Remote access is rejected by the default configuration?

I installed a SunOne Directory Server 5.2 following the installation wizard. I can access it from a LDAP browser installed on the same machine. However, when I tried to connect the service from a remote machine, it gives me "[ERROR 91] Can't connect to the LDAP server". The server and the client machine are in the same domain and don't have access problem for other services ( http, soap...etc).
Does anybody know what the problem might be? Is there any particular setting in SunOne Directory Server that controls this.
Thanks in advance.

Hi,
Sun Directory Server 5.x requires fully qualified domain names that can be resolved from all machines.
Make sure the hostname contains a DNS name.
Regards,
Ludovic.

Similar Messages

URL file-access is disabled in the server configuration

My hosting company has made a server config change and my xslt pages have stopped working with the following error.
It says url file access is disabled but my phpinfo() still shows allow_url_fopen = on
What else might be the problem?
Warning: require_once() [
function.require-once]: URL file-access is disabled in the server configuration in
/homepages/0/xxx/htdocs/xxxx/inc/horoscope_xml.php on line
3
Warning: require_once(
http://www.xxxx.co.uk/includes/MM_XSLTransform/MM_XSLTransform.class.php) [
function.require-once]: failed to open stream: no suitable wrapper could be found in
/homepages/0/xxxx/htdocs/xxxxx/inc/horoscope_xml.php on line
3
Fatal error: require_once() [
function.require]: Failed opening required 'http://www.xxxxx.co.uk/includes/MM_XSLTransform/MM_XSLTransform.class.php' (include_path='.:/usr/lib/php5') in
/homepages/0/xxxx/htdocs/xxxxx/inc/horoscope_xml.php on line
3

bikeman01 wrote:
I don't understand your use of the word 'class' in your reply - I am using php not asp.net.
The name of the file that you are trying to access is MM_XSLTransform.class.php. It is a PHP class created by Dreamweaver for the XSL Transformation server behavior.
The servers php is 5.2.11, as it has been for sometime, so I know that it previously worked with allow_url_fopen = on and allow_url_include = off
Judging from the error message, you are trying to include the file using a URL, rather than a file path:
Fatal error: require_once() [
function.require]: Failed opening required 'http://www.xxxxx.co.uk/includes/MM_XSLTransform/MM_XSLTransform.class.php' (include_path='.:/usr/lib/php5') in
/homepages/0/xxxx/htdocs/xxxxx/inc/horoscope_xml.php on line
3
Change the URL to a file path:
require_once('/homepages/0/xxxx/htdocs/includes/MM_XSLTransform/MM_XSLTransform.class.php');
Is it possible for phpinfo() to show allow_url_fopen = on yet be actually off on the server?
No.
[Edited to correct name of server behavior]

Configuring the default configuration profile for Profile Manager

Hello folks,
I would like to edit the default configuration profile served by Profile Manger. As far as I understand the only thing I can configure from the Server.app is the name of the profile. The settings for the different services provided by the server (such Mail, Messages, etc.) are automatically chosen by Server.app. When logging as an administrator on the Profile Manager webapp, I can go to "Groups", choose "Everyone", go to "Settings" to review the different payloads. However, almost none of the settings are editable. You can read "This payload is configured using the Server app" on the top of the various panels.
So my question is: How do you use Server to tweek those payloads? Can this be done using the serveradmin command line tool?
Thank you very much for your help.
Regards

Bump. This is annoying the crap out of me. Every time I try to design a website using Coda, this color picker bug plagues me. I just wish I could turn off color profiles completely as I will never use them.

