"Recovery Partition has been Removed" Message in Recovery Media Creation

HP Pavilion G4 2205tx - C5j09PA#UUF
Windows 8 64-bit
"Recovery Partition has been Removed" Message in Recovery Media Creation.
i bought My new HP pavilion G4 laptop just two days ago and didnt change any thing in two Drives named Drive C: for windows and D: for HP Recovery.
now i want to Make a Recovery Disk with HP Recovery Manager Software.
but it show a Massage: "Recovery Partition has been Removed" in Recovery Media Creation Section.
in My Computer Recovery Partition is Almost Full (3.26G of 25.5G is Free) . so i think Recovery files present there .
i haven't any Access to HP for Buy recovery disk or Call Support.
Thanks
This question was solved.
View Solution.

I don't know why your PC is saying your partition is gone - you're right, it doesn't look gone. I do know that if you use the Support Assistant to make backup copies of your Recovery Disks and Then instruct it to remove the recovery partition to give you more space on the hard drive, it will delete the HP factory image of Windows 8 from the recovery partition and leave the normal Windows repair tools behind.
There are tools however that allow you to create your own recovery partition complete with these Windows repair tools and a new image of your instalation so you can restore from that. You could use this tool: Windows 7/8 - OEM Recovery Partition Creator found here: http://forums.mydigitallife.info/threads/21978-Windows-7-8-OEM-Recovery-Partition-Creator but thats a lot of work and it would be faster and easier just to backup your data and restore from your HP recovery disks you made from Support Assistant. If you didn't make the disks, HP may opt to send you a copy.. they do not normally do this but I have read that some people have good luck getting a free copy of the media from HP.. otherwise they want you to buy the recovery disks ($40.00) . I suppose it depends on the exact circunstances of your situation.
Another solution is to use Macrium Reflect Free Edition to ghost or clone your system. You can then restore your whole system even with your custom programs installed, to the exact state it was in when you made the backup image. ( this may take several dvd's) I suggest you go this route because restoring your system with Macrium Reflect is Much faster than restoring from the HP Recovery Disks. Even if you do obtain another copy of the Recovery Disks, you should use this tool to make another backup that you can customize to your liking. Your re-installs will be faster, they will already have your chosen software installed, and you will save wear and tear on your HP Recovery Disks. You can then safely delete the recovery partition to gain back that space on your hard drive (since you cannot access it anyway, you won't need that space being taken up). BUT.. you cannot restore from UEFI Mode which is what HP ships with. You have to go into your Bios settings, and switch to Legacy Bios mode, (which disables Secure Boot) FIRST or else the Macruim recovery boot disk will not load to install the recovery image. After the system re-installs you can go back into bios settings and disable Legacy bios and re-enable secure Boot if you like. ( Windows 8 will load in both UEFI mode with secure boot enabled or Legacy bios mode.. it's your choice. UEFI mode will load faster but it will cause problems if you want to dual boot the system with another OS) Hope this helps.

Similar Messages

Recovery partition has been removed

Hi sir
I recently purchased a HP pavilion g-1202 TX series, I have installed Windows 7 64-bit OS, I found that I had only single drive i.e. C: for use, thought of creating another partition and shrunk the C drive, after this I found that HP RECOVERY MANAGER SAYS "Recovery partition has been removed - the recovery media creation option is no longer available"
Then again I tried expanding the C: drive back to its old stage, even then I found the same error, Now how can I get back HP RECOVERY.? and create Recovery Partition?

if you havent created the recovery media already from your computer, there is only option to get media from HP.
contact HP to order Recovery media. in most countries you can order it online, else contact HP phone support.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=bph07143
if no option to order media for your country, contact country HP support.
visit www.hp.com and select country from the left botttom. now select contact HP or connect with HP. reach support to get a set of recovery media to make your computer recover and work as factory install.
hope it helps. Good Luck !!!
Regards,
WW
“I am an HP Employee“
***** Click the KUDOS star on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem***

