Remote issues, help requir
Well, I have an Audigy 4 (OEM), that doesn't come with the remote.
Well, some ebaying got me the remote (rm-500) and the receiver, but not the drivers disc (I still have the original drivers disc for my Audigy 4 though). I can't get the remote to work, I don't have remote center installed despite having done a full installation.
Is there something I've missed? Can someone help me please?
The remote signals btw.
got it working. is there a plug-in for jetaudio and remote?
It's almost funny how I could change volume in jetaudio, switch tracks, close the program, all with the remote, yet I can't PAUSE the music!Message Edited by alexdark on 08-28-2006 05:43 PM
Similar Messages
-
DVR/STB/Remote issues - Help Needed
New to Verizon FIOS (Installed about 2 weeks ago). Have a few issues. Any help is appreciated
1) When im on the Home Media DVR and i fast forward through a program, when i stop or hit play, an extremely loud beep that lasts for 1-3 seconds comes from the speakers. How do i get this to stop, what is causing it, etc?
2) When i fast forward from one of the STB (regular HD box), if i hit FF once, it fast forwards pretty slow, if i hit it again, it goes somewhat faster. The problem is. When i hit it that 2nd time, it seems that 70-80% of the time, it jumps me back to an early portion of the program. I.E. Was watching the 2 hour episode of "24", was one hour and 20 min in, got to commercials, i hit FF twice and it jumped me back to 23 minutes in. Tried again at next commercial break and it jumped me back to 11 minutes in. What is the deal here? How do i fix it?
3) Are there only 2 fast forward speeds on STB? I came from Brighthouse that had 4 speeds, im a little disappointed with only 2 speeds. Can anyone verify?
4) The remotes seem to take 2 seconds or so to register when performing any function other than changing channels. When i hit FF or REW, DVR or Last, it seems to take a few seconds to kick in. Is this a known issue, or possibly my box or remotes?
Thanks for any and all helpSorry the ff speeds are the same. On the main MR-DVR there are 3 ff speeds, where the remote STB has 2 ff speeds. I think they did that because how the remote system works, it has slower responses being remote. But with the update you will not need to worry about the ff, because you will not get the hub error. I was one of the first people to get the update and I have not seen the hub error yet.
As far as a time frame I don't believe there is any thing public about it, I think the only thing they have said is it is going to be rolled out per market, and one market a week. But nothing on the order of the markets. -
About Running Remote Search Helps in SRM via Webdynpro ABAP
Hi there,
I am having troubles trying to implement an input help for a custom field in the standard Shopping Cart Portal page for item level.
I would like to implement the same input help used in field Network of Activities, but as I can see in WDA component '/SAPSRM/WDC_UI_DO_ACC', it seems to use another component in order to run a remote Search Help (I assume it is an original search help from PS system).
Does anybody know how to use this backend search help WDA Component? (/SAPSRM/WDC_UI_BACKEND_SH)
I haven´t found any information regarding that :S.
Another option would be to create a new RFC FM in PS returning the expected values, and use these entries to build a list value selector associated to the corresponding context attribute (This is not what I would like...)
Thanks in advance!Vicente Ángel Lopez Romero wrote:
> Hi there,
>
> I am having troubles trying to implement an input help for a custom field in the standard Shopping Cart Portal page for item level.
>
> I would like to implement the same input help used in field Network of Activities, but as I can see in WDA component '/SAPSRM/WDC_UI_DO_ACC', it seems to use another component in order to run a remote Search Help (I assume it is an original search help from PS system).
>
> Does anybody know how to use this backend search help WDA Component? (/SAPSRM/WDC_UI_BACKEND_SH)
>
> I haven´t found any information regarding that :S.
>
>
> Another option would be to create a new RFC FM in PS returning the expected values, and use these entries to build a list value selector associated to the corresponding context attribute (This is not what I would like...)
>
> Thanks in advance!
Figured it out.
/SAPSRM/WDC_UI_BACKEND_SH is a 'freely programmed' search help used in SRM.
1. Add this helpview (HV) component usage to your component controller, and view controller.
2. Map HV SELECTION context to your view
3. Modify the context attribute you want backend searchhelp to 'freely programmed', and select the component usage created in step above (note this is done dynamically in SAP code, b/c attribute is defined as dictionary search help in SAP components) -- this took a bit to figure out.