If remote access is allowed on the server, Then can my users on the local network access this server by ie

Dear all,
If my server is enabled for the remote desktop connection, then the users on the local network can access my server IIS services by entering the IP address of my server in the IE (http/https) on the local network only.
I went to control panel>>system>>Allow Remote desktop Connection>>with network level authentication.
Now If my team wants to access this server not by opening the Remote Desktop Connection, rather by entering the IP address of my server on the IE and access the resources offered.
Is it possible by this way,
Or is there any other method to do so.
Regards,
Ahmed

3. My web Developer is installing an application on the server for our department team. To test this application running, he wants to access this application through the local machine from browser (rather than logging in through the remote desktop connection).
4. He wants this application to run on the local network only.
5. He wants me to do some setup, that he must be able to enter the IP address of the server in the browsers address bar on his local machine and test the functionality of his application on the local network.
If this is the requirements of the developer, I guess he wants you to configure IIS.
You can do a test, whether IIS is working properly.
Log on to server, enter https://localhost or http://IP_address_of_the_server don't know whether some ports are configured in order for your IIS to work.
check out this youtube video:
https://www.youtube.com/watch?v=tNAdv1EPj-I
Every second counts..make use of it. Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
IT Stuff Quick Bytes

Remote Access to Windows 2008 R2 Server configured with local IP

Hello,
I have a Windows 2008 R2 Server configured with local IP (e.g. 192.168.1.115).
Please how can I access it remotely outside its local domain through (remote desktop connection).
Thank you.
Tony.

Hi Tony,
Based on your description, you would like to connect to the Windows 2008 R2 server via remote desktop connection.
So you need to enable remote desktop on the Windows 2008 R2 server if it is not already.
1.Install and configure the Remote Desktop Session Host role service in the Windows 2008 R2 server.
2.Add related user to the Remote Desktop Users group in the Windows 2008 R2 server.
3.Configure remote desktop connection in the Client.
Also, due to you would like to access it remotely outside the domain, so you will need a VPN connection or a port forward to connect through.
For more details, please refer to the guide below,
Installing and Configuring Remote Desktop Session Host
http://technet.microsoft.com/en-us/library/dd883253.aspx
Allow Remote Desktop connections from outside your home network
http://windows.microsoft.com/en-IN/windows7/allow-remote-desktop-connections-from-outside-your-home-network
Best Regards,
Tina

Routing And Remote Access Service: Error 1068: The dependency service or group failed to start

Hi,
I tried to establish a PPP connection between my windows 8.1 PC and another kind of machine using an USB cable. So, as usual on Windows XP and Windows 7,
I configured the COM in the modem list and I tried to start the
"Routing And Remote Access" service and then
I got this message.
So any idea why is failing?
Please help!
Thanks thaks thanks

Hi,
Was your issue resolved?
If no, please reply and tell us the current situation in order to provide further help.
Karen Hu
TechNet Community Support

How can I change the default configuration of PO print ?

**When I print list which type is ALV ,I can choose any one OUTPUT Device and printer.**
**But I print PO which type is SCRIPT by trail printout, I can not to choose printer ,it will be printed on my default windows printer.**
**It dosenu2018t means that the default setting of user is incorrect. I find that PO print has dedicated out type ,it includes form,page,process routines, etc.(transcation code :NACU)**
**I am not sure which parameter control the immediate print,how can i control PO print not immediately and I can choose own output device and printer ?**

> **When I print list which type is ALV ,I can choose any one OUTPUT Device and printer.**
> **But I print PO which type is SCRIPT by trail printout, I can not to choose printer ,it will be printed on my default windows printer.**
> **It dosenu2018t means that the default setting of user is incorrect. I find that PO print has dedicated out type ,it includes form,page,process routines, etc.(transcation code :NACU)**
The printer chosen is configured in the SD customizing, there are quite many options how to configure that.
> **I am not sure which parameter control the immediate print,how can i control PO print not immediately and I can choose own output device and printer ?**
You can find the settings in
- transaction SPRO
- SAP IMG
- Sales and Distribution
- Basic Functions
- Output Determination
Usually it's not a good idea to print locally, this is especially not possible when something is processed in the background.
Markus

Need the default configuration of map-class and policies for WAAS version 5.3.1.20

Do someone have the default configuraion cli of class-maps and policies for the WAAS version 5.3.1.20. I need this to compare with the configuration that I have in the network, I need the verify what have been changed.