Recovery drive has been removed

hi
i have a pavilion dv6 - 2140se
my recovery partition has been removed
i want buy and download it
please help me

Here are the specs for your HP Pavilion dv6-2140se Entertainment Notebook Computer. Sorry, but HP can't and/or doesn't make Recovery images available for download. Please contact HP, in your region / country, via the HP Worldwide Support Portal to check on the availability of HP Recovery Discs for your computer.
If you have any further questions, please don't hesitate to ask.
Please click the white KUDOS star to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

SL500, Product recovery function has been removed from this sytem

I upgraded my SL500 from Vista to windows 7 OS several years ago and lately the OS has been acting weird (freezing, very slow at times) so I am thinking something is corrupted somewhere and want to restore it back to the manufacturers state. However, when I try to do this through rescue and recovery, it tells me that the recovery function has been removed from the system. I'm assuming that when I upgraded from Vista that R&R was no longer compatible so I installed version 4.5. My laptop did not come with backup OS disks and was told that this was the way to restore the system back to the factory state. How do I do this if I'm getting this message?

http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-62978
try this. If this don't work then you would to reinstall the OS using the T43 recovery media disk set.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Recovery partion has been removed...help!!!

i have a a pavilion dv6090 laptop and i noticed that its recovery partion has been removed.i dont know how it hapend the only thing that i know is that i havent removed it myself.can anybody tell me me how to fix this problem??

Hi,
I've replied on your earlier thread on the link below.
http://h30434.www3.hp.com/t5/Notebook-Operating-systems-and/recovery-partion-has-been-removed/m-p/75...
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

The Product Recovery function has been removed from this system

I get the following error when I try full system restore - "The Product Recovery function has been reomed from this system"?
How can I fix this?

welcome to the forum:
Have you made a recovery media before this problem occured??? if you haven't you may need to call Lenovo and ask for a set of recovery disks, or just use your own XP/Vista OS you got from somewhere, and load it on your machine then enter you own serial number that come with your machine.
Then proceed to download the various softwares and drivers applicable to your machine, the most important that you won't have is the predesktop area, if you think this is unacceptable then call Lenovo and obtain recovery media from them (a nominal handling and service charge of around 50 USD will be charged).
http://www-307.ibm.com/pc/support/site.wss/product.do?doctypeind=9&template=%2Fproductselection%2Fla...
fill in the detail and download away.

Recovery Partition has been deleted.

Is there a way to format my computer without this partition? Is there a way to recover this partition?

Satellite C655-S5514
If you have failed to burn recovery discs, you can obtain them from Toshiba.
Get Recovery Media
For instructions, see the section Restoring from recovery DVDs/media, which begins on p. 76 of the User's Guide.
Satellite/Satellite Pro C600 Series User’s Guide
-Jerry

The recovery partition from my hp presario cq50 104ca notebook has been removed, if you are able to

Hi to all
Assume that the recovery partition from my hp cq50 104ca has been removed because in the past many times, I could reset back to factory setting, just by holding down alt and control and f11 by starting point. But now since few weeks can not do it. If you are able to assist me with that issue however.
Thank you in advance
Munir

Hi Munir,
If you have created your set of Recovery Discs, you can use these to reinstall the operating system - this procedure will also re-create the Recovery Partition on the Hard Drive.
If you don't have these discs, you can order a replacement set of Recovery Discs using the link below.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00810334&cc=us&lc=en&dlc=en
If you have any problem with this link, order them directly from HP.
If you live in the US, contact HP Here.
If you are in another part of the world, start Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Hard Drive Recovery Process has been selected

One day, while playing a game online, the computer screen went black and a blue box appeared that said "Hard Drive Recovery Process has been selected Press Yes if you wish to continue " Also, there was NO which only shut the computer down. YES took me to a blue screen with recovery and troubleshooting options. At first, none of these worked, or stayed. Because the next time I used my computer I would get the same Hard Drive Recovery Process message and had to try various things to make it work. I did purchase a Windows 8.1 recovery flashdrive from Toshiba and attempted to install it. It took about 6 tries for it to completely install. However, after installing, I was unable to use the RESTART option to power off the computer as it would trigger the Hard Drive Recovery Process again ! Ugh ! Last night, I powered the laptop off using SHUT DOWN and in the morning, I got the Hard Drive Recovery Process screen again, much to my horror. I have Norton Internet Security and Anti Virus as well as I used Toshiba maintenance tasks and no problems were found. I would appreciate any information on troubleshooting and repairing this problem, if there is a solution. Thanks !!!!!