4. IMPORTANT: Give your context attributes the SAME NAME (COST_CTR in my case) as those in structure /SAPSRM/S_CH_WD_MAP_ACC (how obvious was that)
5. IMPORTANT: Set your LOGSYS in /SAPSRM/CL_PDO_VALHELP_FACTORY class - love those those factories (tic)
DATA: lo_helper TYPE REF TO /SAPSRM/IF_PDO_ACCT_ASSGT_HLPR,
CALL METHOD /SAPSRM/CL_PDO_VALHELP_FACTORY=>GET_ACCT_ASSGT_HELPER
RECEIVING
RO_ACC_ASSGT_HELPER = lo_helper.
CALL METHOD lo_helper->set_searchhelp_control
EXPORTING
iv_logsys = ls_logsys-logsys.
6. Now handle event DATA_SELECTED to get data from SELECTION, and move to your Context field.
How simple was that? Yikes. I should have just built a custom dictionary search help to RFC over and call the BAPI for Cost Center List.
- Tim -
Hello.I wanted to upgrade my iPad 1 to iOS 5.1 Over the Air.I was running iOS 5.0.1.It said it had an error connecting to server.It is already 5 hours i cant install this update.I also have an iPhone 4 with iOS 5.0.1 with the same issues.Help please!
You're probably running into the servers simply being swamped. Thousands of people are all going for the software update at the same time. Give it a try again and if that doesn't work, then try plugging it into your computer and trying it that way.
I didn't get a notion of the size, it doesn't seem to be as big as the 700 meg 5.0 update, but it did take me 20+ minutes to download via cable internet so it's a large file. That in and of itself takes a while.
If you're trying to download it directly to your iPhone, you'll need to be on wifi since I'm sure it's well over the 20 meg file size limit for 3G. -
Recently i upgrade my iPad2 to 7.1(11D167) and now the wifi connection is very weak, I am not sure if it is a hardware or software issue, help please!
I am not sure, I have full signal on my iphone 5 and just 1 dot on my ipad, tomorrow I will test connection with other router and network, I thank you for your help and I will tell you the test result when done
-
While updating Apple TV now unit is locked up. Tried resetting with remote no help. Connected to iTunes Apple TV comes up to reset but when you hit reset fails and said it can't find any apple tv
Dear Brian:
Create a Play List in iTunes.
Control-Click and open "Export" in the highlighted Playlist in iTunes.
With "Export" opened:
1. Click on "Format" and choose "M3U";
2. In "Save As" name your "WhatEverNamePlaylist.m3u"; and
3. In "Where" tell the program where to send your "WhatEverNamePlaylist.m3u".
You are done creating the Playlist.m3u in iTunes.
Open "Subsonic Web Page".
Left hand column open "Import playlist".
In "Import playlist" click "Choose File" and open the "WhatEverNamePlaylist.m3u"; you created in iTunes.
The "WhatEverNamePlaylist.m3u" should now occupy the space between "Choose File" and "OK".
Click "OK".
The file should now be in the "Playlist" on the left. -
Hallo
Im work as a help desk . i use remote desktop help windows 7 but some time i have to wait 10 min to the end user because he is not in his place or ...
can i use another software without enduser permission? if yes then wich one
ThanxHi,
Based on my research and test, it's impossible. Even shortening time is also unreachable.
Karen Hu
TechNet Community Support -
TV@nywhere Plus remote issue resolved!!!
I have been searching and reading many posts to fix my remote issue / not working problem. I have had a MSI TV@nywhere Plus TV tuner for like a year and the remote never worked. I don't know the exact model number of the tuner card. I know my driver for the TVR is 2.0.2.2. I have the software that has the PVR Plus. I had seen several posts that link the issue to running the Initervideo Cinema Manager which I ran and I still did have any luck. So I uninstalled Intervideo WinDVD (which I did and this did not resolve the issue either) I left this program uninstalled an I searched the CD for some info.
The CD I have has a version number on the bottom around the hole MSI_7131_V1.1.
