs - 700min - so that ain't the prob either).
Furthermore I have a Solaris 9 X86 machine working fine on net. Can I use this as a Install server for a net boot on the SPARC (sounds like no from what I've read). If someone can point me to useful help on this it would be great. I understand that the filesystems on the Sparc CDs can't be read on X86 Solaris.
Anyway - distinct Newbie on Sun HW... Comming from SGI background. Excuse the old hardware - it's all I've got for the moment.
Anything will be helpfulMy SS20 was super picky when it came to the speed of the burned media, but only for Solaris for some reason. I burned Aurora 1.0 at 32x and It was good to go, but Solaris 9 cried when I burned it any faster than 4x.
Have you tried burning it at 4x, or even 1x?
It also takes what seems like AGES to load up from the Solaris install CDs, and unless your using 10K RPM SCSI with 256+ Mb of RAM, expect it to take 6-12 hours to install the OS from the stock CD-Rom on an SS20.
Maybe you are looking for
-
Hi After just fixing my wifi problem (http://discussions.apple.com/thread.jspa?threadID=1345209) I am able to access the internet but I have a problems loading pages from some websites. The browser will say that I have loaded the page fully, but none
-
Thunderbolt to Firewire target disk mode?
I've got an iMac (TB and FW) and a brand new MBA and I want to connect them in target disk mode to do file transfers. I don't want to buy a TB cable as a TB-FW adaptor would be more useful (I have a FW audio interface) whereas it seems a TB -TB cable
-
Easy one I hope: How do I change text color?
For the life of me I can't seem to find anything with a color pallette (except for background fill). I need to change text color but don't know where to find it. Everything's always black. When I highlight the text, and goto "Font", I see something
-
My iMessage won't work on my iPod touch 4g
It use to work and then one day it stopped it says after in with my apple ID it said you could not sign in please check your network connection and try again later
-
Pages in not shown in indesign
On my page window is not showing all the pages I have, this is something to do with the setting? How can I get my thumbnail pages back into the pages window?