I'm sure you figured this out already since it's been 9 months. But just in case someone needs this - you can restore the default policies if they don't show up. Device Groups -> AllWAASGroup and edit. There you will see a "Restore default Optimization Policies"

Hotmail Security, the default configuration through the wizard uses SSL?

I was wondering if there is a way to check the server settings used by the default wizard when you add an hotmail account to your device (iPad , iPhone or others). The main concern is if it uses actually the SSL encryption or not. I think so and I hope so but I'm not sure 100%. If you go to check it there's not an advanced tab under Mail/Account/nameofaccount/ so you can't see that. Thanks to everyone!

Should this be a security concern that I am using the
default keystore that comes with the JVM. Is my data
still be encrypted?When you say, "default keystore", I assume that you mean the "cacerts" file. If so, you're OK. "cacerts" identifies root CAs that your client is willing to trust. Web sites whose site-certs are signed by one of the root CA in cacerts (i.e., Verisign, Thawte, et. al.) will be trusted by JSSE.
SSL generates shared-keys anew for each new session. The data used to generate this "shared secret" is protected; unless the Bad Boy between you and the server has access to the SERVER's private key, that info is safe. Your data is encrypted over the wire, and only the destination web-server will be able to decrypt it.
Grant

Remote access to PC from the Internet over a DSL connection!

Hello! I have a PC on the local LAN which is hooked to the Internet over a DSL Modem (Speedstream 4100) connection using a 2620 Router with 12.3 IOS. A remote vendor wants to access this PC using "Port forwarding" to Port 3389. He was able to do this using a Linksys Router instead of a 2620.
There are no leased public IP addresses on this connection. The vendor was able to use some DDNS to accomplish this successfully. Now, the Linksys Router has been replaced with 2620 and I need help configuring this.
Any ideas? Thanks in advance!

Try:
ip nat inside source static tcp 3389 interface fastethernet0 3389
If the IP address for FA0 is dynamic, you can use DDNS as mentioned (requires additional configuration), or simply look it up in the router and communicate verbally to the vendor.
Hope this helps, please rate post if it does!

Server used to be listed on Remote Access web page before installing and configuring RemoteApp. Now it's gone.

I am new to RemoteApp. I have been using WSE 2012 R2 for some time, mainly for the remote web access web site. I would log into my site (<my name>.remotewebaccess.com/Remote). Then, I would see my server listed under "DEVICES".
I would click on the tile for the server, and the Dashboard would open.
I just followed a tutotial to install the role for RemoteApp publishing. It looks like it worked. I now go to my RD Web App site (<my name>.remotewebaccess.com/RDWeb), and I can log in and see my RemoteApp. But now I cannot
figure out how to get to my server's Dashboard, because when I go to my main web acess site (that ends with "/Remote"), the server is not listed under devices.
Ideally, I would like to see all of my computers, including the server, on the main Remote Web Access site. Also, it would be great if I could see my RemoteApps there too. But I don't know if that is possible. Can anyone help me get
to that state, or know if what I want is possible? I want everything on the same web page:
Devices
Shared Folders
Links
RemoteApps

Hi,
Based on your description, I understand that DEVICES tab disappears from Remote Web Access website after RemoteApp
configured. If anything I misunderstand, please don’t hesitate to let me know.
à
But now I cannot figure out how to get to my server's Dashboard, because when I go to my main web acess site (that ends with "/Remote"), the server is not listed
under devices.
Did all users encounter the same issue when access RWA? Please open Dashboard and navigate to USERS tab, then
click the problematic user account and select View the account properties. In Properties of this user account, please navigate to Anywhere Access, then please check if Computer option was checked in
Show selected links on Remote Web Access. Meanwhile, please also use an administrator user account to check if this issue still exists.
In addition, please follow the path: C:\ProgramData\Microsoft\Windows Server\Logs\WebApps folder and check
RemoteAccess log file if find more clues.
Hope this helps.
Best regards,
Justin Gu

Remote access VPN to server from outside and server reach internet on the same time