I found a program called P3XRCtl.exe that has a icon of a remote in the path E:\PCI\TVUtility (this is on the CD). I copied this program to my desktop and then clicked on the icon. Guess what, it worked!!! All of the functions on the remote work. It seems as if when I installed the software that this remote software/utility did not get installed and does not run when the TVR program starts. So I then created a folder in my program files to place this exe file. The path I placed it is C:\Program Files\MSI\TV@Anywhere Utilities (I created the TV@Anywhere Utilities folder) The MSI folder now has 2 folders called TV@Anywhere Plus & TV@Anywhere Utilities. I still had a problem of the program not starting when I start the TVR program so I added the exe file to the Startup folder. To do this create a shortcut to the exe file and place this new shortcut in C:\Documents and Settings\All Users\Start Menu\Programs\Startup
This program will now start everytime the computer starts and the remote should work when the TVR program is started. I am running Win XP Pro...This is wonderful I just solve my problem with the Remote Control, I Follow the suggestions from this people and my problem is fixed... now I can use it. Thank You very much
-
I've just finished projects with a bit of animation and some
branching that I facilitated with additional buttons and
duplication. Published for the web it works perfectly. My
instructor (I am a student with a co op in elearning) has asked for
an .exe version to present, and I'm having issues with that. Some
animation is freezing ( made with FLASHCS3 but just simple things
w/little AS3),in addition, the problem that some animation slides
with buttons are proceeding on their own. The navigation I added to
my "review" slides with buttons aren't pausing the animated slides
at all. Most difficult is that the issues vary ( so I can't just
alter certain slides)The branching elements are fussy,too...
sometimes the buttons stick, sometimes the branching is ignored and
a slide plays the next duplicate slide when it shouldn't (it should
branch to a designated slide). The other format works perfectly.
HELP I need a quick fix...I have a fast computer with enough
memory, good graphics card, updated drivers, and updated adobe and
microsoft everything...running vista sp1---So I know It must be
me...How can I get this in shape to run ASAP?
regards,
susanne> I've just finished projects with a bit of animation and
some branching
> that I
> facilitated with additional buttons and duplication.
Published for the web
> it
> works perfectly. My instructor (I am a student with a co
op in elearning)
> has
> asked for an .exe version to present, and I'm having
issues with that.
> Some
> animation is freezing ( made with FLASHCS3 but just
simple things
> w/little
> AS3),in addition, the problem that some animation slides
with buttons are
> proceeding on their own. The navigation I added to my
"review" slides with
> buttons aren't pausing the animated slides at all. Most
difficult is that
> the
> issues vary ( so I can't just alter certain slides)The
branching elements
> are
> fussy,too... sometimes the buttons stick, sometimes the
branching is
> ignored
> and a slide plays the next duplicate slide when it
shouldn't (it should
> branch
> to a designated slide). The other format works
perfectly. HELP I need a
> quick
> fix...
First thing I'd do is take out anything that uses AS3.
Captivate 3 doesn't
understand it ... and who knows, maybe that's messing
everything up for you.
Typical troubleshooting here would be to strip out anything
remotely
'exotic' and publish. If that works, keep adding things back
in until
something breaks.
The easiest way you could approach this might be to
copy/paste your current
project into a new one, one slide at a time, publishing and
testing between
slides. Once you know what bits break your published file it
will be easier
to figure out what needs to be fixed.
HTH
Steve
http://twitter.com/Stevehoward999
Adobe Community Expert: eLearning, Mobile and Devices
European eLearning Summit - EeLS
Adobe-sponsored eLearning conference.
http://www.elearningsummit.eu -
the remotes suddenly stops working, no power, nothing. new batteries are not helping. this is the second one to have this problem and customer service is of little help except to say get a new one. can anyone help?
One way of checking to see if the infrared component of the remote is working at all is to point it at a camcorder or digital camera or cell phone camera and see if a bright light appears when you press the button. If so, you know that the remote is at least outputting data. Now then the issue is to determine if the remote is programmed properly and outputting the proper code sequence. No chance the receive window in theSTB is blocked, dirty, or behind a glass door in an entertainment center, is there?
I've also had remotes whih went stupid periodically is the batter contacts are loose, dirty, or worn. One of my old remotes would have to be reporgrammed each time the batteries were changed. -
Novation ReMote : Please help !
Hi,
I´ve just purchased a Remote 61 and I´mn totaly disappointed with this tool. Ok, the keys are great and the knobs looks good, but how can I use it to controll Logic Pro 7.1 ??
I did all thing which are described in the manual. So I changed the prference files , I loaded the Logic 7 remotLSO, but nothing works.
It´s nearly uselesse at the moment and I´m really depressed, cause I thought that I am able to controll a lot of AU instruments as well as Logic too.
I would like to know if somebody here in that forum can show me a way how I can use the Remote with the templates. Or maybe someone has written his own template which works fine ?