I did purchase a Windows 8.1 recovery flashdrive from Toshiba ... after installing .. it would trigger the Hard Drive Recovery Process again
The fact that the problem remains after restoring the hard disk to its original out-of-the-box contents using Toshiba recovery media means the software doesn't cause it.
The computer needs servicing.

After downloading osx 10.9.2 when i open my logic pro 9 and begin to audition loops that came with lp9 i get a message that says "audio device has been removed and then a second message the " select driver not found(-10202). my interface is a apogee duet

after downloading osx 10.9.2 when i open my logic pro 9 and begin to audition loops that came with lp9 i get a message that says "audio device has been removed and then a second message the " select driver not found(-10202). my interface is a apogee duet. Can anyone provide a solution to this problem. Thanks

YES!!! YES!!! YES!!!
I got it!!! Yes!!!
Guys, I've solved my problem about that error -10202 (Selected driver not found).
I have installed in my Mac Pro (OS X 10.5.8) a document with an extension ".rsrc" to correct the position of the accents in my keyboard, like acute accent, tilde and circumflex.
That file is called "U.S. - International.rsrc" and it's stored in the following path:
"Macintosh HD/Library/Keyboard Layouts"
So, when it's properly installed, I can choose 2 country flags on the right side of the menu bar (U.S. - International and Brazilian).
That's the clue!
When I pick up "U.S. - International", my keyboard works fine with the accents, >>>BUT<<< Logic Pro 9 doesn't recognize my audio driver; and when I pick up "Brazilian", my keyboard doesn't work with the accents exactly as it shows me on each key, BUT Logic Pro 9 DOES recognize my audio driver.
So, when I want to write anything out, I will pick up the "US - International" and when I want to work on the Logic Pro 9, I will pick up "Brazilian".
I hope I can help all of you.
Regards,
Renato Veiga.

Recovery partition has disappeared

Hi, after installing Mountain Lion the system was running perfectly. But now my recovery partition has disappeared. Is there any way to recover this partition without installing the whole system?
Thx a lot ...

You have no recovery partition. This is a normal condition if your boot volume is a RAID, or if you modified the partition table after running Boot Camp Assistant to create a Windows partition. Otherwise, you need to reinstall OS X in order to install a recovery partition.
If you don't have a current backup, you need to make one before you do anything else, unless of course you have no data you want to preserve.
You have several options for reinstalling.
If you have access to a local, unencrypted Time Machine backup volume, and if that volume has a backup of a Mac (not necessarily this one) that was running the same major version of OS X, then you can boot from it into Recovery by holding down the option key at the startup chime. Encrypted Time Machine volumes are not bootable, nor are network backups.
If your Mac shipped with OS X 10.7 or later preinstalled, or if it's one of the computers that can be upgraded to use OS X Internet Recovery, you may be able to netboot from an Apple server by holding down the key combination option-Rat the startup chime. Release the keys when you see a spinning globe.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with networks that require any kind of authentication other than a WPA or WPA2 Personal password.
If your Mac is unable to use Internet Recovery, the simplest solution would be to run Recovery Disk Assistant on another Mac to create a bootable recovery device.
When the OS X Utilities screen appears, follow the prompts to reinstall the OS. You don't need to erase the boot volume, and you won't need your backup unless something goes wrong. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with networks that require any kind of authentication other than a WPA or WPA2 Personal password.
If none of the above options is available to you, then you'll have to start over from an OS X 10.6.8 installation. There's no need to overwrite your existing boot volume; you can use an external drive. Install 10.6 from the DVD you originally used to upgrade, or that came with the machine. Run Software Update and install all available updates. Log into the App Store with the Apple ID you used to buy 10.7 or later, and download the installer.