Dear,
I have problem in my ASA 5515-X , when i make Remote access VPN to servers in inside zone the internet connection disconnected in the servers, or when i have internet in servers, the remote access cant reach servers.
the configuration for server as static NAT for each server, and the connection of VPN is to another public IP but in the same subnet of NAT ip.
server1 : 10.10.10.2 nat to 5.6.7.8
server2: 10.10.10.3 nat to 5.6.7.9
server3: 10.10.10.4 nat to 5.6.7.10
VPN connection to 5.6.7.12
is there any solution for this senario, remote vpn to servers and the same time the servers have internet readability for download updates .. etc

Hi,
So it seems that the problem is with lacking a NAT0 configuration
You could modify the below configuration to match your networks/IP addresses used. In the below configuration I presume that you have interfaces "inside" and "outside".
object network SERVER-NETWORK
subnet <server network address> <network mask>
object network VPN-POOL
subnet <vpn pool network address> <network mask>
nat (inside,outside) 1 source static SERVER-NETWORK SERVER-NETWORK destination static VPN-POOL VPN-POOL
Just insert the correct address related information and change the "object" and interface names if required.
This configuration will tell the ASA that no NAT will be performed for traffic between the VPN-POOL and SERVER-NETWORK. The NAT configuration is bidirectional. With this configuration the Static NAT configurations will continue to work for the servers Internet traffic and this NAT0 configuration will be applied only to the VPN Client traffic.
Hope this helps :)
- Jouni

How to retrive the overwritten SAP Default Configuration

Hi There,
I was trying to enhance the component BT115IT_SLSO to add some new fields into the table view Items.
I copied the view configuration to my Z config key but by mistake & added the fields into the default view and saved the changes. Now the default configuration is screwed up.
Can some one point out how to retrive the SAP standard configuration( where it is stored ). In the configuration tab of the view the configuration looks ok but in Web UI I see all the columns available in the context node, and makes the view useless, when I go to the personlization of the view all fields shows the message < Error in Meta data > and I can not see the details of the fields.
I have already backed off my enhancement. Now I want to retrive the view configuration.
Your help will be highly appreciated.
Thanks,
Vikash.

Issue resolved.
Solution was In BSP workbench when I went to choose configuration I saw that just next to std conf there was column for cust conf. and both were marked X so I deleted the conf and that gave me the standard conf back.
Thanks,
Vikash.

Is "remote access" is the best solution here?

Dear;Helpers
1st .. Thanks you anyway
that's my Topology in the figure
i57.tinypic.com/23mv5v9.png
Required:
To access the local website from the tow Ranges.
Suggestion:
To enable “remote access” for IIS (the local site) , so we can visit it on the Internet, or whatever the solution.
Note: Static IP is Supplied.
i know i can do it, if you helped me ..
need the steps..
A friend advised me to make a "remote desktop" instead of "enable routing & remote access"
could i?
Thanks all anyway

Hi,
Based on the figure you provided, I would like to know if the 192.168.3.0 network is a branch office in different location.
->To enable “remote access” for IIS (the local site), so we can visit it on the Internet.
If computers of the 192.168.3.0 network want to access the local website in 192.168.2.0 network through Internet, you should set up VPN connection. If you want to use remote desktop connection, the remote clients also need to connect to the 192.168.2.0 network
through Internet at first. And if the remote access clients connect to the 192.168.2.0 network through VPN, it can access the local site without other operation.
Best Regards,
Tina

How do I set the active configuration back to default in NI MAX?

In the traditional NI-Daq menu of NI-MAX, I inadvertantly changed the active configuration away from the default, in which I had already set up channels. How do I get back to the configuration where I had the channels already set up?
Thanks,
KHC

Hello KHC,
So you configured some channels and now you want to go back to the default configuration? There isn't an option to right click on the task to change it. You will have to open a new task or modify the current task.
If you had created a task, modified it, saved it, modified it again, and wanted to go back to the first modification, you could just close MAX without saving the task. When you opened it again, the first modification would be there. Please let me know if you have any questions. Have a great day!
Sincerely,
Marni S.

Remote access is rejected by the default configuration?

Similar Messages

Maybe you are looking for