Thank you very much , all help and hints are welcome so much .
best regards
udapI own a Novation Remote as well and like any MIDI controller, it takes learning how to setup your MIDI controller to work with your DAW. If you read the Novation Manual, download the appropriate template editor, drivers, etc... then you'll be up and running in no time. It took me about 2 days to build all of my templates (for all the synths) and get total control of logic just using the Remote. Just have patience. One thing I've noticed though is the Novation drivers seem to be very buggy in OSX Tiger. I've had continuous crashes with the Remote and my friend just installed the Novation Remote and said Logic has been crashing on him since installing it. So, if you can, run the controller through an Audio interface to avoid potential issues.
-
Time Capsule Remote Access [HELP]
So like the title says I want to have access to my Time Capsule from anywhere.
I'd like someone to post a [HowTo] Step by Step.
I have:
MB Pro with Lion OSX 10.7.4 (Airport Utility 6.1 and 5.6)
TC with FW 7.6.1 (Bridge Mode)
T-Home Speedport W 504V configured as a DSL-Modem
TC is connected to the Speedport.
I've read many things but they make everythin more complicate.
I also tried to activate NAT-PMP with a public IP so that I can Share Disk over WAN, but the program tells me that
DHCP Staraddress and Endaddress are in conflict with my WAN-IP-Address.
So at the moment I'm using the Bridge Mode.
Also iCloud "Back to my Mac" tells me NAT-PMP or UPnP isn't activated on my router.
So please give me some help with this stuff so I can get access from an extern network.
And if I try to do it on Airport Utility 6.1 it tells me Double NAT.
Regards
Khanh DuyI don't have a howto step by step sorry.. I refuse to use OS with as bad a Networking as Lion.. and no interest in clouds..
You can do this without icloud at all. And it is simple if you have a static public IP address.
Even without static public IP you might do ok with the modem you have.
So let me suggest 3 possibles..
1. If you want to continue down the icloud road.. the issue is upnp .. did you turn on upnp in the modem.. if not do so and try it. TC should be bridged.
Or if you ISP allows pppoe authentication then bridge the modem and use the pppoe client in the TC.. this is a better method as then the TC gets the public IP on its WAN port. You can select to allow disk access from WAN. Although if this is necessary or not from iCloud I have no idea.
2. With a static public ip, simply port forward AFP to the TC ip address. I will not post the details unless you do have a static public IP because most people don't. TC is in bridge.
3. Use dyndns client in the modem.. Here again you will have to check if that facility is in the modem.. again the TC is in bridge.. port forward AFP to the IP of the TC. The router has to control this using a fixed IP to the TC.
In both the case 2 or 3, you access the TC remotely by simply using its IP address or URL. In finder, go, go to server and type in AFP://PublicIPaddress or AFP://TCdyndnsaddress
If you just google for "Time Capsule remote access" there are hundreds and thousands of posts explaining how to do it.. but if you cannot figure out method 2 or 3.. I am happy to give further details. -
HELP! I taught myself PageMaker 6.5 and I got REALLY good at the basics, but not so great at the in-depth things. Consequently, when I upgraded to InDesign CS4, the same holds true, so please feel free to treat me like a 2-year-old in your explanations. Now for my dilemma:
I create a quarterly magazine. Most of the pages are 2- or 3-column spreads. Many times, a photograph (and its caption) will span more than just one column, but not necessarily the entire width of two. In other words, my photo could span all of column 1 and 1/2 of column 2, with the text flowing to the right of the photograph, then expanding to fill all of column no. 2 beneath it. In PageMaker, when I text-wrapped around the pic, leaving enough bottom text wrap to insert my captioning, the text would wrap perfectly, keeping the text in perfect alignment horizontally across the columns. That, in turn, kept the bottom edge of all my columns exactly equal.
In InDesign, however, that's not the case. The text doesn't align equally horizontally across the columns, hence ruining my clean horizontal text margin at the bottom. This happens any time I have a photo that spans all of one and part of one (or two, in the case of a centered photograph) column. In fact, even if I place a photo that fits within just one column, the horizontal text alignment gets screwed up. I'm attaching a .pdf of page 35 of the issue I'm working on to show you what I mean.