When I try to download and install the latest software version of iTunes, this message occurs: "iTunes has an invalid signature. The download has been removed." Any suggestions?

When I try to download and install the latest software version of iTunes, this message occurs: "iTunes has an invalid signature. The download has been removed." Any suggestions?

You seem to have an iTunes problem and not an iPod problem. I suggest posting in the iTunes forum.
How areyou doing the download?
From Apple's site?
Via the Apple downloader
PC or Mac?

I can't remember the security questions and recovery email has been shutdown. How can I get back to purchasing songs, apps, etc.?

I don't remember the security questions and my recovery email has been shut down after years of no activity. What can I do to get back to purchasing music, apps, etc.?

The Three Best Alternatives for Security Questions and Rescue Mail
    1. Use Apple's Express Lane.
          Go to https://expresslane.apple.com ; click 'See all products and services' at the
          bottom of the page. In the next page click 'More Products and Services, then
          'Apple ID'. In the next page select 'Other Apple ID Topics' then 'Forgotten Apple
          ID security questions' and click 'Continue'. Please be patient waiting for the return
          phone call. It will come in time depending on how heavily the servers are being hit.
     2. Call Apple Support in your country: Customer Service: Contact Apple support.
     3. Rescue email address and how to reset Apple ID security questions.
A substitute for using the security questions is to use 2-step verification:
Two-step verification FAQ Get answers to frequently asked questions about two-step verification for Apple ID.

My ipad has been stuck in a recovery mode and i cant restore it through my laptop due to less internet speed. can i submit it to apple store? will they make it alright?

my ipad has been stuck in a recovery mode and i cant restore it through my laptop due to less internet speed. can i submit it to apple store? will they make it alright?

Hello Elliiee,
The steps detailed below can help stabilize your iPhone.
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If the display turns on, go to step 4.
If the display remains black, go to next step.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
My issue is still not resolved. What do I do next?
Contact Apple Support.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Cheers,
Allen

Goods receipt when PO creator has been removed from org structure ?

Hello in my organisational structure PPOMA_BBP, i have 2 users, X and Y.
X has created a PO in the SRM portal.However , X has been removed from the org. structure.
Is it possible for Y to make the goods recept( that is , Y logs in the portal and makes the goods receipt) ?

Hi
Did you try to delete the user ? Did you get any error message?
Note 1148837 - SRM user cannot be deleted
When trying to delete an SRM user the system will check if there are still
related SRM documents in the system. If there are active documents in the
system the deletion is not possible. This is the correct system behaviour.
But even if all related SRM documents are archived the deletion is
sometimes not possible, because there are residual entries in table
CRMD_PARTNER linked to this user.
More Terms
User crmd_partner residual entries deletion active document
Cause and Prerequisites
Solution
The attached report PARTNER_SET_DELETE will display in simulation mode all
residual entries in table crmd_partner with invalid item or header links
and in non simulation mode it will delete the corresponding crmd_partner
entries.
Header Data
Release Status: Released for Customer
Released on: 10.03.2008 11:54:37
Priority: Correction with low priority
Category: Help for error analysis
Main Component SRM-EBP-PD Procurement Document Methods
Additional Components:
SRM-EBP-ADM-USR SRM User Administration
Valid Releases
Software Component Release From
Release
To Release and Following
SRM_SERVER 500 500 500
SRM_SERVER 550 550 550
Support Packages
Support Packages Release Package Name
SRM_SERVER 500 SAPKIBKS14
SRM_SERVER 550 SAPKIBKT12
Correction Instructions
Ref note 550071 too..
regards
Muthu

"Recovery Partition has been Removed" Message in Recovery Media Creation

Similar Messages

Maybe you are looking for