I've tried choosing all three columns and clicking the "align top edges," but that just drags all three columns up to the 1/2 inch margin at the top of the page, and my text actually starts 1/4" beneath that (3/4" from the top page edge) because of the page numbering, and when I drag all three columns back down to the 3/4" mark, the wrapping gets all screwed up again. So I tried "align bottom edges," and that didn't work either (it worked to a point... anything that actually had text flowing to the bottom of the column was fine, the same thing occurred then above the column with a photo spanning all of it. Geez, I'm confused just trying to explain it. Hopefully, the attached .pdf will help make sense of this.
Consequently, I'm moving columns manually for this issue (all 60 pages of it), because it has to be at the printers by the end of the weekend and I'm just plain out of time. If anyone can give me some guidance so I don't have to do this again next time, I'd really appreciate it.
You can email me at [email protected] if you have any ideas. Thanks for your help.
BarbThanks so much to both Peter and Bob. I'm sure this will fix the problem. At least I know it wasn't something I was doing wrong and it really is a glitch in the program. I'll play with the baseline grid, since it seems that will be the best option. I have a few months to experiment with it before the next issue goes to press.
Does setting a preference act like a default? In other words, will it then apply to all pages in all new documents I create or is it specific to the document in which I'm working when I set it? If the latter, I'm guessing I can just include it when I set up my master page so it will apply throughout the issue? Which, of course brings me to yet another question: how do I save my Master Pages so I don't have to redo them with each issue?
I'm finding that the majority of InDesign is a lot more user-friendly and easier to navigate than the old PageMaker -- many fewer steps for the same end result. I hope to take a class if I can find one in my area, because I'm certain I'm doing many things the "hard way." Learning as you go is okay, but you miss a lot of the finer points along the way and spend entirely too much time trying to figure things out or bugging people like you in this forum.
I apologize if some of what I ask seems rather elementary.
And Scott, sorry, but I've always felt that, out of all the fonts available, Comic Sans is the most readable.
Barb -
Officejet Pro 8600 Plus connection issue - HELP!
I have a strange issue: after some hours, the communication link is dropped between the computer and printer. When this happens, IE becomes unusable and will not connect to anything. This is replicated on three XP home machines. The fourth, a vista ultimate machine, does not seem to be affected (yet). I get the "scan to computer is disabled" error. It cannot be re-enabled. At this point I cannot print either. I can reach the embedded web server on the printer via firefox and can still surf using firefox. I can ping the printer, but again once the connection is dropped, no printing or scanning to the computer. The only thing I've found that resolves the issue (temporarily) is to reboot the computer, which just starts the cycle again.
last night I installed the software on an XP machine and the laptop to test when the connection dropped. They lasted from 7pm Monday until I got home at 5pm Tues. The machines were not used. Once I started using them (firefox only), then they dropped the connection within a half hour of each other around 7pm. The other XP machine lasted from 7pm Mon until 7am tues, when my wife started using it and then noticed it dropped sometime that tues between 7 and 9AM. An 11am tues reboot ran OK until 10 pm tues when connection was lost again (and IE is now dead). The Vista machine has been running since 7pm monday until now (930pm tues) and still seems to be holding.
printer hardwired, to router, static IP, 100-full link speed (also tried 10-half)
router dlink di-655
two XP machines are hardwired, vista is hardwired, and last xp machine is a laptop on wireless.
I've swapped cables rebooted and reinstalled multiple times. I must have a file a mile long on the support phone line. They were unable to fix it. I asked this to be escalated, but who knows when I'll get a response.
I've toggled firewalls - XP built in
I've uninstalled anti virus software
I've even put up with crazy suggestions from tech support like changing the router channel (uhh, it is wired!)
one xp machine had an AIO 4215 hooked via USB and the others printed to it via network, but the printer has been deleted from the networked machines.
I can ping 127.0.0.1 which is supposed to indicate the tcp service is OK.
I have not reset winsock .. I can see one machine being bad, but three????
malware / virus scan shows no issues. Again one maybe, but three??
The only thing I can think of is that there is something in the XP networking stack that conflicts with the new 8600 software as hours pass. Perhaps there is some polling operation that goes on then dies after some time, then it kills IE as it dies.
When the printer works it is great, but rebooting is not a permanent solution to this.
any suggestions would be greatly appreciated!!!!!! I am stumped and so is tech support. They are sending it to engineering, but who knows when they will respond.
thanks in advance.
This question was solved.
View Solution.well it looks like I have a working solution ... I downloaded a freeware file called process.exe . I made a cmd file via notepad with the following contents:
rem this is to keep the HP network printer communicating with the desktops
rem
process -k "hpnetworkcommunicator.exe"
rem
process -k "scantopcactivationapp.exe"
rem
"C:\Program Files\HP\HP Officejet Pro 8600\Bin\HPNetworkcommunicator.exe"
rem
Start "" "C:\Program Files\HP\HP Officejet Pro 8600\Bin\ScanToPCActivationApp.exe" -deviceID CNXXXX:NW -scfn "HP Officejet Pro 8600 (Network)"
the XXXX is your printer serial number with an extra character or two. Pull that number from the port tab after you pull up "properties" for the 8600 printer.
This cmd file basically restarts the printer link. It opens a command window that launches the program to re-establish the link.. then it closes the command window. The launched program shows that the communication link is dead (just for a few seconds), but then it makes the connection... THEN you hit the close button and coninue your work until it dies again.
I may have it autorun every X hours if I can narrow down a good time. Until then I have a shortcut on the desktop to "FIX HP LINK" ... I only had to do this for my XP machines, as the vista one seemed OK.
What ticks me off is that I shouldn't have to do all of this diagnosis. It would be nice if there is a fix in the pipeline so the link stays stable al the time. I've spent hours trying to figure this crap out.
Anyhow, I hope the time I spent helps someone. PS, thanks to the OJ6500 thread that had the info for the scantopcactivationapp.exe program.
PS ... I'm still waiting for an engineer to contact me, if any HP employees are reading this.
PSS I haven't tried this without killing and restarting the hpnetworkcommunicator stuff, but it works for now. -
Authorization issue - help request
Hi guys,
One of the consultants is having an authorization issue ( He is not abele to run a t-code)
I ask him to run a su53 report and i am not sure how to proceed with this.
Please help.
Here are the details from the SU53 report.
DISPLAY AUTHORIZATION DATA FOR USER VYXXXX
User : VYXXX profile parameter authorization buffering 4
Authorization Object: F_KNA1_GRP
Description
Authorization check failed:
+ Authorization object F_KNA1_GRP Customer Account Group Authorization
Activity 08
Customer Account Group ZM01
Users Authorization Data :
+ Authorization object F_KNA1_GRP Customer Account Group Authorization
Authorization T-PD19002300
Authorization T-UG39000900
Authorization T-UG39001000
Please help me guys what need to be performed.
Regards,
Vamsi.Hi Vamsi,
SU53 shows us the last failed authorization for a user. However, it might not only be the failed authorization object failed.
Hence, "just to learn" , you can use transaction ST01 to enable and run a trace for particular users. Be sure to use in a test environment first, and with proper filters. (for a particular user only).
Then check-> which auth object is failing.
RC=4 means a object value is failing.
RC=12 means an object is missing!
Check, which tcode is calling that object and this tcode is present in which role. Then.........proceed.
You can check the SAP documentation on running traces on the help portal of SAP. I think you will find the answer yourself by troubleshooting more and may be massaging some test roles here and there!
Likewise, if you are new to security, I would encourage you to start by reading some books on SAP security. Authorizations made easy is a good book to start with.
Let me know if you have any questions
EOD for me :P . take care
Abhishek
Maybe you are looking for
-
When sending a pdf as an attachment I cannot scroll through the pdf. Nor can I look at Outlook 2010
Frequently I create a pdf and then I want to send it. After clicking send and the email pops up I compose the message. However, as I compose it, I have a question requiring me to look at the pdf. However, I can't page through the document because
-
Retrieving Chinese Characters from SQL Server with JDBC
Im having problems correctly recieving Simplified Chinese from the database (SQL Server 2000). Driver: sun.jdbc.odbc.JdbcOdbcDriver It seems that I cannot force the Results Set's getString(String s) method to the correct character encoding UTF-16. Ja
-
MSS iview talent profile internals
hello experts, in the MSS iView talent profile (See help link below) http://help.sap.com/erp2005_ehp_04/helpdata/EN/9e/71dad0aba74a62a07bdee6edf8d91f/content.htm information is presented in two visual areas (left and right): 1. the left side shows in
-
Is it possible to go back to Mavericks OS X from Mavericks OS X Server?
hello. is it possible to go back to Mavericks OS X from Mavericks OS X Server? cannot find any info about uninstall of Server App thanx
-
Why isn't my app store password working?
Whenever I try to by a new app when it asks me to type in the password it keeps saying its in correct